call of CUCM to the router voice FXS thanks CUBE problem
Hello
We had a problem in our test environment:
When we on the g711 codec, both directions of appeal are ok. When we put the codec for g729r8, appeal from analog to IP has no problem. But for reverse, the analog phone can ring but will be disconnected after a few seconds. Before the call is disconnected, we find that the codec is "pre-ietf g729" using the command 'show call active voice brief' on the CUBE. The configuration of the CUBE and Router (FXS) voice is attached. Really appreciate your advice. Thank you! Eric It seems that the analog phone only supports pre - itf g729 format... Unfortunately this codec format is no longer supported on any ios... http://www.Cisco.com/c/en/us/support/docs/voice/h323/14069-codec-complexity.html#pre_ietf You can try your luck and see if this pre - itf is available on ios, but I doubt it. You will need to have them on all your dial peers. The pre-ietf in this command option is not supported in Cisco IOS release 12.2 and later. Tags: Cisco Support Have to disconnect/reconnect to the router I have a clear-cut problem: occasionally, about once a day or two, suddenly I can't load a web page. I can always solve it to disconnect and reconnect to the network, even if it shows me as connected (with five bars). Based on the other computers in the House, I concluded that the router sometimes has a little problem. It shuts off and then on again. Reconnect automatically other computers (ASUS victory 8 machine and my Nexus 7), but mine does not. Any ideas on how to solve this problem? Thank you Al It turned out to be a bad cable modem, which had problems when Suddenlink updated their system. New modem and no problem. Thanks for the help. WAG320N - today's date and time on the router Hello I put restrictions on access to the xbox of my son on my WAG320N. I set the time zone time to GMT and active summer time, but I can't find a screen to actually tell me what the date & time is on the router itself. I had a problem with a previous router where the date & time were automatically to be deregulated and thus access of xbox of my son was off during the wrong time. Does anyone know of a hidden screen where it shows the date & time on the router? Thank you Under the current status tab shows the... The time, based on the time zone selected on the Basic Setup screen, is displayed. WRT600N still cannot connect to the router after factory reset OK, so I reset the router but I can not yet connect to installation using the password factory (admin/admin) (white/admin) (admin/empty). Now, I have a network encrypted and without access to the configuration... I even tried to use the installation CD, but it does not recognize the router. Anyone have this problem or know of a possible fix? Thank you, Carl Hey try resetting the reset button of the router in a way to equip & then connect the power supply to the modem first once all the lights are WRT54GX4 - difficulties to access the configuration Page of the router Web-based WRT54GX4 - difficulties to access the configuration Page of the router Web-based. I have tried all posted to forums and knowledge for several weeks now with no luck. I can feed the router to push and access the router's web-based interface, but only for a few minutes that she was leaving the loading to half way through and or does not load. If I turn on the wireless side I can access the router at will without any problem. My warranty is almost over. I'm at my wits end. I would like to replace it under warranty if I can. (^ 8. Update: I fell up on top of the fix for my problem. After many reconfigurations over the past two months I've tried turn on all newspapers. Since the age of the newspaper I did have a problem of access to my router. I have a home wireless network with a new router Belkin (no separate modem). There are four laptop computers in our House, which connect to the wireless network. One of them is Windows 7, both Vista and the other is XP. Sometimes the internet works perfectly well and all four laptop computers are able to connect simultaneously. But more often... when a new laptop is on and attempts to connect, all current laptops get kicked out of the network all together and are unable to reconnect. The network broadcasts always and appears in the list of available networks, but we are unable to connect. Other times, if my roommate is very well on the internet and I turn on my laptop, I can't see even the network, despite the fact that it is to use! If I turn the router off and on again (sometimes we do this several times) it works OK again. Sometimes this happens several times a day, other times we go days without having to reset. The problems are more frequent when the old Vista laptop is used which is what made me think it may be related to computers (or their settings) rather than the router. Thank you Alex You may need to check every laptop and the router, to be sure. Go to the website of the manufacturer of your Belkin router > make sure you have the latest Firmware for it. Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the. http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems Troubleshoot network adapter problems to Microsoft link above. Try without commitment TCP/IPv6: If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.) http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/ See you soon. Mick Murphy - Microsoft partner Can CCNA configure DSL/PPPoE connection into the router? Let me know CCNA can configure DSL/PPPoE connection into the router? Thank you Hello Contents/chapters/review of CCNA certification change over the years almost on regular basis. What part of the CCNA it a few years ago could already be excluded. This applies to DSL technology. A few years ago, she was part of the CCNA (CCNA4 as subject WAN training programs) related, but this is no longer a part of CCNA. In summary CCNA certified person isn't ready for DSL PPPoE Configuration, as this isn't a part of existing CCNA reading preparation. But I hope that someone who asked the CCNA exam could be so clever, find the corresponding/HOWTO documentation on the internet and be ready for DSL and PPPoE configuration. It is not really difficult to implement that. And at the end - Yes, PPPoE for DSL by CLI configuration on router Cisco is the biggest challenge to do it on the simple one - goal with WebGUI DSL router, but I believe that a new set of commands related to this is not really too difficult to apply and understanding for CCNA certified users. Roads remain in the routing table after disconnecting from the vpn client I am facing this problem for my clients and the easy vpn server. My Cisco 3825 has an easy vpn server configuration with an ip pool. When one of the customer disconnects and isakmp and ipsec his deleted by the router itself. The route pointing to the ip address of the ip pool is still in the routing table. This time, another vpn client connects and get the ip address of the ip even pool. But this new vpn client connected is located on a different interface of the router. Thus, an extreme problem happen! A route to 2 next hops is created! So bad! Someone else can help me? How can I delete the wrong way? Thank you! Jason Lam It can be useful to upgrade because he accompanied several questions IPP in earlier versions of the code with the roads not removed during the SA goes down, etc. IP address of the Sony Bravia TV in collective housing is 1 stop from that used by the router. Address IP of the Sony Bravia TV in collective housing is 1 stop from that used by the router and McAfee network card. TV connects to the router but it says server is not available and cannot access media files. I removed the TV from the group home and now cannot get back at all, even if the NIC McAfee says it's there. How can I return it to the correct IP address? Either by the way TV works well with my laptop and the IP it is in agreement with the router. The Fixit on this link is out of date. However, I did find and try the collective dwelling and routines network Fix - it without success. I used both WIn 7 trouble shooters and they find nothing wrong.
SSL VPN may be configured on the router from Cisco 881/K9? I'm now confused if SSL VPN can be configured on the router from Cisco 881/K9. Please someone advise me. If Yes, for only 5 users, what I need to buy the license or license is supplied with the router? Thank you. Yes, and you need a license: FL-WEBVPN-10-K9 License SSL VPN functionality for up to 10 users (incremental), to 12.4 T based only IOS versions FL-SSLVPN10-K9 License SSL VPN functionality for up to 10 users (incremental) for the only based 15.x IOS versions Re-login C4750 printer to the router problems I have a Linksys WRT54GS router and a printer Photosmart C4750. I initially connected the printer to the wireless network without any problem, but the key to security on the router has been reset and now the printer will not connect. The network test report indicates: "your wireless router requires a WEP security key. The key to security configured on your HP printer does not exactly. "Run the installation of the wireless network for re - enter your WEP wireless network security key. I tried to run the printer setup disk, but ran into a brick wall, when I was given 2 choices. 1. connect wireless ~ the router has not been detected. 2. connect w / USB cable ~ do not have. So I do not know what to do ~ is there a way I can re - enter the security key on the printer using my laptop which is connected wireless to the router? Thanks for any help! First of all, do not use WEP! It is not secure and can also cause connection problems. Use WPA or WPA2 with a password that you create - use 13 + characters, numbers and letters, upper and lower case. In the printer Panel, go to settings (Scan) > networks > reset network by default. Now start the software again for a network installation. Hello What is the procedure to upgrade the call manager since version 7.1 of CUCM (MCS Server) to version 10.2 of CUCM (on the server of the UCS), please let me know the steps to what would be the backup procedures and upgrades. Concerning Gerard I suggest reading this guide to make sure that you have prepared your environment to support the first 10.x. The link below also contains the path to upgrade to 10.0 (1). One of the ways to do this is: 1 / apply cooling cop upgrade file on all servers in the cluster. 2 / upgrade the cluster to 8.6 (2). Make a backup of the cluster. 3 / build a cluster of servers 8.6 (2) on the virtual machines and assign them the same host name and the IP address of the cluster hardware. (You may need to keep these on a separate network until turn off hardware machines) 4 / restoration of the backup of the pile of material on the VM cluster. 