Botnet traffic filter

Similar Questions

• Veracity of BotNet filter report?

  Company has a ASA5510 with BotNet traffic filter enabled on this subject

  When I go into the report (using ASDM) file, it shows me the Monitor-> Botnet article filter traffic-> infected hosts - > highest level of threat

  If I save it as a pdf file and the review report it shows my number of malicious software on different machines. If I go on this computer and running AV or Malwarebytes ot other tools I have ever detected

  What gives me this report?

  Kind regards

  Thomas

  The ASA will not remove the botnet from the computer. It will only monitor and intercept traffic to the network level.

  Then, when it is removed, it could be some AV or virus cleaning software on the host computer. But the ASA controls at the network level and blocks potentially.

  I hope that makes sense.

  Let us know if your question is answered.

  PK

• ASA 5505 transparent mode dosnt pass traffic

  Hi all

  need help

  ASA 5505 do not pass traffic as a cordon of brewing, how do you get traffic?

  ciscoasa # sh ver

  Cisco Adaptive Security Appliance Version 8.2 software (5)

  Version 6.4 Device Manager (5)

  Updated Saturday, May 20, 11 16:00 by manufacturers

  System image file is "disk0: / asa825 - k8.bin.

  The configuration file to the startup was "startup-config '.

  ciscoasa until 55 minutes 31 seconds

  Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor

  Internal ATA Compact Flash, 128 MB

  BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB

  Hardware encryption device: Cisco ASA-5505 Accelerator Board (revision 0 x 0)

  Start firmware: CN1000-MC-BOOT - 2.00

  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03

  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05

  0: Int: internal-Data0/0: the address is e4d3.f193.9486, irq 11

  1: Ext: Ethernet0/0: the address is e4d3.f193.947e, irq 255

  2: Ext: Ethernet0/1: the address is e4d3.f193.947f, irq 255

  3: Ext: Ethernet0/2: the address is e4d3.f193.9480, irq 255

  4: Ext: Ethernet0/3: the address is e4d3.f193.9481, irq 255

  5: Ext: Ethernet0/4: the address is e4d3.f193.9482, irq 255

  6: Ext: Ethernet0/5: the address is e4d3.f193.9483, irq 255

  7: Ext: Ethernet0/6: the address is e4d3.f193.9484, irq 255

  8: Ext: Ethernet0/7: the address is e4d3.f193.9485, irq 255

  9: Int: internal-Data0/1: the address is 0000.0003.0002, irq 255

  10: Int: not used: irq 255

  11: Int: not used: irq 255

  The devices allowed for this platform:

  The maximum physical Interfaces: 8

  VLAN: 3, restricted DMZ

  Internal guests: 10

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  SSL VPN peers: 2

  The VPN peers total: 10

  Double ISP: disabled

  Junction ports VLAN: 0

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect Cisco VPN phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  Registry configuration is 0x1

  Modified configuration of enable_15 to 20:34:47.689 UTC Wednesday 5 December 2012

  ciscoasa #.

  ciscoasa #.

  ciscoasa # sh run

  : Saved

  :

  ASA Version 8.2 (5)

  !

  transparent firewall

  ciscoasa hostname

  activate 8eeGnt0NEFObbH6U encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  I haventerface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  Shutdown

  !

  interface Ethernet0/3

  Shutdown

  !

  interface Ethernet0/4

  Shutdown

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  interface Vlan1

  nameif inside

  security-level 100

  !

  interface Vlan2

  nameif outside

  security-level 0

  !

  passive FTP mode

  outs_in of access allowed any ip an extended list

  outs_in list extended access permit icmp any one

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  no ip address

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  outs_in access to the interface inside group

  Access-group outs_in in interface outside

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:234e9b9c6c9c941a89e37011325b6d5e

  : end

  ciscoasa #.

  ciscoasa #.

  ciscoasa #.

  ciscoasa # sh - access list

  access cached list the ACL log stream: total 0, 0 (deny-flow-max 4096) denied

  alert interval 300

  outs_in list of access; 2 elements; hash name: 0xd6c65ba5

  permit for access list 1 outs_in line ip scope any a (hitcnt = 0) 0x7d210842

  allowed to Access-list outs_in line 2 extended icmp any a (hitcnt = 0) 0x5532fcc5

  ciscoasa #.

