Can not see the 2nd partition on the computer after using the shrink volume option
I had 2 partitions on the hard disk the same... but after separate 60 GB unallocated space of 2nd partition (drive D) and after rebooting I don't see my 2nd partition. After that I tried to change the drive letter and path, but it displays the following message 'the operation did not complete because the disk management console view is not updated. Refresh the view by using the refresh task. "If the problem persists close the disk management console, then restart disk or restart the calculation Managerr. I don't want to lose the data.
Hello
· Have you installed a third-party program like Partition magic on the computer?
Try these methods further and check if it helps:
Method 1:
Try to use diskpart to assign a drive letter to the disk #0 Partition #1.
(a) click Start Orb > type diskpart
(b) click right diskpart in the above results > click run as administrator right
(c) once diskpart load type list volume, press enter
You should notice that you can see your partition you use for your data, it should not not have a drive letter assigned to it.
(d) type select volume 6 (replace 6 with the number of the volume assigned to the partition in question)
(e) type assign letter Z (replace Z with the letter you want to assign)
When you look in the computer, you should be able to see your score.
Method 2:
I also suggest that you run the Microsoft fixit tool and check if that helps:
Hardware devices do not work or are not detected in Windows
http://support.Microsoft.com/mats/hardware_device_problems/en-us
Method 3:
You can follow the steps in troubleshooting section below and check if it helps:
http://support.Microsoft.com/kb/2001877
Tags: Windows
Similar Questions
-
I'm trying to set up an ad-hoc connection between two laptops. I created a network. When I right click and select Properties. On the sharing tab, there is a check box for "allow other users to connect to this network. Below that, there is a drop down menu to "connecting home network." My problem is that I can't "wireless connection" under this sow drop andhence cannot establish a connection. Help, please! Using windows 7 64 bit home premium and have ralink 5390 adapter. I have internet through a wireless internet service provider. I use "Reliance Netconnect + wireless internet".
Hi Amit,
Please refer to this link and check if this helps you,
Set up a computer-to-computer (ad hoc) network:
http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-network
-
in Firefox can not see the downloads window, specialist of the jump in the trunk to see - the download speed
Downloaded a lot and now can not see how to fix it?The download Panel has been moved to the upper right corner with a circle arrow down. You can also visit on: downloads of your browser to visit all your downloads.
-
Can not see the images of the patent (that is, D/359 691) on USPTO.gov patent search, it tells me I need a plugin (Quicktime) that I've already updated.
In the 'quick search' I give terms & it compiles a list. I have then cross to every doc and look to see the doc and associated drawings. I don't know what to say at this stage.Thank you.
QuickTime cannot handle images in TIFF format.
You can watch AlternaTIFF - http://www.alternatiff.com/
-
Hi I can not see the App health or my pulse in the looks on my watch even if she is selected to appear on eyes on my phone?
Hello
Slide your finger left or right on the screen.
Also go to ibooks on the user guide iphone download Apple Watch is free.
See you soon
Brian
-
Import photos no problem can not see the photos on iPhone
I upgraded my MacBook Pro to El Capitan. Since moving from iPhoto to Photos (even before I updated the operating system) when I plug my iPhone 5 to import pictures in the selected library I do not see the photos appear in the import window so that I can select for imports. I literally had to email it to myself, and then import it into the e-mail. I work with different libraries within pictures, so I excluded it only love the library system. Same result, can not see the photos. Also, I have unplugged and replugged in and tried the other USB port to rule out hardware, while the Photos could force them to see the device as new, and that does not work either. I tried something another user who had to open Image Capture to see if she could see all the pictures on my phone and it doesn't work, I found (theory was that opening would make Photos recognize as well). However the Image Capture wouldn't add a USB scanner so I think it's not worthy of trust. Photos only setting I have enabled is the automatic update to iCloud. Otherwise, I don't know what another parameter to seek that could block it.
When the phone is connected USB the phone reboot - many have found this will clear this problem
LN
-
can not see the BTH003 on my Qosmio laptop bluetooth headset
can not see the BTH003 on my Qosmio laptop bluetooth headset
Hi koko,.
Welcome to the Microsoft Community Forums.
According to the description, it seems that you are facing problems that Bluetooth headphones are not detected. I'll be happy to help you with this problem.
(1) what is the exact error message / complete you receive?
(2) what operating system is installed on your computer?
(3) what is the brand and model of the Bluetooth headset?
(4) have you made changes on the computer before this problem?
I suggest you to follow the steps from the links and check if it helps.
Add a Bluetooth device to your computer
http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-enabled-device-to-your-computer
Change settings for a Bluetooth compatible device
http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-a-Bluetooth-enabled-device
I hope it helps. If you have any questions about Windows in the future, please let us know. We will be happy to help you.
-
WRT1200ac and WRT1900ac OPENVPN can connect but can not see the network
I can connect but can not see the computers on the network. I've tried everything. Any help would be great. Thank you
Firewalls are disabled on remote computers?
-
Microsoft Visual C ++ Runtime Error - can not see the path of the file.
When I get the runtime at startup error, I don't see the destination of the file. It is very annoying that I can not see the program that gives me the problem.
All it says, this is:
Runtime error!
Program: C:\Program F...
How can I extend the above so I can see the path of the actual file?
Also going to go for a 2 for 1 here...
