Call Manager Express has no type 6961

Similar Questions

• Phone to the Call Manager express license

  Dear,

  Is the license of phone required for Call manager express or the license on the bridge of voice enough to operate the phones?

  Kind regards

  A device license is required for phones on CME. Reference numbers

  FL-CME-SRST-5 =.

  FL-CME-SRST-25 =.

  FL-CME-SRST-100 =.

  Aerts.

• HWIC-AP more Call Manager Express?

  It took me some time and many transfers of tftp to finally find an IOS which works very well with the HWIC-AP (wireless access point module) for a router in 2801.

  What I was asking: is there an IOS which supports both HWIC-AP and also includes the Call Manager Express (CME)?

  What feautures would you find using the IOS search engine?)

  Thanks for all the ideas.

  Marc

  Use the IOS 12.4 (2) T1 or later to support the CME and HWIC-AP

• Call Manager Express ATA187 Firmware update

  Hello

  I recorded with Call Manager Express 9.0 to ATA187 but I have a problem for outgoing calls using DTMF, I tried to put dtmf-relay into the pool of register of voice but without success, so I decided to update the firmware.

  the problem when you go to download page you will find a .zip to the file not as before managing the .zup file and the upgrade of the firmware for the express appeal not found in any document because there is no way to upgrade through phones analgo

  No idea how upgade using any way?

  Hi mrmhar1408,

  You must upgrade the ATA 187 for the latest firmware SIP (9.2.3) using this load file, ATA187.9 - 2-3 - 1.loads. It is in the zip file available on the download section of cisco.com to the ATA-187, the name of the zip file is cmterm - ata187.9 - 2-3 - 1.zip.

  The process of upgrading of the ATA and SIP phones 187 s in SIP via CME are listed here. The process is essentially the same for phones and ATAs.

  http://www.Cisco.com/en/us/docs/voice_ip_comm/cucme/Admin/Configuration/Guide/cmeinstl.html#wp1067416

  Note that you must also have the load the copied file first in memory flash TFTP server, that would be your router CME flash.

  HTH.

  Kind regards

  Stefano.

• Cisco Call Manager

  Hi, I want to know whether or not our current phone system uses the CCM? Unfortunately, I know that even with our systems and next thing I know, it's that use us Cisco Configuration Professional utility to configure the phone display names and update the date & time.

  Could someone provide me with the steps to check if we use CCM/CUCM? Sorry to be a beginner.

  Call Manager Express, another acronym which is CUCME - Cisco Unified Communications Manager Express.

  CME/CUCME is function of the router, you can access it via telnet/ssh.

  CUCM can be access through GUI and SSH.

  Kind regards

  Mohammed Noor

• ASA/IPS and IPS Manager Express

  I am trying to add my sensor to the IPS Manager Express but I keep the following error. IOException when trying to get certificate:java.security.cert.CertificationExpiredException: notafter Sam may 10 * 2008.

  I'm sure it's simple but can find how to solve this problem.

  Kind regards

  D

  This means that the SSL/TLS certificate on the web server of your sensor has expired on May 10, 2008.

  It is very common for the sensors that have been active for more than a year. When a sensor is generated, it is usually valid for only a year or two.

  You just need to create a new SSL/TLS certificate for your sensor.

  Connect on your sensor and run "tls key generate."

  http://www.Cisco.com/en/us/partner/docs/security/IPS/6.1/command/reference/crCmds.html#wp504369

  But remember that, once you do this, you should make sure attend you all other management systems that connect to your sensor and make sure the management system pulls down and accepts this new certificate (which often requires you to push some type of button I agree to the new certificate).

• Call Manager 6.1 network problems

  I have a problem with my network drops continually calls phones or freezing.  Its States CM low features disabled.  We lose calls, phones are freezing intermittently.

  Here is the hardware configuration: MCS-7828-H3

  Platform Type 7828 3 H

  Series MX282400CM

  OS active 6.1.5.10000 - 10

  RTMT shows opt-out phones, but I don't see all devices lose connectivity with the exception of some packet losses minimal for call manager.  No other error not reported in to any device Cisco syslog for example, ping sent to all major network devices have 0 packets lost over the weekend, but 250 on 20 000 ping on the call Manager server is lost.  I replaced the cables, cords and moved from the ports of the switch with no resolution.

  CPU has never been higher than 24%

  Virtual memory never higher than 30%

  Active and Inactive partitions are 15% of disk space.

  We have a 2nd NETWORK adapter on the server, but I can't configure this 2nd NIC as a stand-alone connection for the call Manager server, than as a failover for 1 NIC.  Does anyone know how to configure this 2nd NIC to host all these servers IP services?  Is there a way to replace the NETWORK card on those servers (not on site and have yet to open this box upwards) or do I have to replace the entire server?

  Does anyone have any other suggestions on where to take my troubleshooting?

  Thanks for all the tips!

  Steve

  Please see below, your right in thinking this could be a faulty network card, cable, I suggest you also to search in your STP configuration.
  

