cable detection map... again

I have a tuner card Haapauge 2650 Cable with Frontier FIOS cable adapter installed in a Windows 7 computer.  Windows Media Center usually works well with the following exception:

WMC - periodically displays the message... "map of cable detected... you want to run Setup now?  ... but the map has already been implemented, and everything seems to work fine... except that now I have to click on the message "detection" to make things work again...

Any ideas?

Hello

Please follow the steps below.

Method 1:

Run the troubleshooter mentioned in the link below.

Open the hardware and devices Troubleshooter

http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

Method 2:

Install the latest drivers for the tuner cable 2650 card Haapauge from the link below.

http://www.Hauppauge.com/site/support/support_dcr-2650.html

See also the below mentioned link.

Digital cable tuners: frequently asked questions

http://Windows.Microsoft.com/en-us/Windows7/digital-cable-tuners-frequently-asked-questions

Tags: Windows

Similar Questions

  • Easy transfer cable detection problem

    While trying to transfer files etc. from old computer using Windows XP Professional version 2002 service pack 3 for new computer using Windows 7, I get a message on the old computer indicating "Cable Easy Transfer undetected." The cable is fine because it works with another computer.

    FOR ANYONE WHO IS STILL HAVING THIS PROBLEM I THOUGHT IT!

    Shouldn't the Systemengineer Microsoft had to know this?

    Here's what worked for me.

    1. on your XP machine, check if you have Windows XP 32 bit (x 86) that you use/download version 32-bit (x 86) Windows Easy Transfer.

    2 install.

    3. you must now do a right-click 'my computer' and select 'Properties'. Go to the "hardware" tab and click on "Device Manager".

    3. now that you're 'Device Manager' connect your easy transfer cable.

    4. it should refresh and you should now see 'cable devices transfer' (mine had a question mark logo, which indicates that the driver was not installed...) Click the small 'sign' next to him and less must be something called 'Simple cable USB transfer' (this is what it says for my Dynex brand cable anyway...)

    5. right click and select "Properties". Go to the tab "driver", then click on "Update Driver".

    6. the "Welcome to the Hardware Update Wizard" should appear. Select "install from a list or specific location (Advanced)" and click "Next".

    7. Select "Search for the best driver in these locations" and also select "include this location in the search:

    8. now click on 'Browse' and navigate to the folder where Windows Easy Transfer installed in (something like7\cable C:\Program Files\Windows Easy Transfer according to your drive letter) "cable" is important. This is the driver. Now click 'ok'.

    9. click on ""Next ' and it should be a small thing of research. " Then when it's done it will probably say that your driver has been installed. It must not be an exclamation mark next to the name in "Device Manager" more.

    10. now run Windows Easy Transfer and it should recognize the cable. It actually automatically recognize the cable now when you plug it in.

    For some reason when you install Windows Easy Transfer it does not install the cable driver and you must do it manually.

    Now, I had another problem with mine. He repeated (on my Win7 machine) that it would take something ridiculous like 4 hours... then on my XP machine, a box would come and say "Trying to reconnect" and everything to stall. Disable your screen saver, screen off and standby (in power settings) on both computers. If that not help I also found that you do the transfer in the sections, do not try to transfer ALL in one session. As I made my photos, and when this was done I did my music, etc...

    I really hope this helps someone. I hope I've heard a few comments!

  • How to make my Magic Trackpad roll again and also how to make the detectable trackpad again?

    Recently updated our mini mac of aging for OS X El Capitan and now the Magic Trackpad to scroll. It points. It snaps. But no scrolling. When I look in Preferences system under mac trackpads can not see the trackpad, even if I use the trackpad to navigate. When I try to connect it in preferences I bluetooth, a spinning wheel, but it does not connect. How the mac for one.) See the new trackpad and b). scroll? NB. Trackpad has fresh batteries and it is turned on.

    eyboard-work-with-your-Mac-3628013/ http://www.Macworld.co.uk/News/Apple/will-Magic-trackpad-2-Magic-Mouse-2-Magic-k

    You can find this article useful.   I suspect that you will need a new trackpad, but I'm not sure of the requirement of bluetooth of your Mac Mini.

