Button Mode Catalyst 2960

Hello

Can someone tell me a method of turning off the function of the Mode button on a catalyst 2960 to stop this reboot of the switch after being detained for 10 seconds? Even with a config full on the switch, the function "reset" always seems to bypass the config and clear/reload the switch.

Is it possible to disable this feature in the software?

Thank you very much

Charlie Read

Try the following command: no express installation

See the following link for more details on the order.

http://www.Cisco.com/en/us/products/hw/switches/ps628/products_command_reference_chapter09186a00801a6c4a.html#3549999

I hope this helps.

Steve

Tags: Cisco Security

Similar Questions

  • Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

    Hi Experts,

    I have some confusion with the button Mode with cisco 2960/3560 switches.

    I read on many forums and articles, but where things are not clear.

    a place given 3 seconds and somewhere is given 7 or 10 seconds.

    Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

    A. password recovery (according to my knowledge 3 sec) good or bad?

    Configuration of the switch (start + run) would be safe

    After the recovery of password? Yes or no

    B. factory default (according to my knowledge 10 dry) good or bad?

    I'm afraid, because if I press mode button more than 3 seconds, then

    It will delete any configuration of cisco switch. Yes or no

    Qus2) I want to recover the catalyst 2960/3560 switch password without

    Start/run configuration to lose. That is my main concern.

    Please tell me how to do this, what will be the time keeping Mode buttom

    in a few seconds?

    Qus3) which means this line

    "If the password recovery mechanism is disabled in switch

    then you will lose all the config.

    This sentence has been given on this forum url

    https://supportforums.Cisco.com/thread/140848

    KS

    Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

    Use the following terminal settings:

    • Bits per second (baud): 9600

    • Data bits: 8

    • Parity: None

    • Stop bits: 1

    • Flow control: Xon/Xoff

    Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

    Unplug the power cable.

    The power switch and take it to the switch: command prompt:

    2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

    Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

    2960, 2970 Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.
    3560, 3750 Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

    The system was interrupted before the flash at the end file system initialization

    loading the operating system software:

    flash_init

    load_helper

    boot

    switch:

    Run the flash_init command.

    switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

    Run the load_helper command.

    switch: load_helper switch:

    Question the dir flash: command.

    Note: Be sure to type a colon ":" after the dir flash.

    Appears in the file system of the switch:

    switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

    Type rename flash: flash: config.old config.text to rename the configuration file.

    switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

    Issue the boot command to boot the system.

    switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

    Enter "n" at the prompt to abort the initial configuration dialog box.

    --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

    At the switch prompt, type en to enter a mode.

    Switch>en Switch#

    Password recovery

    Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

    Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

    Copy the configuration file in the memory.

    Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

    The configuration file is now reloaded.

    Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

    Note: Replace passwords that are required. You must crush not all passwords listed.

    Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

    Write the running configuration in the configuration file with the write memory command.

    Sw1#write memory Building configuration... [OK] Sw1#

    For factory reset:

    do not give under the control of factory reset

    Switch#copy flash:config.text system:running-config

    can I copy the running configuration to Flash

    Switch flash running-config #copy:

    Destination file name [running-config]?

    Building configuration...

    [OK]

    Switch #copy running-config startup-config

    Name of destination file [startup-config]?

    Building configuration...

    [OK]

    Review the link for more information below

    http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

    Please note the useful messages.

    Concerning
    Vesta
    "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

  • Cisco Catalyst 2960-S switch configured for 802. 1 x sends a query to access the Radius Server Radius

    Setup

    Cisco Catalyst 2960-S running 15.0.2 - SE8

    Under Centos freeRadius 6.4 RADIUS server

    Client (supplicant) running Windows 7

    When Windows client is connected to the port (port 12 in my setup) with authentication of 802. 1 x active switch, show of Wireshark that catalyst sends ask EAP and the client responds with EAP response. But it made not the request to the Radius server. The RADIUS test utility 'aaa RADIUS testuser password new-code test group' works.
    Here is my config running. Any advice would be greatly appreciated.
    #show running mySwitch-
    mySwitch #show running-config
    Building configuration...

