Calibrate the IMU to any desired level/executive aircraft

Similar Questions

• Hi, I have a sport IWatch found that domestic activity (usually running on treadmill) there is a huge different iWatch see the short distance (approximately 23%) then the treadmill Distance (I used several treadmills). Calibrate the iwatch outside.  any o

  Hello

  I have a sport IWatch found that domestic activity (usually running on treadmill) there is a huge different iWatch see the short distance (approximately 23%) then the treadmill Distance (I used several treadmills). Calibrate the iwatch outside.

  no possibility to calibrate domestic? or solution of New York.

  Thank you

  Avner

  Hi Avner

  Currently, there is no way to calibrate Apple Watch on a treadmill.

  Calibration teaches your watch how your arm movements relate to your length of stride at different speeds when walking you and/or running. It does this by comparing the accelerometer data with GPS (location services) data from your iPhone. To optimize the performance of the application of the workout, when using the treadmill, allow your arms swinging naturally.

  It can help restore your calibration data and start over:

  On your iPhone, in the application of the watch, go to: My Watch (tab) > privacy > Motion & Fitness > tap reset Calibration data.

  To calibrate again, follow the instructions in the article to support below, including:

  • Records open-air market training and/or run in the open air with the application of the workout on your watch.
  • This for 20 minutes at each speed to during which normally walk you or run.
  • While doing so, take your iPhone with you, with location on Services.
  • Allow your arms swinging naturally during training.

  Estimates of activity also dependent on your personal information. To verify that it was entered correctly and update over time:

  -On your iPhone, in the application of Eve, go to: Watch My > health > edit (top-right).

  More information:

  Calibrate your Apple Watch for better accuracy of training and activity - Apple Support

  Use the activity on your Apple Watch - Apple Support

  Use of the workout on your Apple Watch - Apple Support

• I can no more color calibrate my monitor Apple Cinema Display 10 years because it is more compatible with my iMac Thunderbolt.  How can I color calibrate the Apple Cinema Display Monitor?

  I currently own an iMac OS X El Capitan Version 10.11.4 27 inches (2 1/2 years) with Thunderbolt technology.  I also have a screen of cinema with older technology.  Previously, when the technology was the same for the Apple display and my previous iMac, I was able to color calibrate the Apple cinema and my iMac but it is no longer the case. I know that there is a way to color calibrate the monitor Cinema with old technology when the iMac has the Thunderbolt technology, but cannot remember what are the steps.  The colors on the Apple Cinema are out of whack and too bright.  Can anyone help?  I'd appreciate any help you can provide.  Thank you.

  Henriette

  PS: The color calibration device I own is a gretagmacbeth eye - one display2.

  Hello henriettefromnovato,

  Thank you for using communities of Apple Support.

  I see you want to calibrate the color of your movie screen.  You can calibrate your screen by following the steps in the link below.

  OS X Yosemite: calibrate your screen

  If you are unable to do so, then please be more specific about what happens when you try and calibrate.

  Have a good.

• My Apple Watch will not charge on the charger.  I cleaned the back of the watch and the charger.  Any ideas?

  My Apple Watch will not charge on the charger.  I tried to clean the back of the watch and the charger more used several points of sale, but in vain.  Any ideas?

  Hello

  When you reload your watch, check that:

  • All the plastic film was removed from both ends and both sides of the cable support (consult closely on the head of the charger).

  

  • On the back of your watch and the head of the charge cable are clean and dry (clean with an abrasive, lint cloth).
  • The head of the load is properly aligned with the back of the watch, with the concave side / curve touch fully:
    • Some docks of watch, brackets, cases or protectors might hinder it.
  • You use a real Apple magnetic Charging Cable or a certified Apple module magnetic charge.
  • If you reload your watch by plugging into a power outlet:
    • Check that the magnetic charge cable Apple USB connector is fully engaged in the USB power adapter.
    • Try to use different maps of the following:
      • The real Apple USB Power Adapter that came with the watch, or;
      • A true 5W Apple (iPhone) or 12W (iPad) USB power adapter, or;
      • A third-party certified 5W (MFi) Apple USB power adapter.
    • Try to charge via a USB port (see following).
  • If loading via a USB port on a computer, make sure that you use a USB 2.0 or 3.0 port, the computer remains turned on and awake, and the cable is plugged directly into the computer (not on, for example, an external keyboard).
  • If your battery is very low, you may need to wait a few minutes for the green lightning appear (confirming that the charge has started).

  Once the load has started, you can tap on the screen at any time to check the progress (leave a few minutes at the beginning, where the watch is in charge of a very low battery level). A green lightning bolt symbol indicates that your watch is being loaded. It is normal the screen back to sleep while continuous load.

  More information:

  Check your battery and load your Apple Watch - Apple Support

• Calibrate the Panel 2 on Libretto W100

  My knowledge and my ability as a manager should mean that this issue is a no-brainier, but he beat me!

