'call send DTMF' of the CTS
Anyone know the syntax of this CLI command without papers? One can understand...
Hello
SYNTAX:
call send DTMF {Arg0} {Arg1}
DESCRIPTION:
Arg0 - mandatory
Caller ID for which send the DTMF signal
Arg1 - mandatory
DTMF to send signal
Example, here you are...:
1. start the call:
Admin:call start 112284021490001
2. once the call is set up check Call command ID:
Status of the call admin:Show
Call status
Recorded in Cisco Unified Communications Manager: Yes
Call connected: Yes
Type of call: call Audio only call start time: 19 09:39:27 Feb 2014
Duration (sec): 15 Direction: outgoing
Local number: 112284031421006 remote number: 112284021490001
Status: answered
Security level: unsecured call Id: 3
3 send DTMF command:
Admin:call send DTMF 3 53921568
Send dtmf signals... FACT
Admin:
Concerning
Marek
Tags: Cisco Support
Similar Questions
-
[CME 9.1] Phone IP 3905 fails to send DTMF tones to the external network.
Hi all!
We have three types of SIP phones in our CME 9.1: 3905, 6941 and 8941. All phones except 3905 send DTMF tones successfully through our operator. Here is "debug voice ccapi detail" what "206" (ip phone 3905) extension 93274343 external phone calls and trying to send numbers. Config is to be attached. Also, a part of config here:
voip phone service
list of approved IP addresses
IPv4 10.0.0.0
h323 connections allow h323
allow connections h323 to SIP
allow connections sip h323
allow sip to sip connections
service additional h450.12
no additional service moved temporarily sip
no service additional sip refer
Fax protocol t38 ls-redundancy version 0 0 hs-redundancy 0 help none
H323
SIP
Registration Server expires 120 min 60 max
!
voice class codec 1
g711ulaw codec preference 1
g711alaw preferably 2 codec
!
!
Global voice registry
FMC of fashion
source-address 10.10.0.41 port 5060
3 timeouts interdigit
Max - dn 100
Max-pool 80
load 8961 sip8961.9 - 2 - 2 SR 1-9
authenticate the registry
authenticate the defagroup.com Kingdom
time format 24
date format D/M/Y
Flash TFTP-path:
create the profile synchronization 0001013651736503
Hi all!
We have three types of SIP phones in our CME 9.1: 3905, 6941 and 8941. All phones except 3905 send DTMF tones successfully through our operator. Here is "debug voice ccapi detail" what '206' extension 93274343 external phone calls and trying to send numbers. Config is to be attached. Also, a part of config here:
voip phone service
list of approved IP addresses
IPv4 10.0.0.0
h323 connections allow h323
allow connections h323 to SIP
allow connections sip h323
allow sip to sip connections
service additional h450.12
no additional service moved temporarily sip
no service additional sip refer
Fax protocol t38 ls-redundancy version 0 0 hs-redundancy 0 help none
H323
SIP
Registration Server expires 120 min 60 max
!
voice class codec 1
g711ulaw codec preference 1
g711alaw preferably 2 codec
!
!
Global voice registry
FMC of fashion
source-address 10.10.0.41 port 5060
3 timeouts interdigit
Max - dn 100
Max-pool 80
load 8961 sip8961.9 - 2 - 2 SR 1-9
authenticate the registry
authenticate the defagroup.com Kingdom
time format 24
date format D/M/Y
Flash TFTP-path:
create the profile synchronization 0001013651736503
Register of voice dn 6
number 204
call-forward noan 201 timeout 20 b2bua
Register of voice model 1
function key 1 Redial
function key 2 Cfwdall
function key 3 Hold
function key 5 Trnsfer
function key 6 DND
!
voice dialing plan registry 1
type of 7940-7960-others
model 1...
2 9810 model *.
model 3 9...
Model 4 98...
Register of voice pool 8
Mac ID 64D8.14A5.01B4
type of 3905
Number 1 dn 8
numbering plan 1
DTMF-relay rtp - nte
codec voice-class 1
206 206 username password
No vad
voice POTS dial-peer 1
translation-profile out in the city
destination-model 9 t
port 0/0/0:15
Retail ccapi voice 'debug' is here:
phone #.
