cable not connected network

Similar Questions

• I have norton antivirus online via my ISP and I had to disable, because it comes with an error that says "cable not connected or missing network adapter" I use dial-up.

  cable not connected network adapter

  I have norton antivirus online via my ISP and I had to disable, because it comes with an error that says "cable not connected or missing network adapter" I use dial-up and do not use any type of router and I'm not on a network. I also tried to disable my network card & it still says the same error. I have an internal network card that came w / the computer (NOT a PCI one) and I wonder if there is a cord or a plug inside my computer that must be plugged. I made some changes on the internal hardware and might have missed an and I didn't have to open my Tower if it wasn't. It's a big hassle! Help, please!

  Hello

  1. Once you get the error message?

  2. do you get the error when you try to disable Norton anti-virus?

  3. are you able to access the Internet explore?

  Temporarily disable the antivirus on the computer running software and check if you are able to install the software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  WARNING: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

• "Cable not connected to the network adapter.

  WRT400N did not come after start stop and cold pc.  Windows Vista repair & diagnostic returns "cable not connected to the network adapter.  I tried to plug and re - plug cable ethernet; router power off (+ 10 sec.); Linksys repair; reset the modem, etc.  The success of the Internet, but no router.  The only solution is a pc "restart" and then the appropriate router port lights up and all is well.  What is the real solution please?

  Hi Helm,

  I finally got the router to work after several reboots and struggles.  in any case, I'm always game to try almost anything if you have any other suggestions...

  Thank you

• Realtek 81xx NIC "Cable not connected" with WRT54G2 on Windows Vista

  Hello, I have this weird problem with Realtek 3 different integrated NICs, connect to a WRT54G2 configured as an Access Point.

  I have installed and configured the WRT54G2 without any problems using my computer laptop buildin NIC and wireless adapter, it worked like a charm. However, try to connect two different PC with integrated NIC Realtek 8168 me Gets the problem of "cable not connected". When I click on this cable in to my laptops NIC, it works.

  I've tried everything. In advanced settings, I changed the speed to 10 Mbps, 1000 Mbit and 100Mbit and back to auto. nothing. When I plug the cable in 10Mbit, the lights on the NIC on briefly then darken again. When they do not appear there is a message "unknown network".

  It is not energy saves the settings, I turned them all off. Also any firewall setting is killed on the clients.

  I even bought a cheep * beep * PCI NIC, which has been using a Realtek chip set 81xx; don't turn back, "cable not connected" everywhere.

  I've never seen anything like this. With any other router is most of the configuration work, now, I spent the evening in the hope of seeing the yellow and orange lights flash to appear. This is the way to complicated for no reason.

  Anyone can say anything about it? I think to get to a simple Belkin do the work.

  Have you tried another ethernet cable... Try it.

  Connect to the Linksys configuration Page and reduce the size MTU to 1300 and click on save settings.

  You can also try reducing the map of the computer (NIC) speed to 10 Mbps half duplex / 10 base mode half T/10.

  If the foregoing, all action does not work, try to reset the router for a minute... Check it out now.

• Satellite L850-1v0 - alert "Cable not connected" when external monitor OFF

  Hi all

  I have a portable Satellite L850-1v0.
  My monitor is an A.c.e.r X233H
  Windows 8

  I have the setting 'Disable the display' 5 minutes.

  However, when the laptop off the screen I get a small box that bounces around the screen stating "Cable not connected". The monitor is connected via the VGA port.

  If I connect the monitor to my other machine it turns off fine and do not show this message.

  How can I get the laptop to turn off the display correctly?

  Thanks in advance
  Richard

  > when the laptop off the screen I have a small box which bounces around the screen stating "Cable not connected". The monitor is connected via the VGA port.

  The message appears because the signal to the external display was interrupted because of the setting: turn the display off.

  > If connect the monitor to my other machine it turns off fine and does not show this message.
  I think that the other computer/laptop supports another graphics card and so this message does not appear.

  Satellite L850-1v0 support and use of the 4000 Intel HD Graphics intern, who is part of the processor Intel® Core i3 - 3120M and this graphics card shows these alerts

• H233H"cable not connected" with the computer is turned off

  My H233H monitor displays an annoying blue "cable not connected" when my computer is off or in stand-by mode.  Monitor works find out otherwise and all the buttons on the front panel work.  But impossible to find a setting that will turn the monitor off when the computer stops sending a signal.

