Broken power connector? Where to find one?

Similar Questions

• Satellite Pro L20 - broken hinge baseplate - where to find the parts?

  Hello

  First post here, so please excuse the lack of local etiquette.

  My son has a Toshiba Satellite Pro L20 with a broken hinge base plate. I'm calling it a base plate that I can not find the name of the part anywhere on the web so far.

  Its obviously the metal plate on the basis that the hinge attaches to.
  You can see it if you remove the battery.

  Nobody knows what is this part and where I could possibly buy one?

  Kind regards

  Jimmy

  Hello

  I think that in this case the ASP from Toshiba (certified partner) might help you.

  You must enter in contact of this ASP in your country and the technician should be able to order a compatible part for laptop.

  You will find here all the FSA all over the world:
  http://EU.computers.Toshiba-Europe.com-> supported downloads &-> find an authorized service provider

• HPPavilionN5412l notebook optical drive replacement, where to find one, and HPManual

  
  

  eBay is going to be your only choice at this point.

  http://www.eBay.com/ITM/refurb-HP-OmniBook-XE3-Pavilion-N5000-N5100-N5200-DVD-ROM-drive-F3925-69938-/350520265636?PT=US_CD_DVD_Blu_Ray_Drives&hash=item519ca2cba4

  The service manual is no longer available here. You can see on the ' net for the XH series, N5000 series and the Omnibook XE3 series, all are essentially the same machine. In my view, there is a screw on the bottom which can be removed to slide the optical drive.

• Satellite A30 151: motherboard power connector broken

  I have an old toshiba A30-151 that has fallen down a while a go because of the power connector snap into the power socket. This had happened before at the back of the power supply, but I managed to solder back together. Unfortunately it broke again and has so the PIN inside the socket.

  So after having managed to get into the nitty gritty of the laptop and have the motherboard out, I had a replacement for welded to the. Problem is there is a missing piece. I have a picture of this here:

  http://i150.Photobucket.com/albums/S83/Dalio1984/motherboard.jpg

  It was a picture of him before you put the Jack on. The chip missing normally goes where the right red circle is. Now I have not tested yet cause I have to go through the process of implementation of back together which is tomorrow nights work. I was wondering if it will work without it, if I can get a replacement part for this, or if I could figure out what it is (for example a resistor) replace it with a piece of stock to its equivalent.

  I realize this is probably a little extreme, but any help in this matter would be appreciated.

  Hello

  A figured out if this will work without this chip?

  I don t think that someone here in the forum will be able to give you an answer exactly.
  The drawing of the motherboard is necessary and that these documents are not easy to find because the manual are not:(pour usage public)

  So I hope you can find more information in internet

  Good luck

• Where to find an IP for hp psc 1410 printer all in one

  Hello.

  Anyone know where to find an ip address for hp psc 1410, printer all-in-one?

  Make sure you have the latest version of Adobe Flash installed.

  Adobe Flash

  Download the latest version of the software for your printer on the link below and save it to your desktop

  FTP://ftp.HP.com/pub/softlib/software10/COL11786/MP-35363-2/CDB-AmericasEuro1-Express_NB.exe

  Then download revo uninstaller on the link below and install it.

  http://www.revouninstaller.com/download-freeware-version.php

  Unplug the printer from the PC.

  Revo and see if he can find any installed printer HP software.  If so, right-click the icon of the software and choose uninstall.  During the process you may be asked to remove the registry entries.  If you are, just select and click on delete.  Do the same for any left over files and folders.  When finished, restart the PC.

  Disable any Antivirus and Antispyware software.

  Now, double-click the installer on your desktop to start the installation, the connection of the printer when you are asked.

  I hope this helps.

  Best wishes

  DP - K

• Workstation HP Z620 dual xeon: really only 1 6-pin power connector on the graphics card?

  Hello

  I have a question about the HP Z620 workstation.

  recently bought a dual xeon with 960 GTX installed on the 6-pin connector.

  as I can't find any other power to use nor on the power connector

  or nowhere on the set, I wonder how a graphics card must be powered only

  needs

  1 x 8-pin

  or

  1 x 8-pin + 6 pins

  or

  2 x 8 pin?

