Can I wireless use a 430 EX II as a slave with the flash integrated the T3i EOS?

I have a Rebel EOS T3i.  According to its manual, pp 191 ff, I can launch a remote speedlite wireless from the camera.  I get an error message cannot find the speedlite even if I set up my 430 EX II speedlite according to its instructions manual, pp25 ff.  Thanks for your help

Yes - the 430EX II will function as a slave and the T3i (but not the T2i or earlier) can trigger remotely the speedlite.

It of a little complicated and can be confusing.

First... set the 430EX II in the correct mode.  Press and HOLD the 'Zoom' button for 2 seconds approximately.  This active a menu that allows you to put the flash is in a mode single-fash vs remote "slave".  Semicircular keys to switch to read 'slave '.  Press 'set' (in the middle of these buttons of a semicircle shape.)  I happen to have my 430EX II practical, but it must default to the slave 'A' channel '1 '.

Now for the camera.

On your camera menu, tab to the left (which we'll call 'Caméra Red #1' to distinguish it from other tabs) has 'Flash' control as the last option on this screen.  Either way for cameras with a built-in popup flash, the menu is marked 'Flash Control'.  For devices that do NOT have the built-in pop-up flash, this menu is called "Flash speedlite external control.

In this submenu (Flash control), make sure "Flash of fire" (the top option) is set to 'Enable' or 'CustWireless' - should NOT be set to 'disable' or nothing will work.

You will see a menu choice for "external Flash func. parameter' (and also 'External flash C.Fn setting'.)  IGNORE THESE!  This is for the hot flashes that are in the camera hotshoe and do NOT control the remote flashes wireless.  This is probably where you were getting confused.

Then go to "built-in flash func. the parameters' where, paradoxically, you get to control how your device communicates with your flash REMOTE (Yes, I know that this is not the most intuitive place to put it.)  It turns out that it is your INTERNAL flash that is responsible for communicating with any flash slave remote.  The optical wireless actually uses visible light (many people assume that it is a communication infrared - me is understood - at the end of the day, I learned that was incorrect and it's actually the visible light of the flash itself.)  He quickly sends communication to remote control by pulse codes to tell flash what to do remotely.  All this happens until the image is exposed and you'd swear the only blinked once eyes flash... but it turns out that it is actually very busy away from the impulse to connect).

In the "func flash built-in. menu of settings"there are a number of things that you must set.

If you set the flash mode built in 'EasyWireless' it will be gray on many other parameters... basically the camera automatically decides what he wants to do.  I think that the only definition not gray is the channel number (which must match the channel number on your flash.  Channel numbers helps you can draw on events where other photographers are also using wireless flash and have no conflicts where they are triggering your flashes and vice versa.

If you set the flash mode built in "CustWireless" it allows you to set other options.  CustWireless offers the most control.  In the end, it's probably mode you will use the most, once you get used to distance Speedlites.

In CustWireless, the menu option 'Wireless' Func mode. becomes available.  This option allows you to decide if you want (I take these out of use for simplicity to explain):

(a) speedlites both internal and external to the fire as a single group (icon external flash, a PLUS sign (+) and the camera icon)

(b) the Speedlite flashes inside and outside to the fire, but allowing you to control the power RATIO (icon external flash, a COLON symbol ( and the camera icon means "ratios" can be customized.))

(c) only external Speedlites (only the external flash icon is on this option - no icon on the device).

I want to mention something about this external option only because it confuses most people initially.  The device communicates with the slave through the on-camera flash.  The flash on the camera quickly pulses to send the instructions for flashes to distance.  This means that to use the slave flashes, the on-camera flash must be addressed (in jumps - upward position).  If you ask for external flash only (without camera) the flash on the camera flashed only instructions BEFORE the opening of the shutter of the camera to take the exhibition.  When I started to learn from external Speedlite flashes, I saw the light on-camera flash and thought that my settings were ignored.  Do not worry... When you archive your images, you will see that there is no light provided by the on-camera flash during exposure... all this flashing comes before the opening of the shutter.   Everything happens so fast that you'd swear all the flashes triggered only once... but in reality they are actually much of 'talk' before taking the picture, but this happens at an incredible speed.

