camera to trigger external AVT timeout error

Hello forum,.

I have external trigger problems for work to the MAX with my AVT F032BC camera Pike.   I was able to get the camera both in labview and MAX (at 800mbps using firewire 1394b) using software release, but I can't get the switch to work.  Whenever I try random configurations in MAX to trigger mode (mode of 0.1, 15; and each setting relaxing high or low), it just expires when I press grab.

I have a trendy 12 hirose connector on it, with the trigger (4 pins) and GND (pin 1) connected to a TTL pulse generator (5V high low 0V; a relaxation area who worked with another camera).

Any ideas why this happens?  In addition, anyone know of documentation for the implementation of an external trigger with camera AVT?

Thank you!

Veritas

p.s. I also tested it with the example of NOR, triggered grab, but it also expires, or will be set on the trigger 'off' option when I start the program execution.

Without triggering, everything else seems to work very well.

PIN 7 (I/O ground) and PIN 4 (GPI1) for trigger connections. Tyr, you'll like it

See pages 54-55 in the Manual:

http://www.alliedvisiontec.com/fileadmin/content/PDF/products/All_Hardware_Installation_Guide/All_Ha...

-AK2DM

Tags: NI Hardware

Similar Questions

  • DALSA GigE or camera validation fails when no trigger external line is present

    Hi, I hope someone can help me with this problem of Dalsa GigE I get:

    When I have the camera set to trigger external line (LineTriggerMode = 1) and do not have the external clock running then it refuses to allow an Imaqdx configure 'Acquisition' ends without error "attribute value out of range (0xBFF69012).  However, if I have the external clock running (for example at 1 kHz), it's going OK.

    The same thing happens in MAX: I can not navigate to the camera, if the external clock signal is not present (otherwise MAX complains with Unable to Get attribute 0xBFF69011).  With the external clock running, everything is OK.

    So I used Camera Validation Utility or that comes with IMAQdx:

    Without the external clock signal, it reports an error:

    Attribute: CameraAttributes::AcquisitionAndTriggerControls:LineTrigger:ExternalLineTriggerFrequency

    This is the camera of SG - 11? If so I can tell you that there are a lot of questions using this camera with GigE Vision Software generic rather than own Dalsa SDK.

    That said, you could go into the XML file for your camera and comment the partular attribute that is not read correctly. XML files usually live here: C:\Users\Public\Documents\National Instruments\NI-IMAQdx\Data\XML (on Vista/Win7) and you would find the entry

    ExternalLineTriggerFrequency

    and comment it out as below (or remove the line)

    Eric

  • Good method to reset the tcp connection after timeout error

    I have an application that I build that communicates with a Modbus TCP device.  If a communication occurs error I wish I could reset it TCP communication.  What I have is a control that raises an event when pushed.  In this case, I have a sequence that closes first the tcp connection and then opens a new connection.  My application starts and works very well.  To test the reset function, I removed the ethernet cable from the camera and waited until a timeout occurs.  I plugged the cable reset back to and pushed my control. Sometimes the reset will take place, but most of the time I'll get a timeout in the TCP vi open error.  After that, the only way I can establish communications must leave my application, disable and then enable the network device.  Then, when I restart my application I have communication with my camera.

    Any help would be appreciated on how I should be reset my TCP connection.

    Thank you

    Terry

    Terry S of a. in writing:

    I've attached an example vi (LV10) that shows just the connection TCP and Reset.  An error occurs when you try to run the open in the event of reset tcp protocol.

    As writing that your code should be fine. There is nothing inherently wrong with it. However, depending on the device, you communicate with you can try to restore the connection too quickly once you have closed the connection. The device allows multiple connections to it and may require some time to clean up the things on his end after you close a connection. An experimental basis try wait little time between TCP and the TCP Open shut it down. If possible you can try using Wireshark to see what is happening on the network. It may be useful to diagnose what is happening.

  • How to move photos from a camera to an external hard drive?

    I did it before connecting each of them in my iMac, but I don't remember the correct sequence and the steps necessary to transfer the photos from my camera to my external hard drive. Thanks for your suggestions.

    The simplest method is to take the SD card out of the camera and then insert it into the SD slot on the side of your 2011 27 "iMac and copy and paste the pictures from the SD card to your DHM.