  I know there are some discussions about this in this forum, but I did not understand

  the solution. Some said there are adapters to go 6-pin to 8 pin (or 6pin to 2x8pin)?

  But how is that possible?

  like many, I know, 75 watts are max of the pci-e connection, 75 other watts Max for 1x6pin.

  so plug any adapter, 1x6pin for graphics cards that need much more power would be

  According to the standard / danger, right?

  and what about graphical installation double?

  would be happy if someone around could help me with this.

  best regards

  Chris

  The search box on this page by default search only this forum, and it is very convenient.  If you type "extra", you will find a lot of info.

  The Z620 has two of these 6-pin cable, and HP got creative and molded into two empty containers down to the black plastic fan holder before.  So, one is being used by you and the second is sitting there plugged and similar, it is used, but it is stored just it did nothing... the fan is powered differently.

  These extra HP 6 - pin PCIe power cables are not standard ATX... they are better.  The ATX standard is 75 watts can go up to the card out of the slot, and another 75 watts can come via the additional 6-pin cable.  HP 6-pin cable can do a bit more.

  This is the message that you want to read, and there there details that were not in any of the HP manuals that I searched through, but the answer was on the label of Z620 power supply.  12V 18A each, plus adding info on some special HP adapters that allow you to take a HP 6-pin and divided to two 6-pin connectors or cable HP 6-pin connector 8 pins.  Watch here.

  http://h30434.www3.HP.com/T5/business-PCs-workstations-and-point-of-sale-systems/HP-Z620-workstation-PCI-e-auxiliary-graphics-power/m-p/5651091#M12740

• Caddy optical Bay for Pavilion dv4 - 1228ca - where to find?

  Anyone know where to find less expensive optical Bay caddy for Pavilion dv4 - 1228 laptop computer ca?

  Try eBay, however, could not find one with the connector appropriate; This one

  http://www.newmodeus.com/shop/index.php?Main_Page=product_info&products_id=198

  would work, but it was a little overpriced for an investment of old machine... Any ideas, please?

  TIA

  Newmodeus is about the only game in town for this kind of product. I know an organization called jacobsparts.com in my hometown has some drive hard generic 2d optical Bay adapters, but they wouldn't look nearly as good as that of your machine.

• G6-2030SL: replacement power connector

  Hello world
  My problem is that my PC (G6-2030SL) does not load, but my charger works on my old Presario CQ60-103EL.
  I checked the number of spare parts for two power connectors, and they are different.
  Can I replace my with presario power connector?

  EDIT: G6-2030SL power supply connector spare parts part number: 682744-001

  Spare connector power CQ60-103EL part number: 496835-0001

  It will not fit. You must get a replacement like-kind

  http://www.eBay.com/ITM/HP-G6-2000-G7-2000-series-genuine-AC-DC-power-Jack-cable-682744-001-/121662974034?PT=LH_DefaultDomain_0&hash=item1c53ada852

  It's the CQ60 one. See how the length of the cable and the plug are different?

  http://www.eBay.com/ITM/496835-001-HP-G60-635D-Compaq-CQ60-420US-AC-DC-power-Jack-cable-harness-wire-/371341852260?PT=LH_DefaultDomain_0&hash=item5675b2fe64

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Where to find the lock of the Pixma MG6320 printer scanner?

  Hello... Where to find the lock of the Pixma MG6320 printer scanner?

  Hi set231,

  PIXMA MG6320 is not a scanner lock switch.  If you try to set the printer for transport, please follow these steps:

  1. turn the unit off.

  2. confirm that the POWER led is off, and unplug the machine.  Please do not unplug the machine while the POWER light is lit or blinking white, as this may cause a malfunction or damage to the machine, the machine impossible to print.

  3. remove the output paper support, and then close the paper output tray gently.  The output tray extension is retracted automatically when the paper output tray is closed.

  4. disconnect the printer from the computer and the machine cable, then connect the plug to the machine.