Immediately after the closure of the runtime error box, I get the message that search settings stopped working. I close who and everything is fine until I reboot (by making the error happen) but I'd rather not have the problem in the first place. I run Windows 7 Ultimate.
Error information:
Signature of the problem:
Problem event name: APPCRASH
Application name: SearchSettings.exe
Application version: 4.5.0.2
Application timestamp: 4e04ab86
Fault Module name: MSVCR90.dll
Fault Module Version: 9.0.30729.4940
Timestamp of Module error: 4ca2ef57
Exception code: 40000015
Exception offset: 0005beae
OS version: 6.1.7601.2.1.0.256.1
Locale ID: 1033
Information additional 1:9956
More information 2: 995611374799875ff43c42d4b1b84d70
3 more information: 3d4b
Additional information 4: 3d4b4db0455ea2295d172b959897673cMaybe just download a new MSVCR90.dll but I would like to hear what you have to say.
Hello
· Did you the latest changes on the computer?
We must first identify to identify the program that is causing startup problems.
Step 1:
Check if the problem persists in safe mode.
Start your computer in safe mode
http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode
Restart the computer to return to normal mode.
If the problem does not persist in safe mode, then it is possible that some third-party programs installed on the computer is causing the problem.
Step 2:
I suggest that you put the computer in a clean boot state and check.
To help resolve the error and other messages, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.
See section to learn more about how to clean boot.
How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
http://support.Microsoft.com/kb/929135
Reset the computer to start as usual
When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
(a) click Start, type msconfig in the search box and press ENTER.
(b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.
(c) under the general tab, click the Normal startup option, and then click OK.
(d) when you are prompted to restart the computer, click on restart.
-
BlackBerry smartphones can not see the maps on my "BOLD"?
Hello
I just theBold on Orange in the United Kingdom and I do not see the maps app anywhere. I can see it listed as version 4.6.0 under the list of Applications but can not see the software somewhere?
I'm mean't to enable it somehow? Also can not get the GPS function works as it says "failed to update GPS location" when I click on refresh?
Any help would be really welcome
If your provider blocks the passage of the icon (like AT & T) to another theme (Options-> themes) and see if you can find it. You may also download. Check mobile.blackberry.com from your BB browser.
-
I get an error message of complete storage - please backup and remove your something online (can not see the full error message) when converting PDF reader to point rower inacrobat DC. Help, please
Hi debg25514049,
You will not be able to export your PDF to PPT using the service Adobe export in PDF format.
You'll need subscription to pack Adobe PDF or the Acrobat application to convert PDF to PPT.
Kind regards
Nicos -
When you try to crop an image in Lightroom develop I get a blue screen of overlay and can not see the image. I uninstalled and reinstalled but same result. How can I get this reset to display the selected image and handles of the crop?
Go to your Lightroom preferences, the performance tab and uncheck the box "use GPU processor."
-
Can not see the Spot Healing Brush Touch tab. Shows only the tab for the corrector.
Can not see the Spot Healing Brush Touch tab. Shows only the tab for the corrector.
Try right-clicking on the Healing Brush tool in the bar of the tool or SHIFT + J to switch tools...
-
Hi, just sign for cloud of plan monthly photoshop, has received a message from the Bank that I already paid with my credit card for the first month, but I received no email / can not see the plan when I open a session.
There is no serial numbers for products Creative cloud,
Sign out of Creative Cloud App and sign in the back once
http://helpx.Adobe.com/creative-cloud/KB/sign-in-out-creative-cloud-desktop-app.html
If the trial warning still appears, then make sure your hosts file once entries
Log, activation, or connection errors. CS5.5 and later versions
-
Can not see the whole clips on DVD
Hello
I recently created a project and it was engraved on a DVD. I can view the DVD very well, but can not see the entire width of the clips. I can see the entire width of the clips during playback on computer and TV. Any help is greatly appreciated.
Is the DVD 4:3 or 16:9 wide screen? What type of display you're displaying on - an old 4:3 CRT or a screen flat 16:9? What image is missing? Some televisions show a picture of overscan, part of the meaning of the image is lost under the bezel, unlike most computer monitors showing each pixel on the screen.
Thank you
Jeff
Maybe you are looking for
-
How can I fix secure connection failed trying to connect to my network attached printer?
When I try to connect to the web server integrated into my network attached to https:\\192.168.0.3 printer, I get the following error: | The secure connection failed|| An error occurred during a connection to 192.168.0.3.|| You have received an inval
-
Gigaframe L81 is OFF after 2-3 sec
Hello! In my view, there is a bug in Gigaframe L81 sw... I put the automatic light (auto light) options, then the LCD is turned off. Whenever I turn it on the screen shows but turns off immediately. I got tired of resetting, but she has - at least, i
-
Error code install Build-12 when copying distribution
Hello to you all, useful forum fans! I have problems of construction of a Setup program for my product now that I upgraded to LabVIEW 8.5.1 2010. My project is an executable version, and then 3 built installer who put a different value in the regist
-
For hp dv7 fingerprint reader works does not after updating to windows 8 pro
I have improved my dv7 with windows 8 preview version and finger print reader perfectally well worked and when I have upegraded to pro it has stopped working. When I upgraded I lost a bunch of programs so can someone help because I loved using my fin
-
Programs of client server that connects to the computer from a phone and store data on the PC as the synchronization programs have what user ID and are able to write to the disk by security group file permissions. Users authenticated Internet Explore