Canning Internet connection drops when the computer is connected to the PS3 via an Ethernet cable.

Similar Questions

• Connection from the desktop (Vista) to the WRTP54G via an Ethernet cable

  I replaced my old XP desktop with new Dell XPS One with Vista. The old office was connected to my router (WRTP54G - Firmware Version: 5.01.04) via Ethernet cable and worked like a charm. A new won't recognize this connection - is seen as "unidentified network" with "access: Local only". The wireless connection on the same office works, but I still don't understand why I can't it be connected via cable. My XP laptop is not yet had problems with this Ethernet connection to the router - it recognizes immediately as the connection to the local network and connects to the Internet.

  I suspect there is a problem with the WRTP54G in the Vista environment, because the Ethernet connection started work immediately after I have had bypassed the router and connected the office directly to the cable modem.

  Any help to fix this problem will be greatly appreciated.

  Give the 192.168.15.5 static IP address and the default gateway 192.168.15.1.

  Click on the Start button > Control Panel > Network and Sharing Center - slot, click 'Manage a network connection' - task do a right-click on the connection icon to the Local network and click Properties-on the 'Général' tab, select ' Internet Protocol Version 4 TCP/IPv4 ' and click on the button properties-select "Use the following IP address" - provide the IP - 192.168.15.5, subnet mask - 255.255.255.0 Default Gateway - 192.168.15.1 - favorite DNS 192.168.15.1, auxiliary DNS - 4.2.2.2 > click the Ok button to save and click 'Close' on the main properties window.

• LaserJet 4050 TN: Try to connect old Laserjet 4050TN via an Ethernet cable

  Hi, just inherited an old 4050 TN printer which I connected directly to my router using an RJ45 ethernet cable.

  My PC is connected via ethernet also cable to my router.  I can not get my PC or my network to recognize the printer.

  I tried to download the HP Universal HP.com and printing software that I hope, are the right drivers, but so far nothing that I allows me to connect the printer.

  I tried to add the printer to my homegroup, but Windows 10 always tells me that I can't create a homegroup on my PC, I don't know why it didn't, but I recently had to re - install windows 10 and my working group worked well previously.

  If anyone can point me in the direction of the correct drivers and installation software (do not have the original disk I'm afraid), that would be fantastic.

  Thank you

  My usual procedure would be to go through the printer menus and set IP DHCP configuration method.

  Then I would have to power cycle the printer with it plugged into the router and him give 2 minutes after getting a ready state and print configuration pages.

  On the configuration pages you will find the IP address that the router gave the printer, put this address in the location bar of a browser.

  Now you will look at the web server integrated in the jetdirect card and you can change it for an IP address manually so it will be the same after each power Cycle.

  I usually take the IP address assigned by the router and add about 22, in other words if it receives your printer an address ending the remplacer.24 par.4.

  You add the printer through the devices window and printers.

  Now, you can set up your device and that you add it to your selection of PC add local device, then you want to create a new TCP IP port.

  When you create the new port, you use the IP address that you gave your printer.

• How to connect an external device via an Ethernet cable with iPad Air?

  I need to connet to my iPad, a digital mixing console THE Behringer X Air xr18.

  LLA WiFi connection e/s is not overall durin live so I need to use the Ethernet cable.

  You can not unless someone makes a dongle, but even in this case an application had to talk with the dongle do not believe that a dongle could add something like kernel as a new network interface which could access normal applications

• I cannot connect to the Internet via an Ethernet cable but I am able to connect with other devices.

  Original title: deleted Ethernet adapter

  Hello

  All trying to fix my computer run Registry cleaners, I managed to delete my Ethernet adapter, I have taken steps to try to fix this problem and have been advice to visit Microsoft support for help.
  I have a Dell Dimension 5100 and am running Windows XP, I am unable to connect to the Internet via an Ethernet cable but I am able to connect with other devices.
  First of all, I contacted my Internet provider which forced me to various checks to see why I was getting a message saying acquiring network address and it seemed that I had no IP address and could not connect. He eventually get look in the network adapters Device Manager, he demonstrated Intel PRO/100 VE network connection that is activated in the State shows that it works, but there is no Ethernet adapter shown in this place.
  I tried to insert Dell drivers and utilities disk, but that does not change.
  I tried to download on an other computer files from dell that look like they are pilots.
  I tried to set up a new connection
  None of what I tried so far seems to have worked, can anyone suggest what I can do to fix this?
  Thank you
  Kevin

  Hello

  1. what you're trying to fix by running registry cleaners?
  2. How did you remove Ethernet card?
  3. How are you online using other devices?
  4. What are the devices are?

