C4580 - error when setting up connect through WiFi w / Time Capsule

I used my C4580 to print and scann with wireless in the past, a Netgear WiFi router with a DLink WiFi router.  I recently started using a Time Capsule from Apple as my WiFi router.  I have two active groups, so I have a 2.4 GHz signal and a 5 GHz signal available for my wireless products to connect to.  All the other products I use (a MacBook Pro running OS X Lion, an iMac running OS X Lion, a CPU HP running Windows XP, a CPU Dell running Windows 7, a Fujitsu laptop running Windows Vista, Apple TV, an iPhone, and an HTC Evo a TiVo set - top box) are able to connect to one or the other of these signals of network without problem.

Here's what's happening with the C4580:

1. I plug my C4580 on my MacBook Pro via USB.

2. I open the HP installation wizard.

3. in the first part of the "Setup" section, I select my "Photosmart C4500 series", which shows as connected via 'USB '.

4. in the second part of the topic "Setup", I check the box "configure yoru device to a wireless network.

5. in the third part of the "Setup" section, my 5 GHz network is not displayed.  My 2.4 GHz network appears, by dint of complete signal, showing the encryption 'WPA_PSK' and 'Infrastructure' mode  I select this option.

6. After about two minutes, during which the Setup Wizard probably tries to connect the C4580 to the WiFi network, I get the following error message: "* device not connected * to configure the network settings for the selected device, please temporarily connect it via the USB port.  The device can be disconnected from the USB once the network settings are transferred. »

Note: Throughout this process, my C4500 WAS connected to my MacBook Pro via USB.

Question: What other steps should I take to solve this problem?

Thanks for your time.

First time that I posted on a forum techy, bt I get a lot of help from them, then it's time to spread the love.

In any case, I was struck by our similar problems were, we have exactly the same set up and the same current. I've been hitting my head against a brick wall for a whole afternoon. Your temporary solution lead me to a very simple implementation and a more permanent solution.

Your normal home network have an apostrophe or special characters, such as YourName Wi - Fi network?

I had two networks put in place (already had a network of comments) called W - Fi Latitude and comments Latitude travel network travel network.

On your advice I tried to use my Gust netowrk. Oddly, when he showed up on the list, it lacked the apostrophe (the other network was not missing the apostrophe). When I tried to click on it, it said that there was not. I tried to type the name in its entirety in the box 'Other networks' and I was able to connect, but the software insisted that even if the printer is now connected, the MacBook was not (even though it was clearly).

The anomaly has led me to believe that the HP Softare along with apostrophes, I went to the airport and renamed the two networks with apostrophes. I gave the private network a go, and voila, everything went well.

It is a lesson in how to make a long story short. Basically, to remove the apostrophes in your network name in the airport and then try again.

Tags: HP Printers

Similar Questions

  • When my Macbook connect to WIFI my normal PC to the internet cut

    First off sorry for my bad English, but as say the title "when my Macbook connect to WIFI my normal PC to cup of the internet.

    I was playing online games (WoW) on my normal PC I opened my macbook to work with her, and then I saw that I was disconnected from my game online so I test a few times and the problem is that whenever my macbook is connect to my Wifi my router send... my PC internet is disconnected (my PC is using cable connect to the router)

    Thanks in adv

    That would be a problem with the way you have the router or computers configured for wifi. It could be that they are all both use the same ip address. Usually, when configuring a router you begin by setting up a computer with cloning the mac address of the computer to the router and then the other set up. If you do not have a mac address on one of your computers, it's the problem.

  • oracle.jbo.DMLException: Houston-26061: error when opening JDBC connection.

    Hi, I use JDev 11.1.1.7.0

    I got this error when I try to run the module of the application. Please help.

    I use the JDBC data source in the configuration of application modules, set the connection of business components.

    [1498] an exception has occurred when ordering.