    Current configuration: 2094 bytes
    !
    version 12.2
    no service button
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    no password encryption service
    !
    hostname myswitch
    !
    boot-start-marker
    boot-end-marker
    !
    activate the password secret 5 $1$ Z1z6$ kqvVYRQdVRZ0h8aDTV5DR0 enable password!
    !
    !
    AAA new-model
    !
    !
    AAA dot1x group group radius aaa accounting dot1x default start-stop radius authentication group!
    !
    !
    AAA - the id of the joint session
    1 supply ws-c2960s-24ts-l switch
    !
    !
    !
    !
    !
    control-dot1x system-auth
    pvst spanning-tree mode
    spanning tree extend id-system
    !
    !
    !
    !
    internal allocation policy of VLAN no ascendant interface FastEthernet0 no stop ip address!
    GigabitEthernet1/0/1 interface
    !
    interface GigabitEthernet1/0/2
    !
    interface GigabitEthernet1/0/3
    !
    interface GigabitEthernet1/0/4
    !
    interface GigabitEthernet1/0/5
    !
    interface GigabitEthernet1/0/6
    !
    interface GigabitEthernet1/0/7
    !
    interface GigabitEthernet1/0/8
    !
    interface GigabitEthernet1/0/9
    !
    interface GigabitEthernet1/0/10
    !
    interface GigabitEthernet1/0/11
    !
    interface GigabitEthernet1/0/12
    switchport mode access
    Auto control of the port of authentication
    dot1x EAP authenticator
    !
    interface GigabitEthernet1/0/13
    !
    interface GigabitEthernet1/0/14
    !
    interface GigabitEthernet1/0/15
    !
    interface GigabitEthernet1/0/16
    !
    interface GigabitEthernet1/0/17
    !
    interface GigabitEthernet1/0/18
    !
    interface GigabitEthernet1/0/19
    !
    interface GigabitEthernet1/0/20
    !
    interface GigabitEthernet1/0/21
    !
    interface GigabitEthernet1/0/22
    !
    interface GigabitEthernet1/0/23
    !
    interface GigabitEthernet1/0/24
    !
    interface GigabitEthernet1/0/25
    !
    interface GigabitEthernet1/0/26
    !
    interface GigabitEthernet1/0/27
    !
    interface GigabitEthernet1/0/28
    !
    interface Vlan1
    IP 10.1.2.12 255.255.255.0
    !
    IP http server
    IP http secure server
    activate the IP sla response alerts
    recording of debug trap
    10.1.2.1 host connection tcp port 514 RADIUS-server host 10.1.2.1 transport auth-port 1812 acct-port 1646 timeout 3 retransmit testing123 key 3.
    Line con 0
    line vty 0 4
    password password
    line vty 5 15
    password password
    !
    end

    interface GigabitEthernet1/0/16
    !
    interface GigabitEthernet1/0/17
    !
    interface GigabitEthernet1/0/18
    !
    interface GigabitEthernet1/0/19
    !
    interface GigabitEthernet1/0/20

    Have you run wireshark on the server because the request to switch? If so you make sure that there is a response from the server? For Windows network POLICY Server (I've never tried Centos), you must ensure that the request is related to a policy which then authenticates, or denies access. Usually, it is a matter of such attributes and the seller.

    Regarding the configuration, it seems a bit out of the AAA. Try to remove the:

    line "aaa dot1x group service radius authentication" and this by using instead:

    "aaa dot1x default radius authentication group". After the dot1x word you are supposed to provide a list of the authentication or the default Word if you do not want to use a list.

  • Dot1x multidomain on Catalyst 2960

    Hello

    I improved my 2960 with the latest basic version of LAN 12.2 (46) which includes the authentication of domain Multi (MDA) and I tried to configure what is described here:

    http://www.Cisco.com/en/us/Tech/tk389/tk814/technologies_configuration_example09186a00808abf2d.shtml

    I have the following exceptions in my configuration:

    (1) SE - cat 2960 with the latest version of IOS 12.2 (46) that supports the MDA;

    (2) using the Win2K IAS as a server radius. and

    (3) third party (Avaya) with active begging dot1x IP phone. I have a PC with ability to dot1x connected to the second port of the IP phone.

    That's what I set up on the phone IP port:

    interface FastEthernet0/9

    switchport access vlan 221

    switchport mode access

    switchport voice vlan 222

    dot1x EAP authenticator

    self control-port dot1x

    multi-domain host-mode dot1x

    protect the dot1x violation-mode

    dot1x reauth-deadline 30

    dot1x re-authentication

    spanning tree portfast

    I also configured the server Radius IAS Win2K to send RADIUS 'cisco-av-pair attribute' tell the authenticator (Cisco Catalyst 2960) that a supplicant (IP phone) is authorized on the voice VLAN as described in config-notes above link.

    When the supplicant IP phone starts to authenticate, he succeeds, but that the port does not allow the field of VOICE, even though the 2960 receives the attribute "cisco-av-pair" of the Radius Server RADIUS. I confirmed the reception of this attribute of debugging on the switch.