* Dec 27 16:45:22.095: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:22.095: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:22.095: / / 817/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:22.095: / / 817/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:22.095: / / 817/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:22.095: //-1/xxxxxxxxxxxx/CCAPI/cc_api_update_interface_cac_resource:
Hwidb = GigabitEthernet0/0, bandwidth = 80, Call Id = 817
* Dec 27 16:45:22.095: //-1/xxxxxxxxxxxx/CCAPI/cc_api_update_interface_cac_resource:
Call total count = 0, call Voip Count = 0, Count MMoip call = 0 x 0, bandwidth = 80
* Dec 27 16:45:22.095: / / 817/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:22.095: / / 817/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:22.095: //-1/A3B9036582FD/CCAPI/cc_api_call_setup_ind_common:
Interface type = 0, Protocol = 3
* Dec 27 16:45:22.095: //-1/A3B9036582FD/CCAPI/ccCheckClipClir:
Part number is provided by the user
* Dec 27 16:45:22.095: //-1/A3B9036582FD/CCAPI/cc_api_call_setup_ind_common:
After checking the number translation:
Number = 206 (TON = unknown, NPI = unknown, not projected = screening, presentation = authorized),
Called number = 3 (TONNE = unknown, NPI = unknown)
* Dec 27 16:45:22.095: / / 817/xxxxxxxxxxxx/CCAPI/cc_insert_call_entry:
Total Call Count = 0, entry calls (call count On = FAKE incoming call = TRUE)
* Dec 27 16:45:22.095: / / 817/xxxxxxxxxxxx/CCAPI/cc_insert_call_entry:
Total Call Count = 1
* Dec 27 16:45:22.095: / / 817, A3B9036582FD, CCAPI, cc_insert_guid_pod_entry:
Incoming = TRUE, Call Id = 817
* Dec 27 16:45:22.095: / / 817, A3B9036582FD, CCAPI, cc_incr_if_call_volume:
10.10.0.126 = remote IP address, Hwidb = GigabitEthernet0/0
phone #.
* Dec 27 16:45:22.095: / / 817, A3B9036582FD, CCAPI, cc_incr_if_call_volume:
Call count total = 1 call Voip Count = 1, Call MMoip Count = 0
* Dec 27 16:45:22.099: //-1/xxxxxxxxxxxx/CCAPI/cc_setupind_registration_lookup:
Corresponding settings; Called number = 3, call transfer Consult Id =
* Dec 27 16:45:22.099: //-1/xxxxxxxxxxxx/CCAPI/cc_setupind_registration_lookup:
No matching node
* Dec 27 16:45:22.099: / / 817, A3B9036582FD, CCAPI, cc_api_set_transfer_info:
Call transfer Reset
* Dec 27 16:45:22.443: / / 817, A3B9036582FD, CCAPI, ccCallDisconnect:
Start calling accounting;
Call Entry (Incoming = TRUE)
* Dec 27 16:45:22.443: / / 817, A3B9036582FD, CCAPI, ccCallDisconnect:
Value = 28, entry calls (disconnect the Cause = 0)
* Dec 27 16:45:22.443: / / 817, A3B9036582FD, CCAPI, cc_api_update_interface_cac_resource:
Hwidb = GigabitEthernet0/0, bandwidth =-80, Call Id = 817
* Dec 27 16:45:22.443: / / 817, A3B9036582FD, CCAPI, cc_api_update_interface_cac_resource:
Call count total = 1 call Voip Count = 1, Call MMoip Count = 0x0, bandwidth = 0
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, cc_decr_if_call_volume:
10.10.0.126 = remote IP address, Hwidb = GigabitEthernet0/0
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, cc_decr_if_call_volume:
Call total count = 0, call Voip Count = 0, Call MMoip Count = 0
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, cc_delete_guid_pod_entry:
Incoming = TRUE
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, cc_delete_call_entry:
Total Call Count = 1, entry calls (call count On = FAKE incoming call = TRUE)
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, cc_delete_call_entry:
Total Call Count = 0
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, cc_delete_call_entry:
Removal of profileTable [0x336F00D4]
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, ccCallGetVoipFlag:
Mask of data bits = 0 x 2, Call Id = 817
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, ccCallGetVoipFlag:
Flag = FALSE
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, ccCallSetVoipFlag:
telephony #Flag = FALSE, data bits mask = 0 x 2, call Id = 817
* Dec 27 16:45:22.559: / / 817, A3B9036582FD, CCAPI, ccCallSetVoipFlag:
Call the entry (Voip AAA Flags = 0x0)
* Dec 27 16:45:22.559: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
phone #.
