C55-A-100 satellite does not power down after update BIOS 1.30

Similar Questions

• 850 - 009na M1Z34EA #ABU: CPU fan for the 850-009na feel like Phoenix does not turn down after the power - on self test unless the BIOS is entered

  Hello

  I have posted responses to other posts on this topic, but thought I'd start a new thread to gather my conclusions. I'm sorry for a trial

  This PC is virtually brand new (only a few weeks now) and otherwise perform exceptionally.

  Basically, if the machine is disconnected from the power grid (i.e. the power is off at the plug or the power cord removed), when the machine is supplied then the CPU fan turns over 2000 rpm and stays there. All the other PC that I do this too, but the fan will slow down after turning upward. I know that this is done as part of the POST to check that the fan is running.

  If I go into any installation of seed, start-up or BIOS for example (i.e. by pressing ESC or F10 etc.), the fan will slow down immediately up to 700 rpm. It will stay like that until the next time the machine is started against the cold. If I shut down the PC - watch or stop - but do not cut the power supply, then the next time the machine is started, the fan is still about 700 rpm. It is not to turn up to 2 k + RPM when lit.

  As soon as I unplug, then the next time the PC boots, it will turn to the top and I have to repeat steps - off, boot, enter the BIOS, exit and continue. It is something to do with the cold start.

  Note that I don't have to do anything in the start menu - I for example go to the BIOS settings, exit without saving the changes, and the fan will still slow. It's going in the boot sector that slows down the fan.

  When the PC started out-of-the-box, I opted for the upgrade to Windows 10 during installation. I have read in various places that people had experienced after the upgrade, so I reset the machine to factory settings (Win 8.1) and have not upgraded, but the problem persisted. However convinces me that Windows 10 has been removed completely, as when I went to restore the backup image (i.e. dating back to what I had before the factory reset) there are references to 10 Windows (for example, it says 'Continue to Windows 10' as well as various food options). I do not understand UEFI so I don't know if that was involved.

  I tried to change the power plan options "Processor power management-> cooling system strategy" on the liabilities side, but no joy there.

  I think that the fan and sensors work, based on the findings below. These readings of temp and fan are taken from AIDA64

  After starting cold (current was cut, without entering the BIOS), machine runs dry without load

  

  Exactly the same thing--starting in cold, but go in the BIOS, do nothing and continue. Once again, no load

  

  This is after power off and resarting, but to let the PC network

  

  After the above, I used Prime95 to put the CPU support (use of 95-100%), and after an hour, the readings are:

  

  Note that even so, the fan was not particularly strong, but it's at 2222 rpm as in the first reading.

  If I play at 4K (the whole point of the PC ) the CPU so far got very warm, the GPU is but his fan turns up as planned.

  In conclusion, it seems that the POST has a problem because it does not slow down the fan after the test.

  I can live with let the machine always plugged into the sector (for example, most of the time) and I guess that's what most people do, but I would like to know what the problem is (for example if it's really something 10 Windows, or a bug in the BIOS/UEFI)

  Thank you very much!

  John

  Explain you a lot of people who maybe have returned their system immediately because of this? Others might judge normal sound. Not irritable average is not coming here to complain. Others might judge her so little. They simply don't like. You will never convince me that is not a BIOS problem. As the problem resolves itself when you enter manually each time. It can be reproduced every time.

• C50D-A-12R satellite does not power up if the battery connected

  Hello!!!

  I am writing this message cause I was using my laptop and sudenlly it shuts. At first, I didn't know why, I tried to turn it on by pressing the botton, but I failed. Then, I thought I had the battery charger unplugged, but it wasn't. After a few minutes I took the battery and connect the charger, then my laptop run.

  I spend a few hours searching on the Web sites about problems with the battery charger o, and I find that my laptop doesn't recognize the battery cause of pilots o something like this, so I ASK FOR HELP!
  Now, I can only use my laptop if one take out the battery and plug the charger.

  If anyone knows what might happened to my laptop, Please HELP.

  I forgot, my laptop is a Toshiba Satellite C50D-A-12R.

  P.D. sorry my English, I'm from the Spain and several years ago, I finally study English.

  In General, the laptop should work fine in connection with and without the battery.
  The unit should turn on if the battery is removed but connected to the power adapter.

  Also if the battery is connected and worn, the unit should operate without the power adapter connected.
  So what is wrong here? To be honest, I don't think there could be some sort of driver but first of all problems that you should try to recover the laptop to factory settings just to check if the device works by using the preinstalled Toshiba OS and settings.

