Calibrate the NI 9265 cRIO module

Hi guys

I have a few output current modules NI 9265, analog and I would like to perform an external calibration using a digital multimeter to 8 1/2 available in the laboratory. I tried to do it using a MAX interface, but I discovered that it is not possbile because the analog module is installed in a cRio-9074 control. I don't have this controller and an EtherCat chassi to install modules. Is there another way to calibrate with DAQmx with the NI 9265 installed in the cRio control? Would it not possible in LabView?

Hey Lane,.

Unfortunately cRIO or EtherCat frame can be used with DAQmx since they do not belong to the data acquisition platform. Some (e.g., NI 9265) cSeries modules are supported by both platforms, but it can only be calibrated by a cDAQ platform.

If you check the manual for calibration for the NI 9265 (if you have not yet verified) you will see that it is recommended to use a cDAQ-9178, including a cDAQ chassis 8.

http://www.NI.com/PDF/manuals/372667b.PDF

If you really need an external calibration, please contact your local office of OR to get more information on calibration Services.

Best regards.

Tags: NI Hardware

Similar Questions

  • MAX does not see the cRIO modules!

    Hello

    I have a cRIO-9073 and C 3 (9401, 9239, 9263) modules installed in slots 1-3 respectivly. I can configure the chassis correctly upon arrival 2 months ago and I managed to acquire by a module 9234. Now that the 3 mentioned c modules arrived I installed and have a problem - MAX of nothingness, or analysis of LabVIEW RT engine cannot see modules. Attached are MAX.png and DiscoveryStatus.png that depict. NOR-RIO is version 4.00 and corresponding set is completely downloaded to the cRIO. I do not understand the concept of software cRIO yet but I'm positive, that is the same as used to work the first time that I had tried. The network is OK - host is 100.0.0.1, cRIO is 100.0.0.100 and they see.

    I susspected that perhaps specific drivers are needed for these particular C failet, but I can't verify that the status of software.

    Basic details to accept and understand the CompactRIO concept is spread across many different documents, and it's really hard for the newbees to grasp, so debug/fix situations.

    Does anyone have an idea what is causing my problem?

    Thanks in advance,


  • Calibration of the PXI - 2548 relay module

    #1) where can I find the date when my PXI-2548 relay module was first calibrated?

    (#2) y has different ways to calibrate this relay module and if yes what are?

    (#3) combien of time should this relay module be calibrated?

    Thank you

    Julian

    Hi Julian,.

    NI PXI-2548 requires no calibration because it does not all electronic components that can be calibrated.  Therefore, there is no calibration carried out, there is no way to calibrate the module, and there is no timetable for calibration.

    Note that you can compensate for the loss of insertion of the passage on a per path basis.  These offsets typically include loss through cables and are carried out when the Board is placed in the system.  It is more than compensation compensation for 'switches + connectivity' system rather than a Board calibration; It is dependent on the system.  I recommend you do this compensation measure before proceeding with automated tests.

    I hope this helps!

    Chad Erickson

    Switches Product Support Engineer

    NOR - USA

  • Repeated values in the measure (FPGA, cRio) signals

    Hello

    I'm seeing repeated in my measurements values and trying to determine the cause

    I read a single analog channel from a module NI 9201. In order to eliminate the noise, I averaged several samples by using the ms and RMS measures VI (shown in "FPGA Code.png")

    An example of repeated values appear in the "comparison of Signals.png' for both the original signal and mean

    The sampling frequency of the NI 9201 module for a single channel is 500 kech. / s, which I also checked by measuring the sampling frequency (the code for this is also reflected in "FPGA Code.png")

    On the target of cRIO RT I record these values in a loop timed 500us using 1 MHz of the cRio clock

    For the ms and RMS measures VI, I tried several options, for example:
    -500 US measurement time, sample rate 500 kech. / s
    -450 US measurement time, sample rate 450 kech. / s
    -400 US measurement time, sample rate 400 kech. / s
    -US 300 measurement time, sample rate 300 kech. / s

    Each of them give measurements with repeat values to varying degrees, for both original and average signals

    Any suggestions?


  • build books for Slot 1 cRIO module Profibus - FPGA, but fails to Slot 7

    We have a Profibus cRIO module installed in a chassis cRIO-9024 and difficulties during the process of generation FPGA. Construction is very well when the project is configured for the Profibus module in Slot 1, but it fails with errors in Code generation, when the project is configured to Slot 7. I created a very simple pair of projects (attached) which illustrate the problem.

    Error messages are "a generation of HDL code error has occurred" and "Terminal (to the) requiring a constant wired entrance to not constant or sources. A screenshot is included in the attachment.

    Commenting on the second sub - VI ' CS_cRIO_PBM [7] FPGA_SPI_ReadWrite.vi "in Profibus_Slot7.vi allows the FPGA code build without errors. Tried the constants of wiring for the Subvi entries and other variations, but still failed to build.

    I am aware that the documentation for the Profibus module recommends installation in Slot 1, but our client requires us to install in Slot 7.

