Bug to stop random, DIFFERENT from the power switch question
I found a problem that I have yet to isolate the cause of the, but his is happened a few times now. Sometimes, when my Sansa has updated its database and has not played a song at the moment, if I change the settings and then try to play a song, it starts to play, then cut completely. It doesn't happen often, but these are the circumstances each time. The player will not respond and will refuse to power on. The only way to get on is to hold the power switch until the device resets, release, and then power it turned on, which of course means another data refresh. Once this is done, my settings are all back to where they were before the last change, I can change their return, and everything works fine. As I said, the problem don't occur often, only about 3 times since I've had (since June), but its still an obvious problem. If someone wants to know more about it, or want me to try a few things, let me know. I'm mainly just let Sandisk people know, then maybe we can get this in a future firmware update.
New firmware is in the release process now, so hang on until release us the next version. It can help about this. Should be within 1-2 weeks.
Tags: SanDisk Sansa
Similar Questions
-
The new App Store for El Capitan update has locked up my macbook pro. Reboot got about 3/4 fact and the machine stops. Turned off the power and turn it on again for nothing doesn't. How in my machine to begin troubleshooting?
The problem is most likely an attempt to update a system malfunction prior it is probably a problem with your computer, not the El Capitan.
Start by:
Reset the PRAM and NVRAM on your Mac.
MacIntel: Reset of the controller (SMC) system management
Start in Safe Mode , and then re - start normally. It's slower that a normal start, so be patient.
If you are unable to start;
Reinstall El Capitan without erasing the drive
Please make sure that you back up.
- Restart the computer. Immediately after that the chime hold down the command and R until the Utility Menu appears.
- Select disk utility, then click on the continue button.
- Select the withdrawal (usually Macintosh HD) entry of the volume in the list aside.
- Click first aid icon in the toolbar. Wait until the button is active, then click it.
- Quit disk utility and re-enter the Utility Menu.
- Select Reinstall OS X and click on the continue button.
Also, see this tip for user: basic steps for the OS X upgrade.
If this doesn't get you;
Install Yosemite or El Capitan, from scratch
Backup if possible before proceeding.
Restart the computer. Immediately after the chime hold down the command and R buttons until the Apple logo appears. When the Utility Menu appears:
Select utility disc in the Menu Utility, then click the continue button.
When loading disk utility, select the volume (entered into withdrawal, usually Macintosh HD) from the list of devices.
Click Delete in the main window of disk utility. A panel will fall.
Define the type of Format Mac OS extended (journaled).
Click on the apply button, then wait for the done button to activate and click on it.
Quit disk utility and re-enter the Utility Menu.
Select reinstall OS X and click on the continue button.
-
Cross reference marker text differs from the text on the page
The text for a cross-reference marker is different from the written text of the page. For example, I have a numbered heading written as "3.1 Cats and Dogs", but the text of cross-reference to this position marker is "55227: title 1: 2.1 pigs and horses." The cross reference looks and works great on the page, but I can't understand why the text of the marker is different, and why it cannot be updated to match the text on the page.
I use Windows XP and FM9. Thanks in advance.
Ron,
The target of a cross-reference marker must have a unique string that differentiates it from any other marker of cross-reference in the file... it is how Frame numbers how when it comes so it can maintain the link and make updates. As you have probably guessed, this string is a concatenation of way random (I think) integer to format BMP target and target the text of TFP at the time of the creation of the xref. With all these settings, it is easy to achieve the goal of a single string.
It seems appropriate to have this text update during an update of the xref, if something changes in the target. However, this would create two problems:
-All xrefs that are not being updated at the time wherever the marker is published would be broken. For example, suppose you have xrefs folder has a target and make updates, which modifies the marker of target due to changes to the target. Any xrefs in file B (or any file for that matter) would become broken, because they are still configured to search for the previous string of marker.
-An update of the xref always you would have to save the changes to the target file, which is an inconvenience at best. For example, if you have made an update of the book and xref target markers have been changed, you'd have to make sure that the files associated with the changes were saved later, otherwise your xrefs update would be broken later.