  Hello

  Exactly... Good to know it works now.

  Do you know why he needs the IP address (such as a transparent firewall)?

  The ASA will act as a transparent layer 2 on the right device to the network, but what happens when the ASA does not have a particular destination mac address... What would be the source ip address of the package? Ip address of the ASA. So that's the main reason why we need that.

  We use it also for traffic management and for AAA services (if authentication is used the ASA will send the AAA authentication request to the server) with the IP address of this source.

  Please check the question as answered, so future users can pull of this

  Julio Carvajal

  Costa Rica

• Cisco Scan host (Hostscan_3.1.04082 - k9.pkg)

  Hello community,

  I recently bought an evaluation license to check our remote users primarily, Advanced endpoint for our ASA5505 antivirus and firewall. What I understand, it's that this feature requires the above license and also Anyconnect Premium peer to be activated. My "show worm" indicates that these licenses are activated. See below.

  The devices allowed for this platform:

  The maximum physical Interfaces: 8 perpetual

  VLAN: 20 unrestricted DMZ

  Double ISP: Activated perpetual

  VLAN Trunk Ports: 8 perpetual

  The hosts on the inside: 50 perpetual

  Failover: Active / standby perpetual

  Encryption - A: enabled perpetual

  AES-3DES-Encryption: activated perpetual

  AnyConnect peers Premium: 10 perpetual

  AnyConnect Essentials: Disabled perpetual

  Counterparts in other VPNS: 25 perpetual

  Total VPN counterparts: 25 perpetual

  Shared license: disabled perpetual

  AnyConnect for Mobile: activated perpetual

  AnyConnect Cisco VPN phone: disabled perpetual

  Assessment of Advanced endpoint: activated perpetual

  Proxy UC phone sessions: 2 perpetual

  Proxy total UC sessions: 2 perpetual

  Botnet traffic filter: disabled perpetual

  Intercompany Media Engine: Disabled perpetual

  Cluster: Disabled perpetual

  This platform includes an ASA 5505 Security Plus license.

  Now to my question. What should I do to activate this feature? No matter what I try, the test of remote access from a Windows 8.1 with anyconnect 3.1.04072 all have access to the network regardless of my parameter in ASDM.

  That's what I did after actication of license and a reboot:

  1. from ASDM, 'Configuration'--> remote access VPN--> host Scan Image: Browse flash for

  hostscan_3.1.04082 - k9.pkg and enabled "activate host Scan/CSD. Then apply and save.

  2 restarted ASDM.

  3. from ASDM,--> Configuration--> remote access VPN--> Secure Desktop Manager--> host Scan set up Advanced Endpoint Assessment worm 3.6.8133.2--> added F-secure.

  4. apply and save.

  When I try to connect with my 8.1 anyconnect - machine Windows (with no F-secure antivirus installed) I see that the Anyconnect client makes a hostscan but no matter what I do the machine will ignore my settings for Antivirus, etc. and get full access.

  What Miss me? I have to create a DAP aswell, or shouldn't it work without one?

  Note: Our Anyconnect authenticate using RADIUS with stimulus / response, but I guess that would not affect as the host-scan will be performed prior to authentication.

  Thank you in advance,

  Best regards

  A DAP rule would take care of it. This is where you must create a rule to search for attributes of endpoint as process, files, the key to registry or something else. In light of criteria coupled or unmatched, you can decide to let them continue, quarantine or delete the connection. DAP rules are capable of much more, but from reading the above, it seems that you are wanting to do either connect or disconnect the installed AV-based. Does that answer your question?

  Thank you.

  Joe

• Cisco AnyConnect do IPsec?

  Hi guys

  I have a Cisco ASA5520 with software Version 8.2 (5) in place, most my users are Mac users and I am currently looking into Cisco AnyConnect in comparison using the VPN client.

  I have a few questions

  (1) Cisco AnyConnect does he use IPSec or is it soley based SSL VPN?

  (2) the license information I have in my ASA below, I understand that I can get max 750 vpn peers am however I have reason to say that this does not apply to Cisco AnyConnect peers? and with Cisco AnyConnect, I can only have 2 peers? Also, what are the options for mobility anyconnect for?