    [1499] oracle.jbo.DMLException: Houston-26061: error when opening JDBC connection.

    at oracle.jbo.server.URLConnectionHelper.getConnection(URLConnectionHelper.java:218)

    at oracle.jbo.server.URLConnectionHelper.getConnection(URLConnectionHelper.java:45)

    at oracle.jbo.server.ConnectionPoolDataSource.getConnection(ConnectionPoolDataSource.java:72)

    at oracle.jbo.server.ConnectionPoolDataSource.getConnection(ConnectionPoolDataSource.java:61)

    at oracle.jbo.server.DBTransactionImpl.establishNewConnection(DBTransactionImpl.java:1004)

    at oracle.jbo.server.DBTransactionImpl.initTransaction(DBTransactionImpl.java:1185)

    at oracle.jbo.server.DBTransactionImpl.initTxn(DBTransactionImpl.java:6837)

    at oracle.jbo.server.DBTransactionImpl2.connectToDataSource(DBTransactionImpl2.java:304)

    at oracle.jbo.server.DBTransactionImpl2.connectToDataSource(DBTransactionImpl2.java:335)

    at oracle.jbo.common.ampool.DefaultConnectionStrategy.connect(DefaultConnectionStrategy.java:203)

    at oracle.jbo.server.ApplicationPoolMessageHandler.doPoolConnect(ApplicationPoolMessageHandler.java:620)

    at oracle.jbo.server.ApplicationPoolMessageHandler.doPoolMessage(ApplicationPoolMessageHandler.java:425)

    at oracle.jbo.server.ApplicationModuleImpl.doPoolMessage(ApplicationModuleImpl.java:9316)

    at oracle.jbo.common.ampool.ApplicationPoolImpl.sendPoolMessage(ApplicationPoolImpl.java:4530)

    at oracle.jbo.common.ampool.ApplicationPoolImpl.prepareApplicationModule(ApplicationPoolImpl.java:2460)

    at oracle.jbo.common.ampool.ApplicationPoolImpl.doCheckout(ApplicationPoolImpl.java:2270)

    at oracle.jbo.common.ampool.ApplicationPoolImpl.useApplicationModule(ApplicationPoolImpl.java:3169)

    at oracle.jbo.common.ampool.SessionCookieImpl.useApplicationModule(SessionCookieImpl.java:592)

    at oracle.jbo.common.ampool.SessionCookieImpl.useApplicationModule(SessionCookieImpl.java:525)

    at oracle.jbo.common.ampool.SessionCookieImpl.useApplicationModule(SessionCookieImpl.java:520)

    at oracle.adf.model.bc4j.DCJboDataControl.initializeApplicationModule(DCJboDataControl.java:523)

    at oracle.adf.model.bc4j.DCJboDataControl.getApplicationModule(DCJboDataControl.java:869)

    at oracle.jbo.jbotester.binding.TesterBinding.getConnectionInfo(TesterBinding.java:214)

    at oracle.jbo.jbotester.MainFrame.initializeDataControl(MainFrame.java:936)

    at oracle.jbo.jbotester.MainFrame.loadConfiguration(MainFrame.java:637)

    at oracle.jbo.jbotester.MainFrame.processArgs(MainFrame.java:602)

    at oracle.jbo.jbotester.MainFrame.main(MainFrame.java:433)

    Try using the JDBC URL instead of JDBC data source to run AppModule or run the application locally of JDeveloper. But if you will deploy the application on stand-alone weblogic, you use the JDBC data source and enter the name of the data source that is defined in weblogic

  • Error when setting the parameters on the tool

    Hi experts,

    I want to use ODIsqlunload, but it still gives the error. My win7 OS

    error:

    oracle.odi.oditools.OdiToolInvalidParameterException: error when setting the parameters on the tool
    at com.sunopsis.dwg.function.SnpsFunctionBase.getCoreOdiTool(SnpsFunctionBase.java:620)
    at com.sunopsis.dwg.function.SnpsFunctionBase.getSunopsisApi(SnpsFunctionBase.java:494)
    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.executeOdiCommand(SnpSessTaskSql.java:1415)
    at oracle.odi.runtime.agent.execution.cmd.OdiCommandExecutor.execute(OdiCommandExecutor.java:32)
    at oracle.odi.runtime.agent.execution.cmd.OdiCommandExecutor.execute(OdiCommandExecutor.java:1)
    at oracle.odi.runtime.agent.execution.TaskExecutionHandler.handleTask(TaskExecutionHandler.java:50)
    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.processTask(SnpSessTaskSql.java:2906)
    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java:2609)
    at com.sunopsis.dwg.dbobj.SnpSessStep.treatAttachedTasks(SnpSessStep.java:540)
    at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java:453)
    at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:1740)
    to oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor$ 2.doAction(StartSessRequestProcessor.java:338)
    at oracle.odi.core.persistence.dwgobject.DwgObjectTemplate.execute(DwgObjectTemplate.java:214)
    at oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor.doProcessStartSessTask(StartSessRequestProcessor.java:272)
    to oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor.access$ 0 (StartSessRequestProcessor.java:263)
    to oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor$ StartSessTask.doExecute (StartSessRequestProcessor.java:822)
    at oracle.odi.runtime.agent.processor.task.AgentTask.execute(AgentTask.java:123)
    to oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor$ 2.run(DefaultAgentTaskExecutor.java:83)
    at java.lang.Thread.run(Thread.java:662)
    Caused by: java.lang.Exception: ODI-30044: invalid parameter:-file
    at com.sunopsis.dwg.function.SnpsFunctionBase.actionSetParameters(SnpsFunctionBase.java:251)
    at com.sunopsis.dwg.function.SnpsFunctionBase.setParameters(SnpsFunctionBase.java:799)
    at com.sunopsis.dwg.function.SnpsFunctionBase.getCoreOdiTool(SnpsFunctionBase.java:616)
    ... 18 more

