Calendar cards Gets the wrong location

Similar Questions

• SMU-8431/8 RS-422 serial card sends the wrong number of bits

  I use a card series SMU-8431/8 RS-422 configuration for talking to a camera that has the speed of transmission parameters following 38400, 7 data bits, 1 stop bit, odd parity. I confirmed that the device certainly has these settings I can communicate with him using a separate Linux PC.

  When I try to use the serial port of EITHER the device does not react. Then, I connected the serial port OR on my Linux PC to see which sent the port NO. It is garbage. Nonprinting characters, control commands and the other characters are converted (for example I send the ascii character '1' and get the ascii character 'a').

  I made sure to add the terminating resistor 120 ohm NI RX + RX-lines and as mentioned in other posts on these forums, but it is only for the reception and did not solve the problem.

  I put a scope on the TX + and TX-lines from the map OR track seems reasonable that sent bits is correctly 38400 and voltage levels are correct moving between +/-3V. What I've noticed, is that the map series, NEITHER seems to be send to the 11 data bits. I expect 10-bit (1 start bit, 7 data, 1 parity, and 1 stop). I changed to 8 and then 6 bits of data and the total number sent passes to 12, then 10, respectively.

  I get the same behavior if I use Labview screws, Panel VISA for the port of MAX, or to remove the software NOR entirely and use Hyperterminal. This would seem to indicate that the problem is something in the settings of low level on the card itself.

  I tried a second SMU-8431/8 card and the same results, this isn't a fault map (may be two defective cards, I guess!).

  Any ideas?

  Many thanks in advance,

  Ian

  Discovered it was: used a scope to view the track both the Linux PC and the serial port OR to compare. The trace OR was significantly longer than the Linux. When I measured the width of the track OR whole, it worked to have a frequency of about 33 000, or much less that the 38400 assigned him. I was getting the wrong characters every bit of data from the port because NEITHER was out of sync with the Linux PC.

  I increased the port baud rate NOR and found that setting in 45 000 made it align correctly the Linux PC and I now the communication between the two devices.

  For the record, I don't have the terminating resistor 120 ohm or the anchor line to be included in the cable series between ports OR and Linux.

• Impossible to update the details of credit card, get the PMT_000008 error message

  Impossible to update the details of credit card, get the PMT_000008 error message all the time

  Is this another card or the same card but with slightly different details? (As the expiration date).

  Manage your Adobe Creative Cloud membership (Use the link 'Contact us' at the bottom, bottom right.)

• I have a Firebird database that points to the wrong location

  I have a Firebird database located on place on my machine, it is oriented in the wrong place and I do not know where to configure it so that it points to the location correct errors in events with event ID 33 Viewer then gives the following message

  Firebird errors: the "C:\WINDOWS\SYSTEM32\PING" database access is denied by the server administrator

  I would like to help on that

  Sorry, but if you are referring to Firebird http://www.firebirdsql.org/ then it is not a product www.mozilla.org or project.

  http://www.firebirdsql.org/en/support/

  The Firefox web browser called Firebird a short while eleven more years when the browser is at version 0.6, 0.7 and then 0.6.1 name it already changed for Firefox to version 0.8 because of this software of database Firebird with Firebird name and to avoid any confusion.

• get the 8900 location

  Hello!

  I try to get edge location 8900 (os 4.6). What is the most appropriate time-out period to get the location?

  Please, share your experience in this field...

  It depends on what type of criteria you are using. A standalone solution may take 3 minutes or more.

  Did you read the documentation for reference on the use of GPS?

• Cannot get the cell location is some devices?

  Hello

  I have problems with the location of the cell to get woithout GPS but the LocationProvider instance is always null.

  I use this criterion:

  ---------------------------------------------------

  Criteria = new Criteria();
  criteria.setHorizontalAccuracy (Criteria.NO_REQUIREMENT);
  criteria.setVerticalAccuracy (Criteria.NO_REQUIREMENT);
  criteria.setCostAllowed (true);
  criteria.setPreferredPowerConsumption (Criteria.POWER_USAGE_LOW);

  ---------------------------------------------------

  Get the location provider:

  ---------------------------------------------------

  LocationProvider locationProvider = LocationProvider.getInstance (criteria);

  ---------------------------------------------------

  is ALWAYS null.

  I check in a bold 9000 and a curve 8900and after seeing this page...

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800332/800703/What_Is...

  ... I think it's impossible, isn't it?

  Otherwise, I have another solution that is to ask the id from cell to opencellid webservices, but it is very inaccurate.

  any idea?

  Thank you.

  Here is a link

  http://press.rim.com/release.jsp?id=2710

  The credit goes to Mark.

• How to get the current location in the event thread?