  • Belkin easy transfer cable was not detected

    Hello

    This is a follow-on to the following thread that no one has answered: http://www.google.com/url?sa=t&source=web&cd=1&ved=0CBwQFjAA&url=http%3A%2F%2Fanswers.microsoft.com%2Fen-us%2Fwindows%2Fforum%2Fwindows_xp-windows_install%2Feasy-transfer-cable-detection-problem%2F15531c4f-a8bd-469d-8856-e7b231a8b6f4&ei=oB54TdyyLOKZ0QGxnYTuBg&usg=AFQjCNHxadqvOGSsNX8yfISqm7ApnGwcJw&sig2=eEm_LvFe34X66AkzRPfxBg

    I hung on to step 8.  I couldn't find the folder "Windows Easy Transfer 7".  I however find a folder "Windows Easy Transfer", but could not find the folder "cable."  He had two subfolders (amd64 and x 86) which each included dozens of other records.  Can you direct me to the correct folder or even better yet is their a link online to download?

    Help please!

    Hello

    If you have 64-bit Windows XP installed, you can go to the folder amd 64 and thencheck for the folder. Widnows XP go to 32-bit X 86 folder.

    I hope this helps.

  • EA3500 not detected during installation

    I had a router (EA3500) wifi linksys n750 chip to use with a scientific atlanta cable modem. Initially, I tried to set up on my girlfriends laptop but because the installation program REQUIRES wifi, she didn't. (the wifi on this laptop is down). He got up to 85% filled including having put in place the SSID and password. but failed to set up the internet connection. So I tried to put up with my laptop instead. I unplugged the modem and router for more than 5 minutes each, and then began the installation program. It reaches 25% and then asked to not be able to detect a linksys router. However, I checked my taskbar, and he said that I was connected to the router under the SSID I had put in place previously. So I tried the option "I have configured my router and want to connect to it", I entered the SSID and the PW, but still he could not connect. I used the reset button on the router for if all right to restore it to factory settings. Now when I try to install it doesn't have the SSID tthat had already together (the router is now identified as "Cisco 00259" or something like that), but it still fails to 25%. He also said that it cannot detect a linksys router. What is going on. I know that the Wifi is working on this laptop. I cycled the modem and the router enough times to be sure that is not the problem. How to spend it?

    Error code: 0x82BF010F
    Error description: No Linksys Router wireless networks were found.
    Model name: EA3500
    Model description: unknown
    Serial number: unknown
    Firmware version: unknown
    Operating system: Windows XP SP 3
    Software version: 2.0.14294.0
    Connection type (WAN): unknown
    IP address (LAN): 192.168.1.1
    IP address (WAN): unknown
    Computer IP address: 192.168.1.146
    

    The Setup program requires no wifi. Connect to the router with an ethernet cable and try again. If installation does not try to connect to the router with a browser to 192.168.1.1 and configure manually. The password will be "admin" without the quotes.

  • Web site does not detect my version of Firefox

    Sorry for my bad English I'm french.

    I had a problem with firefox: when a go on youtube, twitter,... He told me to upgrade my firefox. If I look on "About Firefox" in my browser, it says: version 3.6.3.
    I would like to install an add on but he said that my version is not compatible.
    So I think I have a problem with my version of Firefox by site detection.
    Again, sorry for my bad English ^^

    This has happened

    Each time Firefox opened

    Is a few months ago

    Check general.useragent preferences on the topic: config page.
    You can open the topic: config page through the address bar just like you open a Web site.
    Filter: general.useragent
    If all general.useragent prefs are "BOLD" (user set) then right-click this pref and select reset.

    See find which version of Firefox you are using and Web sites or modules incorrectly report incompatible browser
    See also http://kb.mozillazine.org/Resetting_your_useragent_string_to_its_compiled-in_default

  • Vodacom k3772-Z not detected on Satellite L755 USB 3.0 port

    Good day to all,

    I kinda a strange problem, the company that I work received point on the toshiba Satellite L755 PSK2YE and a box of vodacom K3772-Z modems for distribution to our customers.

    We picked up that these modems are not detected at all when plugged in the port of USB3 laptops left side (we tried 3 modems on machine Ong 3 with the same result each time)

    Modems work perfectly well when it is connected to the usb ports on right 2 and all the rest that we connected to works of 3 usb port very well including older models of modems.

    I also tested the modem on another machine of 3 USB (also using the usb controller 3 renesas) and it works beautifully.

    I have notcied that if you disable the usb controller 3 on the laptop and turn it back on with the stick of 3 g connected to the unit is detected correctly however if you unplug in and try again once it does detect it yet.

    It's using the latest drivers and firmware.

    I tried to find a solution online but had no chance.

    Any ideas what could be the cause?

    > Modems work perfectly well when it is connected to the usb ports on right 2 and all the rest that we connected to works of 3 usb port very well including older models of modems.