    and the code is:

    "SnpsSqlUnload «-file=F:\temp/data_6001_1001.dat" "-driver oracle.jdbc.OracleDriver =" «-URL=jdbc:oracle:thin:@musty-Pc:1521:XE "-user = system-pass = < @= snpRef.getInfo ("SRC_ENCODED_PASS") @ > - file_format variable = - charset_encoding = UTF8 '-row_sep = \n" "-date_format = YYYY-MM-DD '-fetch_size = 1000 '-field_sep = #
    Select / * + * /.

    columns...
    table...
    where (1 = 1)

    I have try this - settings file:

    F:\data_6001_1001.dat
    F:\test.txt
    C:\Test\test.txt
    C:/data_6001_1001.dat
    C:\test/data_6001_1001.txt
    c:/test/data_6001_1001.txt
    C:\test/data_6001_1001.dat

    all of them same result :(

    Please help me experts :(

    Hi experts, I have solved my problem :))

    my code like this:

    "SnpsSqlUnload «-file=F:\temp/data_6001_1001.dat" "-driver oracle.jdbc.OracleDriver =" «-URL=jdbc:oracle:thin:@musty-Pc:1521:XE "- user = system-pass =<@=snpRef.getInfo("SRC_ENCODED_PASS") @=""> - file_format variable = - charset_encoding = UTF - 8 '-row_sep = \n" "-date_format = YYYY-MM-DD '-fetch_size = 1000 '-field_sep = #
    Select / * + * /.

    But it's really strange! I change only the file--> FILE and driver---> DRIVER and row_sep--> ROW_SEP and etc...

    I don't know why, but they should be higher. I did on linux OS 64 bit and no mistake.
    But win7 it gave me error.

    I thik it's a bug...

  • Error search server old name of sharing of time capsule

    I recently had to replace my Time Capsule and by creating a new, I used a slightly different name for the share where the time capsule will be back up my macbook.  Now, I get an error popup to the effect of "Server"XXXXX Time Capsule"server not found  Maybe it's because the server is unavailable or... "Well, it is not available because I have a new time Capsule and I am using a different name for the backup share.

    Can someone help me so that this pop up goes and the computer will stop looking for part of the defunct time capsule?

    Did you remove the old path in the preferences of Time Machine that instructs your Mac where your old Time Capsule?

    If you do not, then the Mac will continue to seek a Time Capsule that does not exist and the report that he can't find it.

    Open Time Machine preferences

    Click Add or remove disks

    Select the old Time Capsule disk. under backup disks... that could be called data, unless you have changed the name

    Click on remove the disc

    Restart your Mac and recheck things.

    IF you have not changed the name of the new Time Capsule data, then you will see two drives two named data.  In this case, remove the two data disks.

    Then, the old time Capsule's power off, restart your Mac and set up Time Machine again by choosing the new Time Capsule disk.

  • new Express connects properly to the Time Capsule, takes both in offline mode

    I bought an Airport Express to extend the network of my time capsule wireless (2014). Introduction following the instructions as shown in the extend a network , it connects then after seconds seems to knock the time Capsule out of the network Express drops off the power, then the two, this happening again.

    I looked online and when a successful network is established a dotted line indicating a wireless connection appears under the time capsule, on mine utility Aiport is implementing a continuous line next to the time Capsule. Hope this has meaning and any help is greatly appreciated.

    In general you're doing something wrong... for example... you have ethernet connected between the TC and the Express... and then extend it by wireless... that will do exactly what you live... extend a network can be in wireless or ethernet... What are you doing?

    IF in wireless then no ethernet connection...

    If by ethernet then you do not extend... you create a network name parameters and security wireless...

    All this is supposed to happen automatically but frankly the magic went out on Mavericks and now it's just hard work.