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 150

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  SSL VPN peers: 2

  Total of the VPN peers: 750

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect Cisco VPN phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  (3) when you try to configure Cisco Anyconnect on the SAA by using ASDM, I noticed that I needed to download AnyConnect client images, but when I did this by downloading the .dmg for mac machines file I got the error message 'not an image valid of the SVC'. Is it because I'm under 8.2?

  Your help is highly appreciated

  Concerning

  Mohamed

  Hi Mohammad,.

  I'll answer your questions one by one:

  1 cisco Anyconnect version 3.0 and above all support SSL and IPSECv2 connection. If you want the user to connect using the Anyconnect client IPSECv2 then it will consume the SSL license and not the IPsec license however if you use IPSECv2 for connections such as vpn site to site then it will consume normal IPSec VPN license.

  2. one.  SSL VPN peers: this license gives you information about the number of users that can connect using SSL protocol for example using the Anyconnect and web portal customer also known as the clientless VPN based on. I see here there are only 2 licenses so at any given time only 2 users can connect successfully because 750 is the total number of licenses available for the VPN on the SAA, 698 only will be available for IPSec connections.

  b. Anyconnect for mobile: this license is required whenever a user connects from a Pocket like device: Iphone, Ipad, tablets etc.

  c. Anyconnect of Cisco VPN phone: Cisco IP phones have the ability to connect to an ASA remote using the SSL protocol and to enable this feature, you should have this license is activated on the SAA.

  d. Anyconnect essentials: Anyconnect there are two licenses, one > Anyconnect Premium and b > Anyconnect Essentials. AnyConnect essentials is less expensive as premium per report Anyconnect license. This license is for those who don't use webvpn or VPN without client. When the license is activated, the user can connect only to the Anyconnect VPN client.

  3. I don't know what image you use on the ASA. Please try the image named as anyconnect-macosx-i386 - 2.5.2010 - k9.pkg.

  To apply the changes using the command line, put this image on disk0: and then type this command on the CLI.

  Image disk0:/anyconnect-macosx-i386-2.5.2010-k9.pkg SVC

  Let me know if it helps.

  Thank you

  Vishnu Sharma

• "Move" failover to different / interface port

  Sorry if this is in the wrong place, we had if rarely to issues which were not covered otherwise I frequent this area.

  How is it difficult to change the interface used for active failover / standby? This is a pair of work, already configured with standby, but I need to move the cable crossed and tell them to use a different interface.
  Pair of ASA 5510, already put in place and work with failover, which was originally set on Ethernet port 0/3 by senior network administrator. It seems that its use of interfaces or ports he used things straight out of the examples on the web, including the interfaces used.
  The admin network senior retired last spring and left me "supported", gee, thanks.
  I need to make some changes and Ethernet port need for an important new project.
  The management interface 0/0 is unused and shut down. We manage by inside the interface from a specific inside subnet so do not need the interface dedicated management.
  I want to spend the shift IN management TO Ethernet 0/3 0/0

  * This is the current configuration:

  Output of the command: "sh run failover.

  failover
  primary failover lan unit
  failover failover lan interface Ethernet0/3
  failover failover Ethernet0/3 link
  failover interface ip failover 169.254.255.1 255.255.255.252 ensures 169.254.255.2

  * And it's the current 0/3 interface and management configuration:

  interface Ethernet0/3
  STATE/LAN failover Interface Description
  !
  interface Management0/0
  Speed 100
  full duplex
  Shutdown
  nameif management
  security-level 0
  no ip address
  OSPF cost 10

  I know that it can work on the management interface 0/0 because I see a lot of 'how to configure' as if the SAA is brand-new and several examples there indeed be setup on the management.

  I'm looking to find out how to take a pair of ASA is currently configured and has a functional work and all failover configuration simply "tilting move" to a different hole, or change the interfaces used for the 'heartbeat' somehow.

  I guess that's not difficult - but I also assume that there is a specific sequence of events that must occur in order to prevent the pair to enter the failover and switching of the main roles...
  For example - would have turned off or turn off the power switch and if so, how and on what ASA (frankly, I don't know how to access education secondary or standby if it needs to be done, suspended or on the rescue unit, because I never did that 'deep' a before config)
  CLI is very well - I'd be too comfortable in ASDM or cli.