  If the device does not work properly even after the recovery process, I recommend checking the functionality of the laptop as part of the NEW pile of good work.

  Your device is still covered by the warranty?
  If so, you should communicate with the Toshiba ASP because in case of hardware problems, ASP you should fix free device...

• L775-11N satellite does not power ON battery new

  Hello

  I recently bought a new battery for my Toshiba Satellite L775 11N.

  When I plug in the battery, the battery led blinking stars (according to the manual, it means that the battery has any energy and does not load).

  When it is plugged in, I cannont start the computer, I have to take and put it after.

  What can I do to make my battery work?
  This is the second I buy, from two different sites, the number of model is strictly the same.

  Thanks in advance, sorry for my bad English (french is my mother tongue)

  Hello

  > This is the second I buy, from two different sites, the number of model is strictly the same.
  The part number on the label may be the same, but probably isn t product Toshiba genuine battery.
  You probably bought some cheap battery China labeled as a real framework for this model of laptop.

  > What can I do to make my battery work?
  You have some many options. If the battery isn't fully compatible and does not, you would need to replace it.

• C55-A-1MW satellite does not start with the new RAM inserted

  Hey.

  I hope to find someone who can help me... I bought ram memories and tried 4 different memories in my C55 A 1MW Satellite. But each card RAM I have insert makes the computer cannot start... It lights just to stop again.

  Is there a compatibility issue or anything like that? I used 2 different aData Ram extensions cars, 1 1 and 4 GB 2 GB. the 4 GB card was 1333 mhz and was 2 GB 1600 mhz card. and I tried 2 corsair 4 GB 1600 mhz different cards.

  Is this something that makes only able to expand RAM with Toshibas own memories or is the second cardslot for broken RAM memory?

  As I see you use RAM modules with different specifications. Your problem is certainly of RAM compatibility and you must use the RAM modules with the same specifications.
  According to specification of laptop there are 4 slots of memory and laptop can handle up to 32 GB of RAM.

  The compatible RAM modules are:
  4 GB DDR3L-1600-PA5104U-1M4G
  8 GB DDR3L-1600-PA5104U-1M8G

  Of course, you can use modules from other manufacturers, but please do not use some cheap products. I can recommend the use of Kingston memory modules.

• Satellite L70 - A - 11 c does not power on after upgrade RAM 4 GB

  Hello

  I wanted to add 4 GB of RAM and I took a DDR3 1600 MHz SoDimm of Corsair.

  When the RAM is connected alone or together with the original of the RAM, the laptop does not boot at all!
  I tested this with another laptop RAM and the RAM works perfectly.

  I assume that only the type of DDR3L (1.35v) is accepted and not DDR3 (1.5 V). Can you confirm?

  Do you recommend a specific brand or type of DDR3L which is of course compatible with the Satellite L70 - A - 11 c?

  THX in advance
  CortX

  Hello

  AFAIK the module of RAM 4 G compatible Toshiba was number piece + PA5104U-1M4G +.

  The Toshiba PA5104U-1M4G module is exactly the same as the module of Kingston + KTT-S3CL / 4 +.

  Supports the Kingston KTT-S3CL / 4G * 1.35V* and, therefore, I assume that you have to use the modules supporting the 1.35v and the 1.5V modules would cause the problems mentioned.

  Hope this would help you to get the right RAM module.

• C55-A-1R8 satellite does not illuminate

  Laptop just used to turn on, no noise / response when I press the power button / stop.
  Tried to remove the battery / power supply and pressing power for 30 seconds without result.

  Also tried without battery/power supply, I received a yellow light on the power of battery/led, but now its white.

  I hope someone can help

  Unfortunately there is no magic solution to these issues. On this virtual path, it is not easy to say what the problem with your machine.
  Maybe you tried to install updated BIOS or to do something that could be responsible for this?

  A few years ago, I tried to connect the disk external DRIVE via a USB port, and for some reason, my laptop has some kind of electro shock. The motherboard was dead.

  In my opinion you need professional help, so I think that you contact the nearest Toshiba service provider in your country and ask for help. They have diagnostic tools and methods to check the power of electronic power and find out what's wrong here.

• Satellite A210-199 does not start successfully after the BIOS update

  Hello

  I've got Sat A210-199.
  Yesterday I updated the BIOS, and after that problems occurred:

  While restarting my computer does not start. When I enter the BIOS after a while, it shuts down.
  I guess all this because the temperature of the CPU:

  When I do nothing it is 77 C. I don't think it's normal: (.)
  Computer is very recent, so it's probably not dust inside. And it's so hot from the start, but after the new BIOS, something bad happens.