    RADIUS: Receipt of id 160.2.100.74:1645 1645/64, Access-Accept, len

    110

    17:02:38: RADIUS: authenticator 7 d AC 50 FE 14 B4 FC DC - 3A A4 E5 3F 1E 76 62

    C3

    17:02:38: RADIUS: EAP-Message [79] 6

    17:02:38: RADIUS: 03 05 00 04

    17:02:38: RADIUS: [25] in class 32

    17:02:38: RADIUS: 44 05 05 A2 00 00 01 37 00 01 A0 02 64 4A C9 01 1 33 79 52

    D8 58 00 00 00 00 00 00 1 b E7 [D7dJ3yRX]

    17:02:38: RADIUS: seller, Cisco [26] 34

    17:02:38: RAY: Cisco-AVpair [1] 28 'device-traffic-class = voice.

    17:02:38: RADIUS: Message-Authenticato [80] 18

    17:02:38: RADIUS: D9 42 78 88 26 5A 65 83 68 B0 E0 C7 AF 5TH 0F 51 [B

    [x & Zeh ^ Q]

    17:02:38: RADIUS (00000009): receipt of id 1645/64

    17:02:38: RADIUS/DECODE: EAP-Message fragments, 4, total 4 bytes

    Cat2960 #show dot1x int fa0/9 details

    Dot1x FastEthernet0/9 information

    -----------------------------------

    EAP AUTHENTICATOR =

    PortControl = AUTO

    ControlDirection = both

    HostMode = MULTI_DOMAIN

    Violation mode = PROTECT

    A re-authentication = on

    QuietPeriod = 60

    ServerTimeout = 0

    SuppTimeout = 30

    ReAuthPeriod = 30 (configured locally)

    ReAuthMax = 2

    MaxReq = 2

    TxPeriod = 30

    RateLimitPeriod = 0

    Dot1x authenticator customer list

    -------------------------------

    Domain = DATA

    "Supplicant" = 0004.0d9b.46d8

    AUTH State = AUTHENTICATED SM

    AUTH BEND State IDLE = SM

    Port status = AUTHORIZED

    ReAuthPeriod = 30

    ReAuthAction = is re-authenticated

    TimeToNextReauth = 20

    Authentication method = Dot1x

    Authorized by = authentication server

    Policy of VLAN = n/a

    I don't think I need CDP to allow the field of voice, if the Radius server sends the attribute "cisco-av-pair".

    Have I misunderstood the concept?

    Thank you!

    You can share the config switch?

    Missing for example aaa authorization network default radius group?

  • The Catalyst 2960 G switch configuration

    Is it possible to configure a Catalyst 2960 G Switch to act as / be an unmanaged (no router) switch?  If so, please provide detailed and simple instructions.

    Hi @lcbalogh1,

    I think that these switches are not routing compatible, but one thing... What you want to do is to have the switch set in a single broadcast domain (all ports in the same VLAN), right? If so, follow these steps:

    • Disable the routing features with the configuration command global "don'tno ip Routing.
    • If the first command is not accepted, type the "No dsm prefer lanbase-routing.

    These two steps above to disable the routing features.

    OK, to mark all the ports of the members of the same VLAN, you have a few options:

    • You can leave all the default ports VLAN (VLAN 1)
    • Or, you can configure all ports in another VLAN different
      • switchport mode access
      • access switchport vlan id - vlan>

    Hope this is useful for you.

    Rgrds,

    Martin, computer scientist

  • 6248 FI Cisco's UCS with Cisco catalyst 2960 connectivity

    In our environment, UCS, connects the two fabric as a Cisco Nexus 9 k switch upstream with vPC and it works well. But we need to isolate some virtual servers on the blades of the UCS on an entirely separate DMZ switch which is Cisco catalyst 2960.

    (1) so can we connect cables separate physical twinax of FI uplink ports to catalyst 2960 and connectivity to the servers in the DMZ keeping YEW to nexus connectivity as it is?

    (2) in this case, as there are 2 switches to nexus core 1 and 2 so we will require 2 cisco catalyst 2960 for disjoint such a network? or otherwise we can connect A FI and FI B to one on his 2 numbers 2960 switch. Gig SFP ports + 10?

    (3) also suggest things must be taken in charge, the best guides practice or an illustration in this context.

    The assignment is static and cannot be changed.

    location 1 - uplink 1

    slot 2 - uplink 2...

    If a property has no blade, the corresponding uplink is not used and that can not be changed!

    This dedication of uplinks of IOM is of course a lot of resources: cables, ports on FI, allowed port,...