  I really hope this makes sense - I have more than one convenience store and fixer than a designer or network engineer...
  And thank you very much - get this moved will release the interface I need and can really make a big bump in my list of project while the project manager is on vacation this week! I'd love to have done this and before his return.

  Oh, in case it is important as I said, it's running license and version shown here:

  Cisco Adaptive Security Appliance Software Version 4,0000 1
  Version 6.4 Device Manager (7)

  Updated Friday, June 14, 12 and 11:20 by manufacturers
  System image file is "disk0: / asa844-1 - k8.bin.
  The configuration file to the startup was "startup-config '.

  VRDSMFW1 141 days 4 hours
  failover cluster upwards of 141 days 4 hours

  Material: ASA5510, 1024 MB RAM, Pentium 4 Celeron 1600 MHz processor
  Internal ATA Compact Flash, 256 MB
  BIOS Flash M50FW080 @ 0xfff00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
  Start firmware: CN1000-MC-BOOT - 2.00
  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.06
  Number of Accelerators: 1

  0: Ext: Ethernet0/0: the address is 0024.972b.e020, irq 9
  1: Ext: Ethernet0/1: the address is 0024.972b.e021, irq 9
  2: Ext: Ethernet0/2: the address is 0024.972b.e022, irq 9
  3: Ext: Ethernet0/3: the address is 0024.972b.e023, irq 9
  4: Ext: Management0/0: the address is 0024.972b.e01f, irq 11
  5: Int: not used: irq 11
  6: Int: not used: irq 5

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 100 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  VPN - A: enabled perpetual
  VPN-3DES-AES: activated perpetual
  Security contexts: 2 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect Premium peers: 2 perpetual
  AnyConnect Essentials: 250 perpetual
  Counterparts in other VPNS: 250 perpetual
  Total VPN counterparts: 250 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy UC phone sessions: 2 perpetual
  Proxy total UC sessions: 2 perpetual
  Botnet traffic filter: disabled perpetual
  Intercompany Media Engine: Disabled perpetual

  This platform includes an ASA 5510 Security Plus license.

  Cluster failover with license features of this platform:
  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 100 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  VPN - A: enabled perpetual
  VPN-3DES-AES: activated perpetual
  Security contexts: 4 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect Premium peer: 4 perpetual
  AnyConnect Essentials: 250 perpetual
  Counterparts in other VPNS: 250 perpetual
  Total VPN counterparts: 250 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy UC phone sessions: 4 perpetual
  Proxy total UC sessions: 4 perpetual
  Botnet traffic filter: disabled perpetual
  Intercompany Media Engine: Disabled perpetual

  This platform includes an ASA 5510 Security Plus license.

  Serial number: ABC12345678
  Running permanent activation key: eieioandapartridgeinapeartree
  Registry configuration is 0x1
  Last modified by me to 15:03:07.132 CDT MON Sep 15 2014 configuration

  Disconnect an interface monitored on your rescue unit that will ensure that it does not take as active. Then cut the failover link and modify its failover parameters. (You will need to first remove the nameif for M0/0).

  Then, make the changes on the primary unit similar free game active. Reconnect the failover link, confirm the synchronization of the units and finally reconnect the interface of production on the rescue unit.

• Verification of the license of ASA5585-SSP-IPS40

  Hi team,

  I'm new to IPS and we have purched the ASA5585-SSP-40 device with IPS module

  model serial number of map od
  ---- -------------------------------------------- ------------------ -----------
  Security Services of 0 ASA 5585 - X CPU-40 w ASA5585-SSP-40 JAD17300013
  1. ASA 5585-X IPS Security Services processor-4 ASA5585-SSP-IPS40 JAD1728028W

  MAC mod Fw Sw Version Version Version Hw address range
  ---- --------------------------------- ------------ ------------ ---------------
  7c69.f682.95dc 0 to 7c69.f682.95e7 2.2 2.0 (13) 5 9.2 (1)
  1 bc16.6581.e4b0 to bc16.6581.e4bb 2.1 2.0 (13) 5 7.1 (1) E4