And one last comment... because the camera communicates through Optics (visible light) flash to talk to remote controls, it is important from the bottom of the body of your 430EX II can 'see' the flash on the camera.  In small parts, that no matter where the lower part of the body showed up... you notice the impulses of the light of the on-camera flash.  But in large halls or outside the lower body of your 430EX II (where the receiver is located) will have any reflection of the walls, etc.  In this case, simply turn the lower part of the body of the 430EX II so that it faces the on-camera flash.  You can then rotate the head of the 430EX II at the point where you need.  The 430EX II will trigger even in daylight, as long as it can 'see' as the on-camera flash.

Here is a video that can help you: http://www.youtube.com/watch?v=pQIyPWGPp5A

Tags: Canon Camera

Similar Questions

  • can I use photoshop on a pc and a mac with the same license?

    can I use photoshop on a pc and a mac with the same license?

    Yes, just install the application of cc, https://creative.adobe.com/products/creative-cloud on each computer desktop and use it to install your programs cc.

  • We want to use WinRM to our company to increase efficiency with the written scripts b admins.

    Hello

    We want to use WinRM to our company to increase efficiency with the written scripts b admins.

    But to avoid savage execution of multiple scripts, our security departments require 2 requirements:

    The fitting should be accepted only one server and only when encrypted (so be need a filter on the customers for this)

    And each running script must be connected

    So far I could not find a method to get this time. So, is there a way to do this?

    Best regards

    Original title: WinRM security

    This issue is beyond the scope of this site and must be placed on Technet or MSDN

    http://social.technet.Microsoft.com/forums/en-us/home

    http://social.msdn.Microsoft.com/forums/en-us/home

  • I can't find Fireworks on creative cloud. Fireworks is included with the subscription?

    I can't find Fireworks on creative cloud. Fireworks is included with the subscription?

    I need to download Fireworks and install it on my desktop, but is not in the app Manager?

    Hi Nigel,

    Yes the Fireworks is included in your creative cloud,

    You need to open the Office of creative cloud App go to the select Apps - filters and version - previous version selection Fireworks

    I have attached the screenshot

    Let us know if it works

    Kind regards

    Aurélie hamadi

  • I usually use my account from Microsoft to connect, but with the new update that I can not connect with her

    After the new update on the login screen it asks a Skype name and password. I used to use my microsoft account to connect to Skype and therefor have no idea how to connect with this new interface. I tried every password I can think and even changed my password on behalf of microsoft and still can't connect.

    Have you tried the login with the Microsoft account option.

    https://support.Skype.com/en/FAQ/FA12081/how-do-i-sign-in-to-Skype-for-Windows-desktop-with-my-micro...

  • Why can I not use office (trial expired) even if I paid for the subscription?

    I just bought the subscription student and teacher a year ago 10 minutes, and when I open Photoshop and Flash it does not detect that I've already paid for the subscription (trial has already expired). Any help would be appreciated, I'm sorry if this has already been posted. I have not received an email confirming my purchase and I signed as long as the same ID adobe like when I paid for the subscription.

    Hello

    I can't pull the top and recent details of the order with the email address used to log in to the forums. Could you help me with the order number, I can check in the system for you.

    ^ Ani

  • Why can't I use my serial number photoshop cs5.5 extended with cs6?

    It provides in the terms and conditions, on-screen instructions, a photoshop cs5.5 license can be used to apply to the photoshop cs6 version, but it shows as not valid.

    Y at - it a link to photoshop cs5.5 extended if it is incorrect?

    Kind regards.

    Scott Williams Evin

    P. S. My computer is a standard industry individually self-made with more than 3 terabytes of HARD disk space and 16 GB of RAM with 2 x 4600 Nvidia Quadro graphics for design work specific cards and running windows 7 Professional and an evaluation copy of windows 8, so I don't have a system of traffic on the specifications indicated the installation was fast, but I'm stuck with the invalid number serial number.