  • Internet goes when you are connected to wifi

    Bought an iMac on eBay this week, works fine apart from a problem I encounter with internet stall, which really starts to get boring!

    It's an iMac, mid-2011, with OS X el Capitan 10.11.3 installed and put to update to the most recent update.

    The question...

    When you are connected to our home network (Sky Broadband) I get internet access for 5 minutes for an hour then stop him internet but the wifi is connected. At this point if I check all other computers/phones/tablets on the network that they are all still connected to the internet with absolutely no problem.

    The temporary solution...

    If I disable the wifi on my iMac and then back on again once it reconnects immediately and internet works fine still a time - until it stops!

    What I tried...

    Restart the mac repeatedly

    Restarted the router again

    In network settings, advanced on the mac, I renewed the DHCP lease (loads of times - note it always seems to come back with exactly the same ip address - I guess it's good?), updated the DNS (last post I read said to use 2.4.4.2 so am currently on that), tried to manually set the MTU to 1453, I deleted all the other networks stored outside my home network Too much.

    Does anyone have any suggestions please for all messages that have worked for them, or things that I could try?

    Thanks a lot for your help

    Joe

    Did you erase the internal drive and install OS X yourself? Did you run the hardware test? If this isn't the case, please do both.

  • Can not share the internet connection through Wifi

    Hi all

    I am connected to the internet using an external antenna connected via USB to my mac (WIRELESS n 801.11). I want to share this connection since my mac with other devices, i.e. my iPhone. I use the internet connection through system preferences--> sharing--> sharing internet--> connection on the part of wlan to computers via WIFI and give a name and a password for the wifi settings. When I start the connection icon wifi on the the high watch the arrow menu to the top, but it gives an IP address from 169 auto... etc etc and I can't any traffic to my iPhone.

    I tried to configure IPv4 to use DHCP with a manual (instead of automatic DHCP) address and IP I enter the IP address used in the WiFi, wifi says that it is connected to the name of the internet connection in the shared connection, I opened but once again no traffic to the iPhone. Also tried disabling the firewall, once again nothing.

    I run El Capitan 10.11.2.

    Clues?

    OS X El Capitan: share your Internet connection

  • "Security error" when setting 'Microsoft Exchange Hosted Services' Exchange account (user in company)

    I am a user in a company with a very large company that actually uses Microsoft Hosted Exchange services hosted by Microsoft employees in their facilities.  I called Palm support and they were clueless and zero help.  The lady pointed me to some Palm article I had already read and only remotely had nothing to do with my problem.  I don't see anything about this error message in the forums and google searches. Sprint has even replaced my other reasons palm pre, and the same error occurs once I configured the exchange account. I also see the error when I set up my account on my pixi nine wives. Our pre and pixi have already exchange accounts set up with success on our phones that are hosted by sherweb. Sherweb's exchange accounts work fine. I tried to set up this account of microsoft hosted exchange 5 - 6 times with the same result. He accepts my configuration information and adds to the list of email accounts available in the meadow. However, it keeps popping up the message stating "error of security policy:"Exchange..." Tap for details"(with a yellow exclamation point). Then he said "Security policy error" the Exchange (first part of my email address) account is disabled because it is impossible to define security policies. "'Leave this option disabled' or 'delete account '. I know that something does not work because it applied a policy of password or PIN on my phone which is not necessary, unless the account has been added. I can also see it in the "Mobile devices" section of outlook web when I login. This is the place in web outlook where you can see the last time the device synchronized, if remote, you can wipe the phone etc. If anyone has an idea how to solve my problem please post. Any ideas? I'm fresh out of ideas on this issue and very frustrated by the Palm developers. Just another example of evil-development and practical tests by Palm. I hope they correct this problem on later versions, but I'm only slightly optimistic that they will never get this medium of exchange e-mail at the level necessary for the support of large corporations. What I know is that my Microsoft Hosted Exchange account works fine on a Windows Mobile phone and an iPhone 3GS (confirmed by the other coworks who have set up their phones using our Exchange services). Accordingly, I have no choice but Palm to blame for this problem instead of Microsoft. Please, Palm fully support microsoft exchange e-mail users!

    After a lot of research on the subject, here is my point of view on the State of support for MS Exchange @ Palm and other companies.

