Broken screen, external display mode standby with Satellite A10 S203

Similar Questions

• Incredible trouble with two A10 S203 network!

  I had two Satellite A10-S203. This mobile are configured to operate on Microsoft network (wired network) with the working group. Have a different IP, name, MAC addresses, and same workgroup. To the network to work about 15 computers. When I connect to the network from one of them his works very well with the network. If I replace the previous book to second it's job well too. But when I connect both at the same time to the network I got hurt. One work, second cannot send pockets but can receive them. When this two laptops are connected to some other network computers sometimes hangs up.
  This portable work very well no but together do not work in the same network.
  I checked the configuration of these hundreds of times and it's ok they can see and browse the net when are linked separately. Thought is it net card MAC addresses conflict but it isn t.
  Can someone help me with this?

  Post edited by: TomaszE

  You are quite right TomaszE, very cryptic your problem!

  But what is the subnet mask of the network? Also identical on all machines?
  Have you tried to change the IPS of the two laptop, just intended to test?
  All are machine have static ip addresses, or runs a dhcp server in the system?
  What about firewalls installed? Some programs have a blacklist of ip addresses that are blocked permanently to do anything on the network.

  Please give me more information

  BR

• The country on Satellite A10 S203 modem settings

  Hello

  I have a Satellite A10 S203. I use my laptop for most in another country then my home country (Netherlands).
  I tried to connect to internet in Germany, and I couldn't change the country of the modem.

  Does anyone know so and so, how, to change the countrysetting of the modem of my A10 S203?

  GRTS Frank

  Hello

  Check this thread http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=2515&tstart=50 please

  If all goes well it will help you. If this isn't the case, please write again.

  Bye and good luck!

• Satellite A10 S203: the CPU fan does not work properly?

  I have toshiba satellite a10 s203 and the cpu fan does not work correctly. What can I do about it?

  Hi SACRIFICE them.

  Here are some possible solutions to this problem of fan.

  1. When you have installed a base installation of MS (not the Toshiba Recovery CD) you need to install the Toshiba Power Saver and others utilities from the CD tools & utilities. The energy saver is responsible for the control of the fan.

  2. If you have a recovery based OS, you can update the energy saver of http://eu.computers.toshiba-europe.com site Web Toshiba under Support & Downloads - Download Driver

  If please check this and an answer then follow the next step!

  CAMPino

• Satellite A10 S203: sound does not work - just enough

  Hello!

  To my satellite A10 S203 sound does not work, I updated my sound card and the bios but nodifferents. Nothing in the system that says that I have something wrong whith my sound is just enough. I tried speakers headphones and challenging systemsounds, mp3, Auidi direct works cd... nothing.

  Any tip?
  [email protected]

  First check the status of the sound card in Device Manager.
  If there is a yellow climbing brand then you should try to reinstall the driver. (first remove it and after reboot, install a new)

  Have you checked the volume setting and the site of laptop? Eventually he s a very simple idea, but believe me, I read many comments here in the forum and a lot of guys forget this option simply.

• Need drivers XP for Satellite A10 S203

  HI :)

  I have reinstall my Toshiba Satellite A10 S203. (Model number: PSA10E-018EZ-NO)
  Problems is that I can't find the drivers on the own Toshiba driver download page. (A10-S203 is not listed)

  I was hoping that someone had a link, or at least a list of the material used in my laptop, so I can find the drivers myself.

  Would be really appreciated. :)

  Search in the Archives of Satellite A10 PSA10E box

• Using Late 2009 Imac as external display for PC with display port 1.2

  Hi all

  Thanks for your time.  I searched for a definitive answer to this question before I go ahead and make a purchase.

  I have a Late 2009 Imac 27 ".  I would like to use it as an external monitor for my new PC, which is a graphics card EVGA GTX 970 with a displayport 1.2 output.  I'll be able to use a DisplayPort / mini displayport cable to connect to my Imac to use as an external monitor for my PC.

  The Imac doesn't have the speed I need for photo editing but I like the contrast and the size of the screen offers.

  Any input would be appreciated!

  Discover > use your iMac as a display with the target - Apple Support Display Mode

  

  The way I read the article, target Display Mode only supports the Mac iMac connection.

• Aspire V3 - 771G recovery loop/Broken Screen / external VGA screen

  The problem is 2 things:

  1: PC, now a loop in "Recovery mode/diagnose-pc.

  2: now, we cannot access BIOS because of the external display is VGA but if we close the lid, we'll see, only the "Recovery" loop... »

  My friend used his laptop with and the external HDMI display for a while.

  then he noticed he has more behaviors in addition to viruses, like: acting as his pirate.

  a person resumes his mouse and so on.

  So he decided to make his pc recovery and then we can operate in Mode external VGA,

  but not HDMI and more.

  Reason for no longer works in HDMI is because of Windows may have these drivers?

  (external mouse and a keyboard installed)

  Try to start the computer on F10 or fn + F10 or F2, (laptop keyboard) and then close the cover.

  Even on the external keyboard.

  In any case suggestion as to access the BIOS with an external VGA display.

  Or any other suggestions?

  Zenpotter

  Hi and thanks!

  Another friend took the computer, pulled out the SSD and installed on his computer and do a clean install and put back, then it worked like a charm!

  Thanks for the reply anyway!

• This external modem will work with Satellite L500-1XL, running Windows 7

  Hello

  When in Spain, I need to use the dialing up to the internet through Telefónica.
  I guess that the L500-1XL is not an internal modem?

  This external modem will work with the L500-1XL running Windows 7?

  Thank you very much in advance for your help.