    Thank you.

    Post edited by: cypher 2d

    In this case I'd

    1) contact your Academy and see if they have updated their online courses to allow download of the CS6 extended to the time your semester begins and

    (2) contact the Customer Service of Adobe Education Store to see if you have met the requirements for obtaining the license CS5.5 after a certain date in the past, but before the release of the CS6.  You see that it is a certain window you must fall into. If you obtained the license too far in the past so it is not valid for the CS6 but your school should do rentals for you if they expect you to complete the course work.

  • I can't see a message from my Union because of problems with the address changed for pop-upwindows and some other issues

    Hello
    I am from Sweden and I have problems with a Web site that has my Union. I could see messages from them before, but they changed their address and on the site, they say people that they must put the new address on the approved list of the pop-up windows. I did but it still does not. Maybe I did wrong, I don't know, but it's annoying as hell that I can't see the messages they send.

    I really need help with that.

    Best regards
    Lena

    You can control and manage permissions for all areas on the Subject: authorizations page.

    You can delete all data stored in Firefox with a specific area through "Forget this Site" from the context menu of the history entry (see the history or the history sidebar) or via the subject: permissions page.

    Using "Forget this Site" will delete all data stored in Firefox in this area as bookmarks, cookies, words of past, cache, history, and exceptions, so be careful and if you have a password or other data from this area you don't want to lose so take note of these passwords and bookmarks.
    You can't recover from which "forget" unless you have a backup of the affected files.

    It has no lasting effect, so if come back you on such a 'forgotten' site, then the data of this Web site will be saved once more.

  • can copy CDs on computer but when I try to sync with the 4HDS mp error, clear DRM HDS APPEARS AND WON'T PLAY

    Can copy CDs on computer and on mp4 then error clear DRM HDS HDS appear and will not play

    Hello

    1 did you change on your computer?

    2. What is the exact error message you received?

    3. What is the model number of the device you are trying to synchronize?

    4. what application you are using Sync?

    I suggest you to follow the links and check out them.

    The Player Windows Media DRM: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows7/Windows-Media-Player-DRM-frequently-asked-questions

    Windows Media Player sync: Frequently asked questions http://windows.microsoft.com/en-US/windows7/Windows-Media-Player-sync-frequently-asked-questions

  • How can I find that a windows 7 install disc to go with the key on my laptop?

    Hello. For various reasons I had to format and reinstall windows on my lenovo think mobile W520. I have his activation code, but I don't have any sort of recovery disk. I have a 7 HP windows retail disc that I used for my office, but installation that will not let me activate with the key to the laptop. And naturally the key that came with the drive is in use. How can I find an installation disc that works with the key provided with the laptop? (AFAIK, lenovo site software all assume you have something to recover; in my case, the drive is formatted, and as far as I know, there is nothing to use to retrieve).

    No doubt you had failed to create the Lenovo recovery disks according to the instructions of Lenovo, and the hidden restore partition no longer exists?

    Download you the ISO that matches what you had, ISO, burning software to create the dvd. You must install the drivers for Lenovo support, and of course you will have none of the pre-installed Lenovo utilities

  • How can I recover file in table form in a modal window with the id of the request.

    Dear all,

    I use Apex 4.2 worm.

    I've created classic report with 5 columns and add additional column with the name "ADD COMPONENT" link in classic report.

    I call in a table in a modal window, click on link add COMPONENT classic report. .

    Modal window is popup when I click on the link add COMPONENTS , but it does not have any record of respective "Reservation_id and Res_line_id" I have place in link add COMPONENT report Classic.

    How can I view respective folder of reservation_id and res_line_id in table form in the modal window.

    I create in my account. You can view using

    Workspace: APEX_ISSUE

    User:               [email protected]

    Password: kaushik1@34


    Application 71690 - questions

    Page not 13

    Tab: In the form of modal window.