  • Web authentication Catalyst 2960

    Hello

    I am trying to configure Web authentication relief on a catalyst 2960 switch. The goal is to authenticate customers via web authentication that are consistent (the part of 802. 1 x works fine) not 802. 1 x and allow them access to the network. The problem is that the web authentication seems to fail.

    The equipment about my question: switch catalyst 2960 (version: 122 - 37.SE) and a FreeRadius.

    Here's what happens:

    The authentication window will appear in my browser and the access request is sent to the RADIUS.

    The term RADIUS replies with an Access-Accept. Debugging running on the switch show that all this information is coming properly authentication and switch outputs debug a 'status = PASS' and permission to debug outputs a 'status = PASS_ADD'. Despite this the browser on the client generates a message "authentication failure".

    I have read the manual and the Cisco attribute value pairs are mentioned: ' priv-lvl = 15' and «proxyacl...»» ». They are required to make it work? Given that I'm not setting up any authentication switch connection via RADIUS.

    Any suggestions?

    Thanks in advance

    Yes, they are mandatory.

    If priv-lvl = 15 is not returned to the switch, the user will see? Authentication failed? and the access list will not apply. If the source in the statements of proxyacl field is not? everything? or there are other errors of syntax, the user will see? Successful authentication? but the access list will not apply and the user will be denied access to the network.

    Not sure about the configuration of specific FreeRADIUS, but you need to set up the? [026\009\001] Cisco av pair VSA. It should look like:

    Priv-lvl = 15

    proxyacl #10 = ip permit a whole

    Let me know if this lets you squared

  • Aironet 1252 with catalyst 2960-8TC-L & 1841 router compatibility

    Hello

    First of all they are togther a good combination?

    I'll buy new ap 1252 and switch catalyst 2960-8TC-L my question can I connect the access point to 1 x 10/100/1000Base-T/SFP (mini-GBIC) (uplink) port?

    because to work on ap with capacity 300 Mbps, it needs port 1000, I will use to power ap powerinjector.

    It will be 15 sereve pc as a working group and 60 customers on wlan.

    Concerning

    Saher

    Depending on the type of traffic and bandwidth customer requirements demand, you might need a couple more of ap which means you may have to settle for a switch of 24 ports. Cisco recommends 15-25 users by so, but still, you can have more if it's just e-mail and web browsing.

  • How acess catalyst 2960-s

    How acess catalyst 2960-s

    The main method of management is the Cisco Network Assistant however if you need to use the console port, then use the supplied RJ45 to DB9 cable to connect to a local serial port.

    Software wise, that it is possible to extract the 2 files HyperTerminal from a CD in Windows XP to run on a Win7 PC. The best alternative is a PuTTY terminal emulator.

  • not visible on the switch Catalyst 2960 vNIC...

    Dear all,

    I configured the UCS chassis with 5 blades and installed the esxi on all five blades...

    I created a VNIC 10 per server and by now I have ip for esxi management by combining two NICs for and YEW is connected to the switch catalyst 2960. The uplinks are 1 Gig at the END and at the end of the switch... and I made these trunk at the end of the switch, all permitted the VLAN on the trunk link

    I have configured all the VLANS on during vNIC based on a model and all of those selected. vlan1 is the vlan by default & selected the same.

    Please help me to solve the problem... I got tired of all the means & could not able to find a solution.

    Kind regards

    Gopi G

    Greetings.

    Please confirm you learn your esxi mgmt addresses (VMK0 will inherit mac vnic UCSM) on FI: #connect nxos

    #See table of mac addresses

    Do the same on your 2960 switches.  You see the mac addresses on the ports of 2960 connected for the UCSM uplinks?

    Your uplinks UCSM go the 2960 into a port channel?

    Thank you

    Kirk

  • Menu bar is not visible, but it is button mode full-screen. How can I fix it?

    While I'm in Firefox, it seems that I am mode full screen, as my menu bar is missing in the application, but when I looked at how to troubleshoot, it told me to click the mode button full screen (with diagonal arrows) but is not visible anywhere in my browser. If not, how can I exit full screen mode? Thank you!

    You get the menu bar if you close this window of Firefox?

    On Mac, you can't hide the menu bar as in Windows and Linux, and because the operating system control the menu bar then it may not be a Firefox problem.

    You can try:

    You can also try to remove the Firefox plist file.

    See how the .plist files becomes corrupt and troubleshooting results

    Come on in "library > Preferences" and remove the plist for Firefox (org.mozilla.firefox.plist).

  • Touchpad button mode on Linux

    Hello. How to activate the touchpad mode 'button' on a Linux operating system? (Ubuntu 13.04, specifically)

    I don't speak of the possibility to tap on the 'switch' on the touchpad button, then the volume control bar or the six other top icons ([here's one [image | http://aps2.toshiba-tro.de/kb0/HTD9702NL0000R0105182.png] related configuration in Windows operating system]).

