Call "HostNetworkSystem.UpdateVirtualSwitch" for the error of the object when you attempt to add the second NETWORK card

Similar Questions

• CMS OVA, adding the second NETWORK card breaks the first NETWORK card

  I'm testing CMS 2.0 and when I try to add a second NETWORK card in VMware, he immediately interrupts the first network card.  As soon as the loading of the image, the first NIC fails.  Even if I disable iface b, it will allow all traffic where iface one.  If I stop the application, remove the NETWORK adapter and run it back again, it works very well to the iface one.

  I want to test the public face with box feature, but I can't if I can't add a second network card.

  How do you add the second network interface and interface you add?

  You should add 'VMXNET3' type if you use VMWare, if you chose something else, you invalidate your license, see section 3.3 of the virtualized CMS 2.0 Setup Guide for deployments.

  If you need assistance, you must move this thread to the section of telepresence of forums, where this device is actively discussed.  You can change your question and change the categories at the bottom of the page.

• Add the second NETWORK card to vSwitch

  I'm working on trying to add to install a second NIC physical to the vswitch which is installed by default when ESXi. I use the code below, but when I run it, it disconnects in fact the main physical network card and of course, I then lose connection. I tried different varients of this and even finished by adding a port of vmk, which I didn't do. I just want to add the second network card as a standby card network.

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1
  

  The cmdlet Set-VirtualSwitch accepts a string array as the value of the parameter - Nic. So you should be able to:

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1,vmnic2
  

  Best regards, Robert

• How to associate a VM for the second network adapter on the host

  Hello

  I have created a virtual machine and added a NIC that matches the first physical network adapter on the host Machine. I then added a second NETWORK adapter on the host. I would like to create the second network adapter on the same VM and map it on the second NETWORK adapter on the host. How can this be achieved.

  When I use the "Add Hardware", I does not enumerate the physical network adapters on the host to choose and assigns a VM mac address.

  Kind regards.

  VMware customers use virtual network adapters if you need for a great, a second deck on the host card, but how to do this depends on the host OS.

  For Linux, just run vmware - config.pl and choose to create a second bridged network adapter, choose the right pair of physics.

  For Windows, run vmnetcfg.exe (as an administrator), disable the automatic bypass and then manually fill the two physical network adapters (for example to create two VMnet adapters * with each mapping to a different physical NIC). You also need to restart the host VMware Agent services and VMware Server Web Access before these virtual cards will be available for use.

  Chapter 11 of the guide is a good reference for all this - http://www.vmware.com/pdf/vmserver2.pdf

  Guy Leech

  VMware vExpert 2009

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Operation Failed, error 0 x 00000002 when you try to add printer on Vista Home Premium

  WiFi printer (Kodak ESP 7 all-in-one) works very well for centuries. Had to do a system restore with my HP under Vista Home Premium laptop. Then the printer could not be detected. Removed from the printer. Downloaded latest driver from Kodak. When you try to add the new driver/printer, it gives me an error 0 x 00000002. Also just tried to add the printer in the printer browser window and does not see on the wi - fi network, even though I know that it is connected.  Kodak assures me that it's an OS problem. I know that the print spooler and dependencies are running. Have tried various solutions several times between reboots.

  Hello

  You can also track information to try to solve your problems of printer below

  read the printer correct that information the slot microsoft, including the 'fix - it' and the other links here

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  and read this microsoft tutorial too

  Introduction

  This tutorial is designed to help you identify and fix the problem printer common windows problems, including print errors, or errors, and other issues that could prevent you from printing. This tutorial does not cover printing problems related to specific programs. Printing problems can be caused by cables that are not properly connected, corrupt, drivers, incompatible drivers, the printer settings, missing updates and problems with your printer.

  How to use this tutorial

  For best results, complete each step before move you on to the next. Try to print after each step before moving on to the next step.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• IMAQdx mind traffic on the second NETWORK card

  Hello!

  My system:

  -Labview 2011 SP1 with NO Vision and IMAQdx

  -Windows 7-32 bit

  -2 NICs (Intel Pro 1000)

  On a NIC (subnet: 192.168.0.x - Intel pro driver) a sick Ranger is connected. Store it works with Studio of sick Ranger or the Labview Toolkit Ranger.

  On the second NIC (subnet: 192.168.1.x - Realtek dreiver) a Vision of Basler GigE camera is connected. It works with the grun80 pylon Viewer and IMAQdx GigE functions in Labview.

  If I start the acquisition of two cameras using the Studio store and Basler pylon Viewer (no Labview) both cameras acquire images at high speed without any interference.

  If I use Studio Ranger or LV-store Toolkit for the Acquisition of store it works selection UNTIL I have start a Labview VI containing the screw IMAQdx to acquire images of the Basler camera. As soon as the VI performs stops Acquisition of Ranger and Ranger loses the connection.

  I guess the driver IMAQdx is somehow interfering with two network cards.

  Suggestions how to exclude one of the NICs of IMAQdx driver or can someone tell me what is happening on the network driver layer when loading of IMAQdx?

  The purpose of my request to LV, is that both cameras can be used at the same time!

  Thank you!