  The second (lower) Panel of my W100 needs to re - calibrate, but I can't convince the device to do. I consulted * Tablet PC settings * and I tried * calibration *-it allowed me to calibrate the display panel 1 (top) perfectly. With the 2nd group, trying to tap the cross produces the usual sound and the circle where my finger pressed, but he would not recognize the "tap." The only option was to support on * Esc * to exit.

  When you try * installation * (in * Tablet PC settings *), it seems that the device cannot deal with the idea of having to support on * entry * continue - be it on the virtual keyboard or a USB device. Accordingly, it is not possible to precede real calibration screen (even if I can get beyond the command "Touch this screen to identify it as the touchscreen".)

  Two touchscreens are working perfectly, the works of virtual keyboard perfectly on both panels... it's just that the calibration process will only allow me to calibrate panels 1 and not 2 (even though I chose the Panel 2)

  Y at - it a secret that I am not deprived?

  Any help would be much appreciated.

  Hello

  Can you please try this method for calibration of the Panel:

  Tap 0) set it to zero, if the calibration data has been backed up.
  (1) 1 select. Inner cover of Toshiba 1024 x 600
  (2) calibrate
  (3) select 2. Inner cover of Toshiba 1024 x 600
  4) press reset
  (5) re - select 2. Inner cover of Toshiba 1024 x 600
  (6) calibrate
  Calibrate 7) is fine. (16 points of the cross)

  Please send comments.

• Calibrate the compass of the iPhone?

  I have a new iPhone OS (iOS 9.3). According to Google Maps, the streets of my neighborhood are perfectly North/South and East/West as close as my eye can detect, both within a few degrees maximum. But the compass in my iPhone shows them being about 15 degrees off the coast of true North or 30 degrees on the magnetic north. The magnetic declination at my location is about 15 degrees, it's consistent, but seems to be about 15 degrees off the coast.

  Is it possible to calibrate the compass of the phone? Or a compass of this kind is simply not terribly accurate? Or Google Maps is from afar? (The latter seems unlikely.)

  I found the web pages that talk about ball to do a bit of red to move around the screen, but I get only the ball. I tried to quit all applications, including the compass application and then launch the compass application, as suggested on one site, but I don't always get the red ball of calibration.

  What I am doing wrong? Or this version of automatic calibration and a little off?

  Thank you

  Calibration of the compass requires that location Services on. The phone detects if it is calibrated or not and will display the calibration screen if it is not.

  Rather than relying on Google Maps, get a real pathfinder compass and check the phone against it. Use the compass to draw a North-South line on the floor with chalk, away from any metal (including the iPhone), then check the iPhone against the line you drew.

• Satellite M40 does not seem to charge the battery beyond a certain level

  Just a brief explanation of my work.

  I make repairs pc and laptop, replacement of jack, BGA/brazing repairs etc.;
  However computer have always baffled me. I have a Toshiba M40, although I know that this problem is not specific to this model.

  The laptop does not charge the battery beyond a certain level at the moment its impasse on 41%, it says loading in windows but do not go anywhere.
  I saw other portable that stick onto the other percentages 99%, 70% etc.

  I tried to completely discharge the battery (on windows) and reload (for Windows), and also tried to unload and reload not in o/s, if anything they seem to have made things worse as initially the issue of charge level was approximately 50% and more.

  By mistake the laptop wasn't for awhile so the battery flat, which probably did not help as I understand its best to store 40% battery when not in use.

  Any ideas what the problem is and if theres any way to revive this battery?

  Hello

  In my opinion, the problem is related to the breakdown of battery.
  I'm don't know how old your battery is but eventually should be replaced.
  After a long period of use, the battery loses the own performance and must be replaced.
  This is nothing unusual and often to used batteries.

  Welcome them

• I6 fire babysit device when using the internet? any solution?

  I6 fire babysit device when using the internet? any solution?

  Let's define "overheating". If the temperature of the phone reached a dangerous level the phone turns off it to cool down. This phenomenon occur? If this is not the case it is not overheated.

  What is your cell signal? If the signal is low, the phone must increase its power to maintain a connection. This may require as much as 10 times the energy as a strong signal, and the phone gets hot under these conditions. If will also drain the battery very quickly.

• Z510 - calibrate the battery

  I have lenovo ideapad z510 i7. I want to calibrate the battery because it's showing the level of remaining battery bad

  Mod edit: System model added to the front of the subject line to improve visibility / clarity.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo is a newer version of the update to firmware battery listed above available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• What is the replacement for "configure Reference Levels.vi niScope.

  I just put my driver OR-Scope of 3.4 to 3.6 and now the VI, "set up reference Levels.vi niScope" is missing in the instr.lib\niScope\Configure\ directory. I found an old version under niScopeObsolete.llb but this version uses DLL calls where the 3.4 version used nodes of property. What became of this VI and where can I find a covering memo telling me that this feature has been removed?

