Calibration SMU 4330 problem

Similar Questions

• SMU-4330 remote sense

  I'm trying to get the feeling of distance on the SMU-4330 to work. I have a sensor based bridge connected as shown in the manual. I can't find a property node for the remote sense. The remote sense works automatically when hooked or should it be set up?

  I thought about it.

  The 4330 do not correct the voltage at the bridge. They only correct the output of the sensor by the voltage sense lines back.

• Confusion about the Source of excitement in the bridge SMU-4331 input module

  Hello

  I had some confusion through the input of the bridge SMU-4331 sheet module.

  In the features section of excitement, its current Minimum as 29mA says. What it means. It can only current greater than 29mA delivery!

  

  I think this should me Maximum current specification.

  If you look at the table below

  

  350 ohm resistance, the current should be 10V/350 ohm = 28.5mA

  but for 1 K ohm, current will me 10V/1Kohm = 10mA, which isn't normal, if you specify current minimum as 29mA.

  any thoughts?

  Kind regards

  Mirash

  Hello Mirash,

  I'm glad I could help!

  As for your other question, the SMU-4330/4331 are inherently peripheral ratiometric.  This means that they are designed to detect the level of excitement and range of the ADC to the appropriate scale.  In this way, we can compensate for permanent changes in the voltage.  One of our engineers wrote a big article really nice area on the subject I would recommend that you take a look at: Sensors of Measuring Bridge-Based with the ratiometric approach

  See you soon,.

• Color calibration settings reset after restarting the computer

  Hello!
  I had a really hard time with my monitor calibration.
  I will try to describe my problem as simple as possible. I hope that someone will find a solution to this because I just couldn't.

  SYSTEM:
  ASUS N750JV, Intel Core i7, NVIDIA GeForce GT 750 M + Intel HD Graphics 4600 and, of course, Windows 8.

  PROBLEM:
  "Calibrate display" settings change/reset back from each time after restarting the laptop, shut down or put to sleep.

  DESCRIPTION OF THE PROBLEM
  I just can't calibrate my screen. Everything I do just does not work.
  Calibrating monitor in Windows 8 works very well only during the time when I actually do
  But if I restart, stop, or put my laptop to sleep just goes back to normal.

  For example, as a first step, the screen of Loggin on Windows 8 when I start seems calibrated.
  but when I connect I wait 2 seconds or two and all my settings are changed in return.
  I have to recalibrate the screen again and again once and again and again...

  Swear to God that I tried all possible solutions to solve my problem and none of them worked.
  I have read a lot of forums, and I can't find the solution that actually works.
  I did the solution 'Safe mode' , the 'clean boot' solution, in 'color management', I changed the settings (in a way that people who said it should work).
  I've updated all my drivers (my system than the GeForce GT 750 M is up to date). I installed all available updates for Windows 8 (when I check updates, the system tells me there aren't everything and my system is also up-to-date).

  I guess there could be a problem with my graphics card. I know that everyone has had problems these last time with the new update for GeForce, but like I said before, if I have confidence in my laptop then my graphics card is up-to-date.

  It really bothers me. It's annoying and I'm frustrated by that. The worst is that I can't find a solution to this, so I'm really asking for help.
  Thank you!

  Original title: calibration unsolved display problem - Windows 8

  Adeline B, thank you very much for your answer.
  I'm sorry that I have not responded in such a long delay.

  Well, my problem has been resolved. I downloaded my GeForce graphics driver was last updated.
  Now everything works fine.

  • I know that this problem can be irritating. If anyone has the same issue so I recommend you (like everyone else) download of the updated driver for your graphics card.
  • If this does not work, try to calibrate your system using programs/software installed on your computer by your manufacturer. In my case it was splendid ASUS utility. I also used Intel® HD Graphics Control Panel.
  • Another thing is you may think that your system does not calibrate when it actually... made. So what you can do, it's just waiting for the start until your system is finally charge up. In my case, Windows 8 something takes about 10 to 12 seconds, until what it changes all the settings of ' my settings'.»» Then first Windows 8 loads up to original settings (and this is why you find that your screen is not calibrated) but then it loads the calibration settings you make before you restart and all is well.

  I know this sounds so easy is probably not solve anything, but when I had this problem with the calibration I was so irritated by it I wasn't noticing the changes! I'd just instantly to the desktop or control panel configuration, or web and try to solve the problem, without waiting for my system completely load all settings. But... If the wait does not then consult my previous statements.

• DAQ channel property node

  Hello world

  According to the statement, NOR for the verification of the Pxi4330 procedure, I need "Disable calibration shunt for the channel by using the property node DAQmx Channel, you can find custom I/O" DAQmx - data palette purchase LabVIEW. "'" ' Select the analog input"General properties" conditioning of signals ' bridge ' Shunt Cal "activate property of Shunt Cal. "but I can't select this property that I want to say there is no property such as?

