Bootcamp partition unusable after the failed kidnapping attempt

Similar Questions

• Bootcamp for repair after the partition

  Hello

  I've done research on how to repair the bootcamp partition, but it seems to be that everyone either has corrupted the partition is before El Capitan and the old disk utility or had more than 4 GPT. While on my own, I have 4 partitions and all my files are readable on osx

  When I boot in windows (select the startup disk Bootcamp) I am satisfied with the legendary "no boot device - insert boot disk and press any key".

  

  

  Is anyone able to find a reason why it is not booting?

  Assuming you have a Mac which is 2014 or more, and the version of Windows is W7/W8.1...

  A. we need to disable SIP.

  1. boot in local restoration (command-R).

  2. start utility-> Terminal.

  3. type csrutil disable in the Terminal, and then press enter/return.

  4. type csrutil State.

  5 start normally, then type csrutil status to confirm that all of the individual entries are still disabled.

  B. fix the Windows MBR Boot-ability entry. Please ignore the i386 MBR error message, but not others

  sudo fdisk e/dev/disk0

  p

  setpid 4

  07

  Pavilion 4

  p

  w

  There

  Restart and test.

• Bootcamp partition disappeared after fdisk commands

  Hello

  I have a serious problem caused by my own stupidity,

  I tried to resize my partition, bootcamp, with no success, of course.

  Here is what happened,

  I resized the MAC OS X partition and made a new 100 GB. Then I tried to restart Windows that did not work.

  A black screen appears not saying no device found Boot... Insert and press a key.

  I rebooted to mac OS X and searching the forums, I ended up find a thread of a few years.

  He said try a few commands to disc, I did, it didn't work. Then I have a little "creative / reckless" and tried between the two commands.

  I guess I deleted or seriously damaged my MBR, although it could be a TPG. I do not know.

  Now, I can't see my Bootcamp partition in the finder.

  I see the size of the partition in the disk utility application, if I look at the full hard disk partition scheme

  

  It's the score 'Naamloos' is where bootcamp has been stored and as you can see I can't access it or what so ever.

  However in the terminal, I can see the partition

  

  My question is, if I can restore this partition?

  And if not, I can see the data on that partition?

  A lot of work not saved is there and final exams are almost!

  I'm sorry for the post probably not correct 'according to the rules of the forums"and the faulty use of the language and the incorrect spelling.

  1. what version of Windows?

  2. What is the year/model of your MBP?

  3 Please after the release of

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  sudo dd if = / dev/rdisk0s5 account = 1 2 >/dev/null | hexdump - C

• Bootcamp partition, disappeared after trying to install windows 10

  Hello world.

  I tried to create a bootcamp on my MacBook (13 '' MacBook Pro 128 GB early 2015) and the computer restarted then that partition the drive. The 32 GB, I put in the training camp are now "deleted" from the drive, and I can't find them.

  Please after the release of the next command in OSX Terminal.

  Cs diskutil list

• Dynamic JDBC: account blocked after the single connection attempt

  Our database is set up so that user accounts are locked after 3 bad connection attempts, but they're getting locked after only 1 attempt. I would like that it so that any attempt to connect ADF would be only created an Oracle connection attempt.
  I use JDeveloper 10.1.3.4.0 and by default, right click and then run.
  
  Code of the not yet documented Steve Muench ADF application examples at http://blogs.oracle.com/smuenchadf/examples/#14
  which is also described in http://www.oracle.com/technology/products/jdev/howtos/10g/dynamicjdbchowto.html
  
  Looking at the audit trail, I see the database tries to connect 5 times than the user.
  Trying to debug, I see that the doFilter in ADFBindingFilter is also called 5 times.
  
  In my research, I read the proposals that it might be the framework that tries to connect several times. It depends on the connection pooling and application module pooling settings you have.
  But I tried searchign in JDeveloper and don't see not where I set or change anything on reunification.
  
  Thank you
  
  Jeff

  Oracle has finally acknowledged it is a defect of jdeveloper and entered
  Bug 9153659: JDBC DYNAMICS IDENTIFICATION ACCOUNT LOCKS AFTER 1 FAILED CONNECTION information
  And I have no idea how oracle reactive is subject of fixed bugs, but since the last version of jdeveloper 10 numbered fixed iin bugs 5 millions, I guess that this will never be corrected.

• Recovery gone HD and Bootcamp starts rained after the Mac HD reduction in disk utility

  With the help of El Capitan, mid-2012 17 "Unibody Macbook Pro Non-retine

  Hi, I am trying to disable SIP with csrutil but I can't use this method in the recovery mode. Why? I had a problem where I have narrowed my Macintosh HD partition in disk utility and now my Bootcamp partition became start older (data still there).

  I was going to fix the partition table that caused problems with the boot, but when I loaded the Recovery Mode the thing wouldn't start and cling to a completed loading bar (with the apple logo, it took a lot of time to get the bar too full).