    From my point of view it would mean for computer laptop USB 3.0 port works correctly and, possibly, there is a compatibility problem between the modem and the USB 3.0 port. Maybe you should contact check the modem manufacturer support page for more information

    I read on some forums that many people had problems to install this modem using Win 7 64 bit with 32-bit system was not a problem, someone used the drivers released for modem K4505.

    Someone else solved this facility a 10.2 Vodafone
    + 1. Go to start menu.
    + 2. Run regedit +.
    + 3. Open this key HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E96D-E325-11CE-BFC1-08002BE10318} +.
    + 4. In this key, search for the string of Installer32. +
    + 5. If missing the Microsoft registration key, the key must be added manually. +
    + 6. Create a string value named Installer32 and assign the mdminst.dll, ClassInstall32 +.
    + 5. Save the regedit +.
    + 6. Open the device manage +.
    + 7. Find the modem with the problem; uninstall it and let windows detect it again (or search the hardware changes). +

  • Impossible to use the DVI - D port with cable DVI - D Pav 500-100 a to HP W2207 monitor

    I have a new standard of factory Pav 500-100a without mods.  HP w2207 monitor.

    Currently properly connect with VGA DVI - D port with the adapter supplied with the pc.  I have install Windows Update 8.1, put in my files from my old PC and everything was fine except the video is not very good.

    I got a formwork of cable DVD, but it's a DVI-I have the cable.  It took 5 minutes before windows comes up and then whenever the background picture changed in the theme which he suspended for a few seconds.  I read that I have a DVD-D need cable which i purchasd today.

    The package says it's a CL-DVI2M - DVI M/M 24 + 1 CABLE 2 M.  The tech in the store said that it is a good calbe and works perfectly.

    When connected and power until I get the hp and rolling points logo, then it turns off.

    I reconnect the cable VGA and all its beautiful - using the VGA to DVI.

    I ran msconfig and turned from secure boot - restarts and comes well in safe mode.  I set the resolution of 1280 x 800 and rebooted and reconnected the cable DVI - Virgin again.

    If I put the cable VGA back inside fine boots.  The monitor was given factory and seens the DVI connection but Windows remains empty. Also tried to start first with no cable - connect the DVI and the monitor remains in sleep - be able to reset the monitor and still a Virgin is also no connection DVO.

    I have fI switch with connected DVI I can get to the BIOS, and I see the HP logo and the points Win 8 starts.

    I don't know what else I can try.  I have no other usable with DVI video card

    Any ideas out there?

    Pls help - Steve

    Although I am an employee of HP, I speak for myself and not for HP.

    Yes, I rasthaus the monitor and cable of my older Compaq running xp and all fine on DVI.  The monitor and cable are fine.

    Since then, I've had a product in Australia specialist help.  Tried all the previous things, then initially went to check if the person had been doing the right thing - connected the VGA monitor with the supplied adapter DVI-d port - which has always worked well.

    Went to Device Manager o and removed the video card adapter. Powered off and then attached the monitor directly with DVI and it started late! Drviers reinstalled and updated and now I have nice crisp clear video appears.

    Something of the support person should apparently have - insead has asked me to wipe the hard drive and restore the factory system, replace the cables, buy a new monitor... was even asked to leave VGA mode and do not use DVI!

    Thank you for your help, Dave, its good to know that you are around to help us.

  • Replacement cables SHC68-68-EPM?

    I have a PXI-6363.  The recommended cable is the SHC68-68-EPM cable.  I have one of these practices, but need 2.  I found a couple of unused cables carrying around (NI SHC68-68 - RMIO & SHC68 - 68 - RDIO).  Can I use one of these as a substitute for a cable EPM?

    I am not convinced that you can simply replace them and if they don't work it wouldn't be ideal. On the one hand, the SHC68-68-EPM cable specifies that it ends by a shift of VHDCI 68 pin, while others are just VHDCI, but I was not able to find information about the difference. In addition, they list compatibility for X and M series for RMIO or RDIO cable. While they are all 68 pin cables there are huge differences in grouping and shielding wire, and they are all optimized for different features/data acquisition cards. I found the mappings of wire for the EPM and RMIO which illustrates this.

    Wire mapping list to the SHC68-68-EPM cable

    http://digital.NI.com/public.nsf/allkb/DE2D842E545DE64B86256F78006EAB1A

    RMIO cable Wire Mapping

    http://digital.natinst.com/public.nsf/ $CXIV/ATTACH-AEEE-88AQJT/$FILE/SHC68-68-RMIO.png

  • Remove the old cable network name machine Vista

    I have 4 computers on a home network (2 portable wireless, Windows 7 and Vista) and 2 desktops (also Windows 7-Vista) to Windows 7 computers, replacing Vista computers in the near future.  Until them, I always use the four computers.