  The Application name of the mod status Version of the Application to the SSP SSP
  ---- ------------------------------ ---------------- --------------------------
  1 IPS                            Up               7.1(1)E4

  Data on the State of mod aircraft compatibility status
  ---- ------------------ --------------------- -------------
  0 to Sys does not apply
  1 up Up

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 1024 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  Encryption - A: enabled perpetual
  AES-3DES-Encryption: activated perpetual
  Security contexts: 2 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect Premium peers: 2 perpetual
  AnyConnect Essentials: Disabled perpetual
  Counterparts in other VPNS: 10000 perpetual
  Total VPN counterparts: 10000 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy UC phone sessions: 2 perpetual
  Proxy total UC sessions: 2 perpetual
  Botnet traffic filter: disabled perpetual
  Intercompany Media Engine: Disabled perpetual
  10GE I/O: activated perpetual
  Cluster: Disabled perpetual

  This platform includes a Premium VPN ASA5585-SSP-40 license.

  I wanted to check that licese is IPS is aviable on the devcie or do we stay purchse

  You are welcome. Please indicate your question as answered if it was and useful response rate.

• Features licensed on an ASA update

  The device is a Cisco ASA 5520 9.1 (4) running.

  Installing AnyConnect Essentials and AnyConnect for Mobile.

  Already have a license for AnyConnect Premium peer (10 users).

  I was wondering if I can simply install the new AnyConnect Essentials license regardless of the existing license Premium AnyConnect peers.

  I was wondering if the AnyConnnect for the Mobile license recognizes the number of users associated with the AnyConnect Essentials license or license Premium AnyConnect peers.

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 150 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  Encryption - A: enabled perpetual
  AES-3DES-Encryption: activated perpetual
  Security contexts: 2 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect peers Premium: 10 perpetual
  AnyConnect Essentials: Disabled perpetual
  Counterparts in other VPNS: 750 perpetual
  Total VPN counterparts: 750 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy UC phone sessions: 2 perpetual
  Proxy total UC sessions: 2 perpetual
  Botnet traffic filter: activated 281 days

  Intercompany Media Engine: Disabled perpetual
  Cluster: Disabled perpetual

  This platform includes an ASA 5520 VPN Plus license.

  AnyConnect Essentials and Premium AnyConnect can exist as the licenses on an ASA, but either one or the other can be used.

  Once you enter the command "anyconnect essentials", it allows to disable all features you may have configured to use the Premium license.

• 3DES ASA5505-50-BUN-K9 [resolved] license problem

  Hello

  I have ASA505 with disabled 3DES, I heard that I can have the 3DES free license, so I contacted cisco more of 10 times to get the permit, and whenever they send me the same license as my base standing key: 5321ec6e 102e534b fc21e96c 841c8ca8 ce1727aa

  I don't understand the problem, here is the result show activation key:

  Running Permanent Activation Key:
  
  0x5321ec6e 0x102e534b 0xfc21e96c 0x841c8ca8 0xce1727aa
  
  

  Licensed features for this platform:

  Maximum Physical Interfaces    : 8              perpetual

  VLANs                          : 3              DMZ Restricted

  Dual ISPs                      : Disabled       perpetual

  VLAN Trunk Ports               : 0              perpetual

  Inside Hosts                   : 50             perpetual

  Failover                       : Disabled       perpetual

  VPN-DES                        : Enabled        perpetual

  VPN-3DES-AES                   : Disabled       perpetual

  SSL VPN Peers                  : 2              perpetual

  Total VPN Peers                : 10             perpetual

  Shared License                 : Disabled       perpetual

  AnyConnect for Mobile          : Disabled       perpetual

  AnyConnect for Cisco VPN Phone : Disabled       perpetual

  AnyConnect Essentials          : Disabled       perpetual

  Advanced Endpoint Assessment   : Disabled       perpetual

  Botnet Traffic Filter          : Disabled       perpetual

  Intercompany Media Engine      : Disabled       perpetual

  This platform has a Base license.

  The flash permanent activation key is the SAME as the running permanent key.