  So, I deleted the recovery partition HD and reinstalled OSX to retrieve. Problem is, he does not come back. Right now I have 4 partitions - disk0s1 is EFI disk0s2 is Macintosh HD disk0s3 is Untitled (free space), disk0s4's Bootcamp.

  Is it possible to UN-mess-up my hard drive without losing data? Sorry!

  ShinkoNet wrote:

  With the help of El Capitan, mid-2012 17 "Unibody Macbook Pro Non-retine

  Hi, I am trying to disable SIP with csrutil but I can't use this method in the recovery mode. Why? I had a problem where I have narrowed my Macintosh HD partition in disk utility and now my Bootcamp partition became start older (data still there).

  I was going to fix the partition table that caused problems with the boot, but when I loaded the Recovery Mode the thing wouldn't start and cling to a completed loading bar (with the apple logo, it took a lot of time to get the bar too full).

  So, I deleted the recovery partition HD and reinstalled OSX to retrieve. Problem is, he does not come back. Right now I have 4 partitions - disk0s1 is EFI disk0s2 is Macintosh HD disk0s3 is Untitled (free space), disk0s4's Bootcamp.

  Is it possible to UN-mess-up my hard drive without losing data? Sorry!

  The way is to not lose data have a current backup plan in place.  How to create a clone of startup

  SIP is the Protection of the integrity of the system and is a security featutre is not supposed to be cancelled esp of the 'system' you are primed to which would frustrate the object, so it must be done in an another boot drive - in your case.

  Your best bet is maybe to start int Internet recovery - this is done by now the keys option command R to reboot.  And go from there.

• Satelite P300 does not start after the failed Bios Update

  Hello world

  I tried to update the bios of a P300 to this:
  18/03/10
  Update the BIOS
  Toshiba Windows 7-32 Bit 4.20 - WIN32 World Wide
  That I downloaded here: http://uk.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=UK after entering my laptops specs.

  The process flash hanged during the update and the laptop became screen starts, blank when turning on and nothing else...
  I tried to use the Phoenix of emergency crisis, created a diskette with the file Bios image that I downloaded but nothing succeeded.

  Access to the floppy drive USB floppy when you enter the recovery mode, I hear the beeps that indicate that a process is carried out, but when everything stops and restart... the problem remains.

  -Does anyone have a clue what to do next?
  -The warranty is void after a bios update attempt?

  Thank you for yor time.

  > - Someone at - it an idea what to do next?
  Well in this case, you will need to contact a local ASP (Toshiba authorized Service Provider).
  Guys could clean CMOS and flash the BIOS ROM module with a BIOS disk special crisis

  You will find here all the FSA all over the world:
  http://EU.computers.Toshiba-Europe.com-> support download &-> locate an authorized Service partner

• T61 - BSoD after the BIOS update attempt

  Hello everyone,

  I was trying to update my BIOS because I had problems with my hard-drive (enclosure) recognized by my laptop, and I thought it would solve the problem. Now, my biggest problem I have is a bluescreen set up after the failure of the attempt to update the BIOS.

  How can I go about to fix? solve problems? recommendations?

  I would be very happy to help.

  BIOS rarely (almost never) fixes the problems, unless it is specifically published to solve a problem which you are confirmed as having. No one should attempt to update a bios on a system with a problem, you may destroy the card system, but in your case, this may be very simple. If your operating system has been installed with controller sata in compatibility mode, then update the bios will implement the default SATA mode and windows will be "blue screen" when starting. Enter the bios and change SATA setting to the report and the compatibility mode.

  If that does not turn, after more info on your system, all on the label located slot except the serial number. and your version of windows.

• White screen after the Fail Safe Mode - XP, graphics, nVidia, graphics card

  Recently, my office computer Gateway running Windows XP was invited to update the nVidia GEForce 6100 driver.

  I went to update this driver.

  On the next boot, I waited several minutes, but the computer hung up on a screen empty AFTER the Windows screen.

  I tried to restart the computer normally several times, but still and always the white screen appeared after installing windows.

  I have my computer in Mode safe start, which I did. In safe mode, I disabled the graphics driver nVidia and restarted my computer. To restart the computer, it has actually reached to explore. However, in all the windows, I opened the image lag. Instead of a fluid scrolling, everything has been hectic.

  I have to enter the BIOS setup and clicked to start my computer in mode 'fail safe '. Afterwards, when I press the power button on my computer the blue light turns on, fan is running, and a single beep of the singular but NO picture on my monitor.

  I tried my monitor on another computer and it worked fine. I plugged the monitor into the gateway PC and yet, I get a black screen as if the Office Tower does not recognize the monitor.

  I thank you very much for any solutions or advice, you should be able to provide!

  All the best,

  -Evan

  Hello

  Please restart in safe mode, and then do the following

  Start - right click my computer - manage - Device Manager - adapt display - nVidia...

  Right click - Properties - driver tab - back driver.

