Brightness has only two settings after replacing the screen

Similar Questions

• System Restore to factory settings after replacing the hard drive?

  I have a Lenovo ThinkCentre A52, which recently required a change of hard disk and the removal of a defective RAM 1 GB stick. When I bought my computer, it came with Windows XP Pro and the new hard drive that the updated computer has Windows XP Pro, but it seems to be missing a large part of the software (drivers and programs) that originally came with the computer, and even if I downloaded and installed most of them since the Lenovo Web site There are still some problems related to software that I can't fix. Ideally, I'd like to go back just to restore the system to the factory settings using the ThinkVantage Rescue and Recovery program, but I don't know if it will work. All programs and the necessary drivers will be installed again, even if my current hard drive is not 'knows' thereon? I need to get a Windows XP Pro installation CD, if I want to keep my operating system? Also, is it important that my current hard drive is half the previous, or that I now have half as much RAM?

  Thank you

  After replacing the hard drive, the only way to restore it to the State of the plant is using the Lenovo installation diskettes. You can also ask if Lenovo has a solution to your problem without having to reinstall Windows.

  You can download Lenovo drivers if they are not included on the installation disk. The size of your hard drive does not matter.

  Lenovo - call to order recovery disks:
  http://support.Lenovo.com/en_US/product-and-parts/detail.page?&LegacyDocID=YaST-3P2QYL

• 2000 laptop... black screen after replacing the screen"

  I dropped the cell phone cracked screen, replaced the screen with a controlled with surgeons of the screen. Screen remains black, external monitor works. The brightness keys do not move the progress bar. All bars are gray. (assumes that the replacement is correct). Any suggestions?.

  Solved. I don't have a proper cable connection. All right.

• How can I restore my system to factory settings, after replacing the hard drive?

  Original title: I have a hard nine; how I can start or put in the back of the recovery disc to my old sistem all gane

  I need help to start the recovery disc, in all new hard drive, in order to restore my system whole back

  Hello

  You can boot from the DVD drive with the recovery disk and then follow the manufacturers installation instructions

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• HP pavilion dv6-7010us: low light on dv6-7010us screen after replacing the screen

  We recently replaced a cracked screen on our laptop and now the screen is very dark. You can still see that the computer is turned on, but it is difficult to use. The brightness level is completely upward and the f command button does not help. How can I fix the light from the screen?

  Hi @Nantucket

  Welcome to the HP Forums!

  This is a wonderful place to find answers and advice!
  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums Learn how Post and more

  I understand that you have recently replaced a cracked screen but the news is very dark.  You can see that the computer is turned on bu that it is difficult to use.  The brightness level is set up and the F command button does not help.

  Have you checked to make sure that the connections are secure?

  Has been recommended for your laptop replacement?

  Here is a link to a display size troubleshooting (Windows 8, Windows 7 and Windows Vista) which can also help.

  Here is a link to HP Pavilion dv6 Entertainment PC Maintenance and Service of Guide for your laptop.  Was the recommended replacement?  Please note Chapter 3, page 23, section 1, a list.

  Good luck!

• Re: L505 does not work after replacing the screen

  I had to replace the display screen on my Satellite L505 due to the 'accident '. After finding how to get instructions on the line, I was able to do the job, seemed ok, but it having moved up the screen on, but nothing else. When replacing at any time I felt an electric shock, so I do not think that the fried motherboard. He would have anyway? If this isn't the case, motherboard, would this inverter replacement needs. The accident was due to a piece of hardware that was sitting on the keyboard when my dog (the awkward beast) sat down on my satellite (I used it in his bed), the screen cracking. Help would be appreciated knowing what it could be.
  Thank you

  Hello

  I don't think that someone will help you in this forum. Who knows what happened... You must contact the Asp (SAV). Please, please understand me, it's hardware related problem that needs to be diagnosed by special service tools.

• Less Wifi reception after replacing the screen

  Hi, can someone tell me what might be wrong. After that I fell on my phone, I had replaced (RESTful) screen. Everything works fine, but the Wifi reception is worse then before. Contact RF cable problem? Or a smart Wifi (if aboard all) is able to do this?