  Disable the identification of cams network solve the problem?  See also How to disable IMAQdx sending periodically a Ping 'discovery'.

• Impossible to use the second NETWORK card on VM

  I'm under VMware Workstation9 and I'll put up a configuration 5.1 ESXi

  VM1 - Windows 2008 - acting as a DC and a NFS storage
  VM2 - ESXi 5.1

  I added a second NIC on VM1 and VM2 to IP storage but I can't PING vice versa

  IP address:
  VM1 - 198.168.150.10 SM: 255.255.255.0
  VM2 - 192.168.150.11 SM: 255.255.255.0

  VMnet2 is used for the management, no problem with this vmnet3 is used for storage traffic but no communication possible

  Any Suggestion?

  Check the response of jmattson to Re: operating system of the virtual machine attempted to activate the adapter Ethernet0 promiscuous mode. This is not allowed for security reasons. solves the problem.

  André

• How to add the second network card?

  A server (VMware ESX 4.1) works well with a network card. Since I want to add a virtual switch, I need to add another network card. So I inserted into a PCI slot and reboot ESX. But the ESX does not. I need to reinstall ESX to let him find this network adapter?

  Thank you very much for the help.

  The added network adapter is Gigabit PCI Desktop Adapter, D-Link DGE-528 t.

  I tried several model D-link years... None of this can work.

  Use a broadcom or Intel card (and listed in HCL).

  André

• How to use the second network card physical to Virtual Machine?

  Two queries. We strive to VMware Server 2

  How to increase the speed of the network of the guest operating system.  Currently it shows 10 Mbps.

  If we have a second physical network adapter, is it possible to use it for the guest OS. ?

  We are noobs, please give links to this info or explain in steps.

  concerning

  Merlina.

  Welcome to the VMware forums communities.  You may be able to fix your problem by changing the type of virtual NETWORK adapter and install VMware Tools.  See this KB article - http://kb.vmware.com/kb/1002456.

  Dave

  VMware communities user moderator

  Now available - vSphere Quick Start Guide

  You have a system or a PCI with VMDirectPath?  Submit your specifications to Officieux VMDirectPath HCL.

• Recommendations for the 2nd guest card, ESXi 4.1?

  I use ESXi4 in a House on a low-cost Dell image headless server. I would like to add a second network card PCI host - maybe an Intel PRO/100 and PRO/1000 off eBay - which is supported on ESXi 4.0 and 4.1.  My PCI adapter only supports 32-bit cards.

  Performance is not a serious problem, but I would like to find an adapter for under $ 25. I'll use this to experiment with different firewall, routing, and VPN between the WAN configurations (for example: DSL) and LAN.  It's more convenient and more 'green' to keep all my virtual machines guests on a single box, but references the list of cards supported against froogle and Bay takes more time than I expected.

  recommendations, pointers, and personal experience would be appreciated...

  I think the most common whitebox NIC's Pro 1000 GT.  ESX(I) dropped 100 MBps NIC support so I would avoid this option even if there is a community update driver Pro/100.

  Dave

  VMware communities user moderator

  Now available - vSphere Quick Start Guide

  You have a system or a PCI with VMDirectPath?  Submit your specifications to Officieux VMDirectPath HCL.

• Configure the 2 network cards in a VM for MPLS LAN and the other for internet

  Dear all,

  I have a HP Server with 2 NIC cards. ESXI 4.0 is installed and 3 VM was created in it. Initially that a NIC card was connected to the path of the LAN MPLS switch and another card NETWORK was not connected to the internet switch port.

  Each VM only had a single NIC in it. So I assigned MPLS IP LAN to ESXI host and VM 3 and everything worked perfectly.

  Now, I wanted to have the internet connection for my 3 VM. So I plugged the 2nd NETWORK card with internet port and added the second NETWORK card to the ESXi using the Vsphere client - & gt; configuration - & gt; Networking option. Now the two nic cards are ponting to the network of the virtual computer.

  I've added 2 network card to all 3 VM and assigned to the internet IP addresses to all of these NICs. order of MPLS and internet work at the same time, I removed the card NIC MPLS entry door and manually routed through route add command. After this MPLS and internet worked well in 1 VM.

  I tried the same thing in 2nd and 3rd VM but it failed. whenever I have add 2nd network card in the virtual machine, the first of this virtual machine network adapter does not work.

  I'm after the right approach? Help, please...

  Kind regards

  Ashok doriane

  If I understand correctly your installation, you connected the physical NIC to two different IP networks.  Then you connected these cards in the same switch-v on the server.

  This essentially fills two different networks at the layer level 2 layer 3.

  You want rather than the two networks remain separated inside the host.

  • create a new v-switch on the host

  • move the internet NIC v-switch

  • Move the second NIC on each virtual machine to this switch

  • Make sure that access to internet VM NIC is one with a default gateway on a virtual machine OS

  • remove the default gateway of the NIC MPLS

  • creating persistent static routes to the NIC MPLS for any affected networks it beyond the same subnet as the NIC itself.  Addresses on the same subnet will be automatically accessible. Just roads for those outside this range.