So, in summary, the text of the marker is just a unique identifier that is defined during the creation of the xref and necessarily must stay the same for its useful life, unless you want to go around fixing broken xref all the time. Moral of the story... do not put swearing or slandering of boss in your topics like temporary jokes if you never create xrefs their
Russ
-
Buffer the output AO, refresh rate is different from the sample clock frequency
Hello
I am an AO output in the buffer using a single channel. I have a stamp with a ripple of 200000 points with a triangular waves of a 1000pts each repeated 200 times. If I want a frequency of 1 Hz, I simply update this waveform 1000pts and if I wanted to 5 Hz, then 5000pts and so on. But there is some frequency that I won't be able to use like the refresh rate (the number of samples that I ask to update) is different from the sample clock frequency, which makes synchronization with the other difficult to trigger (incomplete cycle). Frequency 3 Hz (update 3000pts), as (update 7000pts) 7, 6 Hz (update 6000pts), 9 (update 9000pts)... 11Hz at 15 Hz and is not valid in the sense that the refresh rate is different from the sample clock frequency. That makes a whole lot of inaccessible CONFIGURED! Can someone tell me what determines the banned frequency? Is this something to do with the material?
concerning
One thing you can try is to change the number of samples per cycle. This cannot give the precise frequency accurately, but can reduce the average error.
120 Hz, the error is currently about 400 parts per million (ppm). The accuracy of the time base is 50 ppm, then this error is less than 10 times the inherent error due to the time base.
Consider this configuration: the closest nominal sampling you rate, you can get is 120048 Hz (1000 samples per cycle at 120 Hz). If your buffer contains 1200 samples per cycle, 100 copies of it would produce 1 second of data to 120,048 Hz. But if the buffer contained an average of 1200,48 useful Samper by cycle, you get the exact frequency. Of course getting 0.48 of a sample is delicate. But the kind of feasible. If you use 48 cycles in the 1201 samples per cycle and the cycles of 52 to 1,200 samples per cycle, the total number of samples per second = 120048. Average frequency will be exactly what you want. Instantly, the frequency is slightly higher or lower than the exact value. By an alternation of 1200, 1201, 1200, 1201... 1201, 1200 100 cycles that the Jig is fast. If you group all 1200s whole and all 1201 s frequency hopping may be more sensitive. If this kind of jitter is acceptable depends strongly on what you do with the release.
This technique is used in some systems of frequency synthesizer.
Lynn
-
KB952155 Setup Error.
While trying to upgrade to remote desktop I get the following error message: Setup cannot update your Windows XP files because the language installed on your system is different from the update language. Now, that - what it means and how can I fix it? I have installed SP3Eivind Aakhus Hello,
If you have the latest version of Office installed on your computer remotely, then you need to enable the Active X control.
Follow these steps to activate the ActiveX module.
a. open Internet Explorer by clicking the Start button, and then click Internet Explorer.
b. click Tools, point to manage add-ons and then click Enable or disable add-ons.
c. in the list view, click to view all ActiveX, ActiveX controls downloaded controls.
d. choose the one you want to activate, and then select Enable.
-
Installing Win AP Automation! 3.0 to accelerate VB Express 2010.
Warning message:
Update for MS Wim (KB971513) Setup error
Setup cannot update your Windows XP files because the language installed on your system is different from the update language.
My XP language is Norwegian. The rest of my 'stuff' MS is English.
- What you have already tried to solve the problem
Hello
I suggest you to check the article mentioned below.
Error message: Setup cannot update your Windows XP files
http://support.Microsoft.com/kb/555042
I suggest to select the language appropriate to the download page and check if you are able to install the update on the system or not. The update that you are trying to install on the system must be of the same language as installed.
Thanks and regards.
Thahaseena M
Microsoft Answers Support Engineer.
Visit ourMicrosoft answers feedback Forum and let us know what you think. -
Hello Sir
customers start the dhcp service, I get an account of 1079 ACE ' the error specified for this service is different from the account specified for other services in the Sun in the same process.
Go to start / all programs / accessories / Run. Type netsh winsock reset catalog , and enter. You may need to restart. See if that fixes the problem.
I hope this helps.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
Original title: the account specified for this service is different from the account specified for other services running in the same process
while trying to connect to internet, I get the message "connection status: unknown the account specified for this service is different from the account specified for other services running in the same process" that you start happens out of the blue. When I run the diagnostic and repair tool it says that Windows cannot resolve the problem, contact admin or your ISP. I know that my internet service works very well. I am currently on an e-machine running Windows Vista Edition Home Premium and it connects without problems. My problem is that my most recent top of office (gateway also on Windows Vista Home Premium) receives connection problems. IM connected to the internet (DSL) with the ethernet cable from the Yukon. All the lights are green on the wireless gateway, so I know that the service is very good. Strange thing I noticed, when I go to network status and share and view Gateway desktop computer shows the "Yukon Ethernet controller" as the connection while the e-machine device says Im using "Intel (R) PRO/100VE Network Connection" Im using the same cable (Yukon) and put in place for both computers, so I was wondering what that was all too. Any help is appreciated.