  5. use duct tape to secure all covers on the machine to keep them open during transport.  Then pack the machine in the plastic bag.  Fix the material of protection to the machine when the machine to pack in the box.

  It has not responded to your question or problem? Please call or write to us at one of the methods on the page contact us for further assistance.

• HP G620470CA: G62 - 470 CA do not load - power connector?

  I'm helping a friend with a laptop HP G62 - 470 CA.  It runs Windows 7Home Premium.

  I'm a geek of very experienced computer hardware, since 1968, but only opened about 10 modern laptops - always with the help of downloaded books.

  The laptop in question has only Wi - Fi networks, and I have only a Linux computer with a dial-up connection, so there is no way to connect the laptop directly to the internet from here.  And I can't view the videos.

  The problem with the power connector - a common, but I've read all morning and have not yet find an answer.  There seems to be some interactions between the power brick, power conenctor, battery and motherboard problems.

  Like many users, she found her power connector is intermittent, needing stirring so he could connect. As I had fixed the old laptop of his brother with a work of pig after it (soldered to the motherboard) power connector went wobbly, she asked me to look at.

  When she showed me the machine, the battery was too dead to allow start-up of the machine completely.  The charge LED is not come yet a moment, and there is no visible light on the power brick itself (I don't know if there should be any on this model).

  Put a meter outside the ring and the central axis, I found on 18.5V, positive pin, which looked good and is stable.  Biting moments and the cable has not changed anything.  It seemed that the power supply was the culprit.

  I got it home (where I only switched) and studied the issue for several days, download of HP service documents and discovered that HP had improved their design with a nest, wiring-harness-connected socket which is more shock-resistant and easy to replace.  I told her, and she has ordered a replacement of cylinders harness + listed the number of exact model; I installed it, in the process of learning how to work the little clips on the printed ribbons cables and using a printed diagram from the bottom of the computer to save all the small screws and clips, "with circles and arrows and a paragraph to describe."

  As both outlets had pinbacks resin-locked up, it was not possible to test connections.  A new differed from the former only by not having only not four tiny, rectangular holes around the hole of the central axis.  Food is not about to mate with these holes, and it lists a tension, so I wasn't expecting that to matter.  Maybe it was a feature for foreign cersions of the power brick, I thought.

  I plugged it in no light, but I left in it for awhile in case only the LED was not connected.  Start the machine (including ahd been unable to boot), fortunately, he started and showed 85% battery!  However, only, which is down with the time - there was no load, or at least no more.  I checked the voltage of the charger to see if it may have been damaged by an internal problem.  I found only 13, 75 - 14.01 volts from the outside of the ring to the central pin (positive)!

  Appearing to use a battery to try to light the LED of charging, I watched the cable brick and found that there are THREE sets of contact - the spindle, the outer ring and the ring INSIDE. Others showed:

  4.75 - 4, 85 volts from the inside of the ring to pivot (PIN positive)

  18.5 - 19 volts from the outside of the ring inside the ring (inside the positive)

  Whaa?  The 18.5 was what I expected, but it was between two rings and not between a ring and a PIN.

  And at this time, I noticed that from time to time, a blue (or white, I guess you'd call it) a DUCT on the connector turned on briefly, then turned red orange and outside.  Over time, it stayed white wheat longer, up to 8 seconds at a time, without showing any ability to charge the battery.

  Reading much more here and besides, I noticed that many others had similar problems involving all parts of four - battery, power brick cable, connector and motherboard.  I noticed the battery test can be found in the pages of support and pulled up to HP Support Assistant to test, but the reliable program planted at startup.  It was a version of 7.something.something, the support site said that later was 12.0, so I downloaded that.  However, I can't understand how to install it on the HP machine after it (on USB) transfer to the Linux machine, and the laptop cannot get Internet at home.

  WHAT can I DO to narrow down the problem?  If I know what voltages to which contacts, I can try to charging a battery nicad-multi, that would eliminate all the problems of power supply brick.

  The laptop battery carries a lot of numbers, but next to the 'made in china' legend is CQ42 HP-6.  A sticker says 112B213G6LA65D9CJ83, and another with a barcode PRTNHP234BK06312120141.

