Can I use a variable in step of TS Message for field 'waiting time '?

Is it possible to use a variable (inhabitants, parameters, etc.) for the field "Wait time" in the stage of message TestStand?

TestStand 4.1

Thank you

Rafi

Go to the step settings > properties > Expressions > Expression Pre and enter something like:

Step.TimeToWait = Locals.MyTimeToWait

Tags: NI Software

Similar Questions

  • How can I use two counters to capture a pulse ttl for a specified time

    Configuration: Card counting 6062 PCI w / BNC 2121 Board running under LV 9.0 PerkinElmer Avanlance Photodiode (SPCM-AQRH-13)

    I searched through the forums and fell on the theme of framing an image while collecting signals from a source for a specified time.

    The example in terms of falkpl in 2005:

    "

    Dismal Hello,

    I'll try to point you in the right
    direction to start coding the application, but do not forget my
    suggestions have to be modified to your specific request.

    For
    the task output redeclenchables finished meter you need to
    your counter seconds in this application, I suggest to take a look
    in the Finder example in LabVIEW ('Help' are examples) and less
    DAQmx hardware entry & exit"" generating digital impulses.  Here,
    you will find some Gen dig Pulse - Retriggerable.vi.  You can use this for
    Create your door 4 pulses ms it's over (not a pulse train) and
    redeclenchables (for each time you go to the next step.

    In
    regards to the configuration of the first counter, there are several things to
    consider, and I can offer initial help to get set up.  You
    in-house allows to route internal CTR1 (4ms of pulse) output for your CTR0
    Door to measure only during the time.  Here are additional
    Info
    to do this in LabVIEW.  The source of your task of edges ABOVE County
    will be the TTL signal you are measuring and counting.  It comes
    on the PFI line that corresponds with CTR0 Source.

    When
    you make a measurement finished with CTR0, you will take only heads while
    the door is high and your source has a rising edge.  You can set the
    measure over to start on a trigger, which is not clear in this
    for example, that you have identified.  Since you know that you have a finished 4ms pulse
    time to measure, you can set the duration of your measure
    as a result.

    I found this
    Forum
    which may help some, but the coding is
    textual.   I hope this can give you a good starting point for
    programming.

  • Can I use a variable in a slider?

    Version of DB 10g
    Developer SQL 3.

    Hi once again, everything

    This post is a result of the post previous 'Sequence increment by 2 and not 1.'

    Here's a quick run down of what I do.
    We have historical records dating back decades and decades and decades (1900). Some of the most recent data were recorded in the worksheets. With some manipulation of data, it was possible to reorganize the data in its forms of entry in a flat file. These data were then imported into Access database, then using SQL Developer I made a data base for each access database connection and used copy for Oracle... tool to create a table in my flat file schema. In test data that I have right now that I copied the 5 access to Oracle databases and the results are five paintings called plot_84, plot_151 etc. I created a database that contains four main tables where the data from the flat files must be inserted, to standardize the it (I think the sentence is).

    I with the help of a large number has been able to train the following anonymous block, and it works very well (with the exception of the question of sequencing).

    DECLARE get_plot_measurement_id NUMBER;
    update_plot_measurements VARCHAR2(4000);
    get_tree_id NUMBER;
    get_plot_id NUMBER;
    
    BEGIN
        --1. Initiate insert process by getting PK from psp_plots
        SELECT plot_id INTO get_plot_id FROM psp_plots WHERE plot_name = 84; 
        
        --2. Insert records into psp_plot_measurements and keep relationship with psp_plots with variable get_plot_id.
        --   and get primary key value of psp_plot_measurements to insert into psp_tree_measurements during loop process.
        INSERT INTO psp_plot_measurements (plot_id) VALUES (get_plot_id) RETURNING plot_measurement_id INTO get_plot_measurement_id;    
        
        --3. Update record created at point 2.
        UPDATE psp_plot_measurements
           SET measurement_date    = (SELECT DISTINCT measurement_date FROM plot_84)
             , codominant_height   = (SELECT DISTINCT codominant_height FROM plot_84)
             , assessor            = (SELECT DISTINCT assessor FROM plot_84)
         WHERE plot_measurement_id = get_plot_measurement_id
         ; 
      
        --4. Open cursor to insert rows one at a  time and maintain relationships between related tables.
        FOR c1 IN
          (SELECT tree_number 
             FROM plot_84
          )
          
          LOOP      
        
            --5. Insert record into psp_trees
            --   and get primary key value of psp_trees to insert into psp_tree_measurements
            INSERT INTO psp_trees (plot_id, tree_name) VALUES (get_plot_id, c1.tree_number) RETURNING tree_id INTO get_tree_id;
        
            --6. Insert records into psp_tree_measurements and keep relationship with psp_trees with variable get_tree_id.
            INSERT INTO psp_tree_measurements (plot_measurement_id, tree_id) VALUES (get_plot_measurement_id, get_tree_id);
        
          END LOOP;
    
    END;
    /
    But me being someone who loves jobs mind numbing again and again, and more (about 1000 times x, who knows) still wants something I can preload a list of arrays of flat file (5 in this example) and just not run it.