  And the license key cisco send me whenever isexactely the same, but it should enable the 3DES encryption algorithm:

  Inside Hosts                    : 50        

  Failover                        : Disabled  

  Encryption-DES                  : Enabled   

  Encryption-3DES-AES             : Enabled   

  Security Contexts               : Default   

  GTP/GPRS                        : Disabled  

  AnyConnect Premium Peers        : Default   

  Other VPN Peers                 : Default   

  Advanced Endpoint Assessment    : Disabled  

  AnyConnect for Mobile           : Disabled  

  AnyConnect for Cisco VPN Phone  : Disabled  

  Shared License                  : Disabled  

  UC Phone Proxy Sessions         : Default   

  Total UC Proxy Sessions         : Default   

  AnyConnect Essentials           : Disabled  

  Botnet Traffic Filter           : Disabled  

  Intercompany Media Engine       : Disabled  

  Platform = asa

  JMX152040DW: 5321ec6e 102e534b fc21e96c 841c8ca8 ce1727aa

  

  Can someone tell me where is the problem please?

  Thank you in advance.

  Plug this serial number on the EEG of tool licenses the activation key that you noted but also the text:

  "ASA5500-BA-K9.

  Beware, our records indicate that the material Cisco ASA firewall serial NUMBER you have submitted your registration was previously the license FOR a larger feature SET. »

  What other licenses has been done on this SAA? Are you the original owner? You must call the TAC for sorting if you aren't.

• Cisco Anyconnect to mobile license?

  Dear all:

  Currently, we will activate cisco anyconnect for mobile (IPAD), our license is currently:

  Material: ASA5510, 1024 MB RAM, Pentium 4 Celeron 1599 MHz processor
  Internal ATA Compact Flash, 256 MB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 100
  Internal hosts: unlimited
  Failover: Active/active
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 2
  GTP/GPRS: disabled
  VPN SSL counterparts: 10
  The VPN peers total: 250
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect Cisco VPN phone: disabled
  AnyConnect Essentials: disabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  This platform includes an ASA 5510 Security Plus license.

  as I read, so cisco anyconnect for mobile (IPAD), I need two licenses:

  AnyConnect Essentials and AnyConnect for Mobile, is that correct?

  If I want to activate this just for 10 users, I can do this? What are the available license I have to select by the user issues a year (or over a year?)

  can my final question get these licenses from Amazon, since google shows as these offers.

  Please help thanks

  I would go for the license more. It is much cheaper then the VPN-only-license and you can continue to use it when you change the ASA in a newer model.

• Licenses of ASA

  Hi all

  We bought a new device of 5515 x ASA. I'm confused with the license available on the device.

  How many users can connect with the Anyconnect VPN client to the device?

  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 100 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  Encryption - A: enabled perpetual
  AES-3DES-Encryption: activated perpetual
  Security contexts: 2 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect Premium peers: 2 perpetual
  AnyConnect Essentials: Disabled perpetual
  Counterparts in other VPNS: 250 perpetual
  Total VPN counterparts: 250 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy total UC sessions: 2 perpetual
  Botnet traffic filter: disabled perpetual
  The IPS Module: Disabled perpetual
  Cluster: Activated perpetual
  Members of the cluster: 2 perpetual

  This platform includes an ASA 5515 Security Plus license.

  FC

  Philip AnyConnect 4.x licenses are NOT limited to a single ASA (or pair HA). It is a change of 3.x and earlier versions.

  You can exchange the PAKs against ASAs as are used for remote access VPN in a given customer.

  As long as you do not exceed the number of authorized users, you in the terms of the license. The number of users is not currently technically - applied is to the customer, such as advised by their dealer, buy the right level of license.

• Should what license I for 25 SSL VPN peers

  Hi all

  I want to implement cluster active / standby with a pair of ASAs 5550 and I have a licensing question. Here's the "sh - key retail activation" leave two output devices...

  ASA1:

  SH - activation in detail key:

  Serial number: XXXXX

  No temporary key assets.

  Activation key running: XXXXX XXXXX XXXXX XXXXX XXXXX

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 250

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  SSL VPN peers: 2

  Total of the VPN peers: 5000

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect Cisco VPN phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes an ASA 5550 VPN Premium license.

  Flash activation key is the SAME as the key running.

  ASA2:

  SH - activation in detail key:

  Serial number: XXXXX

  No temporary key assets.