  That's a lot to read, I know, but I want to provide as much information as possible to help the members of the forum with kindness.  Again, the machine turns on, but fell to 18% of autonomy.

  Thank you all in advance!

  Thank you, Reo51st - that clears up a lot.  As you probably know, the diagram on the power brick shows the symbol for PIN and ring only (with pin posiitve).

  Since I posted this question yesterday, I have since set up a battery of 12 NiCd cells and jerry-rigged a connector with tin foil and a piece of cable insulation, and load worked.  Then I drove on Free geek, our very convenient source of Vancouver (and sink - they take your trash for reuse or recycling) of the old computer bits and $18 me have a new power brick.

  I therefore declare this thread SOLVED (by me), even if the info from Reo51st certainly would have made me more confident in the test so I saw him at the time.

• At the end of the creation of an e-mail account, that the program will ask a software password security device, I don't know what it is or where to find it.

  At the end of the creation of an e-mail account, that the program will ask a software password security device, I don't know what it is or where to find it. To my knowledge I don't have a 'software security device. I use Windows 7 on an IMac.

  Apparently, you have defined a master password at one point. The password protects passwords that Thunderbird remembered.
  You can reset the password. More information in this article.

  http://KB.mozillazine.org/Master_password

• Where to find the keyboard for my Satellite Pro U300 13F?

  I accidentally distroyed my keyboard with wine?

  Who can give me a hint where to buy a replacement keyboard or a secondary market?
  The type of my laptop is: U300 13F p/n PSU31E-00X012DU

  Your advice, please, keesl

  I always ordered the keyboards on eBay.
  Check if you can find one for your laptop model.

• Equium P300-190 and P300-16 t - where to find cases of HD 2nd slot

  Does anyone know where to find the case of hard drive to the right side, and eager to put another hard drive in the second slot, but the case has 5 plastic post and don't want to break them.

  Anyone use the second location for an additional hard drive?

  You should check if the laptop supports a 2nd HARD drive.
  The availability of 2nd HARD disk location does not mean that the laptop would support a 2nd HARD drive.
  You should remove the HARD drive cover in the 2nd and need to check if the location contains the connector to HARD drive.
  If this isn t available connector, you cannot use 2nd HARD drive

• Tungsten e2 how hard reset with broken power button

  I am getting rid of an old Tungsten e2 and need to reset to factory settings. However, the power button is broken and I can't find another way to do a hard reset without using the power button. Is there another way? Thank you

  Welcome to the HP support community!

  Someone wrote a program years ago this very dilemma!

  Go to the following page and download and run the program named "Hard Reset".

  http://palmpowerups.com/downloads.php?cat_id=2

  WyreNut

• Bad power connector

  Recently bought a Mac Mini 2014 opportunity. Did anyone notice that their power connector is loose? When I received it Thursday it popped so I really pushed and he seemed to be very tight. I shook so much that I could barely get out today. When I went to reconnect, I only close it partially in order to disconnect easier if necessary and you worry nothing break. Love the machine so far but it's just a minor annoyance.

  You will need to inspect the end of the cord that fits inside the power supply of the computer

  and compare it with a new power cord for damage. The socket inside the computer

  is another matter; What wrong with this hand, is a more difficult task.

  There is a fairly well documented process of access to food, as seen

  in the iFixit.com repair guides for computer model of Mac Mini 2014. I looked inside.

  • Mac Mini - repair Guide end of 2014 - iFixit:

  https://www.iFixit.com/device/Mac_Mini_Late_2014

  So if the power cord itself seems incorrect from a new replacement, then

  It may be wise to consider purchasing another cord of correct specification.

  My end of 2012 Mac Mini has a similar cord with a built-in power supply, it is not a

  You can do a lot. The guide repair above shows that is taking part of the diet.

  Or would be if you were to heal the problem here. I rarely move my Mini once

  It is in a position of work and power; If did not find a problem with it disconnected.

  In any case...

  Good luck & happy computing!