  Error Message RTD-1-ADDR_FLAP [tanks] [dec] base10 relearning / min

  Explanation normally, MAC addresses are learned once on a port. Sometimes, when a switched network RECONFIGURES, due either manual or STP reconfiguration, addresses learned on a port are relearned on a different port.  However, if there is a port anywhere in the switched domain that is loop over itself, addresses will jump backwards between the real port and the port that is in the path to the rear port loop. In this message, [tanks] is the interface, and [dec] is the number of addresses being learned.

  Recommended action determine the actual path (port) to the MAC address. Use the ethernet controller of debugging command EXEC addr the privilege of seeing the other path-port on which the address is redisplays. Go to the switch that is connected to this port. Note that the show cdp neighbors command is useful to determine the following switch. Repeat this procedure until the port is found who receives what it transmits and remove this network port.

  Link to Error Message-RTD-1-LINK_FLAP [tanks] down/up [dec] times / min

  Explanation this message means that too many events from the bottom up link was noticed on this interface: [tanks] is the interface, and [dec] is the number of times that the link goes up and down. This could be the result of reconfiguring the port, or it might mean a faulty device at the other end of the connection.

  Recommended action if a person is to reconfigure the interface or device across the interface, ignore this message. However, if no one manipulates the interface or device at the other end of the interface, it is likely that the Ethernet transceiver at one end of the link is faulty and must be replaced.

• mail electronic outlook express pop - up-"outlook express has encountered a problem and the need to close.

  I am running XP.

  When I select an email or try to create an e-mail, I get the Outlook Express "pop up" where it is said

  "outlook express has encountered a problem and need to close... Sorry ".  Asks me if I want to send a message

  for Microsoft, when I click on the option, the screen freezes and I have to type the keys del Alt, control, in order to free

  and end of the task.

  You may have a damaged identity especially if it's the default main identity. File | Identities | Add the new identity. Create a new one and try it. If all goes well, you can import your messages and address book from the old identity and delete it.

  Note: Do not use the main word in the name of the new identity.

• Review installed licenses V4.3 cisco call manager

  Hello!

  I have and old cisco call manager V4.3 and I need to review with the licences it has installed, did someone knows how can I get this information from this version? I checked under license of the system, but nothing is there.

  Thanks in advance!

  Kind regards

  There are no licenses installed on versions of windows, you can not get any info from the server. You should review the licenses of the size of the paper.

  Sent by Cisco Support technique iPad App

• Strange problem with call manager and call before all

  Not sure whether this post about unity for or CCM. I will post on both. I have a main number customers dial in. When they call this number and they do not get a response, it passes to a call handler. This call handler has an option of entry of the appellant 3. If they hit option is three transfers to an IP phone on Call Manager who is assigned to the CFA for this cell phone to people. Everything works except when the call is sent to the PSTN it sounds for time and then disconnects. This number can be called directly from the system with no problem. The cause of the disconnection on debugging is the following: because I = 0x80FF - error of interconnection of networks; not specified. Please help if you can.

  I assume you are using version transfers here. You can give it a whirl with supervised transfers?

• Issue of call manager

  We have a Manager call we use for AA to provide wishes and staff of mailbox access mailbox option and no DDI extension before you send us the receptionist (Call Manager driver Point to the monitoring console). Greeting for office hours and the other for off hours which takes messages.

  We had a request to remove greeting during the hours of office, so the rings call the pilot immediately Point, but always need wishes and message opting for hours.

  I have change the standard greeting of the current record to empty and the option after the salutation is to attempt to transfer to Pilot Point. This kind of work, but I get the system prompt to 'wait while I transfer your call', then a second or two from the Department of health before the Pilot Point rings.

  Any way I can stop the system prompt and the Ministry of health before the transfer so that the caller hears only ringtone? Here's how incoming call:

  RTC Via GW-> CTI Route Point-> Unit-> CM Point of pilot-> Attendant Console user

  TIA

  D

  Check out this thread for more information on how to replace the system with a white prompt we so used to hear you it any longer:

  http://forums.Cisco.com/eForum/servlet/NetProf?page=NetProf&type=bookmarks&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40.ee8253b/1#selected_message

  do not forget that it is not taken in charge of TAC, and the change will be deleted when you upgrade so you don't have to remember to reapply after.

  Not that you can do on the Department of HEALTH it - it is paid by the switch, not the unit.

• IPS Manager Express (IME)

  Hello everyone,

  I recently found a new product data sheet - called Cisco IPS Manager Express, looks a bit like a new implementation of the IPS event viewer.

  Currently downloading the software displays an error, but everything else is present.

  Short url is cisco.com/go/ime

  What is someone is aware of this tool? How to download?

  Concerning

  Mathias

  EMI is the next generation of VEI.

  It will keep track of IPS events and will also probe version 6.1 IPS configuration.

  IME is intended for deployment of sensors of 5 or less.

  EMI was announced earlier this week.

  It is in final testing and will be available in the next month or 2.

  IME will be available for download on cisco.com without extra charge for customers with active Service Cisco IPS contracts on their sensors.