    The problem is the following:
    Can I use a variable in a cursor, how are hilighted in bold below.

    "BOLD" has not worked is the bit of code FOR c1 IN (SELECT tree_number FROM plot_ | col_name_var) you will see just under point 4 below
    DECLARE p_column_num NUMBER;
    col_name_var VARCHAR2(30);
    type number_ptb IS table OF VARCHAR2(4000);
    p_column_nam number_ptb;    
    get_plot_measurement_id NUMBER;
    update_plot_measurements VARCHAR2(4000);
    get_tree_id NUMBER;
    get_plot_id NUMBER;
    
    BEGIN
    
        p_column_num := 5;
        p_column_nam := number_ptb();
        p_column_nam.extend(6);
    
        p_column_nam(1) := 84;
        p_column_nam(2) := 151;
        p_column_nam(3) := 152;      
        p_column_nam(4) := 214;
        p_column_nam(5) := 283;
    
        FOR loop_int IN 1 .. p_column_num
        LOOP
    
          col_name_var := p_column_nam(loop_int);
    
    --1. Initiate insert process by getting PK from psp_plots
          SELECT plot_id INTO get_plot_id FROM psp_plots WHERE plot_name = col_name_var; 
        
    --2. Insert records into psp_plot_measurements and keep relationship with psp_plots with variable get_plot_id.
    --   and get primary key value of psp_plot_measurements to insert into psp_tree_measurements during loop process.
          INSERT INTO psp_plot_measurements (plot_id) VALUES (get_plot_id) RETURNING plot_measurement_id INTO get_plot_measurement_id;    
        
    --3. Update record created at point 2.
          update_plot_measurements := '
          UPDATE psp_plot_measurements
             SET measurement_date    = (SELECT DISTINCT measurement_date FROM plot_' || col_name_var ||')
               , plot_size_10_30cm   = (SELECT DISTINCT plot_size_10_30cm FROM plot_' || col_name_var ||')
               , plot_size_30_50cm   = (SELECT DISTINCT plot_size_30_50cm FROM plot_' || col_name_var ||')
               , plot_size_50cm      = (SELECT DISTINCT plot_size_50cm FROM plot_' || col_name_var ||')
               , codominant_height   = (SELECT DISTINCT codominant_height FROM plot_' || col_name_var ||')
               , assessor            = (SELECT DISTINCT assessor FROM plot_' || col_name_var ||')
           WHERE plot_measurement_id = ' || get_plot_measurement_id
           ;
     
           EXECUTE IMMEDIATE update_plot_measurements;
      
    --4. Open cursor to insert rows one at a  time and maintain relationships between related tables.
          FOR c1 IN (SELECT tree_number FROM plot_|| col_name_var )   
              LOOP      
        
    --5. Insert record into psp_trees
    --   and get primary key value of psp_trees to insert into psp_tree_measurements
                INSERT INTO psp_trees (plot_id, tree_name) VALUES (get_plot_id, c1.tree_number) RETURNING tree_id INTO get_tree_id;
        
    --6. Insert records into psp_tree_measurements and keep relationship with psp_trees with variable get_tree_id.
                INSERT INTO psp_tree_measurements (plot_measurement_id, tree_id) VALUES (get_plot_measurement_id, get_tree_id);
        
              END LOOP;
      END LOOP;
      
    END;
    /
    Reviews on my welcome code.

    Ben

    Published by: benton on Sep 1, 2011 11:31

    Published by: benton on Sep 1, 2011 11:32

    Published by: benton on Sep 1, 2011 11:34

    with your current model, you need to write once for each table or write dynamic SQL regardless of the bulk of collect. adding most collect simply means you can do all the inserts in a single step and generally average performance benefits (see docco to COLLECT in BULK and for ALL).