  Hello!

  Can U pls tell me how to get the location where the thread object, it is in method() execution of MenuItem. PLS, tell me-

  I also used the different thread for the getLocation() method. But I do not have the coords of geo location...

  PLS, suggest me-

  My code is as below:

      private MenuItem getGeoCodes=new MenuItem("Current Coords",100,1){
  
                               public void run(){
                                   double[] coords=getLocationCoords();
                                   this.wait(12000);
                                   System.out.println("Latitude :"+coords[0]+" "+"Longitude:"+coords[1]);
                               }
  
                   };
  
      private double[] getLocationCoords(){
          Criteria criteria = new Criteria();
          criteria.setHorizontalAccuracy(500);
          criteria.setVerticalAccuracy(500);
          LocationProvider locationProvider = LocationProvider.getInstance(criteria);
          Location location=null;
          new Thread(){
             public void run(){
                     locationProvider.getLocation(60);
             }
          }
          QualifiedCoordinates qualifiedCoordinates=location.getQualifiedCoordinates();
          double[] coords=new double[]{qualifiedCoordinates.getLatitude(),qualifiedCoordinates.getLongitude()}   ;
           return coords;
      }
  

  But I myself NullPointerException. Coordinates get successfully, if we run the location capability in different function, rather than the event thread.

  Please help me-

  In my opinion, which may be too complicate things a bit. I think he's trying to do is register a LocationListener with his object of LocationProvider. Callback methods, send a message to the UI event thread as follows (no need to spawn threads):

  UiApplication.getUiApplication().invokeLater( new Runnable() {
      public void run()
      {
          // This code will execute on the event thread
      }
  });
  

  EDIT: If your interval is short, you can consider implementing this executable as a class and store an instance in the front.

• Firmware Flash HP LJ 8150N in the wrong location

  Hello

  I'm new here.

  I recently bought new ram for my printer and I didn't really know what to replace in the memory locations.

  So I removed the 8 MB out of the slot flash flash firmware and put 64 MB of pc100 in her memory. and then I put the 8 MB of flash in the last slot (D6 or D7).

  I don't know what to do. I saw the manual for adding ram at the end.

  Now, the printer hangs at startup. I don't know what to do.

  Can someone help me please?

  First replace the original 8 MB flash memory chip in the appropriate slot. Leave out any extra ram you put in but replace any ram that was originally in the printer. See if it starts, and if not what message or items you have on the screen? It could be as simple as the memory that you are trying to add is not good.

• I get the wrong function (0 * 80070001) when trying to complete pc restore and then stop errors prices 0 * 000000F4, 0 * 00000003, 0 * 8F59E9F8, 0 * 8F59eB4 0 * 8545B 710

  I am running windows vista and when he began the download of an update that it crashed and now when it turns on, I get the blue screen. After trying to repair it using the wizard, he finds nothing, so I try to the motor pump reinstall my computer from scratch disks but just comes up with an error immediately. also, I tried using f8 when it lights up and the attempt to restart from the last successful boot but this also fails and also turn off automatic restart after that accident fails please help.

  Hi paulspeedgun,

  Blue screen errors you get point of hardware failure or an incompatible driver. Have you recently installed a new hardware?  Below are troubleshooting steps to resolve your problem. Try each method until your problem is solved.

  -Disconnect all hardware devices on the computer and then restart to see if that solved the problem.

  -Restart your computer and immediately press theF8 key until you reach the Advanced Startup Optionsmenu.  In the menu, select Safe Mode and perform a System Restoreto restore your computer to a date prior to this issue.

  -Restart your computer and immediately press theF8 key until you reach the Advanced Startup Optionsmenu.  In the menu select Safe Mode with command prompt , type chkdsk /r to check the integrity of your hard drive.  Make sure you have all the important data to backup to a backup.

  -Insert your Windows disk and restart your computer from the disk. Clickrepair your computer, Next, select the operating system you want to repair and clickNext.  Select The Windows Memory Diagnostic tool to check the consistency of your memory. Let this test for a few hours for best results.

  Dena
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Get the former locations of the data files and Redo logs

  Version: 11.2
  Platform: Solaris 10
  
  When we manage hundreds of DBs, we do not know the locations of all DB files these allows DBs. say a DB goes down and you have all the required RMAN backups.
  
  When you restore the DB in a new location in the path of the new server, you must run the commands for the data files and ORLs below. But how do we know
  
  The former location of the data files.
  