  • VISA read timeout error - Keithley 2400

    I am using LabView 2010 to control a Keithley 2400 Sourcemeter on an RS-232 Interface. I want to set up a measure and take a reading (e.g. ground voltage / time)

    I took an example of "Keithley ReadOnly" library code, but the 1073807346 error to retrieve box "initialize". Then I looked in 'Initialize. VI"and found there is a VISA (timeout error?) reading error. I have attached two screenshots that shows errors. Can someone tell me how to solve the problem? Moreover, I am very new to labview, if someone could suggest a solution that is not too 'Advanced '? Thank you very much.


  • VISA READ timeout error - several GPIB resources

    Hello

    I'm working on a network 3 GPIB instruments (Optical Attenuator, amplifier in fiber, spectrum analyser), controlled using VISA sessions in Labview. When it is run separately, the three corresponding screws (which are located in three different Labview projects) works as expected. However, when they ran at the same time, one gives them timeout-1073807339 VISA READ errors. These errors seem to occur when another instrument is sending / receiving data / instructions at the same time that she is.

    The exact context of the error is either:

    -an another VI is running, which includes sending several requests and responses every 100 ms, reading

    -by failing VI starts, I get an error of waiting time among the first Subvi containing a VISA READ operation to perform (sometimes initialize.vi (in situation 1), sometimes one of the subVIs connected the rest State (State 0) on the time-out of the structure of the event).

    or:

    -the default VI is running,

    -by starting another VI, which includes repeatedly sending requests and reading the responses, the failing VI up a mistake among the first Subvi containing a VISA READ operation to run (one of the subVIs linked the State of rest (0) on the time-out of the structure of the event).

    What I tried:

    -gradually increasing the delay between the VISA WRITE and READ operations to the relevant instrument (from 10 ms to 10 s), without success. More surprising are my observations which, by operating this single VI, increasing WRITE it / READ delay results in the same timeout errors. I have found no mention of such behavior through research google and forum. I hope that this may point to a solution to the main issue,

    -switching between synchronous and asynchronous VISA WRITE / READ operations.

    -reorganization of the network GPIB to a star to a linear topology topology (three instruments have different GPIB addresses in case anyone is wondering).

    My thoughts:

    It seems to me that the error is related to a delay introduced between a VISA request and its read operation by the transmission of another query associated another instrument in the same network GPIB. But I have no idea why pass a query to another instrument would introduce such a delay, or why this delay would result in a timeout error (and only an instrument, while writing / reading in each pilot screws are basically the same). Hopefully a more experienced Labview-er will be able to shed some light on my problem.

    Included is the project that contains the default VI (main.vi) and the driver custom made use of.

    There are a number of ways. If you want to keep separate projects for instruments, you can use semaphores often slandered around calls for screws in each project. Locking is not expected or predictable, but it would give controlled access to the GPIB resource.

  • semaphore timeout error 0 x 80070079

    Backups continue to fail.  I tried "autobackup" and it stops.  Used backup vista and has received 0 x 80070079 semaphore timeout error.  How can I remove or change this feature.

    Hello

    Method 1:

    Temporarily disable the antivirus on the computer running software and check if you are able to install the software.

    Disable the anti-virus software

    http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

    WARNING: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

    Method 2:

    I suggest you perform the clean boot and check.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

    See also:

    Error 0 x 80070079: the semaphore timeout period has expired

    http://social.technet.Microsoft.com/forums/en-us/itprovistanetworking/thread/c3fc9f5d-c073-4A9F-bb3d-b7bb8f893f78/

  • Backup has encountered a problem during backup of the C:\Windows\System32\config\systemprofile\Dropbox\Camera file will be mailed. Error: (System does not find the specified path. (0 x 80070003))

    This is the error message I get after several days of decline in dropbox, my Norton, saying that he was sure loading! I have read and re read most of what people have written, and I have no idea! I'm not a person irritable and can someone put in easy terms what should I do to solve this problem! I read try it who try and read that nothing works. Does anyone know if something works and can it tell me please. Also if someone from Microsoft is reading this why not have you solved this problem?

    Backup has encountered a problem during backup of the C:\Windows\System32\config\systemprofile\Dropbox\Camera file will be mailed. Error: (System does not find the specified path. (0 x 80070003))

    Hello

    You did changes to the computer before the show?

    These problems occur because the folders or libraries that you are trying to back up or restore include a reparse point. Analytical points are similar to shortcuts Windows or Unix symbolic links. A point of analysis can be used to point to a file that is moved temporarily to a different drive.