  Steve Puluka

  JNCIA-ER enterprise routing

  Enterprise JNCIA-EX switching

  Senior network administrator

  Liberty Dialysis

  http://puluka.com/home

• Adding a second NETWORK card on the server HP Proliant ML 350 G5

  I have a new HP Proliant with a guest of Windows 2008.  HP came with two network cards on the MB.  I need double-home this box on both networks, at least for a while, and this server will be the only road between subnets.  It's just a stand-alone installation inset.

  I looked in the settings of the BIOS on the HP and it's a little confusing, but I'm sure that the second network card is active (it lights up when it is plugged).  When I try to add a NETWORK adapter to the configuration of the host, it is as if the second NETWORK card is not present.

  My question is what is the best way to add this second NETWORK adapter and how do I do that?

  I'll need access to the host of the VI Client on both networks - at least for a while.

  Any help would be greatly appreciated.

  If you go to configuration-card network in the vSphere client is the 2nd NETWORK card that there are listed?  If ESXi is able to recognize the NETWORK adapter (or other people that you add) they should appear in this list without any config changes and be ready for use.

  What kind of networks are you fill?   If one is considered not secure you could be better not add a management on this network port and prefer to have access via a VPN VM or a secure hosted VM / dual.

  Dave

  VMware communities user moderator

  Now available - vSphere Quick Start Guide

  You have a system or a PCI with VMDirectPath?  Submit your specifications to Officieux VMDirectPath HCL.

• Error blue screen STOP: 0x0000007e. I powercycled the sys, unable to choose for sure (keys do not work when you try to select a mode) sys is trying just to go back to the blue screen. Help, please

  STOP: 0x0000007e (0xc000001d, ox8537008 0xba4c3508 0xba4c3204) and the system would not come to the top.

  Error blue screen STOP: 0x0000007e. I powercycled the sys, unable to choose for sure (keys do not work when you try to select a mode) sys is trying just to go back to the blue screen. Help, please

  Symptoms: Booted computer, loaded the raid drivers and showed at the start screen XP for half a second then to BSOD with a Stop error Code 0x0000007E - see also a lot of users (0xC0000001D, 0 x-, etc.) as well.

  Solution:

  1 boot from your Windows XP CD and start the recovery console. You may need to press F6 while RC loads in order to load the SATA drivers. you will have a prompt c:\WINDOWS to the console.

  2. type: CD $NtUninstallKB977165$ \spuninst (it's the update, I had to uninstall to get out of the boot loop, other updates can be uninstalled by changing the name of the directory to $NtUninstallKBCODE$, where KBCODE is the code KB)

  3. type: BATCH spuninst.txt

  4. type: exit

  Don't forget to configure your system to boot from the HD before resuming. I hope this helps. Saved me a lot of hassle today.

  -Tom Steele
  http://www.hawkandtom.com Tom Steele

• details of error: code 80071a 91 when you try to install the 'a security update for windows vista (kb2855844).

  details of error: code 80071a 91 when you try to install the 'a security update for windows vista (kb2855844).

  does anyone know how to go beyond this error?

  Thank you.

  Moved from Vista to install, upgrade and activate Forum.

  Take a look at this thread:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update/unable-to-install-updates-getting-error-code/27a21977-F964-4376-BFAB-2f29ea127c6a

• Automation error: The object invoked has disconnected from its clients when the exe to exectuted the VB6 for the second time

  Dear all,

  I had this really common automation error when I run an exe file created by Visual Basic 6 for the second time. Whenever I ran the program for the first time that it works really well. But the second time always fails. When I ran in debug mode in Visual Basic 6, sometimes it worked. I checked the code and found it would be discontinued in the next part - CommonDialog1.ShowSave.

  ReDim SelectedVar (1 NumSeleVar)
  ReDim SelectedVarTxt (1 NumSeleVar)
  I have = 1
  For j = 1 To NumVar_GasPlants
  If chkOpt (j - 1). Value then
  SelectedVar (i) = j
  SelectedVarTxt (i) is chkOpt (j - 1). Legend
  i = i + 1
  End If
  Next J

  'Get the name of the export file.
  If not g_RunOutputMacro then ' check-out
  CommonDialog1.cancelError = True
  CommonDialog1.InitDir = curCasePath
  If IsMonteCarlo then
  CommonDialog1.FileName = "HourlyData_GasPlants_" & cmbYear.Text & "_" & cmbMonteCarlo.Text & ".csv".
  On the other
  CommonDialog1.FileName = "HourlyData_GasPlants_" & cmbYear.Text & ".csv".
  End If
  CommonDialog1.Filter = ' (*.csv) | * .csv.
  CommonDialog1.FilterIndex = 1
          CommonDialog1.ShowSave
  SelectedOutputFile = CommonDialog1.FileName
  On the other
  SelectedOutputFile = g_Output_FileName
  End If

  I have been tormented by this problem for almost a month. Any suggestions or ideas would be very appreciated!

  Thanks a lot guys!

  Hello

  This problem would be treated better in the MSDN Visual Basic forums. Expertise it can help you with this problem.

  https://social.msdn.Microsoft.com/forums/vstudio/en-us/home?Forum=vbgeneral

  Thank you

  Stephanie Podder