    However, it is not really solve your problem.

    can I suggest an ETL step where you move all of the data in a table, then cross and run this function on all resulting?

  • WARNING: Incompatible Arg. You can't use stack Variables If generating series is not defined

    What does this message mean?

    "WARNING: incompatible Arg. you can't use stack Variables If generating series is undefined."

    Where can I put generate series only?

    Thank you

    Derek

    Hi Derek,.

    Not all LabVIEW C Generator settings are compatible with each other. In this case, you must define generate series only (aka 'disable parallel execution') If you want to generate the code uses the variable stack.

  • can we use repository variables in bi publisher as in answers

    can we use repository variables in bi publisher as in answers

    If possible, how

    Yes,

    but you should use Oracle BIEE as data source in order to use the variable in the repository

    you will need to follow the following syntax: valueof ("variable")

  • Can I use a variable of environment inside a *.sql file?

    Hello

    I want to create an external table.
    Then I use the command
    create or replace directory abc as "C:\folder"... within a sql file.

    Now, I want "C:\folder" way to be dynamic I use this path in many other places also inside the sql file. So I thought to create an environment variable and set this value. I tried using like %Path% but it gives error... where % PATH%=C:\folder.
    Can I use a variable of environment inside a *.sql file?
    But how to do it or is there another way.


    Thank you
    Olivier

    Published by: user11018268 on February 19, 2010 01:03

    You can use a variable substitution:

    SQL> accept basedir prompt "input the base dir:  "
    input the base dir:  c:\exp
    SQL> create or replace directory exp as '&basedir';
    old   1: create or replace directory exp as '&basedir'
    new   1: create or replace directory exp as 'c:\exp'
    
    Directory created.
    
    SQL> create or replace directory exp_data as '&basedir\data';
    old   1: create or replace directory exp_data as '&basedir\data'
    new   1: create or replace directory exp_data as 'c:\exp\data'
    
    Directory created.
    
    SQL> create or replace directory exp_log as '&basedir\log';
    old   1: create or replace directory exp_log as '&basedir\log'
    new   1: create or replace directory exp_log as 'c:\exp\log'
    
    Directory created.
    
    SQL> select DIRECTORY_NAME, DIRECTORY_PATH
      2  from dba_directories;
    
    DIRECTORY_NAME                 DIRECTORY_PATH
    ------------------------------ ------------------------------
    EXP_LOG                        c:\exp\log
    EXP                            c:\exp
    EXP_DATA                       c:\exp\data
    

    Max
    http://oracleitalia.WordPress.com

  • Can I use my MacBook Air as an external display for a MacMini via ports thunderbolt?

    Can I use my MacBook Air as an external display for a MacMini via ports thunderbolt?

    Advice appreciated!

    No, you can't.

  • How can I use internal clock case OR USB - 6259 BNC for the acquisition of digital data in my own big software?

    I want to integrate the ANSI C sample program ReadDigPort - ExtClk.c in my own big package.

    I want to use the internal clock of the BNC NI USB-6259 (.. 80 kHz 120 kHz).

    In the document:
    High speed M: Series Multifunction DAQ for USB - 16-bit, up to 1.25 MECH built-in BNC connectivity. / s,.
    is written:
    Or sample DI source clock: Any PFI, RTSI, HAVE sample or convert clock, AO, Ctr n out internal and many other signals sample clock
    The digital subsystem doesn't have its own dedicated internal synchronization engine. Therefore, a sample clock must be provided another subsystem on the device or from an external source.

    How can I use internal clock case OR USB - 6259 BNC for the acquisition of digital data in my own big software?
    With what other subsystem on the device can generate a source of the clock? How?

    It is possible to set a clock on an internal counter (for example ' Dev1/ctr0"):
    Creates channels to generate digital impulses that define the freq and dutyCycle and adds the channel of the task that you specify with taskHandle.
    DAQmxCreateCOPulseChanFreq (taskHandle, "Dev1/ctr0" units, clockName, idleState,
    initialDelay, freq, the duty cycle); works

    But it is not possible to drive this internal clock to a terminal (for example "/ PFI0/Dev1"):
    DAQmxErrChk (DAQmxCreateCOPulseChanFreq (taskHandle, "/ PFI0/Dev1", clockName, units, idleState, '))
    initialDelay, freq, the duty cycle); does not work: error DAQmx: measurements: type I/O of the physical channel does not match the type of I/O required for the virtual channel you create. Name of the physical channel: PFI0. Name of the virtual channel: clock