Hello
Thank you for writing to Microsoft Communities. From your problem description, I understand that you can not connect to Internet.
1. have there been recent changes to the computer before the show?
2. the problem occurs in safe mode with networking?
Please go ahead and follow the steps mentioned and later a update on the State of the question.
Method 1: Wi - Fi and in Windows network connection issues:
Additional information:
The problems of Internet connection:
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problemsPlease follow these recommended steps and post if you still experience the problem.
-
Original title: How can I restore my services to the default state.
Here is the error message when I try to start it manually to the top of some service programs.
"Windows cannot start the Diagnostic Policy on Local computer service."
"Error 1079: the account specified for the service is different from the specified account.
for other services running in the same process. »
Hi raospent,
1. have you made any hardware changes or software on the computer before this problem?
2. what services you try to start?
You can follow this link & check if it helps.
Hope the helps of information.
Please post back and we do know. -
Original title: I'm trying to start the Windows Firewall.
I'm trying to start Windows Firewall services, (administrative control / tools/services/windowsfirewall Panel) and error 1079: the account specified for this service is different from the account specified for other services running in the same process, rises. What should I do?
Hello
· You will remember to do recent changes on the computer before this problem?
· Logged in as an administrator on the computer?
I suggest you follow the steps mentioned below:
Method 1:
Follow the steps described in the following link and check if the problem persists:
http://support.Microsoft.com/kb/2478117
Method 2:
If the previous step fails, run the System File Checker tool to troubleshoot missing or corrupted, system files proceed to the following link:
http://support.Microsoft.com/kb/929833
Method 3:
If the previous step fails, set the center of security and its dependencies services to run under the Local Service account. Follow these steps:
a. Click Start, type services.msc and press to enter.
b. double-click Security Center, click on tab log.
c. Select "this account", click on the Browse button, type Local Service and click ok.
Type the password and confirm the password and click ok.
-
Hello, I'm Michael.
I'm a guy who lives in Hong Kong, I bought a laptop that comes with Chinese traditional x 64 Windows 7 Home Preium. I want to use this laptop as a computer professional. Because I don't want to use Chinese as my default language in my computer, so I'm going to upgrade my computer I have subscribed the TechNet, so I downloaded an iso file from the Microsoft TechNet Web site. I downloaded an English x 64 to windows 7 Ultimate. I hope it would work, but an error message is skipped during the upgrade. It is said: you can do an upgrade using an installation disc that's different from the language installed on your computer. Go online to see how to install Windows 7 and keep your files and settings.I tried to press the hyperlink (go online) and it does not at all. I have to ask this question to the Microsoft Answers and see if if anyone can give come me advice because I do not want to click on the custom button because there are some files saved in my computer. So I need answers as soon as possible because I could die without a PC! Thanks for all those who read this and you time.No direct path to the evolution of the Chinese language to English. But you can upgrade your version of Home Premium to Windows 7 Ultimate (upgrade Express). Ultimate has support for English and a number of other languages.
=================================================
If you have a retail version of Windows 7, then use the "Anytime Upgrade":
When you use the "Anytime Upgrade" option, all what you need to do is enter the product Windows 7 upgrade key has been purchased. Do this by clicking on: start/search and enter: upgrade ExpressUpward to a more powerful edition
http://www.Microsoft.com/Windows/Windows-7/get/anytime-upgrade/Home-Premium.aspxUpgrade to another edition of Windows 7 by using Windows Anytime Upgrade
http://Windows.Microsoft.com/en-us/Windows7/upgrade-to-another-edition-of-Windows-7-by-using-Windows-Anytime-UpgradeA 'step by step' to go through an upgrade to a lower edition of Windows 7 to a higher edition of Windows 7:
http://windowsteamblog.com/blogs/Windows7/pages/the-Windows-Anytime-Upgrade-experience-for-Windows-7.aspxPaths to upgrade Windows 7 (supported upgrade scenarios)
http://TechNet.Microsoft.com/en-us/library/dd772579%28WS.10%29.aspxWindows Anytime Upgrade is supported only in the following countries:
Australia, Belgium, Canada, France, Germany, Italy, Japan, Netherlands,
Spain, Sweden, Switzerland, United Kingdom and United StatesWindows 7 Starter to Professional upgrade Express
http://www.Microsoft.com/Windows/buy/Windows-7-upgrade-Starter-to-professional.aspxMost likely the best option and the most popular will be the Home Premium upgrade to Windows 7 Professional, which includes Windows XP Mode. The extra $50.00 for Windows 7 Ultimate will only give you two additional features, bitlocker (for security) and the ability to switch between any of 35 languages.