    Even the ability to simply configure custom areas tap would be useful. Is there a way to define them?

    Note: this should work on a Toshiba Satellite A200 too.

    Thank you, have a good time.

    Hello

    Some useful information in the Wiki of the Ark: link: https://wiki.archlinux.org/index.php/Touchpad_Synaptics

    There is even a document man describing the possible parameters for the binary file: link: http://linux.die.net/man/5/synaptics

    The Ubuntu documentation may also be useful: link: https://help.ubuntu.com/community/SynapticsTouchpad

    Hope this helps

    Tom BR

  • M30 - buttons Mode Front and control Audio and video do not work

    Hello

    Front Mode and Audio/video control buttons do not work

    Any ideas?

    Thank you

    Hello

    As far as I know the Toshiba utility controls is responsible for the use of the key.
    Have you tried to install Toshiba controls?
    See the page of the Toshiba driver for this driver.

    Good bye

  • Put in command button Mode loses the callback function

    NOR expensive.

    I have a code I want to change the buttons toggle robot (according to different scenarios). However, if I put the command Mode of the button disabling at VAL_INDICATOR or VAL_NORMAL for this button, the callback function ceases to be called when the button is pressed.

    What is the defined behavior?

    I use 8.0.1 (356) CVI

    Kind regards

    Brian

    Yep, the VAL_HOT did the trick.

    A big thanks to dsappet and jr_2005 for taking the time to investigate this.

    Much appreciated!

    Kind regards

    Brian

  • Comments-vlan; Catalyst 2960

    Hello

    I would like to set up a guest - vlan and vlan restricted on a switch 2960, but I can't.

    The version of IOS (hollow obtained: see version) is:

    SW Version SW Image model switch ports
    ------ ----- -----              ----------            ----------
    * 1 52 WS-C2960S-48 I/S-L 12.2 (53) SE2 C2960S-UNIVERSALK9-M

    I am configuring the interface using the following commands:

    RAK-ASW01 #configurer
    Configuration of terminal, memory, or network [terminal]?
    Enter configuration commands, one per line.  End with CNTL/Z.
    RAK-ASW01 (config) #interface gigabitEthernet 0/1/11
    Access to RAK-ASW01(config-if) #switchport mode
    Self control-port RAK-ASW01(config-if) #dot1x
    RAK-ASW01(config-if) #dot1x comments - vlan 17
    RAK-ASW01(config-if) #end

    the result is the following, as if the comments - vlan only is not supported:

    RAK-ASW01 #show dot1x interface gigabitEthernet 0/1/11
    Dot1x Info GigabitEthernet1/0/11
    -----------------------------------
    EAP AUTHENTICATOR =
    PortControl = AUTO
    ControlDirection = both
    HostMode = SINGLE_HOST
    QuietPeriod = 60
    ServerTimeout = 0
    SuppTimeout = 30
    ReAuthMax = 2
    MaxReq = 2
    TxPeriod = 30

    RAK-ASW01 #.

    similar result is trying to set up a local network virtual auth failure.

    the full configuration file is attached.

    Many thanks in advance,

    Wawan972_

    Hello

    You see it here. It is expected if you use this command.

    How to see he uses 'show interface running x/x' and see if configuration commands are there, or if there is already a device on the port if you use the command 'show the interface of the x/x authentication session' and see if the vlan comments is used or not.

    HTH,
    Tiago

    --

    If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

Maybe you are looking for

  • IP5 front panel

    I have an I Phone 5 The façade seems to be projecting out of the side at the top In my view, the question in relation to a battery bulge I need a press takes the Home button and some presses repeat time

  • Mail crashes immediately when opened

    Mail on iPhone 6 and iPad opens for 1 second, then quits? But Mail on iMac still works fine.

  • Slow speed connection complete

    Hello! I got a really weird with my wireless speed as seen above, Im using a Broadcom 4313 on my Probook 6555 b and a Netgear WNDR3700 router W. Is there a limitation of speed for some reason any on the broadcom wireless card? Changing channels make

  • SCXI1125 calibration

    Hello I need to calibrate a SCXI1125 using NOR-DAQmxC module in a (MFC) application in VC ++. I understand that I need to use the 'DAQmxAdjust1125Cal' and 'DAQmxInitExtCal', but I do not understand the method. Do you have an example of code to perfor

  • HP compac Win XP Pro Drivers nx6110 laptop-

    Anyone know where I can download the above mentioned enternet controller driver? Thank you