* Dec 27 16:45:28.995: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:28.995: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:28.995: / / 818/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:28.995: / / 818/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:28.995: / / 818/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:28.995: //-1/xxxxxxxxxxxx/CCAPI/cc_api_update_interface_cac_resource:
Hwidb = GigabitEthernet0/0, bandwidth = 80, Call Id = 818
* Dec 27 16:45:28.995: //-1/xxxxxxxxxxxx/CCAPI/cc_api_update_interface_cac_resource:
Call total count = 0, call Voip Count = 0, Count MMoip call = 0 x 0, bandwidth = 80
* Dec 27 16:45:28.995: / / 818/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:28.995: / / 818/xxxxxxxxxxxx/CCAPI/cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:28.995: //-1/A7D5DC978303/CCAPI/cc_api_call_setup_ind_common:
Interface type = 0, Protocol = 3
* Dec 27 16:45:28.995: //-1/A7D5DC978303/CCAPI/ccCheckClipClir:
Part number is provided by the user
* Dec 27 16:45:28.995: //-1/A7D5DC978303/CCAPI/cc_api_call_setup_ind_common:
After checking the number translation:
Number = 206 (TON = unknown, NPI = unknown, not projected = screening, presentation = authorized),
Called number = 9 (TON = unknown, NPI = unknown)
* Dec 27 16:45:28.995: / / 818/xxxxxxxxxxxx/CCAPI/cc_insert_call_entry:
Total Call Count = 0, entry calls (call count On = FAKE incoming call = TRUE)
* Dec 27 16:45:28.995: / / 818/xxxxxxxxxxxx/CCAPI/cc_insert_call_entry:
Total Call Count = 1
* Dec 27 16:45:28.995: / / 818/A7D5DC978303/CCAPI/cc_insert_guid_pod_entry:
Incoming = TRUE, Call Id = 818
* Dec 27 16:45:28.999: / / 818/A7D5DC978303/CCAPI/cc_incr_if_call_volume:
10.10.0.126 = remote IP address, Hwidb = GigabitEthernet0/0
phone #.
* Dec 27 16:45:28.999: / / 818/A7D5DC978303/CCAPI/cc_incr_if_call_volume:
Call count total = 1 call Voip Count = 1, Call MMoip Count = 0
* Dec 27 16:45:28.999: //-1/xxxxxxxxxxxx/CCAPI/cc_setupind_registration_lookup:
Corresponding settings; Called number = 9, call transfer Consult Id =
* Dec 27 16:45:28.999: //-1/xxxxxxxxxxxx/CCAPI/cc_setupind_registration_lookup:
No matching node
* Dec 27 16:45:28.999: / / 818/A7D5DC978303/CCAPI/cc_api_set_transfer_info:
Call transfer Reset
phone #.
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_validate_mlpp_info:
VALIDATION MLPP INFO:-ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [0 (INTERNAL_PRECEDENCE_0)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_is_precedence_mlpp_info:
Priority no more than Routine
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_copy_mlpp_info:
Before COPYING - CBC MLPP INFO: ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [0 (INTERNAL_PRECEDENCE_0)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_copy_mlpp_info:
DEST MLPP INFO: ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [0 (INTERNAL_PRECEDENCE_0)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_copy_mlpp_info:
AFTER COPY - CBC MLPP INFO: ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [0 (INTERNAL_PRECEDENCE_0)] DEST MLPP INFO: ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [-1 (PRECEDENCE_LEVEL_NONE)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_copy_mlpp_info:
Before COPYING - CBC MLPP INFO: ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [0 (INTERNAL_PRECEDENCE_0)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_copy_mlpp_info:
DEST MLPP INFO: ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [-1 (PRECEDENCE_LEVEL_NONE)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_copy_mlpp_info:
AFTER COPY - CBC MLPP INFO: ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [0 (INTERNAL_PRECEDENCE_0)] DEST MLPP INFO: ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [-1 (PRECEDENCE_LEVEL_NONE)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_validate_mlpp_info:
VALIDATION MLPP INFO:-ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [0 (INTERNAL_PRECEDENCE_0)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_is_precedence_mlpp_info:
Priority no more than Routine
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_validate_mlpp_info:
VALIDATION MLPP INFO:-ServiceDomain: [no (0)] DomainIdentifier: [000000] PrecedenceLevel: [-1 (PRECEDENCE_LEVEL_NONE)] NormalizedPrecedence: [-1 (PRECEDENCE_LEVEL_NONE)]
* Dec 27 16:45:34.827: //-1/xxxxxxxxxxxx/CCAPI/cc_is_precedence_mlpp_info:
Priority no more than Routine
* Dec 27 16:45:34.827: / / 818/A7D5DC978303/CCAPI/ccCheckClipClir:
Part number is provided by the user
* Dec 27 16:45:34.827: / / 819/xxxxxxxxxxxx/CCAPI/cc_insert_call_entry:
Total Call Count = 1, entry calls (call count On = FAKE incoming call = FALSE)
* Dec 27 16:45:34.827: / / 818/A7D5DC978303/CCAPI/cc_peer_bind:
Link = TRUE, Id = 818, bound Call Id = 819 Call Binder
* Dec 27 16:45:34.827: / / 819, A7D5DC978303, CCAPI, cc_insert_guid_pod_entry:
Incoming = FALSE, Call Id = 819
phone #.