  What is everyone knows what the problem is? I lost 3 hours to solve this stupid problem, still can not find it.

  When I choose the General Properties property, analog, node there are two options that are not the answer.

  Please help me on this

  Thank you

  Hi Eric,.

  You have an SMU-4330 installed on your system? There are MANY properties of different devices, and to avoid confusion of the properties that do not apply to you, DAQmx tries to hide the properties that are not applicable to all devices in your system.  If you don't have an installed SMU-4330 (or a simulation of SMU-4330), then the property you are looking for appear by default.  To find it, you have two options:

  Option 1: turn off the property node filtered by right-clicking on the channel property node, by choosing "Select filter...". "and then selecting"display all the attributes:

   

  or Option 2: install a real SMU-4330 or simulated in your system. You can install a device simulated through the program of Measurement & Automation Explorer (MAX):

  

• amplification of the strain by using the cDAQ

  Hello

  I am a newbie in the use of DAQ hardware and hope someone can help out me.

  I recently bought a cDAQ with the NI 9237 to measure the strains. The strains that I try to measure are very small 1 series micro. A bit of research showed me that I need to amplify the signal to measure these small strains (correct me if I'm wrong). But I'm not able to find amplifiers for the cDAQ.So, the questions I have are-

  1. is it possible to measure these small strains (1 strain micro) using the cDAQ? If so, do I need an amplifier?

  2. If I need an amplifier, are there more specific for the cDAQ with the 9237? If this is not the case, how and where can I get one?

  Thank you

  SID

  SID,

  These results were very shocking for me also, so I looked into it further.  It seems that the 9237 can do better.   Assuming you're within 5 degrees of the calibration temperature (25 ° C), 9237. 05% of span of error and. 05% offset error.  With the range of configuration and 25mV/V full-bridge, you can calculate the absolute accuracy of the 9237 with the following formula.  (Sound of full-bridge = 0.9 microV/V)

  absolute accuracy = (gain error * reading) + (error offset * range) + (noise)

  Do the math, we get

  25mV/V + / 25.9 microV/V

  In a full-bridge configuration: V/Vex =-(Gauge Factor) * strain

  
  

  With a typical GF of ~ 2.0, we can say that the accuracy of the strain will be

  12.5 mm/m + / microm 12.95/m

  It's a little more in the range that you hoped for.  Sorry for the confusion.

  If this does not work for you, we sell solutions PXI who will be able to measure more precisely.  Similar math help and type of configuration of full-bridge with SMU 4330 plug, we get:

  12.5 mm/m + / 3.48 microm/m

  In my view, that it is card data acquisition based on a bridge more precise and accurate that we sell.  It requires a controller/chasis PXI.

  Please let me know if you have any other questions!

  Sincerely,

• EMagic Logic Control has stopped working

  I have havn´t been using my Emagic Logic Control for a while and as I wantted to use it it didn't work any more.

  EMagic Logic Control doesn´t appear in the configuration of logic controller, but the Jog Wheel works?

  Mac Pro early 2012

  Unitor 8

  RME Fireface 800

  EMagic Logic Control - v 2.1.2

  Logic Control XT eMagic

  OSX 10.11.6 (El Capitan)

  9.1.8 logic (64-bit)

  I tried on:

  trashing the prefs and controller logic Surface prefs, then restart

  2 different midi interfaces

  different midi cables

  different supplies

  tried to re - install the 1.02 update firmware with no success

  also, another computer running OSX 10.11.6 and logic 9.1.8 (64-bit)

  Switch between mode Mackie and logic

  When I turn on Emagic Logic Control, it passes through the calibration Fader without problem, but doesn´t go further and sees no logic, but Logic Control XT Emagic is considered by the logic.

  It seems that the midi input does not work.

  You have any ideas? Maybe it s a hardware failure and I should try to find spare parts?

  Well cordially

  Henning

  EMagic as a society has not existed for so long now and their products have not been updated for so long, I think that it is no longer compatible.  He did stop working with an upgrade of software of any kind?  Yes, it's going to be difficult with this type of old hardware.  I would have the Unit checked out by someone who knows how to check what works and doesn't work inside.

• Battery meter

  My iPhone 6 is running iOS 9.3.1 just today started having a problem with the battery meter records does not correctly. After several hours of using my phone this morning, I noticed that he was always at 100% and he died soon after. It wasn't a problem last night, because I remember watching down to 4% and die last night. I had my time manually rather than what allows it to configure automatically. This http://fortune.com/2016/01/19/battery-issues-iphone-6s-and-6s-plus/ of fortune dot com suggested to do a hard reboot and automatic time setting enable. I restarted, and then activated, then restarted again, but nothing.

