Can't do two screens to work - T510 mini dock (433710U)

Hello

I have two external monitors that I want to use at the same time. I have a Mini Dock (433710U) which has a VGA, DVI, and a DisplayPort. I connected 1 monitor to the VGA port and it was connected via DVI. When I used the dock, I get only the one plugged into the VGA port to display.

Can anyone here help?

Thank you!

You can change the direction of the screen extended using the display property, all you have to do is drag the screen to the location that suits you.

In addition, if you want to use all three LCD at the same time, we of the vga screen may need be run on the laptop itself, rather than via the vga of the station entrance.

Tags: ThinkPad Notebooks

Similar Questions

  • How can we operate two screen on vista - do not reproduce but to run applications separated on each screen-AT

    How can we operate two screen on vista - do not reproduce but to run applications separated on each screen-AT

    Choose the option 'Extended' instead of 'mirrored '.

    http://Windows.Microsoft.com/en-us/Windows-Vista/multiple-monitors-frequently-asked-questions

  • How can I run two screens side by side in Windows 7 Ultimate?

    I use Windows 7 Ultimate, 32-bit version on a Dell desktop computer.  I have two LCD screens showing identical pictures.  What I want to do is to have the two screens as one, so that I can drag a document or an image on a screen while watching another image or another document on the original screen.  I'm used to be able to do this until I had to format my C: drive to get rid of a malfunction.  I have reloaded my Windows 7 Ultimate but forgot or cannot display restore both. A single screen appears when I look at the display section in the Panel. Any help to get back to my two original screen function would be very welcome.
    banned

    1 DVI, the second connector is VGA or also known as the D - Sub. A monitor itself requires no software to run.

    What connectors you join takes him to the computer? Connectors in the same group as the USB, audio jacks and network are referred to as being on board, connectors in parallel slits separated from these ports will be a graphics card. In this photo embedded graphics connector would be where is the serial port.

    Not all motherboards will allow you to use both the on board graphics card ports at the same time and. Installation of the card automatically turns off the edge card.

    In this example, the graphics card has two types of port (analog video port = VGA) and in this case the two ports can be used.

    Some graphics cards have only DVI ports, but most will support VGA with the use of an adapter DVI / VGA

  • New X 220 supported two external monitors with the mini dock plus?

    Hello

    I need to buy a new laptop of Lenovo in emergency.

    But we must ensure that it supports dual display on two external monitors. (VGA)

    My question is:

    (1) we plan to buy with the mini dock more, she has two HDMI port.

    can it support two external monitors for Intel HD Graphics 3000?

    (we will close the covers when to use two external monitors)

    (2) can I use DVI to convert converter VGA to VGA to support two external monitors

    (3) what is the difference in weight to 220 X SATA HDD and SSD HDD?

    Please help to emergency!

    Rgds,
    Sun

    Hello

    Yes, it works.

    He must need a converter VGA (F) display port.

    Thank you.

    See you soon
    Sun

  • How can I connect two screens for MacBook Air (mid-2012)

    I have a macbook air (mid-2012) which, according to apple, can support two external displays.  I have an external display connected to the thunderbolt port, but may not know how to connect to the other?  The mac has only a thunderbolt port?  It has two usb ports.  Is there a thunderbolt display port separator that works with this Apple?  When I look on amazon I see some who make the separation, but they say that they do not work with the Mac?  Any recommendations would be greatly appreciated.  Thank you in advance!

    You can daisy chain a thunderbolt cable from the first screen to a second screen to support both with port of a sudden lightning. Reported here.

  • How can I connect two screens for MacBook Air?

    I have a macbook air (mid-2012) which, according to apple, can support two external displays.  I have an external display connected to the thunderbolt port, but may not know how to connect to the other?  The mac has only a thunderbolt port?  It has two usb ports.  Is there a thunderbolt display port separator that works with this Apple?  When I look on amazon I see some who make the separation, but they say that they do not work with the Mac?  Any recommendations would be greatly appreciated.  Thank you in advance!

    I accidentally listed the issue as resolved, but it is not.  Thank you for all the advice!

    Hello..

    You need a hub of Thunderbolt.

    Try Amazon.

  • Satellite Pro P100 can not get the screen to work again

    If someone could point me in the right direction, I would be very grateful!

    I bought a monitor to use when I am in the office (it's a LG Flatron L225WT), installed the software that came with it and plugged. Nothing seemed to happen, then in Toshiba HWSetup, I changed my power on the screen 'LCD + Analog RGB'.

    To cut a long story short, the external screen works perfectly now, but I cannot access the internal screen, even after changing the power supply on the display to 'Automatic Selection '. The Fn + F5 key does not appear to have any effect at all.

    I must have inadvertently done something to mess up the computer. Can anyone suggest how I could reset it back?

    TIA to all who can help you!

    -Laurence

    I put t know what laptop you have and don t know what OS you are using, but it seems that you have managed to set the external monitor as the main screen.
    You should change in display properties (right click on desktop-> properties)

    Somewhere in the settings, you should try to score the internal display (1) and should mark use this device as the primary monitor

    You won't find any similar settings or this will not help then set the operating system to the point of time at the beginning. In this case all settings will be reset!