  Anything else?

  Thank you!

  Hi @alfred52,

  It is difficult for us to determine what could be the reason for this, unless you get your phone looked to one of our authorized service center as uliwooly suggested.

• Blue screen in decline after replacing the screen

  I got my iPhone 6plus screen replaced at an apple store, earlier this week, and now a random regression a blue screen appears from the top of the screen and goes up and down, disappears, then pops up. Meanwhile, the screen is not sensitive to the touch, but when it stops and I double finger restart my phone several times, it works perfectly fine, then at random again. I've already set up another appointment on the apple store. What is an internal error and apple will charge me to fix this?

  It's either a problem with the screen replacement and Apple will not charge your for this or there is also damage to the logic board and you need to replace the entire phone. There will be an extra charge for this.

• My HP Pavilion DV6 will not start after replacing the screen

  I just replaced a cracked screen by following the instructions in the maintenance manual and now it does not start. The power light turns on and the fan works but nothing else happens. What can I do to trouble shoot this problem?

  The most common problem is the connection of the cable to the screen.  Make sure that it is tight. Check the connection to the motherboard as well, but it's usually OK.

• Laptop Dell XPS 13 L322X: 8 beeps start after replacing the screen

  Hi all

  I have laptop computer Dell XPS 13 L322X (serial number: CC2YVW1).  I use an external monitor because the screen is flickering with vertical lines and ghosts of the colors. I've updated the Bios and the driver video and tried the diagnostic mode (power and the D - key... and) without success.

  I just bought a new replacement compatible screen but the I cannot start using the new form and meeting the 8 beeps are heard. I tried to start with the external monitor and using power on the laptop with the D key, the new screen of the laptop began to switch colors four times and return the sound signal.

  I tried to disconnect the battery and the AC power and maintain the power to drain the left stored energy from capacitors without success.

  Thanks in advance for your help,

  Sala

  In this case, return the set of sieves of replacement - it's probably the cable is bad (but since it is an integral part of the screen, the set should be replaced.

• 3D Issue of the Qosmio F755 - 3d 350 after replacing the screen

  Hi, I had a problem with my Toshiba Qosmio F755 3D350 broken LCD screen and I have to replace it with a new screen.

  The new screen is the same model: B156HB01 V.0 of electronics AU, who had the original on my laptop screen.

  everything works fine resolution, the camera, but when it comes to 3D it doesn't have the Leds on the webcam is not turn on and activate the wiggle stereoscopy.
  How do I activate again the 3D or where is the problem?

  Thank you.

  Hello

  As far as I know after LCD (screen) or webcam or Exchange/replacement disassembly it s necessary to calibrate the LCD screen 3D sensor chip using special 3D calibration tool.

  This calibration can be performed by the Toshiba authorized service provider only!

  It seems that you have no choice to contact the ASP in your country to make this 3D calibration.

• Windows will not start after replacing the motherboard

  To begin, I must say that I am pretty clueless when it comes to computer skills.

  To summarize, I sent my CPU to a repair shop when my computer has stopped working. I removed my hard drive before starting the repairs because it contains confidential data.  They have narrowed the cause to a faulty motherboard and replaced by a new dissimilar.
  At the store, the guy had a vista 64 bit recovery disc so I have it home and tried to fix it. He said it will be a breeze and relatively bug free. As part of the Startup Repair, I tried to drive the Startup Repair, and tests were all successful except one. An error of diagnosis readings

  "Unspecified system configuration changes may have caused the problem.

  Repair action: repair and checking the integrity of system files

  Result: failed. Error code 0 x 490

  time taken = 720023 ms

  Everything I've done has led to a brief blue screen to the Windows loading screen and then it restarts itself.

  I also tried to restore to the previous two points, but it has also led to the square - a brief blue screen after the loading screen and restarts on its own windows. I'm not ready to reinstall vista and I can't afford to do it too, because I don't have enough disk space to perform another installation. Nor am I willing to reformat one of my two disks.

  If you need additional information on the specifications of the material that must be provided, ask me.