    Thank you

    Hi Maxence,

    CORINE wrote:

    It is wounderfull but I use the Apex 4.2 worm. There is no dialogue option and page mode.

    So how can I do that in Apex 4.2 worm.

    Check this old similar thread that runs in 4.2 APEX where I explained step by step: How to extract the values inside the jquery element dialogue modal rigion

    Also check the options of the iframe for your application sholud be set to 'Allow' or ' Allow from same origin.

    Edit Application Properties-> security-> the browser-> Embed security Connectionwithsuchprocedures-> is set to 'Allow' or 'Allow same origin'

    Hope this helps you,

    Kind regards

    Jitendra

  • How can I return to a version of Firefox that is compatible with the Norton Toolbar?

    After that I have updated to the latest version of Firefox, the Norton toolbar is disabled. I would go back to a previous version that is compatible with the Norton toolbar. Can I do this?

    For security reasons, it is preferable not to decline to 40 Firefox. I could refer you to this thread for a more in-depth review and suggestions: screwed up why Firefox NEW Norton Internet Security?

  • Can I update my Firefox if I have problems of redirect with the current version?

    Normally I would wait until things have been fixed, but not having any luck finding is not a solution and a number of sites are grumbling to me to still use the old version.

    Well, for my part, got tired of waiting for an answer and did the only thing I knew to do.
    First of all, I did a thorough scan of all drives with the latest definitions of virus/parasite and knew things were clean this way before you uninstall and re-make Firefox from scratch.
    Then I saved my favorites to .html and did an uninstall complete the old Firefox and didn't use the option to save my old settings, etc. (encrypted I would rather Redo from scratch that the chances of saving a part of my problem now.) After I had uninstalled, deleted the Firefox subdirectory in C:/Program Files and made a boot cold I advanced and installed a new version of Firefox, did the settings for my taste and import my favorites.
    All looks good after a number of cold and hot, boots so guess I cured the problem. I suggest you do this too and do not recommend that do you a simple update that may well leave the intact redirection problem. No evidence of this, but not worth the possibility for me. Good luck to all of you who take this route!

  • Install RDCman 2.2 the use Remote Desktop on windows server 2003 fails with the error: incompatible version of c:\windows\system32\mstscax.dll

    2.2 RDCman install remote desktop on windows 2003 server util fails with the error: incompatible version of c:\windows\system32\mstscax.dll

    CAN ANYONE HELP?

    Hi Mordi26:

    This could be because windows server 2003 is not updated with the latest version of the Terminal Server client. With terminal services client 6.0 update... It should solve the problem. Here is the link to download:

    http://www.Microsoft.com/downloads/en/confirmation.aspx?familyId=cc148041-577f-4201-B62C-d71adc98adb1&displaylang=en

  • Can ANY product Adobe CC ingest or import AVCHD (.mts) files with the metadata accompanying .xmp sidecar files?

    I had no luck with the sidecar xmp files relative in any product, including the prelude, Premiere Pro, Lightroom or bridge.

    Hi Mike,.

    Okay, I found the outline of the bug. I was initially on the assumption that the question was how the XMP was written by Daminion. This is not the case. Their XMP seems fine. The bug is with the way we are going to analyze these JVC AVCHD files. It will take some research more sort everything, but at least now I'm on the right track. I tested the creation of metadata for a variety of other files AVCHD from Canon and Sony. All these files caused first create the XMP files with the name xxx.xmp. But, when I added the metadata in the JVC, the xmp always emerged as xxx.mts.xmp file. Then... I did some more tests with the file. If the extension of the file to rename. MPG, suddenly all the XMP you added the file in Daminion appeared. All the new metadata that I created has also been added to this file.

    It seems that there is a specific bug in our file for this JVC AVCHD flavor Analyzer. I'll get this connected and see if I can get it fixed. In the meantime, you can rename the file extension. MPG, if you want to read your existing metadata. Or... you can add to the file xxx.mts.xmp.

    Insect. Thanks for the help to identify him.

    ~ Mitch

Maybe you are looking for