* Dec 27 16:45:34.827: / / 819, A7D5DC978303, CCAPI, cc_set_voice_port_value:
CC_IF_TELEPHONY: Echo = 0, = 0 Playout
* Dec 27 16:45:34.831: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:34.831: / / 818/A7D5DC978303/CCAPI/ccCallGetContext:
Context = 0x33C6F520, Id = 818 Call
* Dec 27 16:45:34.831: //-1/xxxxxxxxxxxx/CCAPI/cc_set_outpulsed_digits:
set 3274343 = outpulsed_dialstring
* Dec 27 16:45:35.399: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:35.399: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
* Dec 27 16:45:35.403: / / 818/A7D5DC978303/CCAPI/cc_peer_bind:
phone #Bind = TRUE, Binder Call Id = 818, bound Call Id = 819
* Dec 27 16:45:35.559: / / 818/A7D5DC978303/CCAPI/cc_peer_bind:
Link = TRUE, Id = 818, bound Call Id = 819 Call Binder
phone #.
* 16:45:45.199 Dec 27: % LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0:14, status changed to
phone #.
* Dec 27 16:46:02.215: / / 818/A7D5DC978303/CCAPI/ccCallDisconnect:
Start calling accounting;
Call Entry (Incoming = TRUE)
* Dec 27 16:46:02.215: / / 818/A7D5DC978303/CCAPI/ccCallDisconnect:
Value = 16, entry calls (disconnect the Cause = 16)
* Dec 27 16:46:02.215: / / 818/A7D5DC978303/CCAPI/ccCallDisconnect:
Call the entry (disconnect the Cause = 16)
* Dec 27 16:46:02.215: / / 819, A7D5DC978303, CCAPI, ccCallDisconnect:
Start calling accounting;
Call Entry (Incoming = FALSE)
* Dec 27 16:46:02.215: / / 819, A7D5DC978303, CCAPI, ccCallDisconnect:
Value = 16, entry calls (disconnect the Cause = 0)
* Dec 27 16:46:02.215: / / 818/A7D5DC978303/CCAPI/cc_api_update_interface_cac_resource:
Hwidb = GigabitEthernet0/0, bandwidth =-80, Call Id = 818
* Dec 27 16:46:02.215: / / 818/A7D5DC978303/CCAPI/cc_api_update_interface_cac_resource:
Call count total = 1 call Voip Count = 1, Call MMoip Count = 0x0, bandwidth = 0
* Dec 27 16:46:02.227: //-1/A7D5DC978303/CCAPI/g113_calculate_impairment:
(delay = 79 (ms), loss = 0%), Qi = 0 participants Io = 0 = 0 = 2 Ie = - 1 Itot = 1 DLI
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/cc_decr_if_call_volume:
10.10.0.126 = remote IP address, Hwidb = GigabitEthernet0/0
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/cc_decr_if_call_volume:
Call total count = 0, call Voip Count = 0, Call MMoip Count = 0
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/cc_delete_guid_pod_entry:
Incoming = TRUE
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/cc_delete_call_entry:
Total Call Count = 1, entry calls (call count On = FAKE incoming call = TRUE)
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/cc_delete_call_entry:
Total Call Count = 0
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/cc_delete_call_entry:
Removal of profileTable [0x336EFA6C]
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/ccCallGetVoipFlag:
Mask of data bits = 0 x 2, Call Id = 818
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/ccCallGetVoipFlag:
Flag = FALSE
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/ccCallSetVoipFlag:
telephony #Flag = FALSE, data bits mask = 0 x 2, call Id = 818
* Dec 27 16:46:02.227: / / 818/A7D5DC978303/CCAPI/ccCallSetVoipFlag:
Call the entry (Voip AAA Flags = 0x0)
* Dec 27 16:46:02.227: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
* Dec 27 16:46:02.275: / / 819, A7D5DC978303, CCAPI, cc_delete_guid_pod_entry:
Incoming = FALSE
* Dec 27 16:46:02.275: / / 819, A7D5DC978303, CCAPI, cc_delete_call_entry:
Total Call Count = 0, entry calls (call count On = FAKE incoming call = FALSE)
* Dec 27 16:46:02.275: / / 819, A7D5DC978303, CCAPI, cc_delete_call_entry:
Removal of profileTable [0x336E75C4]
* Dec 27 16:46:02.275: / / 819, A7D5DC978303, CCAPI, ccCallGetVoipFlag:
Mask of data bits = 0 x 2, Call Id = 819
* Dec 27 16:46:02.275: / / 819, A7D5DC978303, CCAPI, ccCallGetVoipFlag:
Flag = FALSE
* Dec 27 16:46:02.275: / / 819, A7D5DC978303, CCAPI, ccCallSetVoipFlag:
Flag = FALSE, data bits mask = 0 x 2, Call Id = 819
* Dec 27 16:46:02.275: / / 819, A7D5DC978303, CCAPI, ccCallSetVoipFlag:
Call the entry (Voip AAA Flags = 0x0)
* Dec 27 16:46:02.275: / / 0, xxxxxxxxxxxx, CCAPI, cc_get_call_entry:
Entry call is not found
phone #unde all
The CME version is 9.1
Version of the IOS is 15.3 (1) T (also tested in 15.2 - the same issue)
All ip phones have the last firware (9-2-2-0), also I have already spent some of them (9-2-1-0) - the problem persists.
Hello
I think the best is to capture a trace of sniffer on the phone directly, we will be able to see if the phone itself sends the numbers.
You can also enable some debugs:
Deb voice ccapi inout
messages ccsip deb
Media ccsip deb
That should be enough to isolate the problem
--
Jorge ArmijoDo not forget to rate helpful responses and identify useful or correct answers.
-
Asked to make calls and send pictures at the same time. Possible?
Hello
its my first post here. I have very little experience working with BlackBerry. I've been playing with 9800 Simulator and some samples provided with IDE 6.0, I serched for slution to my problem with no luck.
My question is: is at - there a Posibility to make an app, that would have a built-in single-list contacts with multiple phone numbers, will allow to call (with a built-in list contact phone numbers by pressing a button) and take pictures and email them during this call?
App like this is a request for a doctor - it needs to be as user-friendly as possible, the person who has never used a Blackberry phone should be able to make calls and send photos. The idea is that a doctor during a call with another doctor would be able to take a picture and send it to the person he calls (or other) in order to consult.
If my explanations are confusing, I will try to write differently.
Thanks in advance.
I am not the best person to answer, but if I understand correctly, simultaneous data and voice is possible, but depends on carrier and the type of wireless connection you - I think you need 3 g to do. With this reservation, it seems possible to what you are suggesting.
-
Can what method/class/object I use to send data to the form variable to BradySoft? I have a basic configuration of BradySoft label and I want to send it data of variable shape (a serial number) from Labview ActiveX. I joined guide Brady ActiveX programmers, but can't understand what to use for that.
P.S. I would call Brady or TekLynx tech support on this issue, but they have a strict policy while BradySoft supports ActiveX, but does not provide technical support assistance programming with it. I thought I would try the Forums OR.
Just an update. I could get this to work myself after a few days of playing with it (I suppose that the best way to learn!). I have attached a sample VI for anyone interested. Can we Kudo ourselves?
-
Summary of the issue
Send/receive email problemPlease provide your address affected:
E-mail address is removed from the privacy *.
Additional detailsI recently set up my X - Box Live ID girls and attached it to my profile as a child account. For some reason, I had to create a new account, for its xbox live and link it to a hotmail account. I put in place that e-mail as a child and linked to my email account * address email is removed from the privacy * I think was the name of the child account * address email is removed from the privacy * or live.com. I don't know if what I feel is due to this link/link.