  IM at my end intelligence now, and I really hope to solve this problem.
  Thank you.
  Bryan M

  Hello

  I'm sorry, but you have to completely reinstall the operating system after replacing the motherboard with a different motherboard.

  "Startup Repair" is exactly that: a start NOT a repair system repairs

  What has happened, it is the operating system on your hard disk contains the drivers for the old motherboard and does not and you can't change drivers in doing what you do.

  The only way to solve this problem is to reinstall Vista.

  You wipe the hard drive and restart and make sure that the repair shop gave you the disc to install the new drivers of motherboard after you reinstall vista or download on the website of the manufacturer of the motherboard.

  And here a question for you to consider, too.

  If you bought a copy of Vista retail yourself, you can use the method above to a new installation and then install the new disk motherboard drivers.

  But, if your computer is a trademark of purchased manufacturer, HP, Toshiba, etc., you can not change the motherboard that the license of Vista OEM is stuck at motherboard the origin of the manufacturer that it has been installed on and now you canceled your Vista license.

  See you soon.

• HP Pavilion G6 - 2148TX Power Up after replacing the fan problem

  Hello

  After replacing the fan, I have a power issue with the laptop. Basically, the laptop will only fuel on the power cable disconnected to the motherboard. It is by mistake only after the fan has been replaced and everything got back together, I noticed that the battery was not charging.

  I then opened the machine and reconnected the power cable to the motherboard and nothing - no power.

  When connecting to the source of power with the battery in place, adjacent to the power supply lights in WHITE then remains ORANGE and will not. Seeing no other, no fan noise, nothing.

  If I remove the battery, the adjacent to the power supply led in WHITE and white rest however not feed either. Same agin, no LED, no fan noise, nothing.

  Now, I opened the machine upward and disconnected the power from the motherboard. Put it all back together and that the laptop starts as usual with the battery and it works very well. (Well until the battery runs in any case)

  I'm looking for some advice on what the issue could be given my conclusions.

  Thanks in advance.

  Well, I've now solved the problem. I bought the DC power cable that connects the motherboard to the socket on the laptop. $15 on eBay.

  Connecting the supply cable to the Jack of the laptop, the 'white' and is LED stayed on. The battery was not installed at the time. With a deep breath, I pressed the power button expecting anything to happen, but when he lit a big smile appeared on my face.

  The laptop booted up normally.

  I then install the battery and the battery indicator showed it to load. Everything is good and a son of 18 very happy. The fault was as expected according to my previous email. I hope this helps someone in the future, shame on HP response was off the mark in light of the original explanation and clarification post. But appreciated nonetheless.

• HP a1250n, radeon xpress 200 question after replacing the CPU, Standard VGA Graphics goes not down

  Recently, I messed up my CPU and bought a replacement (exact same kind). I am running windows 7 ultimate and for about 6 months prerequisites with no problems. After replacing the CPU I get intermittent lock ups, sometimes with a small portion of the screen flashes. I say intermittent but at least every 15-20 minutes. Different programs, different habits, but still the screen freezes.

  I went in and deleted the driver under graphics cards, pick a 'completely remove the option' - it after restarting the system on its own charged for a Standard VGA Graphics Adapter and since there is then no more accidents. Of course the functionality is not as complete, large icons and such, but it works.

  If it certainly seems to point to a driver conflict I think. But for this machine, is there ever any single Vista Windows 7 driver. My skills are not so, but I'm moving.

  Any guidance?

  Hello

  Yes, your PC has integrated graphics controller: ATI Radeon XPress 200, we don't find drivers compatible Windows 7 ATI.

  The BEST OPTION: Buy a video card, then insert it into slot PCI Express 16 on the motherboard to better display and multimedia performance with Windows 7 to a value using else, it looks just like Windows XP

• I have to reset the charge cycle counter after replacing the battery?

  I had a defective power adapter, running on the number of cycles of load on my battery.  Thus, it no longer accepts a charge.  I have been running only on AC for over a year now, but finally decided to replace the battery.  What are the steps to reset the counter after replacing the battery?

  Replce just the battery, the battery will communicate the number of cycles to the computer. No adjustment is necessary.