    The sample clock source can be derived from an external terminal (for example "/ PFI0/Dev1"):
    Sets the source of the sample clock, the sample clock rate and the number of samples to acquire or generate.
    DAQmxCfgSampClkTiming (taskHandle, "/ PFI0/Dev1", maximumExpectedSamplingRate, DAQmx_Val_Rising, ")
    DAQmx_Val_ContSamps, bufferSize); works. Acquire or generate samples until you stop the task

    But it is not possible to derive the internal counter of the clock (for example ' Dev1/ctr0"):
    DAQmxCfgSampClkTiming (taskHandle, "Dev1/ctr0", maximumExpectedSamplingRate, DAQmx_Val_Rising,
    DAQmx_Val_ContSamps, bufferSize); does not work. Error: Acquire or generate samples until you stop the task: make sure that the name of the terminal is valid for the specified device. See Measurement & Automation explore valid names of terminals. Property: Property of DAQmx_SampClk_Src: DAQmx_SampClk_ActiveEdgeSource device: Terminal Source Dev1: Dev1/ctr0

    Hi datafriend,

    using what it says is correct:

    Or sample DI source clock: Any PFI, RTSI, HAVE sample or convert clock, AO, Ctr n out internal and many other signals sample clock
    The digital subsystem doesn't have its own dedicated internal synchronization engine. Therefore, a sample clock must be provided another subsystem on the device or from an external source.

    This means that if you do not use an external signal as clock you can use the sample clock to HAVE it on board or at the output of the internal counter.

    There are also 2 ANSI C examples in this regard:

    http://zone.NI.com/DevZone/CDA/EPD/p/ID/4485

    http://zone.NI.com/DevZone/CDA/EPD/p/ID/4488

    So in both cases you have to use a fictitious task you need only for the generation of the internal clock (HAVE or CTR)

  • Can I use other databases such as Storage Service Bus for Windows Server 1.0 beta?

    I tried the Service Bus for Windows Server 1.0 beta, everything works fine, but I want to know:

    Can I use a custom database provider to store messages and settings?
    or the windows server team plans on providing this functionality?
    Thank you.

    Hi zhengwb,

    I would suggest to repost your question among our professional audience of COMPUTING in Windows Server TechNet forums:

    http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

    Thank you!

  • How many times can I use a variable binding in a query of the VO?

    Is it possible that I can use a variable binding in a query of VO just once?

    I test a query that keeps throwing the Houston-27122 error by pressing the application module tester. I tried to limit the problem to the simplest possible case, and it seems that the error is caused by the fact that I use the same variable bind two or more times.

    When the query looks like this:

    query1.png

    I have run, enter 'x' and it returns me the result.

    When I change to:

    query2.png

    I have run, enter the value

    param.png

    and immediately get the error

    error.png

    The same thing in sqlplus runs without problem:

    sqlplus.png

    My version of JDev is build JDEVADF_11.1.1.9.0_GENERIC_150314.0718.6673

    Please, advise.

    P. S. where can I find documentation queries are supported in your? In particular, I'm interested if I can use WITH the clause. There seems to be some confusion on this matter (see, for example, Oracle SQL WITH clause support - JDeveloper and ADF)

    Thank you.

    It depends on:

    Open your VO in JDev and go the the query page.

    In the lower part, there is a drop down 'link type', it is usually set to "JDBC-positional. In this case, you will need to provide the bind value for each occurrence of the variable binding separately.

    You could change that to "named" (don't remember the exact name). But beware, this will also affect all relatioships master retail to others your. I think that this is not a good idea to change the style of binding to a single VO.

    Good bye

    DPT

  • Can I use session variables in data model BI publisher SQL query?

    Hi Experts,

    We apply security at the level of the BI Publisher 11g data.

    In OBIEE we do so using session variables, so I wanted to just ask if we can use the same session variables in BI Publisher as well
    That is, we can include a where clause in the SQL for the sample data as

    Where ORG_ID = @{biServer.variables ['NQ_SESSION.]} {[INV_ORG']}

    I would like to know your opinion on this.

    PS: We implement security EBS r12 in BI Publisher.

    Thank you

    Read this-> OBIEE 11 g: error: "[nQSError: 23006] the session variable, NQ_SESSION.» LAN_INT, has no definition of value. "When you create a SQL query using the session NQ_SESSION variable. LAN_INT in BI Publisher [ID 1511676.1]

    Follow the ER - BUG: 13607750 -NEED TO be able TO SET up a SESSION IN OBIEE VARIABLE AND use it IN BI PUBLISHER

    HTH,
    SVS

  • Can I use a variable, all referring to a text field?