What I feel is the following: my junk e-mail folder is no longer visible in my folder list. I get a lot of spam, but I've been at some point receive unwanted emails from an email address that said of * address email is removed from the privacy *, which is of course MY e-mail address. When I opened the email there is a link, but it wasn't an email I sent. I'm not stupid enough to click on this link, then I looked at the headers. But I just looked to see if I saved them to my computer or not. I can't locate copy this email, because they are stored in my spam box, and I don't have the option more to click on it. I regularly send myself emails with reminders to myself, so I don't know if I've inadvertently admitted someone access to spoil my account, or if I made a mistake in the process, I took.
Basically when I try to send email he gave me an error message that says that I could not send to sources outside my list of contacts, because of settings parents. However, this has been my email for a long time now, and I'm 30 years old and never had this problem before. I looked under related accounts, thinking somehow that connection could be causing it. I deleted my account my e-mail girls. After that I am more able to see my box of junk e-mail, or send email to anyone outside of my lists of contacts.
I looked through all the settings that I could and connected with my info, but it had no effect. I need to know what is happening with my account, and I need to have this resolved. I'm not able to receive emails, so if I don't hear from you, please use email from my wife who is * address email is removed from the privacy *, or call me at the 623-418-7466. If this can be resolved without further communication, it would be better, but I'll check everything that I need to in order to get this resolved.Thank you very much for your support,
Andrew M. JonesADDED: I've already entered my settings and provide my date of birth 29/09/1981. I took this step because of a closely similar thread that had this step for a fix. There was still no change after this action. I could check my emails, because I can send one to the internet provider of the e-mail, I found in the header. So I found the file headers and I tried to add to this email, but he crossed the line.
Hi, Andrew Jones,.
After reviewing your question and account again, I checked that your e-mail address, is the story of the child of email from your daughter. You can remove it by following these steps:
1. go to the Family Safety Web Site with your daughter account (as is the current parent account).
2. under family summary, click Remove a member of the family.
3. check or tick the box next to the account name.
4. click on Remove.
5. a dialog box appears, click Remove.
6 sign out. you of the Family Safety website.In case that the website redirects you to download the parental control, please download and install on your computer. Then, access the website again.
Thank you
B. Litton -
When I send pdf files the recipients using aol receive a file "WinMail" they can't open.
When I send pdf files the recipients using aol receive a file "WinMail" they can't open.
I have my mail format HTML the value and we tried also plain text without change.
What email program are you using?
Assuming that Outlook 2010 or Outlook 2007, try the following article:
"When you use Outlook 2010 or Outlook 2007 to send an e-mail message, the recipient of the message sees an attachment called Winmail.dat"
<>http://support.Microsoft.com/kb/958012 >HTH,
JW -
How to send images from the photo library
don't know how to do for the form by e-mail photos picture library
This depends on your e-mail program. Open your program and create a new email. Select an item called "Send a file" or similar. Access your photos, select those that you want to send. Now your photos will be sent as an attachment when you send this e-mail.
If not, right-click on the image you in the library, select ' send to ' and then 'recipient '.
All the answers and suggestions are provided by an enthusiastic amateur and are therefore no explicit or implicit guarantee. Basically, you use my suggestions at your own risk.
-
Hello..
I have the next guy... I have to do an application what to do a procedure in a PBX.
at this moment the PBX have a Pentecost function that I can make a call and type a few keys send numers o a break... DTFM tones... and this Pentecost keys I program the PBX.
so, how do I do an application what some call to PBX in the background and send DTFM tones to make the program in the PBX?
Read this thread, it might be useful
http://supportforums.BlackBerry.com/T5/Java-development/sending-DTMFTones/m-p/557180#U557180
-
How do I know if a call is disconnected by the user or by the appellant?
When there is an incoming call, the phone user can log out by clicking on the red button, or it can be cut by the appellant. I must say that out of these two types.
But no matter how the call is interrupted, the system continues to produce a callDisconnected event.
Also, I tried to save an event key listener to monitor the events of the red button. But as the system have consumed the event, the system will not send this event of red button at my request.
Do you have an idea how know if a call to imcomming is disconnected by the user or by the appellant?
I tried, although the keydown event of the red button has been consumed by the system, but the keyup event is still distributed, so that the application can listen to the event keyup to know if the call is interrupted by the appellant or by user.