  Besides IPS version 6.1 also announced, as well as the AIP-SSM-40 for the ASA firewall.

  IPS version 6.1 is mainly changes to work with the new Editor IME.

  The AIP-SSM-40 is the more powerful version of the AIP-SSM-10 and the AIP-SSM-20 and is meant for use inside the ASA 5520, and ASA 5540.

• Cisco IPS Manager Express

  I'm under IPS Manager Express 7.0.3, followed by several devices of ASA - SSM.  Recently the devices begin to show errors Event Status and sensor health seen in IPS Maine.  When I do a status of the device of the EMI, is getting the following error:

  Unable to get the version of the sensor. Exception: java.security.cert.CertificateExpiredException: NotAfter: Thu Aug 25 14:40:47 GMT + 12:00 2011

  If I delete the device from the EMI and then add it back in, I get the same error when the software tries to connect and so can add the device in IME.  I can't find mention of this in the IME or Online help document in IME software help.  I don't know which certificate software is the reference to.

  Has anyone seen this problem before?

  Thank you

  EDIT: Error nice to server ssl certificates expired on the IPS modules.  Generated new certificates and updated IPSME and CSM to recognize these and now they are all good.

  Hi Mike. Looks like you solved this before an answer was published. FYI (and good documentation incase everyone knows the same question and concludes this discussion), it is well documented here.

• Install experience with CSA 4.01 & Call Manager

  Someone at - he had luck get the Callmanager XML policy file and use with CSA agent install?

  I was not able to find the custom policy referenced in the doc, they was curious to know if anyone has installed the CSA on a Callmanager sever and what results have been.

  Thank you

  Here is the link to get the custom policy. I installed CSA on Call Manager several months ago. no problem so far.

  http://www.Cisco.com/cgi-bin/tablebuild.pl/CMVA-3DES

  Please do not forget to rate answers

  Thank you

  Travis

• Can I migrate a virtual computer to a new family of CPU? -Cisco Call Manager PUB/SUB

  I currently have 2 host VMware ESXi 4.1:

  1. Dell PER905 - running 16 x 2.39 GHz (core) CPU / Quad-Core AMD Opteron (tm) Processor 8378 (processor type)

  2 cisco UCS C260 M2 (BASE-2646) - running 20 x 2,393 GHz (core) CPU / Intel (R) Xeon (R) CPU E72870 (processor type)

  
  

  The main objective is to move 2 VM of the Dell host to the host of Cisco, the reason is because Cisco Support said that the virtual machine requires an Intel and not AMD they are currently.  I currently have a Publisher Cisco Call Manager and Call Manager subscriber residing on the host of Dell, they are constructed (non - OVF) on this machine some time ago.  We started to have problems with them and ultimately Cisco indicated above.

  
  

  A few questions come to mind, can someone please shed some light on them for me?

  1. can I migrate these 2 AMD to Intel VM, without her damage/destruction of the virtual machine?  What that is the answer may be, can you explain to me the why?  The answer to the migration of the CPU is dependent on the guest OS or what?  I ask because I did this successfully on a Windows Guest OS virtual machine, but I guess it is that Cisco makes me hesitate/question.

  2 would it not be better to each virtual machine rebuilt on the new host, rather than through migration for the purposes of the CPU?

  3. What is the recommended method to endorse these VM, before proceeding with the migration?  I'm not talking about save data in the call manager for reasons that I will perform a backup it first.  I ask more along the lines of - for the love of the virtual machine itself.

  1. can I migrate these 2 AMD to Intel VM, without her damage/destruction of the virtual machine?  What that is the answer may be, can you explain to me the why?  The answer to the migration of the CPU is dependent on the guest OS or what?  I ask because I did this successfully on a Windows Guest OS virtual machine, but I guess it is that Cisco makes me hesitate/question.

  You should be able to perform a cold migration. The concern is the guest operating system level.  The Cisco device is probably a Linux distro.  The distribution must use the AMD64 instruction set (Intel 64 compatible) and theoretically should migrate fine.  However, if the guest what OS was improved the AMD CPU instructions, he can expect these features when you restart.  We have at least a virtual computer in our environment that we need to stick to a certain family of Intel processor because the software license dig and binds to it, but this is the only scenario that I have met.

  2 would it not be better to each virtual machine rebuilt on the new host, rather than through migration for the purposes of the CPU?

  I feel better on the redeployment, but if the migration is successful and applications run stable, then you reaped just the benefits of virtualization.

  3. What is the recommended method to endorse these VM, before proceeding with the migration?  I'm not talking about save data in the call manager for reasons that I will perform a backup it first.  I ask more along the lines of - for the love of the virtual machine itself.

  You could do something as simple as the cloning of a copy.  Depending on how you are approved for vSphere, you can have the POS to back up your virtual machine.  You can also use a tool such as VMWare Converter or Veeam Backup and replication. Given the importance of these virtual machines, I would get at least 2 backups of different type.  You should be able to validate any backup with VMWare Workstation prior to migration.