  • I can't get two cards USB worked at the same time

    I use Labivew 8.6 to program an application using NI UBB-9211 and USB-6211 connection to two USB ports on my PC in order to measure the temperature and pressure (voltage) at the same time. Also, I need to generate two AOs of USB-6211 to drive my engines. I tested two cards, they are OK. But when I program them together, I get only 9211 worked, an error poped to acquisition of data USB-6211. Could you please help me on this? advice or examples of VI / would be greatly appreciated. Thank you in advance!

    Hi navistar.

    It seems that you should be able to do what you are trying to accomplish. Can you post some information about the error you receive? You use the lower level Assistant DAQ or DAQmx screws in your application? You can post a screenshot of your code where it is merged together and easier troubleshooting. You use any trigger of your application? We have examples in the example Finder (help > find examples) under Hardware Input and Output > DAQmx. These examples are a good place to start to build your application. If you already have the code work for each instrument and you have problems combining them, it might be easier to work with where you are at as opposed to leaving it everywhere.

  • I can't get two games to work on Vista.

    I can get the games loaded on the computer, but when I go to play it the screen comes up for a second then it turns off.  'Notification of optimal resolution' see a screen I clicked and who and disabled, it did not work so I allow it and it still does not work.  Both games are the treasures lost Alexandria and Big Kahuna Reef.

    Notification of optimal resolution generally tells you that you need to change your resolution to something else to play the game.  For example, if the game is designed for 1076 x 768 resolution, and your use of your computer in 800 x 600, the game may not work.  In general, he says that you must be in the resolution, and then you can adjust your resolution to suit.

    You can change your resolution by clicking on START-> control PANEL-> PERSONALIZATION

    Then click on display settings

    You will then see a slider, which will allow you to increase or decrease your resolution.  When you find the optimum resolution that is requested by the game, select it, and then try to restart your game.

    Let me know if you have any other problems or if it works for you.

  • Satellite P100: Can I connect two external monitor to the VGA & DVI port at the same time?

    Satellite P100 comes with two port external monitor. One VGA and one DVI. Can you have two external monitor works at the same time? Can you have two external monitor as well as your internal screen working at the same time (for a total of 3 screen at the same time?

    Here's what I confirm:

    Internal display + display DVI connector
    OR
    Internal display + screen VGA connector

    Is it possible to have:

    Display connector DVI + VGA connector display?

    OR

    Display connector DVI + VGA connector screen + internal display?

    As far as I know, this is not possible and you can use a DVI or VGA port.
    Output signal can be used only a single port for external monitor.

  • After a clean install of Windows 8, I can't get three monitors to work

    I did a clean install of Windows 8 pro.  I have a Dell T1500 with over-pants V4800 graphics.  This machine previously had Windows 7 installed and works with the ATI driver.  With Windows 7, the three monitors worked without problem.  Now, with Windows 8 installed I can't get two monitors to work.  I use the more updated driver for Windows 8 for the map on the website of AMD.  The third monitor can be seen on the page of the screen resolution, but I cannot "extend desktop...". "the third arch.  When I try to do so it gives me a message saying

    "The display settings could not be saved.  Please try another combination of display settings. »

    All three monitors are the same, Dell P2210.  I tried different resolutions. I tried the driver I was using on Windows 7, I uninstalled the driver and adapter repeatedly.  I installed all the drivers from AMD with the extras (hydravision, etc.).  I used just the default Windows drivers. I have change the placement of the monitors on the video card, but few matter where I plug them in, only two works.  All monitors are operational.  I even tried different monitors.  All this with no result.  I tried to use the Catalyst Control Center.  He sees the third monitor but just shows it as being disabled with no way to enable that I see from in the Catalyst Control Center.

    It is the last obstacle for me to fully use this machine to Windows 8.  I'm puzzled.  I have read many other forums.  I've heard of this problem with Windows 7 as well so I don't know that it's specific to 8 but could very well be.  Yet once I had Windows 7 with three monitors with the same card.  Contribution to this issue would be greatly appreciated.

    I had this problem on a Lenovo three installation of the monitor using the integrated display laptop, a monitor outside the mini HDMI and a third follow out of the HDMI Port among Replicator.

    In the end, it's a simple solution.  When you go to display settings, all three monitors not reimbursed up to 1920 x 1080 and configuration could never be saved - however the 3rd monitor only supported by 1680 x 1050, which is the resolution (recommended).  After changing the 3rd monitor for the resolution recommended, I was able to save the configuration to display > screen without problem resolution.

    I don't know why the resolution not supported has been set default to-after selecting the right pair, there is now no option to go to the highest resolution not supported on this screen.

  • Two screen question: Control Panel appears on the screen 1 but the mouse is on the screen 2 and so I can't access

    I have a Sony Vaio laptop connected to a stand alone monitor. I don't use the laptop screen unless there is a problem and then I had to alternate between the two screens using Fn F7 key.