  Activation key running: XXXXX XXXXX XXXXX XXXXX XXXXX

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 250

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  VPN SSL counterparts: 25

  Total of the VPN peers: 5000

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect Cisco VPN phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes an ASA 5550 VPN Premium license.

  Flash activation key is the SAME as the key running.

  --------------------------------------------------------------

  It seems so obvious that I have to upgrade the first ASA to support 25 SSL VPN peers in order to create the cluster HA, right?

  Now, I want to know do I need the license "ASA5505-SSL25-K9" or something else.

  Thank you very much in advance for any help!

  Ah OK I see - right then: upgading pole will allow the license to share.

  Re the version target, I would recommend going directly to 8.4 (4.1). I have it deployed on several sites without problem.

• ASA Cisco license issues

  Hello

  I'm new with Cisco licenses... I produced Cisco ASA 5505 in house with base with the limit of 10 hosts license. More information below.

  I bought the 'L-ASA5505-10-UL =' upgrade remove limit hosts and I got the certificate with Pak. But when I go to the licenses of Cisco website to get the key of activation with this PAK I you will get the error message below.

  Unfortunately I didn't take in charge of the contract so I can not open a Service request as said.

  Any help what to do?

  Error message:

  Bad Sku (s) 'L-ASA5505-10-UL =' for 'ASA5505-BUN-K9': device contains the licenses following "K9-BA-ASA5500.

  Serial number = JMX1526Zxxx

  We're sorry, but the serial number provided is not the same type of platform that serial number has failed. An upgrade is requested is not permitted.

  If you want assistance in solving this problem, please open a Service request by using the TAC Service request tool

  > View version

  The devices allowed for this platform:

  The maximum physical Interfaces: 8 perpetual

  VLAN: 3 restricted DMZ

  Double ISP: Disabled perpetual

  Junction VIRTUAL LAN ports: perpetual 0

  The hosts on the inside: 10 perpetual

  Failover: Disabled perpetual

  VPN - A: enabled perpetual

  VPN-3DES-AES: activated perpetual

  AnyConnect Premium peers: 2 perpetual

  AnyConnect Essentials: Disabled perpetual

  Counterparts in other VPNS: 10 perpetual

  Total VPN counterparts: 25 perpetual

  Shared license: disabled perpetual

  AnyConnect for Mobile: disabled perpetual

  AnyConnect Cisco VPN phone: disabled perpetual

  Assessment of Advanced endpoint: disabled perpetual

  Proxy UC phone sessions: 2 perpetual

  Proxy total UC sessions: 2 perpetual

  Botnet traffic filter: disabled perpetual

  Intercompany Media Engine: Disabled perpetual

  This platform includes a basic license.

  See you soon,.

  Henri

  It's an automatic response, or a person actually answered? License Rep must respond to your e-mail. They would be able to rehost the license for you.

• ASA 5505 Security Plus license question

  Hi all!

  I have an ASA 5505 that I test with first entered with the Security Plus license. Recently, I erased flash and loaded the latest version of asa841 - k8.bin of IOS with asdm - 642.bin. Everything starts very well and came as he does so freshly however I noticed that I was now running only a basic license. If I run the sh key activation order, I noticed the following messages (exit complete is downstairs):

  The activation key running is not valid, using the default

  ......

  This platform includes a basic license.

  ......

  Unable to retrieve the activation key permanent flash

  I somehow kill my Security Plus licenses when I did the flash erase? If yes how do I to get it back?

  Thank you!!!

  -ken

  ciscoasa # sh - activation key

  Serial number: JMXXXXXXHU

  Activation key permanent running: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000

  The activation key running is not valid, using the default settings:

  The devices allowed for this platform:

  The maximum physical Interfaces: 8 perpetual

  VLAN: 3 restricted DMZ

  Double ISP: Disabled perpetual

  Junction VIRTUAL LAN ports: perpetual 0

  The hosts on the inside: 10 perpetual

  Failover: Disabled perpetual

  VPN - A: enabled perpetual

  VPN-3DES-AES: disabled perpetual

  AnyConnect Premium peers: 2 perpetual

  AnyConnect Essentials: Disabled perpetual

  Counterparts in other VPNS: 10 perpetual

  Total VPN counterparts: 25 perpetual

  Shared license: disabled perpetual

  AnyConnect for Mobile: disabled perpetual

  AnyConnect Cisco VPN phone: disabled perpetual

  Assessment of Advanced endpoint: disabled perpetual

  Proxy UC phone sessions: 2 perpetual

  Proxy total UC sessions: 2 perpetual

  Botnet traffic filter: disabled perpetual

  Intercompany Media Engine: Disabled perpetual

  This platform includes a basic license.