    Someone at - it understand the generation of Code errors that I receive?

    (1) you use the old driver and this is expected behavior.

    (2) the new driver will allow you to put the module in any location. Be sure to leave an empty slot next to him due to thermal considerations.

  • Disappeared from the toolbar URL, and modules are not coming back.

    Hi people. Once more Firefox drives me crazy, I woke up this morning, turned on the old computer, Firefox has started, and I have no URL bar. I tried to restore it, but no luck. Been looking for the Firefox forums for a few hours, found similar questions, but... .no cigar. I have the version 36.0.4 of Firefox. Can someone please explain how he disappeared and how to get it back?

    I uninstalled FF, entirely. And re-installed. URL bar still to go. Also, I have connected to my SYNC, but my modules are not coming back.

    I would appreciate your help.

    You still have the Navigation bar visible with other buttons on the toolbar and tab bar?

    Make sure that you run not Firefox mode full screen (press F11 or Fn + F11 to toggle; Mac: Command + SHIFT + F).

    If you are in full screen view then hover over with the mouse to the top of the screen to facilitate the bar appear Navigation and tab bar.
    Click the expand (in the top right Navigation bar) to exit full screen or right-click on a space empty on a toolbar and select "exit full screen" or press the F11 key.

    Try to rename (or delete) the file xulstore.json in the Firefox profile folder.
    You can use this button to go to the Firefox profile folder currently in use:

    Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem.

    • Put yourself in the DEFAULT theme: Firefox/tools > Modules > appearance
    • Do NOT click on the reset button on the startup window Mode safe
  • How to display the bar of default modules at startup of firefox?

    I'm seeing the bar of default modules at the start of Firefox. How to do this? Every time when I run Firefox I have to go to open the Menu (logo) > > right-click > > Check Addon Bar. Is it possible to show by default?

    PS: It happens after updating Firefox 29.0.1

    29 Firefox no longer supports the add-on bar, then you must use an extension that adds this toolbar.

    This extension may not work properly if you need to re - activate the add-on on each start of Firefox bar, and you can try to use another extension that restores the bar of the add-on instead as the classic extension restaurateur theme has already been mentioned.

  • I can no more color calibrate my monitor Apple Cinema Display 10 years because it is more compatible with my iMac Thunderbolt.  How can I color calibrate the Apple Cinema Display Monitor?

    I currently own an iMac OS X El Capitan Version 10.11.4 27 inches (2 1/2 years) with Thunderbolt technology.  I also have a screen of cinema with older technology.  Previously, when the technology was the same for the Apple display and my previous iMac, I was able to color calibrate the Apple cinema and my iMac but it is no longer the case. I know that there is a way to color calibrate the monitor Cinema with old technology when the iMac has the Thunderbolt technology, but cannot remember what are the steps.  The colors on the Apple Cinema are out of whack and too bright.  Can anyone help?  I'd appreciate any help you can provide.  Thank you.

    Henriette

    PS: The color calibration device I own is a gretagmacbeth eye - one display2.

    Hello henriettefromnovato,

    Thank you for using communities of Apple Support.

    I see you want to calibrate the color of your movie screen.  You can calibrate your screen by following the steps in the link below.

    OS X Yosemite: calibrate your screen

    If you are unable to do so, then please be more specific about what happens when you try and calibrate.

    Have a good.

  • Calibrate the Panel 2 on Libretto W100

    My knowledge and my ability as a manager should mean that this issue is a no-brainier, but he beat me!

    The second (lower) Panel of my W100 needs to re - calibrate, but I can't convince the device to do. I consulted * Tablet PC settings * and I tried * calibration *-it allowed me to calibrate the display panel 1 (top) perfectly. With the 2nd group, trying to tap the cross produces the usual sound and the circle where my finger pressed, but he would not recognize the "tap." The only option was to support on * Esc * to exit.

    When you try * installation * (in * Tablet PC settings *), it seems that the device cannot deal with the idea of having to support on * entry * continue - be it on the virtual keyboard or a USB device. Accordingly, it is not possible to precede real calibration screen (even if I can get beyond the command "Touch this screen to identify it as the touchscreen".)

    Two touchscreens are working perfectly, the works of virtual keyboard perfectly on both panels... it's just that the calibration process will only allow me to calibrate panels 1 and not 2 (even though I chose the Panel 2)

    Y at - it a secret that I am not deprived?

    Any help would be much appreciated.

    Hello

    Can you please try this method for calibration of the Panel:

    Tap 0) set it to zero, if the calibration data has been backed up.
    (1) 1 select. Inner cover of Toshiba 1024 x 600
    (2) calibrate
    (3) select 2. Inner cover of Toshiba 1024 x 600
    4) press reset
    (5) re - select 2. Inner cover of Toshiba 1024 x 600
    (6) calibrate
    Calibrate 7) is fine. (16 points of the cross)

    Please send comments.

  • Calibrate the compass of the iPhone?

