C4780 wireless printer cannot find the access point

Similar Questions

• Cannot find wireless devices. All-in-one - C309a - "HP printer cannot find your access point"

  Printer: C309a - I have trouble connecting the printer to my wireless network.

  RAN wireless configuration wizard: it ran for a long time but no device not returned.

  Wireles RAN Network Test report: Wireless on - PASS, Wireless - PASS, the name of the network (SSID) found - work FAIL.

  The wireless network Test report shows no IP address on the screen. under mask and default gateway are displayed also as 000.000.000.000

  I have reset to factory settings.

  Other devices took the 192.168.1.250 spot

  My router is visible SSID.

  This is a replacement C309a - my previous C309a - when I ran the test report my previous camera wireless network, said that the radio was not working, so I knew that based on previous posts, that the radio card died and to get a replacement printer. I hope it's a configuration problem and that the wireless on this replacement radio can still work.

  Thanks in advance.

  OK, radio seems OK.  What router are you using?  You've restarted the router by pulling its plug momentarily?

  If anything does not work, we will reset the printer: turn off the power.  Maintain the # and 9 keys while a few seconds after again.

• Launch of Lightroom 6 is not. error: "can't find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library.

  It says: "cannot find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library. What can I do? I have already uninstall and then reinstall the software...

  It is indeed a microsoft problem, check here:error "did not find the entry point _crtCreateSymbolicLinkW - Microsoft Community .

• B209a printer cannot find the new wireless network

  Let me start that I am not very tech savy to start so I read other discussions related to this and could not find a snwer to solve my problem.

  I upgraded my router wireless internet 10 days ago and since then my printer cannot find a wireless connection. That's what I've tried so far, I tried to restart the printer, unpluging it and pluging reconnect, restart my router, myrouter to reset (which knocked my internet at home for hours). The rest of my Office Home phones and cell phones all pick up my network, but my printer can't seem to find it. He said only: "No connection found" on the touch screen.

  I run a wireless network Test report, and he says that he cannot find a SSID. But when I printed on a Page of Configuration of HP network it states that he discovered 5 networks, including mine.

  My wireless router is a rhythm. I have not installed it, did the tech from my service provider. He seemed brand new. I have no way to update its firmware (whatever it is).

  Any help would be appreciated.

  I have solved my problem after reading this thread. http://h30434.www3.HP.com/T5/printer-networking-and-wireless/Photosmart-plus-B209a-won-t-connect-to-wireless-router/m-p/177144#M7026

• HP LaserJet Pro CM1415fnw color multifunction printer - cannot FIND the WIRELESS NETWORKS

  PRINTER: HP LaserJet Pro CM1415fnw color multifunction printer

  OS: Windows 7

  OWNER: More than 2 years without any problem

  LOCATION/SET-UP: To my personal residence. All-in-one router through the cable company.

  QUESTION: Suddenly, printer cannot find wireless networks. Nothing has changed recently in my service provider or equipment. I know that the router and the internet is not the problem because our 2 smart phones and three laptops still not connect. I triend manually configure the network using the SSID and key phrases, but still nothing.

  Help!

  I would like to perform a hard reset by removing the power of the whole machienethrough the power cord for 30 seconds. Depending on whether I have would reconnect the printer to the wireless network and set a static IP address.

  -Spencer

• Unable to find the access point or use any device to all wireless to connect to my BEFSR41 v4.0

  Hi well the problem seems to be that whenever I try to use any type of device and try to connect using a wireless connection to my router, I can't find an access point or no signal at all of it, but when you use a wired connection, it works perfectly. For example, I'm trying to connect my Wii to the internet via a wireless connection, but I can't find any access point so that it can connect to. So I went to my router configuration and I didn't know what to do to allow a shown access point or wireless to all activity. Theres no wireless tab or whatever it is to install, so I didn't allow remote administration, but still I could not find an access point. I don't know if im just made bad or I need an update of the firmware (mine is currently 1.04.02) or what else. If the help would be nice

  BEFSR41 isn't a wireless router... It is wired.

• Cannot associate the Access Point

  I just bought a WUSB54GSC wireless adapter and try to connect to my wireless router, a WRT54GS2, but it gives me a message saying "can't associate with the Access Point.  I tried several times and tried to reconfigure the WEP key, just in case I screwed up somehow and get this message.  I tried the network unsecured neighbor (signal low, of course) and he gave me the same, too.

  What I know:

  (1) the problem is not with any part of my network, either from my lines (DSL), (ADSL) modem or a router, because I use a wired network right now with no problems and several other devices in my house with built-in WiFi to connect wireless to the same router with the Setup even very well.