-
ISDB or Original called number used by the unit?
Hi all - I wonder if you can help on something I'm confused in the course.
When a call comes in the unit - which field unit uses to know what Voicebox to send the call to? And is there anyway to change the unit of it used the ISDB in the called party, or vice versa?
Any information is appreciated.
Kind regards
Stuart
When a call forward in unity, we get the latest issue of redirect from the TSP and it's that unity uses to search for box or voice call manager and load the greeting appropriate there. For a direct call in the call number is passed to us and we will try so connect to the mailbox assigned to this number (as applicable).
You can use the call Viewer application in the warehouse of tools to see what values are passed to us in different scenarios.
Currently, you cannot force a different value (i.e. the first number redirection on a forward or similar).
-
encrypt/decrypt in Oracle Forms BEFORE you call an SP or the database DML statement
Hello. I'm working on an application where we need to encrypt information before it is sent to the database. I know that the database has a great set of stored procedures to manage the encryption and decryption. The only challenge here is the fact that I would need to send information unencrypted in the database "in the clear". Ideally, I would like to encrypt the information in the form and send it to the database. On recovery, recover the information and then have the application forms decipher encrypted information.
Whoever did this as a package within a PLL without all calls to a package DBMS_?
Thank you
BradW
OK, I think I have the solution. We are going to import a java class that we create to do this for us. We then import it in forms in a library of PLL. Problem solved!
Nice little intro to importing Java can be found here:
Java in Oracle Forms without beans and pluggable Java components
-
Calling a function in the HTML window that course is located inside - 8 Captivate
Hello
I scoured the forums to answer this but still have developed in white.
Our LMS is launching a course in a pop-up window and inside that the Captivate output file .htm lies.
Currently this pop-up window has a button that performs a function. The problem is this button is rather unsightly sitting above the price in the HTML window and I wish I could call this function inside the Captivate course itself.
The function is called closeSCOContent() and it closes the window of course but basically sends the user to a page of comments.
So, basically is it possible to call this function using the Javascript function in Captivate 8?
I hope that I have explained that sufficient
Thank you very much!
You should be able to call the function, but you would need to know where he is regarding parents/children/opener. Looks like there's frameset inside the popup.
-
Problem with sending data to the Php Mail Script.
So, I work with this Flash pattern that my boss bought. It has a contact form, you are supposed to be able to fill, and he sent an e-mail to a specified address.
However, it does not work. Not at all!
There are 4 fields on the form
name
E-mail
Phone
Message
The Code for the button send is
-Code button-
onClipEvent (load) {this.t.v = _root.contacts_txt7 ;}
on (rollover) {this.gotoAndPlay ("s1") ;}
(deployment) {this.gotoAndPlay ("s2") ;}
{We (Release)}
_parent.loadVariables ("inc/mail.php", "POST");
}
-Code button-
The php script is
Php script-
<?
$name = $_POST ['name'];
$email = $_POST ['email'];
$phone = $_POST ['phone'];
$message = $_POST ['message'];
$ToEmail = "email@here";
$ToSubject = 'the message of your site;
$EmailBody = "name: $name\n".
E-mail: $email\n
Phone: $phone\n
"Message: $messages\n";
$Message = $EmailBody;
$headers. = "content-type: text; charset = iso-8859-1\r\n ";
$headers. = « de : ". $nom. « / ». $email. » \r\n » ;
mail ($ToEmail, $ToSubject, $Message, $headers);
? >
Php script-
It seems like it should work. The mail on the server function works, as I am able to set up a base in php contact page and it works, however, he wants that this flash contact form. It's as if the flash does not send anything to the php script. Is there something missing? I have looked for hours and have resorted to hitting my head on the wall, in an effort to jar loose ideas, so far, nothing.
1. don't set the $ToEmail variable
2. I do not see where $headers is initialized
3. what directory (relative to the html embed your swf) contains mail.php and
4. use tracking feature to ensure that these variables (name, etc.) are set to _parent when your php file is called.
-
callAS() speak only for the first Flash-RMA resources
Hello
I use sovereign wealth funds as interfaces to manipulate 3D annotations. This requires an interaction between the RMA ActionScript and acrobats JavaScript using the ExternalInterface class provided by Flash. When Nicole a method AS to JS I use
this.getAnnotsRichMedia (0) [0] .callAS ('methodname');
It works great so far. I can call all the methods a single SWF exposed via the ExternalInterface.