  Unable to retrieve the activation key permanent flash.

  The permanent activation key flash is the SAME as the key permanent running.

  Hi Ken,

  If you know what the license and activation for your security key, you can simply re - install it with the command "activation key" from the global configuration mode.

  If you have lost the key, you'll want to open a support case to get it retrieved.

  Hope that helps.

  -Mike

• How much max VPN session is my ASA

  This is my version to see the ASA5512 VPN

  "Other peers VPN: 250" means that I can use 250 IPSEC session? If I still use MAX 250 VPN Cisco AnyConnect Secure Mobility Client session?
  "Total peer VPN: 250" means that I can use 2 Anyconnect premium + 248 250 IPSEC or IPSEC session at the same time?

  "AnyConnect for Mobile: Disabled" means, I can't use AnyConnect Secure mobility Client (smartphone apps) connect to the ASA by AnyConnect SSL? Can I use AnyConnect secure mobility Client (smartphone apps) connect to the ASA by IPSEC?

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited perpetual
  VLAN maximum: 100 perpetual
  Guests of the Interior: perpetual unlimited
  Failover: Active/active perpetual
  Encryption - A: enabled perpetual
  AES-3DES-Encryption: activated perpetual
  Security contexts: 2 perpetual
  GTP/GPRS: Disabled perpetual
  AnyConnect Premium peers: 2 perpetual
  AnyConnect Essentials: Disabled perpetual
  Counterparts in other VPNS: 250 perpetual
  Total VPN counterparts: 250 perpetual
  Shared license: disabled perpetual
  AnyConnect for Mobile: disabled perpetual
  AnyConnect Cisco VPN phone: disabled perpetual
  Assessment of Advanced endpoint: disabled perpetual
  Proxy UC phone sessions: 2 perpetual
  Proxy total UC sessions: 2 perpetual
  Botnet traffic filter: disabled perpetual
  Intercompany Media Engine: Disabled perpetual
  The IPS Module: Disabled perpetual
  Cluster: Disabled perpetual

  THX

  Hello!

  ASA5512 can contain up to 250 concurrent VPN of any type: IPsec Site to Site or IPsec Remote access or Anyconnect SSL VPN or IPsec IKEv2, or even without VPN client.

  This means you can use 2 Anyconnect premium + 248 IPSEC VPN from Site to Site. Or, for example, 200 simultaneous IPsec Site to Site VPN + 25 Client VPN (IPsec IKEv1) + 25 AnyConnect VPN (SSL or IPsec IKE v2). But not more than 250 and then at the same time.

  "AnyConnect for Mobile" is now obsolete. The license for Anyconnect schema was changed in early 2015. You can see the new pattern here:

  http://www.Cisco.com/c/dam/en/us/products/security/AnyConnect-og.PDF

  With the new scheme, if you need to connect mobile devices (iOS, Android and so on), using the Anyconnect client, you just need to have a license Anyconnect MORE for the necessary amount of users/devices. License AnyConnect more open along the lines in the output of the show version:

  AnyConnect Premium Peers : 250 perpetual

  AnyConnect for Mobile : Enabled perpetualAnyConnect for Cisco VPN Phone : Enabled perpetualAdvanced Endpoint Assessment : Enabled perpetual

  But, despite the exit "AnyConnect peers Premium: 250 perpetual", you will have the right to use no more then amount ordered... If you need advanced features, for example, Suite B cryptography or VPN without customer, you must order license Anyconnect Apex for amount of users/devices needed. For ASA5512, you need to order licenses Anyconnect more or Apex, but no more so for 250 users, because ASA5512 can't take no more then 250 simultaneous connections. If you want to use the Anyconnect client for mobile devices and you use IPsec IKEv2 for VPN, you will also need order licenses Anyconnect more or Apex. I hope this helps.