  B. the old location of redo online stores that I can run
  
  run

  alter database rename file 'oldPath_of_OnlineRedoLogs' to 'newPath_of_OnlineRedoLogs' ;  --- Without this command , the restored control file will still reflect the old control file location

  run {
  set newname for datafile 1 to '/u04/oradata/lmnprod/lmnprod_system01.dbf' ;
  set newname for datafile 2 to '/u04/oradata/lmnprod/lmnprod_sysaux01.dbf' ;
  set newname for datafile 3 to '/u04/oradata/lmnprod/lmnprod_undotbs101.dbf' ;
  set newname for datafile 4 to '/u04/oradata/lmnprod/lmnprod_audit_ts01.dbf' ;
  set newname for datafile 5 to '/u04/oradata/lmnprod/lmnprod_quest_ts01.dbf' ;
  set newname for datafile 6 to '/u04/oradata/lmnprod/lmnprod_yelxr_ts01.dbf' ;
  .
  .
  .
  .
  .
  }

  Hello

  With the help of Oracle 11.2, you can use feature 'set newname for database' using OMF.

  SET NEWNAME FOR DATABASE TO '/oradata/%U';
  RESTORE DATABASE;
  SWITCH DATAFILE ALL;
  SWITCH TEMPFILE ALL;
  RECOVER DATABASE;
  

  After the restore and recover databases (i.e. before resetlog open) you can do to rename redolog. Just a query column member from v$ logfile and deliver ' alter database rename file 'oldPath_of_OnlineRedoLogs' to 'newPath_of_OnlineRedoLogs ';

  When we use the DSO is much easier to use OMF because Oracle automatically creates the directory structure.
  But when we use the file system that the OMF does not serve due DBA dislikes system generated on file system names.

  If you don't like OMF file system, you can use the script on thread below to help restore you using readable for datafile names, tempfile, and redo.

  {message: id = 9866752}

  Kind regards
  Levi Pereira

• Get a wrong location in blackberry GPS

  Hello

  I developed a blackberry based GPS application. When I use this app on road in the clear sky, a few times it gives me before my location. As a result, I get wrong on google map.

  Help, please.

  Thanks in advance.

  I guess that's probably pretty specific to your application.

  However, if you take (for example) a reading every 10 seconds and you get a reading that is 10 miles from your last known location, so of course, this location must be discarded.

• Get the GPS location API error - provider is not available

  Hello

  I am trying to access the information of location using Android location API (via LocationManager.GPS_PROVIDER), but without success. I get error "provider not available."

  AndroidManifest.xml has lines related to the relevant permissions:

  
  

  But I do not get prompt the same security to grant these permissions to my request.

  OS version 2.0.0.3894

  Build 73070

  Thank you.

  I solved this problem by restarting and place the device near a window.

  What I was wondering now is why Android player never asked security permission to access the location of the GPS. What is a function of development?

• ask Firefox to remember the password if I get the wrong password

  When I try to connect to my gmail and give the correct password, firefox asks me to save him.

  But if I give a wrong password ask me and save it.

  What is going on? any help please?

  You can check the presence of multiple, case, versions of this name and password and for entries with an empty name.

  • Tools > Options > Security: passwords: "saved passwords" > "show passwords".

  You can delete all data stored in Firefox with a specific area through "Forget this Site" in the context menu of a history entry ("" history > view history "or" view > sidebar > History "") or via the subject: permissions page.

  Using "Forget this Site" will delete all data stored in Firefox in this area as bookmarks, cookies, words of past, cache, history, and exceptions, so be careful and if you have a password or other data from that domain you don't want to lose then check that back up these data or make a comment.

  You can't recover from this "forget" unless you have a backup of the files involved.

  It has no lasting effect, so if come back you on such a 'forgotten' site, then the data of this Web site will be saved once more.

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem.

  • Put yourself in the DEFAULT theme: Firefox/tools > Modules > appearance
  • Do NOT click on the reset button on the startup window Mode safe
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

  There are other things that need attention.

  The list of details of the system indicates that you have an old version of Flash 11.4 r402.

  1. Shockwave Flash 11.4 r402

  You can find the latest versions of Flash player for Firefox on this page:

  • http://www.Adobe.com/special/products/flashplayer/fp_distribution3.html

• Why is it I can not connect my IPad to bigpond ADSL. The message I get the wrong password?

  I've been using the named password: the homegroup password?

  I've been using the named password: the homegroup password?

  Hello

  You might get a faster response in the following forum.

  Apple - Support - iPad:
  http://www.Apple.com/support/iPad/

  Concerning

• Get the current location of the user.

  I want to create an application in which the current position of the user should be displayed. Can someone tell me the logic (connection only part) If cannot tell the code...

  And here are some others:

  http://supportforums.BlackBerry.com/T5/Java-development/simple-location-API/Ta-p/1145951

  http://supportforums.BlackBerry.com/T5/Java-development/location-APIs-start-to-finish/Ta-p/571949