5 / upgrade cluster VM to 10.0 (1). http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/CUCM/upgrade/10_0_1/C... Can not connect with the Adobe server to upgrade the PS. Tried with fiervall and the router and called my provider. She is also only CC there are problems! Check your hosts file. help for that and other adobe.com sure common connection problems read, http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html Cannot connect to the router interface because it calls windows security credentials Windows 8 and tries to access my router Web interface and windows security continues to request user name and password. I do not write them and cannot access the router online to make the changes I want to make. Help!!!!!!!!!!!!!!!! BW You must contact your ISP and ask them. You have not even told us what router you have. It adds that the fact that some ISPS do not want to play with the settings of the router means that they are the only ones that can help you. can't make an external call with CuCM and H323 gateway Hi experts, I have a problem with CuCM and h323 Gateway. I use a 2811 router to make a gateway H323, CuCM server and Switch layer 2 build a VoIP LAB, this my network: and my router configuration: Current configuration: 2335 bytes ! version 12.4 horodateurs service debug datetime msec Log service timestamps datetime msec no password encryption service ! router host name ! boot-start-marker boot-end-marker ! forest-meter operation of syslog messages ! No aaa new-model ! ! ! dot11 syslog IP source-route ! ! IP cef DHCP excluded-address 192.168.1.1 IP 192.168.1.10 ! IP VOICE dhcp pool network 192.168.1.0 255.255.255.0 option 150 ip 192.168.1.2 default router 192.168.1.1 ! ! No ipv6 cef ! Authenticated MultiLink bundle-name Panel ! ! voip phone service h323 connections allow h323 allow connections h323 to SIP allow connections sip h323 allow sip to sip connections service additional h450.12 Fax protocol cisco ! ! ! vocal h323 class 1 H225 timeout tcp establish 3 ! ! ! translation of the voice-rule 1 rule 1 / ^ 9. ! ! voice translation-profile PSTN translate 1 called ! ! voice-card 0 ! ! application Service flash aa1: its - cisco.2.0.2.0.tcl paramspace English language en paramspace English index 1 Param aa-driver 0839959204 paramspace location English flash: prefix English paramspace ! ! ! Archives The config log hidekeys ! ! interface FastEthernet0/0 IP 192.168.1.1 255.255.255.0 automatic duplex automatic speed H323-gateway voip interface port of link voip H323-gateway 192.168.1.1 ! interface FastEthernet0/1 no ip address Shutdown automatic duplex automatic speed ! IP forward-Protocol ND no ip address of the http server no ip http secure server ! ! ! control plan ! ! ! voice-port 0/0/0 cover of the echo - cancel 32 connection ERA opx 3100 Description 08395959204 activation of the caller ID ! voice-port 1/0/0 ! voice-port 0/0/2 ! voice-port 0/0/3 ! ! ! 1010 Dial-peer voice pots Service aa1 incoming called number 08395959204 direct line to inside port 0/0/0 ! voice pots Dial-peer 2020 PSTN description translation-profile outgoing PSTN destination-model 9 t Setup progress_ind allow 3 progress_ind enable progress 8 port 0/0/0 Forward-digits all the ! Dial-peer voice 10 voip destination-model 1... Setup progress_ind allow 3 progress_ind enable progress 8 h323 voice-class 1 session target ipv4:192.168.1.2 DTMF-relay h245 alphanumeric Codec g711ulaw No vad ! ! ! ! Line con 0 line to 0 line vty 0 4 Cisco password opening of session ! Scheduler allocate 20000 1000 end I have configured the gateway h323 and attach files to router parttern on follow CUCM What is the problem and how to solve? Thanks for all the help. Your DP pointing CUCM is wrong, or your ÉRA OPX, depending on what you need. voice-port 0/0/0 cover of the echo - cancel 32 connection ERA opx 3100 Description 08395959204 activation of the caller ID Dial-peer voice 10 voip destination-model 1... Setup progress_ind allow 3 progress_ind enable progress 8 h323 voice-class 1 session target ipv4:192.168.1.2 DTMF-relay h245 alphanumeric Codec g711ulaw
No vad Your DP is waiting for 1... and you send 3100, they must match. You might need to change the significantt numbers and entering CSS, but only you can know For outgoing, you are throwing 9 predot, but again, expect it in your RFP, again, change as you need. voice pots Dial-peer 2020 PSTN description translation-profile outgoing PSTN destination-model 9 t Setup progress_ind allow 3 progress_ind enable progress 8 port 0/0/0 Forward-digits all the You cannot transfer the numbers all send you also 9 for each call
Change your configuration you want / need. HTH Java If it helps, please note How to configure microsoft exchange account How to configure Microsoft Exchange account on iPhone. I'm getting a problem while creating a Microsoft Exchange account on the iPhone. Can any body tell me How to set up a mail in iPhone because I want to set up an account for Microsoft exchange on How to get the tools/preferences to open in a new window? It appears like 42.0 you can have is no longer a good pop-up for the 'preferences', unfortunately, this means that it opens in a tab. How do you define on it to open it in a new window (not in a new tab)? Also, where the other color is defined the co Why some emails do not disappear while I'm writing them? Several times recently, I was about to send an email when he disappeared from my screen, even if the program is still open. The last time this happened I tried the back button and a message on security and the server.Anyone had a similar experience. How to change the style of letter and size on the Thunderbird page On my homepage of Thunderbird, I want to change the letter format and style. Not in the new section of e-mail letters. The e-mails contained in the subject. Thank you Why windows live Director has no timeline functionality? This makes it extremely difficult/impossible to produce separate audio / subtitles for your videos maui-vgw-01(config)#dial-peer voice 100 voip maui-vgw-01(config-dial-peer)#codec g729r8 pre-ietf
Similar Questions
TouchSmart HP Envy 17
Windows 10 worm 1607
light flashes on the router & then make a full of electric network
cycle that is, unplug the power to the modem & router cables
Green, you can plug the power cable to the router & discover
This will definitely work!
Maybe you are looking for