  If I unplug the cable from the monitor to the computer's HDMI, should not the monitor eventually fade or go to sleeo?  Or will she continue to display this message "cable not connected" blue indefinitely?

  Thank you

  Well, I realized that it is a problem of Acer monitor with HDMI input.

  There is no problem if I connect my H233H monitor with VGA or DVI cable.

  Just thought I'd come back and answer my own question if someone ever comes back here with a similar problem.

  Good luck...

• Not connected network card

  My laptop says he not a network card, I can't connect to internet via wifi or with a cable, he said also that I don't have the ehernet controller network controller PCI Device and SM Bus controller drivers

  If you can borrow an internet friends, you can download the drivers, to transfer them to a Flash DRIVE or a CD.  Without network drivers, you cannot connect to the internet.

• Connected to the internet, but not connected network magic shows

  My network is connect to the internet, both wired and wireless. On the compputer connected by magic cable network shows not connected, but I am connected. Unable to print remotely. Router shows connected but the network card is not.

  Thank you

  After reading your response, I decided to uninstall and reinstall the program. Thought it would be a little easier. I felt that the problenm was that the program had been damaged but hesitate to reinstall it because I downloaded from the internet several years ago and could not find the product key.  I finally found the program cisco and the location of the key and now works. Not as sexy but effective.

  Thank you once again

• GarageBand looking not connected network drive

  When I take my laptop away from my network home and open Garageband, it takes a long time to open and then gives an error message saying that it cannot find a NAS drive (which is installed in my home network).

  If I hit OK, then I can use Garageband, but if I try to use sharing, or even if I just mouse over the menu item from action, the application gives me the rotation beach ball and finally the message again that it can't find the network drive appears. It is almost impossible to export the song because when I click to dismiss the pop-up message, the drop of share also disappears.

  I don't know why Garageband is looking for the network drive. I tried the sacking of preferences and restart; I even uninstalled Garageband and reinstalled (when I wasn't home).

  Of course, when I'm home and can access the network drive, this happens. But it's very embarrassing when I record somewhere else.

  It's something to do with my user, because if I log in with a different account, the behavior occurs.

  Help?

  GarageBand 10.1.0

  When I take my laptop away from my network home and open Garageband, it takes a long time to open and then gives an error message saying that it cannot find a NAS drive (which is installed in my home network).

  GaregBand seeks always to open the last project that you opened.

  When you are not connected to the NAS server you use at home, try to launch GarageBAnd by double clicking on a project that is on your local drive.

• Win 7 Pro 64 bit configuration network, cannot access card reader when im not connected network

  IM under Win 7 Pro 64 bit on my laptop, im am Setup on an Exchange to my office network. The laptop has an SD card reader, and since I use CF cards I have a USB card reader also (my old card reader has been pre Win 7, so in desperation, this last weekend, I bought a new Targus card reader that preload drivers and is Win 7 compatible.

  The question is when im not connected to my office network and I put an SD card in the embedded player, or use the USB drive (the old drive did the same thing if it is not a drive issue) the computer laptop reconizes the event by sound in my computer scans the URL bar, and the card will not appear in the my computer window. So im hooked on my network it readings, launches autoplay and wonder what to do (as I have it setup to do).

  I always perform software updates and just checked my Windows is up-to-date.

  Any ideas as to what is happening and how to fix?

  Thank you

  Hello

  I suggest you to send your request to the below thread to get assistance on this issue.

  http://social.technet.Microsoft.com/forums/en-CA/categories/

  It may be useful

• No sound from the TV using a HDMI cable not connected to the laptop ASUS G75VW.

  I have an ASUS G75VW, when I connect the HDMI to my TV, I get only audio through my computer laptop speakers or headphones, while it is plugged.  In addition, the TV picture is only 480 p.  When I check the sound icon, it shows that the HDMI port is "not connected" even though it is.  I tried to uninstall and reinstall the driver on both the NVIDIA site and the site of ASUS.  Same question.  Help, please!

  Hello

  Make sure that it has the TV volume.

  You can also make sure that the connections are appropriate. Try to connect to another HDMI port as well.

  Refer to the section: "Check if the cables are connected correctly" and set the HDMI audio device as the default value.

  No sound in Windows
  http://Windows.Microsoft.com/en-us/Windows/no-sound-help#no-sound=Windows-8&V1H=win8tab2&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I also suggest you to consult the steps mentioned by "Karthik Vengaloor responded on 14 January 2013" and perform useful methods.