    Unfortunately, Palm Pre and Pixi, WebOS is not fully supported Microsoft Exchange.  This has led to numerous reports of frustrated customers and countless hours of time wasted by consumers and technical support trying to figure out how to connect these Palm devices to the MS Exchange e-mail servers.  Way to go Palm!  Provide support for all the free email accounts worldwide and decide not to develop a product that is able to support your most rich and more influential-based email clients.  These are the people who are most likely able to spend more money on your mobile products or make decisions for companies that are able to buy huge amounts of smart phones.  Way to go guys!  Penny wise and dollar foolish if you ask me!  Palm supports only partially a handful of MS Exchange security policies.  They document what they take in charge, but they do a very poor job of documenting or even explain the limitations of the software.  Their States of documentation that the security policies that are not supported will not be applied and that users will still be able to connect to the exchange server.  This is certainly not true based on the reported error and other similar user reports.  Here is how iPhone and Palm compare in regards to the support of MS exchange security policy.  Notice in the quotes below the iPhone supports the policy of 'require the encryption of devices' which is very probably used by your greater and more security conscious companies or Government institutions.  I'm sure that Palm's inability to support "device encryption" is why I get this error, even if I have really no way to prove it at the present time.  Come on Palm, if you go to support full POP3 and IMAP, you must provide the full support of the binding protocol and political security by Microsoft Exchange product.  Here is the comparison between iPhone and Palm WebOS:

    ' Said the site of Apple, the iPhone supports the camera allow, password enabled, allow a Simple password, alphanumeric password, Password Expiration, history of password, Maximum password attempts failed, minimum password length, maximum idle lock, policy, Minimum refresh interval complex character devices. ", require manual synchronization while roaming and - in iPhone OS 3.1 only - require Device Encryption". (13 security policies)

    "Palm Web site says its WebOS 1.1 and later support active password, alphanumeric password, password history, Maximum password attempts failed, maximum length password, lock of inactivity maximum, Minimum peripheral characters complex and Password Recovery." (8 security policies)

     

    Windows Mobile 6.1 supports all THE policies.

    BlackBerry does not support the EAS (MS Exchange)

    Google's Android is not compatible EAS (they may have recently released some support but not full)

    Conclusion: If you want a mobile device that fully supports MS Exchange, buy something that is running Windows Mobile 6.1 (or higher) or even an iPhone 3 g (or more).  At least, until Palm decides they want to throw a development more $$ to support Microsoft Exchange E-mail to enhance their level of support.

    Reference: "how to avoid the lie of the foreign exchange policy by smartphone' http://www.infoworld.com/d/mobilize/how-avoid-smartphone-exchange-policy-lie-004?page=0, 1

    Message edited by morgan1112 on 12/01/2010 15:00
  • BlackBerry Smartphones using the BBM after connecting through wifi?

    I just arrived in canada and I have connected my torch to wifi wpa personal, the browser works well but my bbm is not working, can someone please tell what to do to plug on bbm?

    Thank you

    Fankoosh wrote:

    No I don't have an international plan, but I had my sim card on until it got to with the fact that bbm does not work on wifi

    Yep, that will definitely throw a crimp in your BIS data connection.

    How can you not have noted that early?

    • Put the SIM card in and start the backup.
    • Leave the appliance to connect again with your network, roaming.
    • Then you should be able to go to your Mobile network settings and to disable the connection to your mobile phone network and to use BBM and email, etc., through WiFi only.
  • Internal server error when trying to connect Facebook to Toshiba Places

    I'm looking for help with a problem I've met by using my toshiba SMART tv. I can't link my Facebook to my toshiba places account, it shows "internal server error" while trying to connect via the link given in the statement in the email I received.

    Can someone please help?

    Internal server error means that there is a problem with the server and nothing worng with your account.

    No doubt some temporal problems of the server recommend you simply wait until this problem could be solved.

  • Problem with internet connection through WIFI A536

    Hello.
    I bought a few days ago the A536 Lenovo.
    It works very well, it will connect to any wifi that I choose without problem, but after a while it stops internet access without obvious reason.
    He remains connected to WiFi, it keeps the same IP address, I have access to the router (ping works, and I can access the router configuration) in my browser but I don't have access to the internet from any application (browser, Skype, Viber, Mail, etc...)

    I tried a different WiFi (public) and has the same problem.
    (My laptop and a phone HTC Wildfire, Guard works well all the time at home)

    If I just simply disable and enable the WiFi antenna, it connects and it works again for 20-120 min

    I tried to restart, disable Firewall (and security), disable all applications that could affect internet access, add applications 'safe list' firewall, I even downloaded "Lenovo companion" but it is impossible to find problems.
    Wifi after awhile stops all communications to the internet.
    It is very annoying, because no internet means no messages, no emails and no calls VOIP programs.