  Why this temp is so high?
  There is no any process background or something.
  Is this normal?
  And what about this new BIOS?

  To be honest, something like this should not happen. I really don't understand why this is happening. I have updated the BIOS on friends A200 and mine P200 and everything works fine. Here on this forum we can only speculate on this issue, but what you need exactly's professional opinion.

  This probably not help but install recovery image and check with the factory settings. Make sure you also on the lower side cooling fan is not blocked and the laptop can be cooled properly. If the problem persists, you should contact the nearest authorized maintainer and clarify this issue.

  Sorry, but I don't really know what you can do in this situation. I don't see any other way to solve this problem.

  Good luck!

• Laptop HP Pavilion 2320DX g4: computer hp laptop pavilion g4 does not start successfully after update and return to windows 8.1

  Hi, I have recently updated my laptop to Windows 10. He had so many problems and I didn't like it at all, so I just returned my laptop to Windows 8.1.  Since then, my laptop does not correctly every time, and the fan immediately starts to work as well. I can start my pc and connect to my home screen each time.  If the tile is moving or light up when I move my cursor, then I know that I can use my laptop for a little while. It can freeze after getting out a good program. Other times when I start my laptop, everything is dead except for logging on my screen. My Windows key on the keyboard does not work most of the time.  If the screen does not respond the first time I turn, as described above, I can't absolutely nothing on my pc. I can't access the search bar by moving the cursor to top right, I can't open the tiles, I can't spend in desktop mode, etc.  Front I upgraded to Windows 10 and downgraded to 8.1 all worked perfectly, because I've updated from 8.0 to 8.1 Windows almost 2 years.  I have a defective battery. in fact I can only use my laptop if it is plugged. My fan is constantly going, but I don't know if it's my loss of battery or what's wrong with my pc now.  I have described my problem in the Microsoft community forum but have had little response that was not helpful. I was told to go to the command prompt and put in DISM: scan now (which also contained letters more than that, but I do not remember all). I followed the instructions and for 2 days, my pc seems to do better. Then he returned to this problem again. I hope you can help me.  If you have additional questions, post here or please email me at [removed personal information]. Thank you!

  DEB

  @DWESTDEWITT,

  Hello and thanks for the display on the HP support forum.  What you can do at this point that there are several updates released by microsoft and hardware vendors is running the Windows Update Troubleshooter.

  If this fails to solve the problem.  The only option will be to restore the operating system to the previous, until HP gets the drivers so that they can release them on the support page for your laptop for Windows 10.

  Thanks again for posting and have a great day.

• Satellite C50B freezes at startup after update BIOS to 5.10

  Hello
  I updated the BIOS of my Satellite C50 - B - 14 d (PSCMLE) to 5.10 (a final release early sept. 2015).
  The update succeeded, and the laptop runs as long as I do not install the drivers for the card WiFi (Atheros AR9485).
  If I try to install the driver (it does not matter which, those of the Toshiba website or those of the manufacturer, of), the laptop crashes before the end of the installer.
  Installing drivers from Device Manager makes the laptop freeze on when Windows starts (I tried 7, 8.1, and 10).
  Completely on the Windows logo screen it freezes, and I have to turn off it.

  In addition, the wired network adapter is not detected (it does not appear in Device Manager).
  The same question is described here (http://www.eightforums.com/general-s...ses-start.html), but no solution.

  Any suggestion? The BIOS may be downgraded? The BIOS update utility does not Flash an older version.

  Thank you!

  Hi indutry,

  I also have exactly the same problem since updating my BIOS to 5.10 with my Toshiba C50 - B - 14 d PSC MLE

  I have to start windows in safe mode without network to disable the Atheros AR9485 before restarting again in normal mode.
  I now have to use an external WiFi adapter as my LAN port is now also lack!

  Upset that the BIOS update has broken all my embedded network on the laptop.

  I tried to update the Atheros drivers to the latest version, but as soon as the device is turned on again the system crashes and we're back to square one.

  There is no solution that I can find other than turning off the unit and live without built in WiFi + LAN.

  I hope Toshiba can be remedied with a new BIOS update?

• OptiPlex 990 not PXE boot after update Bios A18

  After the update to A18 on multiple machines, I noticed that they all hang after address DHCP is affected and what would normally be the menu timer (if it was not all work in progress) or launch from the boot of automation.

  I also noticed when you update to the latest version on our Latitude E6420s so.  Returning to the A17 on the 990 and the 6420 corrects this problem.

  Is anyone else having this problem, and this Signals to Dell.  I tried to Google this but any how, I wrote the search I can't find anything with recent BIOS.