  Reference:

  Windows 8 audio via hdmi on desktop cable

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-pictures/Windows-8-audio-through-a-HDMI-cable-on-desktop/79aaa786-8311-4FA2-8206-0e57b8861baf

  Hope this information helps. Response with status so that we can help you.

• Printer Envy 5530: why I can not connect my Macbook on this new printer? Download HP and Apple and disc. NO.

  My HP Envy 120 died today after only 13 months. Bought the 5530 want to replace. My Macbook running lion 10.7.9 impossible to install the software of Apple, HP or the disc drive. Please someone tell me what to do. It seems crazy that each site recommend one for download. If the download n 't possible that they would be kind enough to give me an error message. life is too short for all that. Have installed ink cartridges, but will be back tomorrow if I can't make it work. Need a printer! Thank you very much for ANY help! Very grateful in advance.

  Hello @Islandedisto,

  Welcome to the Forums of HP Support!

  I would like to help you today with the installation of your new HP ENVY 5530 e-all-in-one printer on your Mac OS X 10.7. There is a chance that the old remains of your HP Envy 120 drivers cause a conflict when you try to install this new printer Envy. Can I please have you follow the steps below to solve these conflicts to occur.

  Step 1: Resetting the printing system:

  To begin, I will have you reset the printing system on your Mac because it is important that we have a pleasure to work with for troubleshooting clean slate. Please click herefor instructions on how to perform the reset. When the website opens, follow the steps under 'Reset the printing system in OS X Lion'. This Reset deletes each printer on your Mac. However, it does not uninstall printers. Therefore, if use you other printers on the Mac, once the reset is complete simply make sure printers are attached via a USB cable or connected network and (+) add hide them in. do not add your HP Envy in at this time.

  Once the reset is complete, proceed to the next step.

  Step 2: Uninstall the drivers and software:

  Please click here to find out how to properly uninstall your printer. Once the site opens, select the drop-down menu 'Mac OS X v10.6, OS X v10.7, OS X v10.8 and OS X v10.9' and follow the steps to complete uninstallation. This should clean up any software and drivers for your old HP Envy 120 institutions.

  Once the uninstall is complete, please continue on.

  Step 3: Check and repair your Mac disk permissions:

  1. Open Macintosh HD and go to Applications
  2. Go to the Utilities folder
  3. Open disk utility
  4. Select the hard disk volume, you use (usually on the left)
  5. Select verify disk permissions
  6. Once this process is complete, select repair disk permissions

  Step 4: Check the Apple updates: 

  1. Go to the Apple
  2. Select System Preferences
  3. Select software update
  4. Click update now
  5. Install your available updates
  6. Computer restart

  Step 5: Install the drivers:

  1. Please click here to download the latest full-function software package and the driver for your printer
  2. Once the site opens click on the download button at the top left
  3. Once the download is complete, follow the steps on the screen to install your new HP Envy

  Once installed successfully, your HP Envy, please try printing and scanning to ensure the full functionality of the product.

  Please reply to this message with the result of your installation. I look forward to hear from you!

• HP Photosmart 309 a will not connect to Yosemite 10.10.3

  I can not connect my laptop now my iMac to the printer via WiFi

  Hello @Berda37,

  Welcome to the Forums of HP Support!

  I understand that you are having problems when you try to install your printer wireless HP Photosmart Premium Fax all-in-One C309a on your computer Mac OS X 10.10. I would like to help you today with this problem of connectivity and installation. To start I have to check if your printer and your computer are actually "talk" to each other on the mobile network of troubleshooting. Once we check whether they are really communicate that we will be able to work towards a resolution. Can I please you follow the steps below.

  Step 1: Check of connectivity:

  1. On the front panel of your HP Photosmart press device button Setup (key)
  2. Press the right arrow next to the OK button until you see network
  3. Select OK in the network
  4. Under the menu network select OK in display network settings
  5. Select OK in the wireless summary screen
  6. Take note of The IP address and network name (SSID) that display
  7. On your Mac, check in the upper right corner, and then make sure your Mac is connected to the same network name (SSID) to which your printer is connected to
  8. Once you have verified that your Mac and your HP Photosmart camera are connected to the same network, please open the internet browser on your Mac
  9. In the address bar of you please enter the IP address that brought together you off the printer. Do not include the www.
  10. Search this site
  • If a Web site for your printer opens correctly: This proves with 100% certainty that your printer and your computer are 'talk' on the wireless network. Please continue with the steps below to install your Photosmart wireless successfully.
  • If a Web site for your printer does not open: This indicates that your printer and your computer communicate wirelessly. Please, do not continue to troubleshoot at this time.