  (2) the problem is not that I messed up the WEP key.  I rechecked it multiplies and even went to the router via an Ethernet cable to check what I entered compared to what he shows me, and they have a perfect match.  In addition, as previously stated, various WiFi compatible devices in my house using the same WEP key to connect properly.

  So, I don't understand why I can't connect what either.

  First go to device manage and check if the adapter is installed correctly or not... ? If it is installed correctly then, right-click on the utility of linksys (green square) on the toolbar and click on 'Use Windows to configure' and click on 'yes '...

  Now, if you have Windows XP... Click Start and goto the control panel and double-click on network connections, right click wireless network connection and click View available wireless networks and select your wireless network and click on connect... Now, it will give you the opportunity to put the network/wep key, make sure that you enter the correct network key and confirm... It will connect...

  If you have Windows Vista... Click Start > Control Panel > Network and Sharing Center > click on connect to a network, select your wireless network and click on connect, it should ask for your key/password network, enter the network and password correct key and click on connect... It needs to connect... Once you're connected, you must restart the computer, it needs to connect to the Internet...

  Also try to change the wireless channel of the router to 11-2, 462 GHz and then try again...

• c4599 printer cannot find the specified file

  PS_AIO_04_C4500_USW_Full_Win_WW_130_140.exe downloaded and tried to install c4599 printer.  Error system cannot find the specified file "BlockSysUserInstall.exe., which is located in the Temp directory  I noticed that he keeps referring to a coded hard "7zS2F4B."  Have you tried renaming the file in the Temp directory to "7zS2F4B" but still no installation.

  Hi foberg,

  Looks like you have some problems with the operating system installed on this computer. Try the following steps to see if that helps.

  Windows 7 and Windows Vista allows you to have multiple users share the same computer under their own individual accounts. This allows each user to have their own location on the computer where they can store their personal documents, photos, videos, saved games and other personal data. It also allows the owner of the computer assign some accounts the ability to perform administrative tasks such as installing software, while limiting the capabilities of the other user.

  This tutorial will guide you in creating a new account in Windows 7 and Windows Vista.

  1. Click the Start button. It's the small round button () in the lower left corner of your screen that has a Windows flag on it.
  2. Click on the Control Panel menu option.
  3. When Control Panel opens, you will see a screen similar to Figure 1 below.
     Figure 1. Windows 7 Control Panel

• 5525 printer cannot find the wireless network

  Help

  I'm not good with technical stuff and need help with this problem.  Printer works well before going on holiday - power off, including the CISCO router when we went away--returned and turned on any return, printer will not connect to the router again.

  Have reinstalled router without result.  All other computers, phones, etc. to connect to the router fine.

  Wireless network test that the MAC address filtering is enabled, they suggest however have checked this and it's not.

  Wireless configuration wizard can find the network but it just seems impossible to connect to him.

  Please assume the lowest level of technical understanding when you reply!

  Thank you

  Hi K27,.

  I see that you are having some problems getting your Photosmart 5525 reconnected to your network after just unplugging a bit. I understand that you have your information wirelessly, but I don't want to set a link here which will take you to our HP print and doctor Scan, which can help you check some things on the wireless network.

  Since you already feed the router to bike, I would recommend restoring the default values of network on the front panel of the printer. You'll want to have your printer on the home screen (should say Photo, Apps and copy). On this screen you want to touch the key/tool icon in the upper right corner, then you want to click on wireless and made scroll down looking for default network. Once you click on that it will ask if you are sure and you want to say Yes. Once that is done, I would recommend the router/printer power cycling tips that were previously provided and then run the wireless configuration that you've been already and it should be able to connect at this time.

  That should hopefully fix it for you, so let me know what happens and I wish you a nice day!

• PIXMA mx350 is unable to find the access point

  My printer won't find any long my access point. You can find that everyone in the building, just not mine. I tried to kick it. Still no luck. My network is fine. My computer is connected properly. It was working fine and then it all came down.

  Hi again katandmouse,

  So we can help you, please answer with what operating system you have on your computer (Windows or Mac OS X version).

  For immedate assistance, please call 1-866-261-9362, Monday - Friday 10:00 - 10 pm et (excluding holidays) and a technical support representative Cannon will be happy to help you.  There is no charge for this call.

• Printer cannot find the network (iPad)

  HP3050A can't find my airport network. I'm trying to print from the IPad displays-there of printers available in configurations

  OK, I did a bit of homework on this and spoke to the team of Mac here at HP.  The iPad can not implement it (and a few other HP wireless printers) to connect to your wireless network.  I'm sorry.