  This should bring back your previous working driver.

  Please keep in mind that my answer is based on the information in your message. More the better I can answer, Slan go foill, Paul

• Sounds and Wi - Fi are unusable after the awakening of Windows XP SP3 of stand-by

  original title: XP SP3 cannot wake up from standby correctly

  I recently upgraded my system from Windows XP SP2 to SP3 and installed onenote 2010 professional office 2010 but still not active. I found if I maintain my system, and cannot be used as alarm clock, sound and wireless.

  When I click the speaker button, I can hear the sound of 'Bang', which implies a mistake, and a pop-up box displays saying that «...» No audio mixer table cannot be found... ». I can't play music or watch the video.

  When I find out wireless available in the range, he said: "another program manages wireless" these words. But I have installed no utility to manage my wireless.

  There could be another problem. So far, I find just above two.

  After the system restarts, everything is recovered, until next time, I stand by my system.

  Hi Edwin.Xi,

  Given that you have upgraded your system from Windows XP SP2 to SP3, you may need to consult the manufacturer's Web site and download and install the latest version for Wi - Fi and sound drivers and check if that helps:

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  You can view the following articles in the KB for more information:

  How to solve the problems of hibernation and standby in Windows XP

  http://support.Microsoft.com/kb/907477

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to find the failed connection attempts at 'check' session is enabled

  How to find the unsuccessful connection attempt to dba_audit_trail when the "audit logon" is enabled.

  Filter your query against dba_audit_trail action_name = 'CONNECTION' with returncode! = 0 (returncode = 0 means that there are no errors - successful connection attempts)

• Smartphones from blackBerry Bold 9900 unusable after the attempt to update software

  Yesteraday I started operating system up-to-date software (from 7.1.8xx to 7.1.2xxx I think).

  After a while, the screen showed "App Error 602" and "Reset".

  Do a reset via the abovementioned display or pop battery option simply returns the device to the same State.

  I tried to download BlackBerry Desktop Software (710_b42), seemed to acknowledge a problem initially and offered to reload the software (at the cost of losing my apps, etc.).  I tried and the procedure failed with:

  "There was an error in your software update"
  "A connection to the device could not be established.  Please ensure that the device is properly connected to the docking station or the USB cable, and the cradle or the USB cable is properly plugged into your computer.  Also to ensure that the device made of start-up operations.  Run the Application loader wizard again. »

  The physical connection is obviously not the problem since Desktop software has been able to detect that it is a 9900 and offered also to reload.

  Assistance would be most appreciated.

  I finally got o/s to reload.  I still don't know why it worked on the third attempt, but not before, but I'm reactivated and now functional.

• does not start after the fail of power - current

  The machine makes grinding noises rhythmically squaky again and again until I have pull the plug. By pressing the button start does not stop the grinding effort (to start). It allows you to return after a few hours, but this time, there is nothing. It seems that he is not getting enough juice to do more than run fans briefly.

  I took it to a store where they tried to sell me a new machine that I don't want. They were first it upward from the starting System. They defragmented and other stages of the interview, but failed to solve my problem. Alleged that it was the motherboard, memory, etc. I had NO problem before this last failure and run diagnostic in the shop in my previous city with no problems.

  The model is:

  HP Pavilion Elite HPE - 480 t series XM558AV #ABA

  I made no changes to my machine at all because he was running very well and does everything that I needed. The shop removed a memory stick that I replaced as soon as I got home.

  It feels like the machine is not getting enough power to turn on. Fans of turn and stop. The Start button is useless once it is pressed at the beginning and I have to remove the plug to stop attempts to start.

  Starting after power outage has had a problem with this device, but it would eventually start so far. Any suggestions?

  Hi Chris,

  Try the steps listed in the link below.

  http://support.HP.com/us-en/document/c01884928

• Partition problem after the recovery of the system with a single key 6.0

  I need your help!

  My Lenova Ideapad Y430 not more start and I had to restore the system with the recovery CD I burned with a recovery key 6.0. The restore process showed no defects and no error has occurred.

  Now, after restaring the system I only 0 with a C: partition (all program files, vista, drivers etc.) 104 GB and the 'part of recovery for a key' 14.75 working. D: partition where all my documents, pictures etc. are stored are listed, but idle and not accessible nor editable with the tool Vista Diskmanagement.

  No idea what I can do?

  You can download EASEUS partition manager. It will help you to reformat the D drive.

• How can I mount a partition encrypted after the start?

  Hi all

  So I know that if I encrypt an external hard drive, I have to enter a password when I connect the disk on my computer until the drive mounts. However, I now try to have only one partition of an internal hard drive that is encrypted. When the computer starts first of all, I see the password screen. But what happens if I don't want to open the score right away?

  If I cancel the password protection screen, is there a way to come back later when I want to access this partition?

  Thank you!

  Use

  Utilities > disk utility

  Select the volume that you want to install and click 'mount '.

  C.