  A

  Hello

  You re right Satellite L500 doesn t have an internal modem, so you need an external.

  I think you can buy every modem that is compatible with Vista. Alternative ask your favorite computer dealer or authorized service provider

  A friend got good experience with USRobotics 56K modem like this:
  [USRobotics 56K USB Faxmodem USR5637 | http://www.amazon.co.uk/USRobotics-56K-USB-Faxmodem-USR5637/dp/B0019LZCEI/ref=sr_1_1?ie=UTF8&s=electronics&qid=1269253039&sr = 8-1]

• What is the best external display for use with Tecra A8?

  It is perhaps off of a question, but I'm in the market for an external monitor for my Tecra A8. The price range of 400 euro round. Any suggestions?

  Hello

  What size of monitor you want bye? 17TO? or 19a?
  I read checked the product on some websites and the Samsung SyncMaster 970 19a testing? is not a bad choice. You should get to 400Euros.

  But it's usually? not easy to say which screen is best. I think you should visit some computer dealers and compare external displays. You know that you can check the clarity, brightness, contrast and response time. CA? It's important if you want to play games. It should support a low value. For example 8-6 ms

• Is the western digital 120 GB HDD compatible with Satellite 2450 S203 WD1200VE?

  My hard drive crashed on my laptop and now blue screen whenever I turn it on, when it tries to start. Finally it will start but then I can't turn off again without going through the same process.

  I tried to replace the original 40 GB hard drive model number MK4021GAS with another model of disk toshiba MK4026GAX to see he has an IDE #0 error on startup which I think means that it is not compatible, as it works in a caddy without any problem. So I would check the compatibility of a hard drive, I'm interested.

  I've been watching 120 GB WD1200VE drive and I was wondering if it's compatible? If someone could give me any assistance on this would be welcome!

  Thank you

  Hello

  The IDE #0 error because the HARD disk has been configured for the wrong master/slave/c-salt settings.
  Please check the position of the rider on your old HDD and set the same on the new one (MK4026GAX)
  Looking for a new 120 GB WD1200VE? Well, the Satellite 2450 S203 is a little bit older and I'm afraid the BIOS will not support this large size of disk HARD m.

  I would recommend so check the MK4026GAX settings before you buy a new HARD drive device.

• Satellite A10 s203: USB ports does not work

  Hello! All of a sudden my usb ports do not work on my satellite sa10-s203. Tried everything (even restarted the ashes of l-top nothing happened.) Enybody can help me? Kris...

  Hello

  If the USB ports are properly recognized in device then as Quad Manager said it could be an external problem. The USB port is 500mA power. If the external device requires more power to work in this case, it of necessary to use the external power supply.

  Good bye

• White screen when exit Mode standby - Satellite Pro A300-15 t

  We have a new laptop Satellite Pro A300-15 t (PSAJ1E00F00FG) with Windows Vista 32. Display of the laptop will not return to the standby mode. He remains in black color. I can see the Green HDD indicator.

  I have to shut down & restart power with force using power switch.

  Is it any Hotkeys to get out of sleep mode? We are pressing on button / stop or keys.

  If someone had similar situations & got some solutions, please help...

  Thanks in advance...

  Hello

  As far as I know that these issues are resolved with BIOS update. Can you please tell us which model of laptop you have exactly and what BIOS version is preinstalled on your laptop?

  I think 2.70 is the latest version of the BIOS.

• Black screen and mode standby with the message "no signal".

  Correctly, it's... kind of weird, I use my computer and the monitor for a year or 2 now and don't never had real problems. The thing is that when I got home last night I found my black screen and standby mode (as if the computer was turned off (which it wasn't)). I thought that the reset will solve the problem, and so I did and didn't get the message "no signal". All tried, reconnecting cables, reset several times I could count... nothing helped for awhile.

  At any given time during one of my restarts it reworked all of a sudden no aparent reason. So going on my daily buissiness I want to get back in the saddle, when I accidentally hit the side of my computer with a book and the screen went to 'no signal' again. Just tried again and even used my cell phone to check if the monitor was working,... now comes the weird part,... also on my laptor monitor is having problems with "no signal", but only when I do my main screen. It works as a secondary screen, but I can't get the context in which to work. (finding that I'm guessing that this problem is not related to my normal computer, but I'm not sure).

  I am running vista and got a nvidia 8800GT graphics card. Also, I noticed something that is at any time using both the hdmi cable on the graphics card or using the socket with the internal chipset of my computer makes no difference. in both cases, I get "no signal" and the screen goes to sleep... Is there someone who can help me and tell me what probably is the problem here? I'm really looking forward to the answers, thank you very much for your time and effort.

  Hi Ron Suykerbuyk,

  If you are comfortable, then try to remove the CPU cover and check if the graphics card is well connected to the motherboard. Even if it is connected correctly, you can try to reconnect the graphics card and check.

  Hope this information is useful.

• How to bypass the login screen of the mode standby in Windows 7 Professional with active screen saver

  Here is the solution/answer:

  1. go in Control Panel

  2. click on "personalization."

  3. on the lower right corner to say 'screen saver '. Click on screen saver.

  4. in the scree of Eve window between the 'Screensaver' name and the power management box is empty 'Wait' then 'minutes '.

  Right of "minutes" is a block that says "on resume, display the login page.»

  5. If the "On Resume, the logon screen" box is check uncheck.

  6. click 'OK' your done

  This works if you have an active screen saver and works.

  Hello

  Good thing Mark a. Kite!

  Anyone having this problem should also consult:

  Control Panel - Power Options - left requires a password on Wake-Up - tick don't
  Require a password - save the changes.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">