  Hello Irios103,

  It is difficult to determine what is causing the conflict with Bios version A18 and your systems. The improvements to the code may be the cause of problems on Cisco switches or oldest feature, such as the tree covering weight or the characteristic power of conservation.  You can also make sure the quick port is enabled.
  If you do not need specific to this version of Bios patches, it may be better to not use it.

  Improvements & fixes for version Watch:
  1 address system does not meet the keyboard intermittently.
  2. address UEFI OS fail boot with this disk number HARD password.
  3. questions of CCTK.
  4. improve the compatibility of PCI devices and USB devices.
  5 Update Microcode Intel SandyBridge processor.
  6 update Intel PXE ROM.

  I hope this helps.  Please let us know if you need further assistance or more information.
  ~ Maureen
  #iwork4dell

• Satellite C660 - no Internet connection after updating BIOS

  I am a novice user and have a Satellite C660 under warranty that I don't use for surfing the net and Ebay so I hope I can explain my problem!

  Toshiba bulletin board said that the need to update BIOS, so I followed the instructions but since then I have no internet connection, and cannot restore the connection that I lost all help Toshiba Bulletin Board today lost and none of the programs to sort the problems work - e.g.set assistants etc. I did not yet create rescue disks, but if I try to create them now I'll be able to restore to factory settings?

  Can someone tell me if it's a failure caused by the BIOS update or I would return laptop to John Lewis for repair? Thank you very much for reading this

  Hey Buddy,

  The default settings in the BIOS load after update? If this is not the case, go into the BIOS and load the default settings. You can enter the BIOS if you press F2 before Windows start and then press the F9 key to load defaults. Then save & exit the BIOS Setup.

  You can access the Internet now?
  You try to access the Internet with LAN or WLAN connection?

  Also check device manager if all devices are recognized correctly.

  > I did not yet create rescue disks, but if I try to create them now I'll be able to restore to factory settings?
  You can create the Toshiba Recovery disk every time. Just launch the pre-installed Toshiba Recovery Media Creator and follow the instructions on the screen. You need just a few blank DVDs to create the discs. Disks contain a factory image of settings which can be restored each time and how many times you want to so with these disks, you are on the safe side ;)

• Satellite A60: Problem of memory after update Bios V.1.9

  Hi all

  I've just updated my bios to version 1.9 last week. Previously, I've upgraded my RAM from 512 MB to 1.5 GB (P4 2.8 GHz., 40 GB HARD drive) and my phone worked perfectly with the old Bios and RAM. After the Bios Update to the new version, 1.9, my laptop does not accept the module of RAM upgrade, windows xp still shows the blue screen, and then restart.

  After upgrading RAM off, my laptop works again. I tried several ways to solve this problem as take the battery, then reinsert the RAM or even formatted my HARD drive and installed a new Windows XP, but it didn't work. So what can I do to make my laptop to accept the upgrade of RAM? How to solve this problem? For this reason I now intend to buy a new laptop, if the problem can not be solved since I simulate a program on this laptop, so it requires a lot of memory.

  Thank you very much in advance for your answer.

  [Edited by: admin]

  Hello

  I put t really know what is the problem with the new update of the BIOS. In my opinion, you should contact the after-sales Service of Toshiba partner in your country and explain to them the situation. If your new module memory is compatible with the unit you should tell you want to have the old version of the BIOS. As much I know as technicians for this.

  If they see that there is a problem with the BIOS update, I'm sure they will for free.

  Good luck!

• C55-A-1R9 satellite does not illuminate

  Hello

  My Satellite C55-A-1R9 lights. I tried the button down, taking the battery etc.
  Help, please!?

  Hello

  Are there no reaction at all?
  DC/battery is turned on when you connect your laptop to the power adapter?

• Equium MX40-103 screens towers but does not power down

  I have the above model. The laptop works well except for the fact that the screen turns off but is still running.

  This can happen in 10 minutes or after hours, I can't find one any relationship with the problem.
  However, the laptop will beep once for a longer time, then twice for a shorter duration, then the screen turns off.

  This occurs when the computer is loaded up, is not when loading windows. Thanks for helping me

  Hello

  Have you tried updating the graphics card driver?
  What about your BIOS version? If the latest version is available on the Toshiba page that you could try to update. But be careful! Don't forget to use the good BIOS and use the right update procedure

  Anyway. I read somewhere on similar problems and it seems to be linked to the main Exchange of bad parameter between LCD and PCB.
  This can be caused by a damaged ROM chip on the LCD screen.
  But to be 100% sure, you will need to contact the service point.