  I got the iOS version that I am running for awhile, so I don't think that it has nothing to do with the update because I only started to have a problem with it this morning

  First, download the autonomy since the app store app. It will tell you the status of the battery. Then try the battery meter calibration if the problem is not the battery.

  Recalibrate your battery meter:

  • Charges to 100%
  • Run the battery until the phone turns off
  • If it stops above 1% charge for only one minute, and then continue running the battery down. Repeat until it makes 1% before shutting
  • Load it back to 100%

  If the battery is defective, this should fix it.

• S920 proximity sensor

  Hi, my S920 has a problem in the proximity sensor (the screen does not turn off during a phone call), I think it's a problem of software/calibration but the problem is when I go into the menu factory is all in Chinese and unfortunately I can't read Chinese... If this option is available, can some body please guide me through the menu to reach the proximity sensor calibration option (for example, 2nd option-> 3rd... etc)

  The problem is I bought the phone from Sharaf DG in Abu Dhabi during a visit and when I went to them, they said, that he needs 10 to 15 days... I live in Jordan and my visits are usually 2-3 days every few months!

  Hi ice_T,.

  I have some advice for you.

  First of all, could you please check your call settings.

  

  Go to the Dialer, then Menu and call settings. Check if you have selected to proximity sensor.

  Then you can try to install this application on Store.

  https://play.Google.com/store/apps/details?ID=com.kristofjannes.sensorsense

  This app you can test this senson if does not work on.

  Please let me know if this helps or not.

  Thank you

  J.

• A720 cannot restore to factory setting

  I can't restore my A720 back to factory setting. The error indicates the partition has changed.

  What I did that he messed up:

  1. I have partitioned the C drive into 2 partitions so that I can install Windows 8 on one of them.

  2. everything went well. So I decided to remove WIndows 8.

  3. I deleted the partition Windows 8 and he added to the C partition.

  4. I had trouble getting my calibrated colors (this problem was present from the first time that I turned on the system. No the above procedure).

  5. I chose the OneKey restore announcement that it restarts.

  6. when I hit the F2 key, it has a display to dual boot, but only of Windows 7 has been in the list.

  7. I had already made a series of Recovery DVD, so I inserted the DVD #1 and restarted.

  8. I press a key when prompted and restore screen came.

  9. I hit him food and and it appeared to work until the error dialog window appears saying that the size of the partition was incorrect.

  Help! Thanks in advance.

  Bloo,

  I finally got the correct disks. I was sent a total of 5 sets of CD. All were for the A700 except the last game.

  I had pretty well given the fact that I was going to send the unit to the factory to restore. They actually sent me a box to ship it in. Fortunately, before I packed it upward, I got quite unexpected package. Voila! It was the right set of discs and now my system runs like a champ.

  Thanks for your help on this Bloo.

  Frank Olivio

• Variation of thermocouples (+ - 2 ° C) and are under the same conditions

  Hi, my English is not the best but I trust in your intuition and intelligence capacity.

  Actually Im connecting many thermocouples (type J) in a DAQ 9213. I managed to take all measures (7 thermocouples) and also the thermocouples are calibrated. My problem is that the 3 thermocuples give me one 20 ° c (60F) and the other 4 give me 22 ° c = 71.6 ° F, and all the thermocouples are under the same environmental conditions.  The easy solution is to put an offset and compensate for the error but it is not a good solution.

  Can someone tell me what is happening? I think it's wiring problem maybe the COM, but I've referenced the negative signal (low signal) to the COM, also tried not to referencing the negative signals to the commune, but the result is worse because the signals are going crazy.

  Please help me, please!

  Hi Jesus Hernandez

  Also remember that the thermocouples have a positive and a negative side, so if you plug wrong temperature will be different and it will decrease rather than increase when something warmer so close.

  Best regards

  Julio Mena

• printing color out of alignment with the double image

  HP Color Laser Jet CP1515n.

  Windows 7 Home Premium 32 bit.

  When printing in color, the colors of the text and graphics documents is out of calibration between them, which appear them blurry double image. I recently renewed the black cartridge and subsequently checked all other cartridges to ensure they were well calibrated, but the problem remains.   Please advise?

  Hi daggan,.

  You can install the printer on another computer running Windows 7 to see if you have the same problem?

• Black print cartridge registers is not on the right side of the page

  CP1215 has developed a weird problem! Recently replaced the black print cartridge (new, original HP).

  Printing a document in BLACK color, this isn't a problem. Crisp and clear impressions.

  Print the same document in color gives completely misaligned recording BLACK on the side RIGHT of the page. The side LEFT is clear!