  Step 2: Reset the printing system:

  To begin, I will have you reset the printing system on your Mac. Please click herefor instructions on how to perform the reset. When the site opens, follow the steps under "Reset printing in OS X Lion system" because the steps are the same for Mac OS X 10.10. This Reset deletes each printer on your Mac. However, it does not uninstall printers. Therefore, if use you other printers on the Mac, once the reset is complete simply make sure printers are attached via a USB cable or connected network and (+) add hide them po do not add your HP Photosmart into the computer at this time.

  Once the reset is complete, proceed to the next step.

  Step 3: Uninstall the drivers and software:

  Please click here to find out how to properly uninstall your printer. Once the site opens, select the drop-down list 'Mac OS X v10.6, OS X v10.7, OS X v10.8 and OS X v10.9' and follow the steps under two method to complete uninstallation.

  Once the uninstall is complete, please continue on.

  Step 4: Check and repair your Mac disk permissions:

  1. Open Macintosh HD and go to Applications
  2. Go to the Utilities folder
  3. Open disk utility
  4. Select the hard disk volume, you use (usually on the left)
  5. Select verify disk permissions
  6. Once this process is complete, select repair disk permissions

  Step 5: Manually install the driver Package:

  Please click here to manually download the package from Apple to HP v3.0 printer driversupdate. Once the site opens click on the download button at the top. Follow the instructions on the screen to install the driver package.

  Step 6: Check the Apple updates:

  1. Go to the Apple
  2. Select System Preferences
  3. Select software update
  4. Click update now
  5. Install your available updates
  6. Computer restart

  Step 7: Add the device:
  

  1. click on the menu of Apple , then Preferences System.

  2. click on Print & Scan and then check if the name of your printer appears in the printer list.

  3. click on the name of your printer, click the sign minus (), then remove the printer.

  4. click on the plus sign (), click Add a printer or a Scanner, click the name of your printer.

  5. click on the area of use or with the help of Print and then select the name of your printer on the shortcut menu. Ensure that the Photosmart driver is selected.

  

  6. click Add to add the printer to the list.

  -Source

  Once your printer is properly added to your Mac, please test the machine to check that everything works as it should.

  Please reply to this message with the result of your troubleshooting. You can also click thethumbs up' ' icon below to say "thanks for the help!" I can't wait to hear strings attached good luck!

• Interruption of the WiFi connection.  Green light is the Airport Express. Settings Network said the cable for the Wi - Fi connection is not connected or the device at the other end does not respond.

  Interruption of the WiFi connection.  Green light is the Airport Express.  Settings Network said the cable for the Wi - Fi connection is not connected or the device at the other end does not respond.  Tried to reset Airport Express, but remained light amber or orange flashing.  I unplugged it and waited and plugged back into the light turned green.  Rebooted computer (Mac Pro). Parameters of said the same thing.  Managed to create a WiFi "network with the ethernet in the network settings section, and yet I am wireless.  I am online but not wired and WiFi settings still says not connected, and either the cable for the Wi - Fi is not plugged or the device at the other end does not respond. I don't understand this situation.  My original WiFi name disappeared.  How I am on the internet?

  What is the brand and model of the modem Internet you have the AirPort Express directly connected by Ethernet? What exact model number is your Express?

• You are not connected to the internet! You want to work offline or try again? There is also a box with a red x and the message reads unplugged network cable.

  Unplugged network cable?

  Recently I get this message then on the line. You are not connected to the internet! You want to work offline or try again? There is also a box with a red x and the message reads unplugged network cable. It is very aggravating. Can someone tell me how to solve this problem? It might have something to do with my firewall? I recently downloaded mozzilla firefox if I could play words with friends, because IE would not work on the game.

  Hi LouisteanGriffin,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not persist in SafeMode with network, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 2: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3: Follow the steps in the article.

  How to troubleshoot a network home in Windows XP

  Windows wireless and wired network connection problems

  For reference:

  How to reset the Protocol Internet (TCP/IP)