    Hello

    I have to settle for some fields readOnly property DYNAMICALLY (I mean, until the moment of execution, I do not know which fields are read-only and which are not?  .

    So I want to replace the TextField1 dynamically with all the fields in the syntax below. So, can we put a variable in the position of TextField1? If so, how can I do that?

    xfa.resolveNode ("VISITOR. Page3.SubFrom1.TextField1') .access = "readOnly";

    xfa.resolveNode ("VISITOR. Page3.SubFrom1. MyVariableComesHere') .access = 'readOnly ';

    How can I put the variable in the Red position?

    In details:

    I have 5 fields, then I want to readOnly, then I hv to write as below,

    xfa.resolveNode ("VISITOR. Page3.SubFrom1.TextField1') .access = "readOnly";

    xfa.resolveNode ("VISITOR. Page3.SubFrom1.TextField2') .access = "readOnly";

    xfa.resolveNode ("VISITOR. Page3.SubFrom1.TextField3') .access = "readOnly";

    xfa.resolveNode ("VISITOR. Page3.SubFrom1.TextField4') .access = "readOnly";

    xfa.resolveNode ("VISITOR. Page3.SubFrom1.TextField5') .access = "readOnly";

    In fact, my requirement is differnent (I know at run time only... Wht wht fields I hv to set readOnly and wht wht fields should allow very good for entry), for this reason I want to use a VARIABLE in the 'position' of TextField1, TextField2... as bleow

    $myvariable var

    $myvariable = TextField1

    Closure of the TABLE

    xfa.resolveNode ("VISITOR. Page3.SubFrom1. myVariable') .access = 'readOnly ';

    Pls. Let me know I can sue a variable like this? If so, what is the correct syntax (pls.  Suggest me a free code to SYNTAX error, bcz am very very beginner to this)

    Thank you

    Thank you

    You can use the following...

    $myvariable var

    $myvariable = TextField1

    xfa.resolveNode ("VISITOR. (Page3.SubFrom1.' + myVariable + "") .access = "readOnly";

    Thank you

    Srini

  • can I use on my itunes account balance to pay for in-app purchases

    I have a 15.00 dollar balance in the itunes store.  Can I use this to pay for in-app purchases?  If yes how can I do this?    Thank you!

    1. it depends on the purchase.

    2. which is done automatically when authorized.

    (141939)

  • I can't use the tab key to move to the next field or use the shift and tab to move to the previous field in the forms.

    After update to 7.0.1 I can't always use the tab key to move to the next field or use the shift and tab key to move to the previous field in forms. He has always worked in previous versions and it is essential for my type of work. Does anyone know of a setting to enable this? If this is not the case, can the developers of Firefox is working on this issue (please). I love Firefox but desperately need this feature to work properly. Thank you!

    No - because it works in Mode safe mode, this means an extension is probably to blame. See http://support.mozilla.com/en-US/kb/Troubleshooting+extensions+and+themes

  • I can't use my credit calls w / my account # [removed for privacy]

    I bought a credit for 12 months for use w / my macbook Pro and I can't use it.

    I can't find the key for the numbers and contacts, or

Maybe you are looking for

  • How can I save my credit?

    Hi I changed my iphone6 at 6s, backup, my phone, all of my credits on I cloud disappeared, I buy an another gift cards of $25, how can u make sure that for me? I want my credit back, u please make my credits?

  • Range the range must belong to the size of the buffer.

    Hello I'm pretty stumped on this problem. I have a chart with a picture of Chartcollections. The tables are filled in at the same time. Sometimes, quite randomly, I get this exception. In this case, I had three parcels posted: System.ArgumentOutOfRan

  • How can I tell my computer to decompress a disc with a zip file and not with IE?

    I have Vista and tried several things without success.

  • Recovery BIOS for PC-FU037ET #UUZ

    Hello. I am trying to retrieve the password of BIOS for a HP FU037ET #UUZ small business PC factor. It looks like there's a protection system Advanced BIOS, because the motherboard reset does not help. I even took the battery and pressed the reset bu

  • HELP: Call card photo editor error

    Can I call core image change with this code bb::system::InvokeRequest cardRequest; cardRequest.setTarget("sys.pictureeditor.cardeditor"); // cardRequest.setAction("bb.action.EDIT"); cardRequest.setUri(QUrl::fromLocalFile(fileName)); cardRequest.setFi