  Intel PRO/100 VE network connection is the Ethernet adapter on your computer. The following articles may be useful:
  How to troubleshoot possible causes of Internet connection problems in Windows XP
  http://support.Microsoft.com/kb/314095
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• I have my printer connected to my router via a usb cable... I also have my (Vista) computer connected to the router by ethernet cable. How can I set the computer to print on my prints through the router?

  I have my printer connected to my router via a usb cable. I also have my (Vista) computer connected to the router by ethernet cable. How can I set the computer to print to my printer via the router?

  Usually, you need to install the printing software / drivers on your PC, configured / installed specially for a printer "remote" (its an option in the installation of the printer software)

• E1000 connect a PC via an ethernet cable

  Using Windows 7 with a Cisco/Linksys E1000 router

  I have successfully implemented a computer laptop and desktop with wireless, but now wan router to set up my office to the router with an ethernet cable. I connect the ethernet cable to port LAN 1 of the router and the ethernet port on my PC

  but the PC shows that my wireless connection and

  the network and sharing Center shows a network of "Unidentified" with connection to the Local network and internet access

  How to configure the unidentified local network connection to connect to the internet

  Thanks for your help

  Disable your wireless connection

  Start > connect to > show all connections > and disable the wireless, while there, check your "wired" connection to the local area network properties. Click right and in the general tab, select TCP/IP and click Properties and configure it to your network, probably you want to get the IP and DNS services automatically. Save settings and close. You shouldn't have to restart to see the changes. I hope this works!

• Problems connecting an Officejet 7310, wireless and ethernet cable

  My printer (Officejet 7310) is connected to two PCs with an ethernet cable and the router. Now I want to install a laptop as well.

  I know that the lap top is communicating with the wireless router, but I can't get the laptop to recognize that there is a printer is installed.

  I tried to connect the printer directly (via Ethernet cable) to the laptop and it works fine. I downloaded the latest version of the software for the 7310 and used two options (without wire and cable).

  Any help would be most appreciated.

  Cutting the anti-virus made no difference.

  I HEALED NOW THE PROBLEM!

  Installed a new router 2wire.

  Thanks a lot for your help.

• Satellite A80: Failure to connect to the internet via an ethernet cable

  I'm having problems to get an internet connection via a cable ethernet to my office. The laptop works everywhere else, but not in the office. The strangest thing is that my desktop at the office computer works perfectly with the same cable.

  The icon in the taskbar of configfree reads "MARVELL YUKON 88E8036 PC... 169.254.95.8"no matter how many times I disconnect and reconnect it to my office. Curiously, the IP Office when it is connected to the same cable is 192.168.1.69.

  I was told to change the tcp/ip properties manually, but I'm not able to do because I have not all entries in the NETWORK CONNECTIONS or can't seem to create a new.

  I would be grateful if anyone has any suggestions.

  Hello

  I wonder why you have no entries for network connections.
  Click Start-> settings-> network connections-> connections to the Local network-> properties

  Select the Internet Protocol (TCP/IP), and then click Properties.
  If you use a server in your office and the IP address is assigned automatically then all TCP/IP parameters must be on automatically

  Check it!

• Pavilion 17-f113dx: Internet becomes slow when the charger is unplugged

  Hi all

  I have a problem with Internet on my computer whenever I unplug the charger internet connection goes down, I need to plug back in so I can use internet properly. The question began only a few days when windows update prompted me to install the new drivers wifi. My laptop is a HP Pavilion f113dx 17.

  Hope someone can help, thank you. Nice day.

  @Albie08

  Welcome to the Community Forum of HP.

  It's unfortunate - both drivers Wireless illustrated the State of your laptop Driver Support page specfically this version should improve (and certainly not degrade) performance.

  Ideas

  ---------------------------------------------------------------------------------

  Assuming that you have chosen to create a Restore Point before you make these changes to your computer, you can easily "pass in time" from before the last set of updates have been installed.

  Using Microsoft System Restore (Windows 8)

  ---------------------------------------------------------------------------------

  Use your Recovery Manager to install the original Wireless driver that was preinstalled on your computer, while he was 'new ':

  This document explains how to reinstall hardware drivers and software that were originally installed on the computer at the factory.

  Using Recovery Manager to restore the software and drivers (Windows 8)

  ---------------------------------------------------------------------------------

  Boost the signal on your network wireless when running on the battery.

  See

  Parameters to improve wireless connectivity

  Section:

  Laptop wireless hesitates or does not work when executing a stack

  ---------------------------------------------------------------------------------

  For later - you must let not updates sneak up on you - or allow automatic updates to update the system without having you the time to decide whether it is convenient or critical the right time for this task.

  Updates - when and how

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' Kudos on this post.

  Click on accept as Solution when my answer provides a fix or a workaround!