    I had a LOT of problems (unable to access printers and printers go offline) sharing printer and recently started having "Windows cannot access \\theWindows7newdesktopcomputer", those with printers attached - and I could / can not find a solution for this.  In desperation, I have reset the Linksys router e2500 manufactured back State initial and in the process gained a new network name (do not change).

    My problem is that the old Vista computer wired to the router insists on the use of the old network name (the one that appears on the screen of the network and sharing Center).  The funny thing is that I put on Jack autour with him (nothing has changed on the router) I have now access to the Internet on the old Vista computer wired to the router, even if she seems to be using the former name of network.  So, how can I get the Vista computer to recognize the new network name and quit using the former name of network.  I spent all day on this problem and I am not farther than I was when I started working on the problem of this morning on the printer share.  I guess that the router works because these two computers are connected to the router, but it doesn't look good for me and it seems that it must be something I can change or correct.

    Ron in round rock

    Try to remove from the network and sharing Center by clicking on the Home icon next to network name and go to mergere or delete network locations. I guess you know what to do after that.

    If it is used, then unplug your ethernet cable and try again.

  • Are there plans to allow place dell 8 pro takes care of micro adapter USB cable?

    I have a micro USB to USB cable that allows the device which will be charged at the same time, but it does not work with the venue Pro 8. Any ideas on the question of whether it is a physical limitation or something software related?

    I now have the answer to this query. It is a restriction of the standard USB and the requirement for OTG cable detect what USB is connected. There are a few explanations on the web around this behavior on the web if you search for them.

  • DREAMWEAVERCC 2015: Creating Image maps, please help!

    I have had no problem of creating interactive images before this last update and now I can't even image to align, fine not the real problem: create and edit clickable images. Don't know what happened, I'm in a transitional doc 4.0 that I built the last image maps in. Now, the only way it appears is if I select the code, which is fine, but as soon as I try to draw the map/edit I'm stuck back.

    Shot in the old code from the working file and I can't change it (same question, select code, option, select either the arrow select card or draw a shape, start drawing and then locked) so I'm not sure what should happen.

    There are image maps for us in these pictures.

    Are you accidentally in Live View mode?

    Design and Live are now in a drop-down menu in the taskbar near Code and Split. The editor in Live mode does not image mapping again.

    If you don't have the design view option in the dropdown menu with Live, you will need to make a small change to your fluid grid css file to retrieve.

    If you are in Design mode and the Image Map tools are not displayed, you should see a small triangle at the bottom right of the main window of properties that you can click to retrieve the IM toolbar.

  • OfficeJet 7500 a: inaccessible Scanner

    My HP printer/scanner/copier Officejet 7500 a can not be detected by my Windows 7 desktop PC - but ONLY the scanner.

    Message that displayed when I try to scan:

    [Inaccessible scanner

    [Scanner communication cannot be established. If make sure that your product is powered, check the connection and make sure that your network is working properly. If these conditions are correct, restart the product and try to scan the image.
    If you have installed this printer by IP address, you may need to update the IP address. Use the IP address update for this printer start menu entry.
    If you are running a software firewall, it can block scan communication. Please visit www.hp.com/go/wirelessprinting for help to configure your firewall.]

    I do NOT use wireless scanning. I have NOT installed the printer/scanner by IP address. The printer/scanner is connected directly to my PC via a USB cable.

    Copy works fine; printing most of the time but sometimes the PC sends a print job that prints ever (and no error message). I have to unplug the power cord and plug it in again, which resets the printer and then the job will print if I return it. (I leave the printer on all the time so I don't have to turn on my PC, if all I need is the copier function).

    I do not use the scanner very often, but I have had this printer for 4 years, and the scanner has always worked in the past.

    When I got the Windows message "Inaccessible Scanner", I tried to unplug the power cord and in reconnecting it back, but the scanner was still "inaccessible". I also tried unplugging the USB cable and plug again, but still not to scan. I also tried to plug the USB cable into a different USB port on my PC, but not scan. I tried to reinstall the scanner, but Windows does not display the scanner as a device.

    Is there anything else I can try to solve the problem of 'inaccessible Scanner?

    Thanks a lot for your help!

    greenturtle wrote:

    ... If this does not resolve the issue, can you try uninstalling and reinstalling the software features FULL?