    Windows backup or restore 0 x 80070001, 0 x 81000037 or 0 x 80070003 errors
    http://support.Microsoft.com/kb/973455/en-us

    I hope this helps. Let us know if you have other problems with Windows in the future.

  • What is wrong with this sequence, it does not work when, after 3 inserts, I add a new record with the trigger it gives an error.

    Mr President.

    What is wrong with this sequence, it does not work when, after 3 inserts, I add a new record with the trigger it gives an error.

    --SL_CUSTOMERS table data
    
    
    INSERT INTO SL_CUSTOMERS VALUES(1,'Kamrul Hasan',NULL,NULL,'Moghbazar', 'Dhaka','0456789123',NULL,NULL,NULL,'Y',NULL);
    INSERT INTO SL_CUSTOMERS VALUES(2,'Rabiul Alam',NULL,NULL,'Motijheel', 'Dhaka','0567891234',NULL,NULL,NULL,'Y',NULL);
    INSERT INTO SL_CUSTOMERS VALUES(3,'Shahed Hasan',NULL,NULL,'2-G/1,2-2,Mirpur', 'Dhaka','0678912345',NULL,NULL,NULL,'Y',NULL);
    
    
    
    

    CREATE SEQUENCE  "ALIZA"."SL_CUSTOMERS_SEQ"  MINVALUE 1 MAXVALUE 9999999999999999999999999999 INCREMENT BY 1 START WITH 1 NOCACHE NOORDER  NOCYCLE ;
    
    
    CREATE OR REPLACE TRIGGER SL_CUSTOMERS_TRG 
    BEFORE INSERT ON "ALIZA"."SL_CUSTOMERS"   
    FOR EACH ROW   
    BEGIN   
    IF :NEW.CUSTOMER_ID IS NULL OR :NEW.CUSTOMER_ID < 0 THEN  
      SELECT SL_CUSTOMERS_SEQ.nextval   
        INTO :NEW.CUSTOMER_ID  
        FROM DUAL;   
      END IF;   
    END;   
    /
    
    
    
    

    When I try to insert several records with the seq.nextval it gives error

    violation of primary key.

    INSERT INTO "ALIZA"."SL_CUSTOMERS" (CUSTOMER_NAME) VALUES ('sdfsd')
    ORA-00001: unique constraint (ALIZA.SL_CUSTOMERS_PK) violated
    ORA-06512: at line 1
    
    
    
    
    One error saving changes to table "ALIZA"."SL_CUSTOMERS":
    Row 4: ORA-00001: unique constraint (ALIZA.SL_CUSTOMERS_PK) violated
    ORA-06512: at line 1
    
    
    
    
    
    
    
    

    Concerning

    Mr President.

    I find the solution by creating a function before the triiger

    as below

    CREATE SEQUENCE  "ALIZA"."SL_CUSTOMERS_SEQ"  MINVALUE 1 MAXVALUE 9999999999999999999999999999 INCREMENT BY 1 START WITH 1 NOCACHE NOORDER  NOCYCLE ;
    
    CREATE OR REPLACE FUNCTION get_SL_CUSTOMERS_vId RETURN VARCHAR2 AS
    BEGIN
       RETURN SL_CUSTOMERS_SEQ.NEXTVAL;
    
    END;
    /
    
    CREATE OR REPLACE TRIGGER SL_CUSTOMERS_TRG
    BEFORE INSERT ON "ALIZA"."SL_CUSTOMERS"
    FOR EACH ROW
    DECLARE
    dummy VARCHAR2(200);
    BEGIN
      dummy := get_SL_CUSTOMERS_vId();
      :NEW.CUSTOMER_ID := dummy;
    END;
    /  
    

    It works very well

    Thank you all for the suggestions.

    Concerning

  • Smart View Timeout errors... again.

    Hello

    I have a strange problem with users receiving the Smart View Timeout error.  In a connection planning, executing business rules, some users automatically receive a message "request timed" out with instructions to "extend the parameters of «ReceiveTimeout, KeepAliveTimeout and ServerInfoTimeout.»»

    I studied this problem online for a solution and has confirmed that the following Windows registry settings are at stake:

    HKEY_LOCAL_MACHINE/Software/Microsoft/Windows/CurrentVersion/InternetSettings

    KeepAliveTimeout 720000

    ReceiveTimeout 720000

    ServerInfoTimeout 720000

    Note that these settings are not present in:

    HKEY_CURRENT_USER/Software/Microsoft/Windows/CurrentVersion/InternetSettings

    720000 = 12 minutes.  However, users get this message to approx. 30 seconds in the rule.