    I have a new iPhone OS (iOS 9.3). According to Google Maps, the streets of my neighborhood are perfectly North/South and East/West as close as my eye can detect, both within a few degrees maximum. But the compass in my iPhone shows them being about 15 degrees off the coast of true North or 30 degrees on the magnetic north. The magnetic declination at my location is about 15 degrees, it's consistent, but seems to be about 15 degrees off the coast.

    Is it possible to calibrate the compass of the phone? Or a compass of this kind is simply not terribly accurate? Or Google Maps is from afar? (The latter seems unlikely.)

    I found the web pages that talk about ball to do a bit of red to move around the screen, but I get only the ball. I tried to quit all applications, including the compass application and then launch the compass application, as suggested on one site, but I don't always get the red ball of calibration.

    What I am doing wrong? Or this version of automatic calibration and a little off?

    Thank you

    Calibration of the compass requires that location Services on. The phone detects if it is calibrated or not and will display the calibration screen if it is not.

    Rather than relying on Google Maps, get a real pathfinder compass and check the phone against it. Use the compass to draw a North-South line on the floor with chalk, away from any metal (including the iPhone), then check the iPhone against the line you drew.

  • Satellite Pro 4600 calibrate the battery?

    Hello

    My Satellite Pro 4600 battery is pretty weird. I always completely load to 100%. But when I use my laptop and it reached 60-65%, it goes down to 3% of the battery. Now, I was wondering if there is a way to calibrate the battery, so he sees it as a battery of 100% full again? Anyone who can help me?

    Thanks in advance

    Hey,.

    Tips for the battery charge.

    Unplug the computer from the power adapter and turn it on. Let the computer battery power until the computer turns off, indicating that the battery is fully discharged.

    Remove the battery.

    Using a soft cloth, wipe the battery packs connectors and AC adapters.

    Reinsert the battery.

    Plug the power adapter from the computer and check the wall outlet, ensuring that the connection is firm.

    When the PC is off, let the battery charge until the icon or the battery light turns green.

    Disconnect the power adapter.

    Remove the battery.

    Wait 30 seconds and reinsert the battery.

    Reconnect the AC adapter.

    Let the battery recharge until the battery status light turns green or the icon appears at 100%.

    Now your battery must be charged completely. Unplug the computer from the wall outlet and turn on the PC. You should notice more autonomy.

    See you soon

  • Firefox 4: how to display the list of installed modules

    Used to be that if you have clicked on the modules you see list installed and have asked specifically to look for new modules.

    Now by clicking on Add - ons takes you directly in the search of new modules.

    You say that when you click on Tools – Addons you don't have a list that says

    GET ADDONS
    EXTENSIONS
    APPEARANCE
    PLUGINS
    If you do click Extensions
    
  • Satellite C660 - 25 c - how to calibrate the battery

    Hello

    First of all, I apologize for my bad English.

    I would like to know the procedure to calibrate the battery of my Satellite c660 - 25 c.

    Thank you

    Sincerely, romat1993

    It's pretty easy.

    To calibrate the battery, it of necessary to charge the battery until the battery indicator indicates that the battery is fully charged.
    Then, unplug the AC adapter and keep the battery discharge until it s completely empty.
    Then connect the power adapter and charge the battery again.

    This procedure should be repeated two, three times in the line.

  • Satellite L30 - 10Y black at startup the screen upward after the installation of new modules of RAM

    Hello

    I use the L30 - 10Y model with the following memory specification:

    standard: 512 MB
    maximum scalability: 2 048 MB
    technology: DDR2 RAM (533 MHz)
    expansion module sizes: 256, 512, 1 024 MB

    I use Windows Vista Home Basic Edition with a 32-bit operating system.

    When installing, I removed the standard 512 MB module and added 2 modules of 1 GB compatible. At startup, it stays on a black screen.

    However, if I removed 1 1 GB modules and put the old 512 MB module to give me 1.5 GB, it works.

    I was wondering if anyone knows why this is and if there is anything that I can try to get the maximum of 2 gb, if it is indeed possible.

    Thanks in advance.

    According to the product page Toshiba Satellite L30 - 10Y is able to manage 2 GB of RAM (2 x 1 GB)
    I think that the problem is related to memory modules not fully compatible
    I think a new, fully compatible RAM modules should resolve this problem.

    PS: You updated the BIOS? If this is not the case, check if a new update of the BIOS is available on the European driver Toshiba page.

  • How to calibrate the heart rate monitor?

    How to calibrate the heart rate monitor that shows a too high concentration?

    Hello

    It is not possible to calibrate the heart rate sensor. However, various factors can affect the performance of the detector.

    During training, to optimize the performance of the heart rate sensor, ensure that you wear your watch fits on top of your wrist.

    Apple suggests that consider you the clamping Strip before starting a workout and it loosen again thereafter.

    The sensor is likely to give better results for the workouts that involve rhythmic (for example running) rather than the irregular movements (e.g., tennis). Other problems that can affect the performance of the sensor include the perfusion of the skin and wrist tattoos.

    More information:

    Your heart rate. What it means, and where on Apple Watch you will find. -Apple Support

Maybe you are looking for