  Printing CONFIGURATION PAGE confirms the problem. Registration of marks below on the LEFT are perfectly aligned.

  But on the lower RIGHT, all colors are aligned with the exception of black - the black line is much higher and offset printing to the right where it should be. That's why the color prints are all blurry on the right side of the page.

  Calibration several times running, check the drivers etc.

  Any help/advice is really appreciated!

  Hi Gemini02,

  Sorry about the long absence, but was busy with other stuff. More beat troubleshooting according to your last email.

  First of all, a few answers to your questions:

  1. don't know what the problem is. Don't want to start replacing immediately.

  2. all ink levels are more than 80%; Black nine.

  3. all the cartridges are original HP Black has been replaced recently, the other three provided with your printer.

  4. the paper is double-a premium, 80gr

  5 paper is set on the plain. Have you tried with the HP90 and light parameters too.

  After following your instructions of troubleshooting:

  6 printer moved closer to the wall outlet - it's a machine heavy tho!

  7 pressed & held green button. Config and supply status printed pages.

  8. print with other applications (Photoshop, Word, PowerPoint and Adobe Reader).

  Problem persisted. Registration completely to the bottom of the hand right side of the page and the worst in the lower corner straight out.

  Acts of desperation next, pure:

  9 deleted each cartridge, shaken several times on the axis horizontal and then triggered one end while decreasing the other and vice-versa several times. Replaced in the status bar.

  10. Ran HP Toolbox calibration.

  11. test print to Adobe Reader - same document as before. Substantial improvement!

  12. Repeat steps 9 and 10. Further improvement.

  13. Repeat steps 9 and 10 more. Almost no problem checking.

  14. Repeat steps 9 and 10 more. No record of the questions at all!

  Then, to avoid the location and power source:

  15. moved printer in its normal location.

  16 connected the printer to its normal power source - an extension of good quality.

  17. reprinted on the same page. No registration no questions at all.

  I have no idea why the steps 9 and 10 would have such an impact. And why repeating them would improve the print quality progressively until no problems are observable. I have detailed my action here in case they can help someone else.

  I thank very you much for the support and guidance you provided. If you have any idea why the repeated shaking and calibration solved this problem, I would be very interested! Keeping in mind I ran several times previously without success to calibration.

  Thanks again for your help.

• How do I remove a single white line on the right side of the printed page

  Appears on all printed pages, regardless of the source.  Kaleidoscope, cleaning, installation of new print heads and the linefeed calibration solves the problem.  The printer is an Officejet Pro 8500 a Premium.  Thank you.  I'd hate to throw a 18 month old printer in the trash.

  When you say that the issue is on the right side you mean the right side (and along the way on paper) when printing in portriat mode?  If so the problem may be due to a spot on the MICR band.  It is a fragile and delicate, tape printed with hundreds of lines per inch that the printer uses to know where the print head on the entire page.  Cleaning the MICR band, as described in this post can help solve the problem.  Be sure to heed the warnings.

• Brightening video for YouTube

  Hi all

  I created my video on a Mac and upload it to Youtube.

  http://www.YouTube.com/watch?v=8LDEOuHhYrs

  A few comments from people who have seen it, is that some scenes are too dark.  I had done a dark scene intentionally, but when I read the video on YouTube from my neighbors HP computer was dominant than what I created color darker and slightly different.  I don't know if it's a Mac/PC thing or a thing of Youtube - Mac/PC, or maybe just his computer screen, but she said that it was too dark on his cell phone (non-Apple).

  On my computer I have compared the clichés of the video inside Premiere Pro for the same shot on Youtube and the color is relatively consistent.  I read that APPLE has its own way of interpreting the color so I'm Hovanessian is a Mac/PC thing, and since most of the world is not Mac I should take account of the majority.

  So I need some advice on whether I should download a brighter version of the video, and what would be the best way to do it.

  Thanks Cris

  Well, for me it looks OK on my monitor (sRGB calibrated). The problem you are having is that unless everyone has calibrated his monitor, it will always differences in the Gamma and color apparent. Adjustments of brightness, color temperature, color etc adjustments can significantly influence the perception and, which also affect the environment of the ambient light, glare on the screen, the background color of the wall and so forth. There is litetrally of hundreds of books delaing with it. Above it, up to that recently used operating systems different Gamma - Windows has always used 2.2, Macs historically 1.6 and 1.8. Only OSX 10.6 it also unifies using 2.2. So no matter how you twist and turn it, there will be no satisfactory solution to your problem. You could clear up slightly to address a wide audience, but that should be very subtle. As I said, the colors are fine for me as they are. Adjustments excessive would be ruin.

  Mylenium