    Anyone has the same problem?

    Is this A536 fault, or is this the Android 4.4.2?
    Is there a solution, or I have to restore my phone while I can and select a different template, such that it is unnecessary in the end I bought?

    Hi Draculas,

    1 check if there is no update firmware
    2. restoration of the factory

    If the problem persists then take to service center.

  • Why my computer connects to the wifi via time capsule, but not my iphone, ipad or smart tv?

    Yesterday, there was an internet outage in my area. Eventually he returned to the top, but I could not always connect. I phoned by internet service provider and finally they got it working, except now my computer connects to the wifi, but my iphone, the ipad and the smartTV won't. I use a time capsule to connect. Help, please!

    This modem do you have? Brand and model please.

    It is configured as a router or bridge?

    There is a good chance that the TC I messed up in the trouble... It happens.

    Back to the factory and repeat installation... no file is lost it doing.

    Who is your ISP? What kind of services to wide band?

  • Unable to connect to the Network Time Capsule wireless

    I just changed ISP (AT & T to Time Warner) and I use my own modem cable (Arris SB6141). I connected by TC via the WAN and knitting laptop via the connection to the local network, but now only my MacBook Air (El Capitan running) connects to the wifi network of TC. Nothing else connects; AppleTV (w/Siri), iPhone 6s (9.3.1). Is there a compatibility issue that could be the cause of the problem between the modem and the TC? Or is there something I'm supposed to change with the settings? It worked fine when I was using a router 2WIRE AT & T U-Verse.

    Looks like the router Mode of the time Capsule airport is set to Off (Bridge Mode)... (which would have been correct for use with a 2Wire product)... but, it must be set to DHCP and NAT to use with a simple modem.

    Turn off the modem for at least 20 minutes... more won't hurt

    Turning off time Capsule

    Make sure the Ethernet cable from the modem connects to the "O" on the Time Capsule WAN port

    After the 20 + minute modem switch off period has finished, turn on the modem and let it run for 10 minutes

    Then, turn the time Capsule and let it run for 5 minutes

    On your MacBook Air...

    Open AirPort Utility... (Finder > Applications > utilities > AirPort Utility)

    Click on the image of the time Capsule

    Click on edit in the window that appears

    Click on the network at the top of the next window tab

    Make sure that the setting of router Mode = DHCP and NAT

    Click Update at the bottom right of the window and give the time Capsule a minute full to restart

    Recheck the network and report on your results

    Unfortunately, the SB6141 and Apple routers not always who hear well together, so keep an eye on the issues

  • Flash DRIVE - through works of Time Capsule, but not directly to the Mac.

    What I want to achieve:

    -Access to the USB - stick when it is connected directly to the MBA with USB cable.

    The working configuration:

    -USB-drive ("coffee") connected to Time Capsule and used as an external hard drive to save the files (like huge-any libraries).

    Does not:

    -USB-player ("coffee") is directly connected to the MBA.

    Possible cause:

    -The drive is secured by a setting that I could have done on the Time Capsule and so only time Capsule can access.

    More information:

    Solved!

    Well, then shame on me, but it all seemed to give my user rights to access the drive... I thought about it while searching for the settings on the possession of the car.

    Solved!

Maybe you are looking for

  • FF does not start after upgrading to version 27.0.1

    FF does not start after upgrading to version 27.0.1Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  • SD 2 GB card is not readable on Satellite P10 504

    I have a satellite P10-504 P4 2.8 GHz/XP with an SD card, when I insert a 2 gb SanDisk sd card it does not read.What could do?I think that of something maybe drivers upgrade, but I cant find it anywhere.

  • X 220-headphones and microphone port combo adapter

    Hello, I want to save my external microphone as well as the hearing using the helmet on this laptop. Because the connection is a combo Harbour, this means I need an adapter of some kinds. I tried this one: http://www.theheadsetbuddy.com/PC-headset-to

  • How to convert BCD decimal series.

    Hello all, probably a stupid question. I have format timestamp in the BCD data from port series , which I want to convert to display in the form of timestamp based LV. I spent almost 4-5 hours trying to figure out how do - probably my brain froze now

  • My mouse stops Microsoft 3500 work/Black before batteries run out?

    When I got my mouse (Microsoft 3500) I noticed a weird problem after like 2 or 3 days. I took out the batteries at night and when I went to insert in the morning, the blue laser flashing down once and they immediately black. After the light turns off