Windows 7 - Anytime Upgrade - frequently asked Questions:
http://Windows.Microsoft.com/en-us/Windows7/Windows-Anytime-Upgrade-frequently-asked-questionsWindows 7 - upgrade Express features:
http://Windows.Microsoft.com/en-us/Windows7/products/features/Windows-Anytime-UpgradeWindows 7 - version comparisons:
http://Windows.Microsoft.com/en-us/Windows7/products/compare-editionsMS Windows 7 store price:
http://www.microsoftstore.com/Store?defaultKeyword=Search&siteid=msstore&action=list&CategoryID=38336300&Keywords=Anytime+Upgrade&result=Note: Retail 'Full' or 'Upgrade' product keys will work when you use the Express Upgrade feature.
The Express Upgrade "may" not always work for users who have system integrators and or OEM product keys, this applies also to VL (Volume License), MSDNAA or key teaching will not work with the Express upgrade. KMS users consult your administrator before attempting to perform an Express upgrade.J W Stuart: http://www.pagestart.com
-
File Explorer has stopped working properly from the taskbar
File Explorer has stopped working properly from the taskbar. Currently, I get only 3 windows on taskbar & opening No. 1 opens no.2 & vice versa, but no. 3 opens on its own. Can someone explain this & find a cure?
I would like to highlight the file Explorer icon and pin it again. To do this.
(1) close all running programs, including records from the file Explorer
(2) right click on the icon on the task bar Explorer and "Unpin from Taskbar" to remove
3) press Windows + R to display the race. Type C: and press OK. This will open your C: drive.
(4) make a right click on the taskbar that appears, the file Explorer icon, and then click "Code Pin to Taskbar" to pin it.
-
Then the specified mail server host name differs from the certificate CN
My BIEE installation is 11.1.1.7 and SMTP server configured in EM. I put the root CA for SSL certificate file.
He calls the error message "then hostname specified mail server differs from the certificate CN", when agent is running.
The SMTP certificate common name is "pop.mydomain.com", and the hostname of the SMTP protocol is "SMTP.mondomaine.com". If the names are different, it works fine with Outlook and other email clients.
All the solutions to fix it?
You are right. For the security certificate should be identical to the host. But the smtp server is not placed under the responsibility of us. I modified the file hosts as a workaround. I can't find any biee configuration option to ignore the incompatibility.
-
Sales order form, line status code is displayed as "WITHDRAWN". but the same code appears as "AWAITING_SHIPPING" for the same line in the database.
Where the value in the frontend is filling?
It differs from the flow_status_code in oe_order_lines_all?
Thanks for the correction.
He slipped right out of my mind!
Here is a detailed explanation of this case:
Status of orders picked and picked partial
Kind regards
Bashar
-
Necessary to define the database time zone differs from the OS
We have a database of who currently resides in New York. Let's move to another server that resides in London. This is a problem, because each date which is currently in the time base is New York time, but after the move, all the new data that created time will always be time to London. We do not want users to have to remind any date preceding the date of move, will idle 5 hours if we would like to do is to have the database always on time in New York despite the BONE being London time. The server will be shared with other applications for the operating system time zone will have to remain with London time. The database will only have data for our application. So is there a setting of database that we can use to set the time zone database is different from the operating system time zone? The database is currently 10 GB but is promoted as part of the move to 11 g.
What is the data type of the column? If the date or timestamp, then there is no time zone stored with the data. If timestamp with time zone, then the time zone of the data remains the same regardless of the time zone database and operating systems.
SQL> select dbtimezone from dual; DBTIME ------ -05:00 SQL> alter database set time_zone='EST'; Database altered.
Maybe you are looking for
-
icon dock or desktop for specific combinations of library/itunes
My wife and I have different iTunes libraries on our iMac, but I'm looking for an easier way to switch between libraries to Option - < click iTunes > and then search for the library on the right. I prefer to create a script (shell, terminal command l
-
How my emergency phone call work
How my emergency phone call work
-
Hello I want to change my security questions, but I don't get any link reset in my rescue email security issues
-
Drivers (Asio?) Center Audio/USB multimedia Hub
Hello I'm looking for drivers for Multimedia Center Audio/USB Hub and for the Asio drivers for it. I can't find! Can you help me? Hector.
-
HP Pavilion p157sa 15: 15-p157sa HP Pavilion in Windows 7 function keys
I installed Windows 7 Professional 64 bit on my HP Pavilion p157sa 15. I think all is now well, except the brightness keys FN (to decrease F2 and F3 to increase brightness) do not work. I installed the drivers as in my previous post (URL at the end o