  Thank you

  Charles

  Hi Charles,

  I looked back through the files on the disk and the oldest version I found this VI was about seven (can't find the files before this date) years ago. It was located under the folder \Measurements\Obsolete even at this time, and it seems to be the same VI (he calls in the DLL). The following year he then changed locations to the niScopeObsolete.llb directory. I was unable to find a version that contained simply property nodes, but you are right that the features are essentially the same. Actually, this is the most likely reason that it is not a top-level function that exists in one of pallets of NOR-SCOPE function, since it is only used in some measures specific and exact functionality can be achieved through the use of knots of property.

  You are able to make use of the current version you found in niScopeObsolete.llb or maybe just nodes of property without any problems? I'm interested in knowing what else was different with the 'new' version that you had with the nodes property. Is that what the icon and/or documents of the VI is different? Do you still have this VI you can join? I want to assure you that this change did not affect your application beyond the confusion to have the situation has changed.

  Kind regards

• How to calibrate the PCI-6110 with NOR-DAQmx

  Hello

  I am a new user of the PCI-6110 Council tries to run the calibration using LabVIEW procedure. I look at the document "Calibration" on the page of the manuals for the Board of Directors,

  http://sine.NI.com/NIPs/nisearchservlet?nistype=psrelcon&NID=11888&lang=us&q=FQL: 28locale % 3Aen % 29 + AND + % 28phwebnt % 3 A 1081 + OR + phwebnt % 3 A 7075% 29 + AND + 28nicontenttype % 3Aproductmanual % 29 + AND + % 28docstatus % 3Acurrent % 29% 20RANK % 20nilangs: en & title = NOR + PCI-6110 + manual

  One of the first steps in the document is to call the AI_Configure command to set the input mode, beach, etc. I'm using LabVIEW 8.5 with the NOR-DAQmx software, and I can not find the command (which, in LabVIEW, seems to be "AI Config.vi") anywhere. The calibration paper was written in 2003, and I gather from Google searches (please, correct me if wrong) that this command is actually a part of NOR-DAQ traditional, who was replaced by driver OR DAQmx.

  My question is this: what is the equivalent to AI_Configure command in the latest software? Is it perhaps a subsequent document describing how to calibrate using NOR-DAQmx?

  Thanks much for any help.

  Tom McLaughlin

  Hi Tom,

  The calibration Procedure series B, E, M, S, which is also linked from this page, describes how to calibrate the PCI-6110 with NOR-DAQmx.

  Brad

• Can not calibrate the battery because the battery is not. HP hdx 18

  I need to calibrate my new battery (based on the verification of the system), but I can't get the battery to charge. Is there another way I can calibrate the battery?

  Hi Brian,.

  What operating system is installed on the computer?

  The problem occurs if the battery is faulty.

  Method 1: Check the links below, if you have Windows 7 or Windows Vista.

  Solutions to common battery problems (Windows 7)

  Solve battery problems (Windows Vista)

  Method 2: If the problem persists, you should contact HP support for assistance.

  http://h10025.www1.HP.com/ewfrf/wc/siteHome?cc=us&LC=en

  Answer please if you have any questions.

• Cannot display the properties of Amplitude and level controls

  I'm new to LabVIEW and just installed ver 8.6 on my machine. When I open the TutorialGenAnalyzeDisp1.vi, the run button is disabled. When I double click on the Amplitude and measures of level, I get a dialog box says "cannot display properties. If I click on the run button, I get an error message: "errors of block diagram / Subvi 'Amplitude and level measurements': Subvi is not executable."

  I have the LabVIEW base development system. Is it possible that I don't have that element in my library or an installation problem? I look forward to re - install LabVIEW. It took over 3 hours to install.

  Hi jdai

  The Amplitude and the level of the Express VI measures is included in LabVIEW complete edition and professional development systems, not in the database. So, as you think, you do not have some of the elements necessary for the execution of this VI.

  Best regards

  David

  NISW

• How to calibrate the sensor of gravity on Z3?

  My gravity sensor is a bit tilted, but I can't find anything to fix.

  There used to be a possibility to do it on some old phones Xperia, but it seems that this feature has been fully subscribed.

  Y at - it all posibliliy to calibrate the sensor of system level?

  @slj_zc

  You may need to stop by your local care of Xperia, based on your previous posts

  http://talk.sonymobile.com/T5/Xperia-Z3-compact/bounce-back-still-happening/m-p/936387#M7046

  http://support.sonymobile.com/global-en/contactus/

• calibrate the scanner c4180

  Hello

  There is a way to calibrate the colors on the HP Photosmart C4180 scanner? When I scan the black color of the original is read somehow blue o and all other colors are read with different colors.

  In the Toolbox of the printer when I hit the button for color calibration gave me an error on cannot be applied to the current configuration, but I tried different configurations without success.

  There is perhaps a procedure to calibrate the colors but only the scanner? because the printer has the correct colors.

  I searched on google for more than a week for some advice without success.

  Thanks in advance for your help.

  Thanks for the reply. Now, this indicates that the hardware of the printer is down. I would contact HP support by phone to verify your hardware options. You can use this Web site for information about how to contact HP properly, based on your region: Contact HP worldwide

  Please let me know if you have any questions or concerns.

  Mario