But now a more complex situation has developed. It forces me to use multiple SWF files for a 3D annotation. However, I can only use callAS to call the first swf I added. If I remove it, the following will take his place. I suspect that the resources are treated in a table, and callAS will never attack the first flash element, he meets. Is it possible to address specific SWFs in the resources of the RMA?
I already tried a kind of call-to-all-broadcasting, giving each swf AS-method with the same name, but it is still only performed by the first SWF (not quite a surprise).
FlashMovie.call () does not work, but you NEED at least to send a parameter (so your AS function should accept one of the same type).
For example, if the function exposed by ExternalInterface AS3 is
function sayHello(_str:String):void {}
then you can call in your 3D JS
myFlashMovie.call ("sayHello", "and goodbye");
BUT if your AS3 is
function sayHello (): void {}
or
function sayHello(_str:String):void {}
then a 3D JS call to
myFlashMovie.call ("sayHello");
or
myFlashMovie.call("sayHello",true,123);
will fail.
The return value of the function AS3 any - if it is canceled or not, you'll see always "indefinite" in response to a call().
Yes, I should have explained somewhere many years ago... but now, you know.
If you want to send on any code or discuss in detail, PM me.
-
Send attachments using the utl_smtp
Hello
How can I use UTL_SMTP to send a file generated by email as an attachment. I created a MS Excel spreadsheet on an application server. I would send it as an attachment to the recipients.
OneWay is to use the uuencode in UNIX script.
But I wanted it to be sent using UTL_SMTP. Could someone please suggest a good direction?
Thank you
UDsUDs wrote:
How can I use UTL_SMTP to send a file generated by email as an attachment.
You can not. Wrong question. SMTP is a protocol for transfer as Simple Mail Transfer Protocol. Its only purpose is to take a completed email, you connect to a mail server and forward this email to the e-mail server for delivery.
It's like a freight delivery truck. He doesn't have the cargo. In other words, it does not build an email duly filled out for your.
You must move the cargo to SMTP for delivery via the SMTP DATA command. The cargo in this context must be a valid MIME (Multipurpose Internet Mail Extensions) body.
The body contains two main parts. The header that contains data such as the subject of the e-mail, the type of mail and so on. Followed by the body that contains the actual e-mail content, including all attachments.
I suggest you read the Wikipedia link, I have provided as it explains a lot of what a MIME body is, with references to memos RFC (Request For Comments) that governs the MIME standards.
With Oracle 10.2 and later versions, a package called UTL_MAIL PL/SQL is provided which creates a MIME body for you - that oppose you create one manually for UTL_SMTP. However, UTL_MAIL is a bit primitive, as it supports only one attachment.
I created a MS Excel spreadsheet on an application server.
If it resides on the application server, then it must be transported to the layer of database for delivery by e-mail. Wouldn't it be faster to just send it via the application server itself? Unless of course it must be stored at the level of the db in all cases.
Maybe you are looking for
-
Used tbird for my gmail for years without problem. Uninstalled Chrome the browser and suddenly tbird became a message "connection refused". Tried everything. Completely uninstalled/reinstalled TBird. It made no difference. I have a user name or incor
-
I need a copy of the iDVD themes folder. Can anyone help?
After changing my hard drive after a failure, I managed to copy all my stuff more, or so I thought. When I open iDVD, the application asks me to find the folder "themes." I don't have it. Apple no longer support iDVD so I was wondering if someone cou
-
Connect a to a USB MS receiver Logitech K520 wireless keyboard and a MS Wireless Mobile Mouse 4000
Is it possible to connect a keyboard to a receiver USB MS Logitech K520 wireless and a MS Wireless Mobile Mouse 4000... all performed on a Toshiba Satellite L455 with Windows 7 Home Premium? The wireless mobile mouse works, because she and the USB re
-
Serial number Photoshop elements 14
HelloI'm having trouble accessing my serial number when I type in my code in a store buying a license of the software.It is saying that my number is not valid.Any help would be greatly appreciated, thank you.
-
ViewObject get attribute always returns null
Hi guys,.I need your help, I'm going crazy.I'm just trying to browse a ViewObject as I did a thousand times but despite getEstimatedRowCount return 1 and the Row inside the SENTENCE object is not null, getattribute always returns null, does not care