• I have an Acer Travelmate 5620 running XP Pro with a Realtek Pcie GBE Family Controller. I connect to the web using an ethernet cable but should go to the network in the control panel and click Activate to connect. I want to be able to connect when I boot

  Internet connections

  Hello Daton,

  Thank you for your message.  Please ensure that the following setting is correct:
  Click 'Start' > right click on 'My computer' > select 'manage '.
  Select Device Manager.
  Double-click "network adapters."
  Less you should see your network adapters, double-click on each of them and ensure that they are ready to "Enable".
  Please let us know if this solves your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Can not connect Equium M70 to the Internet via an Ethernet cable

  I have recently install wide telewest broadband via the installation disc. I used the provided ethernet cable. During installation, I received an error message stating that it could not connect due to various problems.
  After a long discussion with the customer service and try several solutions over the phone we wouldn't always get connection using the ethernet cable.
  Telewest has also provided a USB cable so I was told to remove the ethernet connection and plug in the USB. The connection has been made instantly.

  Has been informed by the technical support of Telewest, that I had a problem ethernet on the laptop. This could be correct, or maybe it was an ethernet cable from the spleen.
  Any suggestions? My laptop is only four months.

  Hello

  It is not easy to believe that the network adapter does not work on your laptop. What is the status of LAN in Device Manager? When the cable is connected is the assets of orange or green led or not? Try also to start ConfigFree tool. Under the physician connectivity tab, you can see their actual situation and if there is a problem of communication it will be shown here.

  If there is any attempt of trying to test it on another network (perhaps in your company).
  You can also contact your dealer and allow it to check the device. It can be done in the store and may not take a lot of time.

• How to store Internet Explorer running when the screen is locked?

  Hello! So, I am owner of a Surface... Yes! Somehow...

  Because Microsoft App Store refuses to give us of Pandora, Youtube and other needed applications, the only way to use these pages is through Internet Explorer...

  (in my opinion, they do it so that someone using Internet Explorer)

  Now, ok, I did that! I search for the pages I need and have pin them at the beginning... Yes, problem solved?

  NO.... The screen, if you don't touch anything, or move the cursor or something, it locks itself automatically after a certain time... and the music and the videos just stop playing.

  Now, when I go to Internet Options, I can't find anything to fix this. Change PC settings or... In customize, where it says lock screen Apps, it gives you the opportunity to choose "the apps run in the background...". ", but Internet Explorer is not available for this.

  Now, someone, anyone... tell me how that's possible! How can I leave Pandora running or a 1 hour running YouTube video?

  What are my options?

  1. setting of the Tablet does not interrupt or stop using the internet explore when the screen is locked... Is it still possible?

  2. the Tablet for only auto setting not lock screen when I use some applications, such as Internet Explorer (again probably not possible)

  3 magically App Store makes it available Youtube Pandora Facebook and other necessary apps (pfffff apparently does not have to spend)

  4. all that have worked for you guys... Any Suggestions?

  These are just little things that have made use of my annoying and incompetent little practical Surface... It's sad when smartphones can be more useful and practical than my Surface... really really sad. This comes from someone who wants this work effective and favourable way to the customer.

  Thank you for reading, for help, for viewing and understanding, I hope that I'm not the only one with this problem!

  > How can I leave Pandora running or a 1 hour

  You could try PRadio in the store:

  PRadio is a third Pandora Internet Radio App for Windows 8 modern.  It allows users to listen to music from the Pandora recommendation service in the background.

  Kate

• Several drag and drop - when the correct triggers something

  I am very new to Flash, so I hope that what I try to do is not beyond my capabilities.

  I want to create a game in which you have to drag and drop three correct items for a target area. When the three correct items are removed, the game should move forward to the next part.

  I tried to get help on this, but I don't know what exactly I should look for (IE what terms, keywords).

  Any help would be much appreciated, even if it's just to tell me the terms Flash I need to point me in the direction of assistance.

  Thank you!

  Here are a few terms to look on...

  startDrag()

  stopDrag()

  _droptarget

  hitTest()

  If you search Google using terms such as "StartDrag AS2 tutorial", you may be able to find something that describes everything what you want for your design

• Z580 help: connect to the TV via a HDMI cable

  I recently had my father the IdeaPad Z580. It is really eager to stream its videos and watch them on TV. I connected it today via a HDMI cable and got really excited when the screen was reproduced on the TV... but then, when I clicked on internet Explorer tile, I got the following error message:

  This application cannot open
  The screen resolution is too low for this application to run.
  Change your screen resolution

  Seems simple enough... but really did not have a clue what to do! Doesn't help that I'm a complete newbie to Windows 8!

  I'd be really grateful if someone here would be able to help / tell me what to do! ^^

  Thanks in advance!

  All of a sudden it works without enaything. In fact, I just do a windows 8.1 update.