    I have the same registry settings on my computer, running the same business through the same connection of planning rules, and yet I don't receive time-out errors.

    Am I missing a setting somewhere?  Time-out settings must be in HKEY_CURRENT_USER instead of HKEY_LOCAL_MACHINE?

    Tom

    Hi ToX,

    Yes. These parameters must be created in the registry "HKEY_CURRENT_USER". That fixed the problem for me when I fell on the same subject.

    HKEY_CURRENT_USER/Software/Microsoft/Windows/CurrentVersion/InternetSettings

    Thank you

    TT

  • Bridges, in starting to copy files from Adobe Camera RAW to jpeg or tif, error "the file cannot be created" - can all someone please advise? No Tech phone today?

    To all

    In Bridge, in starting to copy files from Adobe Camera RAW to jpeg or tif, error "the file cannot be created" - can all someone please advise? (No phone Tech Saturday?)

    Thanks for the quick responses today from anyone in the community,

    -Mark, Portland Oregon

    Please provide details: you are not trying to change the file type by changing just the extension, are you?  That won't work of course,

    Either you try to run some type of script?

    To change a file type, you have TO open the file in Photoshop and do save as.  That can be automated.

  • PXI-6254 trigger external start (error-200452)

    Hello

    I have a PXI-6254, I need to start with an external signal, so it is synced with another device, however, regardless of the source, I say to use as a trigger (a PFI, PXI_Trig or PXI_Star line), LabVIEW tells me "error-200452..." The specified property is not supported by the device or is not applicable to the task. "For example, I'm doing a digital output using the example of 'Write dig Chan - Int Clk - Dig Start.vi'.

    Is it really the case that this device cannot be triggered by an external signal? The manual for this device (http://www.ni.com/pdf/manuals/371291h.pdf) implies that it can be triggered externally, and if it is possible, what I am doing wrong?

    See you soon,.

    Simon Coop

    Hello Simon,.

    The error that you are running in as well as the solution is summarized by the following section in the M Series User Manual page 6-3.

    Kind regards

    Izzy O.

    Technical sales engineer

    National Instruments

    www.NI.com/support

  • Embedded the swf using the external video (FLVPlayback) error #2035 / #2044

    I struggled with this a lot recently, and I don't even know if it's at all possible.

    I am currently working on a project where I am incorporating a .swf inside another .swf.

    The built-in .swf file however also uses the external videos FLVPlayback to load component, this is where the problem starts.

    When you publish the .fla project I get the 2035 # IOErrorEvent when tracing the problem I get the #2044, it is to be expected however.

    The embedded swf is always looking for external videos, but since the new ROOT is the swf file, in which it is integrated, it will not find these videos.

    I need to know if there is a way I can specify or link these external videos required by the embedded swf file FLVPlayback component.

    I really can't be bothered again all the video content and their incorporation in the timeline.

    Thank you.

    The code inside the SWF will trigger these errors will occur if you don't have the source for sovereign wealth funds to stop it.

    If you do then you can just access SWF files loaded the mother/stub swf you have and check anything with a name or instance on the display list with the code, as all of the FLVPlayback components. You can then tell them the correct path.

    Otherwise, it would take something like a rewrite mod apache to redirect paths incorrect film to the correct path.

  • external hard drive error

    Gusy I have my external hard drive from toshiba, it seems that I can copy is no longer the files inside it on another computer or hard drive. its gives me this error ", you can always open or copy the files on the disk, but you cannot save the changes.

    At first it worked fine on my mac I formatted as MS-DOS (fat32) then. I used it for awhile and it was fine, then suddenly it began to appear this error. It tell me to save, but when I try to do, I can't copy it to another somewhre. can someone help me?

    Try to run the help Utility/First on the drive.

  • Qosmio PX30t-A-119 - external Microphone configuration error

    I have a NCR-PX30t-A-119 - 23 Qosmio PX30t-A-119 "screen touchscreen all-in-one PC Core i3 - 3120M 8 GB RAM 1 TB HARD drive"

    Whenever I try to configure my external mic, I get the message "The Windows Shell common DLL has stopped working" and the microphone does not work. Can someone help me solve this problem?

    Hi Howie

    Just to better understand can you please explain what you do exactly and what measures do you before this error occurs?

Maybe you are looking for