  You'll have to borrow a computer to configure the printer.  Once configured, your iPad can use very well.

  When you get the computer home, first, click the button on the front of the printer wireless and choose the default settings.  You will have a time of this point for the installed printer.  Download the latest version of the software for your printer from the "Support & drivers" link at the top of this page.

• Adding HP ePrint home and Biz iPhone app - mal printer cannot find the email address of the printer

  I'm trying to connect my HP Photosmart c6380 to my iPhone. I have already downloaded the app and my printer is connected to my wireless network, as is my iPhone, but I can't add my printer to the app.

  When I go to 'Manage ePrinters' and try to add a printer with the + button I see 3 choices:

  Add x to list: "no available ePrinters.

  Manually add: I can't find the printer even email address using the instructions available on the ePrint centre.

  Add the WiFi network: my printer is not shown in this list, so it does not support Autodiscover.

  So I guess that if I could just find email address of my printer that would connect to my iPhone for wireless printing, but I can't for the life of me find.

  Any help is greatly appreciated.

  Thank you.

  Hello amybett,

  I have bad news and good news. The bad news is that your printer is not Airprint/ePrint capable. However, the good news is that with the HP ePrint capable home and Biz iPhone app, it didn't need to be Airprint/Eprint, as it is connected to the same network as your phone.

  Here are the steps that you want to print something:

  1. installation of the application by filling in the electronic registration and entering the code (which I believe you have).

  2. Select the item you want to print by using the menu in the application (Photo Albums, files saved, Web browser, etc.).

  3. Once you select the item, you should see article and a big button "Print" under him.

  4. If the printer you want to print to is not listed above the 'Print' button, select the icon on the right (key/computer), and then select the printer you want to use (and other parameters).

  5. press the button 'Back' at the top left, then tap "Done" (blue top-right button) and then press the 'Print' button to print your article.

  Let me know if you still have problems after following the guide above.

• Printer cannot find the SSID

  This morning the power on the wall where the router is plugged is out. I fixed it and was able to get back on the internet. Problem is that the wireless printer does not work. When I reinstall, my network SSID is not displayed in the available choices. And when I go in the type manually, it can't find it. I'm on the internet. My good names will be displayed. I even went my router page to check these settings. I uninstalled the printer and reinstalled.  I get the same.

  Connectivity report shows the network name (SSID Found)... IN CASE OF FAILURE

  Yet, the networkname is listed in the current configuration of the report at the bottom section.

  Report says also that wireless is enabled and works.

  Why is it not appear?

  In fact, I just changed the name of the SSID and he appeared.

• It is said that cannot find the entry point for Muse and Photoshop? I JUST downloaded.

  

  Please see:

  does not start in Photoshop cs6

  The procedure entry point AMTRetrievePersonGUIDWithAuthSource impossible to find the ERROR.

  I hope this helps.

  Concerning

  Megha Rawat

• Windows 7 or 8 shows the wireless client connected to the access point, but the wireless icon displays "no internet connection".

  I saw the same problem with a different providers wireless solution. When I've sniffed the air with OmniPeek and the network that the ap was conducting with WireShark, I see the arp for the gateway request going to the router, the router gateway response is sent to the suspect machine in the air, the acknowledgement of PC than the package but never fills the arp cache. I watched two arp responses in a vs work for lack of scenario, the two packages are the same.

  The only way I could solve it was to disable IP Helper (not start too) services, reboot the machine. I see 3 to 4 drops per day, but since the deactivation of this Service the machines with that I tested have not seen the question once again.

  IP Helper:
  Provides tunnel connectivity using technologies of transition IPv6 (6to4, ISATAP, Teredo, and Port Proxy) and IP-HTTPS. If this service is stopped, the computer will not have the benefits of improved connectivity offered by these technologies.

  Machines tested and fixed:

  Lenovo E540
  Lenovo W540
  Acer Aspire One
  Dell Latitude E6420

  Ip assistance service has been changed about 40 laptops, a dozen of which would fail in about an hour. So far, 0 out of the 40 saw the question since this change and reboot (reset is the key after disable it) laptops. It's been about 5 days.

  Any reason why disable this Service solves the problem? With it I can replicate the problem pretty quickly on a few different types of machines so it seems not to be driver or provider specific wireless network card. I checked through the Event Viewer logs, but nothing seems to be triggered during the show. Using the Troubleshooter or disconnect the wireless service will fix the problem for a short period only.

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
   
  TechNet Forum
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?filter=AllTypes&sort=lastpostdesc&brandIgnore=true

  Hope this information is useful.