    A problem has occurred with the rundll32 process (which I'm trying to fix separately) and this led to the PC automatically flicking between screens and then stick with the independent monitor but in low resolution (so I couldn't access the tool bar along the bottom).

    I went to control panel to change the resolution to high, but the question of rundll32 kept close the process.

    This left me with icons on the desktop of the monitor stand alone, a white color on the laptop screen (it is normally black) and the ease of Fn F7 does not (said the service is not available).

    When I click on Control Panel on the screen of stand alone, it opens on the screen of the laptop, but I can't access it because the function of the mouse is on the screen to stand alone.

    Can someone help before I go out drinking?

    Thanks, Temp.

    I seem to have solved the problem. It seems that display order has been reversed and so I just had to move the mouse to the right of the screen to stand alone (I had been pushing against the left hand side) to move on the screen of the laptop. From there on, I played a bit with the display settings in the control panel and, although the issue of the always kept dllrun32 throw me out, seems to be back on the screen of stand-alone only, with the correct resolution and the Fn f7 works again. This means I can put the top back on bottle of vodka, at least until the next issue of dllrun32 arises.

  • If you use Firefox I can not long enlargement of two fingers to work on my Apple. The same site will expand using Safari, so I guess it has to do with Firefox

    If you use Firefox I can not long enlargement of two fingers to work on my Apple. The same site will expand using Safari, so I guess it has to do with Firefox

    Some actions have been removed in Firefox 4 and later versions.

    You can restore the zoom feature by changing the related values of downtown on the topic: config page.

    browser.gesture.pinch.in -> cmd_fullZoomReduce
    browser.gesture.pinch.in.shift -> cmd_fullZoomReset
    browser.gesture.pinch.out -> cmd_fullZoomEnlarge
    browser.gesture.pinch.out.shift -> cmd_fullZoomReset
    browser.gesture.pinch.latched -> false
    

    To open the topic: config page, type Subject: config in the address bar (address) and press the 'Enter' key, as you type the url of a Web site to open a Web site.

    If you see a warning then you can confirm that you want to access this page.

    • Use the filter at the top bar of the on: page config to more easily spot a preference.
    • Preferences that have changed see the bold (user set).
    • Preferences you can restore the default value or change via the context menu.
  • Hi, I wanted to know if you can fix the apple screen clock. the clock works perfectly, but the glass broke and how mach

    Hi, I wanted to know if you can fix the apple screen clock. the clock works perfectly, but the glass broke and how much

    Hi Maxi

    Costs vary depending on your location and the model Apple Watch.

    Contact Apple support to establish your repair options, cost and likely delays:

    http://www.Apple.com/br/support/watch/contact/

  • IPad can't drag, but screen work?

    I have an air of the IPAD, which suddenly works quite weird. The children said: asked to hit a message/selection and then the screen stopped to respond.

    Or almost stopped. Can I use the screen, but not by scanning and scrolling, etc. works pinch. I can tuch the box or the menu, and a square identify the button that is active - I can't double tab the menu/button and go on. It's the same with the 4-digit code. I have to first mark the number and then double the number tab.

    I did a reset/reinstall via the cable to the PC and itunes (dΘplaτant power button and home until the icon appears and I followed the instructions on the PC - ipad reinstalled and restarted the process - but it did not help)

    What experience children can be pure coincidence.

    What may have caused this and how to return correct touch screen features?

    I forgot - I have updated IOS yesterday to 9.2.1 (13D 15)

Maybe you are looking for

  • Unable to connect to the server

    I have an officejet pro 8600plus. When I bought it, I have activated ePrint and registered my printer, but never used the feature. Since then, I updated from XP to windows 8.1, changed a router and connected the printer through a series of switches o

  • Qosmio X 770-10 M - impossible to activate WLan using Fn + F8

    Hello I have a Qosmio X 770-10 M and I have a problem with the wireless.When I want to trigger on the system with the Fn key, told "the switch button is off, please turn it down."But there is no button on the Qosmio x 770... Maybe the switch is light

  • I want to convert my logic large table - multiply in a library called the faster, need some advice on the code of C.

    Hello everyone, In my VI, I have a code that looks like this- Each table is 2D size 512 by 640.  The time it takes to run this whole chain is approximately 28miliseconds. Seems fast, but I need to cut it to about 10ms.  I tried to make the tables 1 d

  • Are these real vulnerabilities and if yes, how can I fix them?

    Several identified via a Kasparsky Security Scan - "vulnerabilities" are these serious questions or not?  If so, what should I do to solve?  I use Windows XP SP 3 and, above all, the Firefox browser, although always use Internet Explorer, from time t

  • URGENT! Error while building project

    Hi all. Help me please with this one. I installed the BlackBerry JDE 4.7 1.6.0_0, jdk paths set in the two files 'bin' (jdk bin and bin bb jde). I'm trying to generate examples of jde 4.7 'HelloWordDemo' but an error message: "error during the genera