    Hope that helps.

    Hi, greenturtle:

    Thanks for your reply. I solved the problem by uninstalling and then reinstalling the full features software - and that solved the problem!

    Cyndi

  • Readers compatible recovery/Bootable with Portege R200

    Hello

    I am looking for a for a R200 bootable recovery disk. After contacting Toshiba, told me that the only recovery disks they know of and support for the R200 at the moment are the readers of Toshiba official marks. I know that on some Toshiba models Targus readers are also supported but are not necessarily supported on the R200. What I want to know is if anyone knows of other external optical drives that can be used for the external optical drives toshiba recovery disc are extremely expensive.

    Personally, I tried a samsung DVD-Rs (TS-552U) in an external enclosure 5.25 inches (appears as a USB mass storage device in Windows XP) and it takes to the extent where the options of recovery, but cannot go further (i.e. you choose what desired recovery option, it reboots the machine, and then asking you to wait (, and then gives a warning message that the CD/DVD drive is not found).

    I also tried a Sharp CDRom PCMCIA (CE-CD01) it's 16-bit with Cardbus (I already used this cover my Portege R100 successfully) but it gave me the same problem as above.

    I also followed the instructions here:
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=5994&TSTART=15
    However when I start first at one of my two CDRom above it detects the CDRom and starts on the recovery CD and gets the recovery of three options. After selecting one of the three options, it restarts the computer, and then asking you to wait. And then it displays a warning message that it cannot detect any CD/DVD drive. Therefore, this set of instructions does not work for me. I know it has nothing to do with my recovery disks because I had to take my computer to a service center in the reconstituted BONE, and they have been able to do successfully.

    I also searched a document like this (http://support.toshiba-tro.de/kb0/TSB5100S70004R01.htm) for the R200 nothing helps.

    Note also that my computer is an Australian R200 (PPR20A - 01 K 003) is that it makes a difference?

    It would be greatly appreciated if I could get your entry! Thank you!

    Gene

    Hello

    As you have said about your only Toshiba drivers are supported to use the recovery procedure.
    The Portege M200 supports the recovery through the BIOS (by pressing 'C') with the USB 2.0 card and PCMCIA (16-bit and Cardbus).

    Readers and following (USB, PCMCIA) controllers have been tested successfully:

    one) Toshiba, PA3352E-SCD2, CD-RW/DVD-Rom USB 2.0 drive
    (b) Toshiba PA3402E-1DV2, Rev.501, USB 2.0 DVD Super Multi drive, SN: 5362870112
    (c) Toshiba, PX1055E-1NST, (Freecom drive), SN: 3431490096
    with a PC Card (16 bit) card, cable II, PCMCIA, Rev.043.242, SN: 18496 043 3999 0343 01093
    (d) Toshiba, PX1055E-1NST, (Freecom drive), SN: 3431490096
    with a CardBus cable II, MAP of BUS, Rev.136, SN: 16693 136 3999 0149 06122

    Sorry I put t see any other possibility of recovering your unit. You need the reader compatible recovery.

    Good bye

  • Satellite L350 - 17Q - unable to connect to WiFi Win XP

    Hi all

    I removed Vista on my new laptop and after a clean format (now I'm also the creator of disc I guess) I installed XP.
    I installed all the drivers and also wireless Realtek driver and Atheros Wireless Manager.
    I installed as LAN driver so I could connect to the internet with a cable.

    Again, I uninstalled drivers in windows control manager system: ethernet controller...
    My wireless connection is still not visible and cannot be detected by the wireless research (toshiba utility).

    The wireless switch is turned on and the sign is on.

    What could be the problem?

    Concerning

    min1kuke

    Great!

    Thanks for the comments. :)

Maybe you are looking for

  • The movie widget

    My movie widget stopped working two or three days ago.  Anyone else having this problem, and everyone knows how to fix?  It was a great, useful widget, and I use it all the time.

  • take e - 250 for pc songs

    is it possible to take music off my e-250 and put it on my pc, I guess you call it reverse synchronization? snarehead 123

  • Why can't get my Hotmail attachments to attach to their emails?

    Whenever I hit him "attachments" my attachment fails to join!

  • HTTP 400 error

    Please HELP.every time I try to go on a Microsoft fs site, either directly or via a link iget the following report"HTTP 400 error. The request is malformed. "I can't even contact MS for helpany ideas will be appreciatedTHXJames

  • Free movies of blackBerry Smartphones?

    Are there sites where you can download FREE movies on BlackBerry you?