Cannot access our local network Web site
We have just added a Cisco ASA5510 to protect our network. Everything works except that no one in the local network can access our imail we site. Web site points to one of our public IP address, x.x.x.35 (we have access to the web site of outside and we can just? t do inside even after the addition of the ASA). Is it possible inside computers can access our web site using the public IP address? If not, my another option is to set up a record DNS pointing to the web site, for example 192.168.0.213 = www.chicagotech.net (name of the network domain is chicagotech.local)? I can? t find a way to do it. Any suggestions?
This is the Cisco ASA configuration.
ASA Version 7.0 (5)
!
ciscoasa hostname
domain default.domain.invalid
names of
DNS-guard
!
interface Ethernet0/0
nameif outside
security-level 0
IP address x.x.x.38 255.255.255.248
!
interface Ethernet0/1
nameif inside
security-level 100
IP address 192.168.0.250 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
no ip address
management only
!
passive FTP mode
out_to_inside list extended access permit tcp any host x.x.x.34 eq www
out_to_inside list extended access permit tcp any host x.x.x.34 eq 8080
out_to_inside list extended access permit tcp any host x.x.x.34 eq 8383
out_to_inside list extended access permit tcp any host x.x.x.35 eq www
out_to_inside list extended access permit tcp any host x.x.x.34 eq smtp
out_to_inside list extended access permit tcp any host x.x.x.34 eq pop3
out_to_inside list extended access permit tcp any host x.x.x.34 eq 3389
out_to_inside list extended access permit tcp any host x.x.x.34 eq 13001
out_to_inside list extended access permit tcp any host x.x.x.35 eq 13001
out_to_inside list extended access permit tcp any host x.x.x.35 eq 3389
out_to_inside list extended access permit tcp any host x.x.x.35 eq pop3
out_to_inside list extended access permit tcp any host x.x.x.35 eq smtp
out_to_inside list extended access permit tcp any host x.x.x.35 eq 8383
pager lines 24
asdm of logging of information
management of MTU 1500
Within 1500 MTU
Outside 1500 MTU
ASDM image disk0: / asdm505.bin
don't allow no asdm history
ARP timeout 14400
Global interface (10 outside)
NAT (management) 10 0.0.0.0 0.0.0.0
NAT (Inside) 10 0.0.0.0 0.0.0.0
static (inside, outside) x.x.x.34 192.168.0.213 netmask 255.255.255.255
static (inside, outside) x.x.x.35 192.168.0.112 netmask 255.255.255.255
Access-group out_to_inside in interface outside
Route outside 0.0.0.0 0.0.0.0 x.x.x.33 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00
Timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
If inside users try to connect to the public IP address then, it won't work. How do fix you this depends on where is your DNS server.
If inside users use a DNS server on the external interface, and then you can have the ASA change the DNS response during its passage through the ASA. Just add the option "dns" on the end of your static controls so that they resemble the following:
static (inside, outside) x.x.x.34 192.168.0.213 netmask 255.255.255.255 dns
static (inside, outside) x.x.x.35 192.168.0.112 netmask 255.255.255.255 dns
If inside users use a DNS server on the inside, but this server responds with the public IP address, so you'll have to change within a file so that it points to your local IP address 192.168.0.21x. No other way around it, I'm afraid.
Tags: Cisco Security
Similar Questions
-
ASA 5505 IPSEC VPN connected but cannot access the local network
ASA: 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
Pool VPN: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.
I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.
Here is my setup, wrong set up anything?
ASA Version 8.2 (5)
!
hostname asatest
domain XXX.com
activate 8Fw1QFqthX2n4uD3 encrypted password
g9NiG6oUPjkYrHNt encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.1.1.253 255.255.252.0
!
interface Vlan2
nameif outside
security-level 0
address IP XXX.XXX.XXX.XXX 255.255.255.240
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain vff.com
vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0
access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
logging trap warnings
asdm of logging of information
logging - the id of the device hostname
host of logging inside the 10.1.1.230
Within 1500 MTU
Outside 1500 MTU
IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol nt AD
AAA-server host 10.1.1.108 AD (inside)
NT-auth-domain controller 10.1.1.108
Enable http server
http 10.1.0.0 255.255.252.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 10.1.0.0 255.255.252.0 inside
SSH timeout 20
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntest strategy
Group vpntest policy attributes
value of 10.1.1.108 WINS server
Server DNS 10.1.1.108 value
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the password-storage
disable the IP-comp
Re-xauth disable
disable the PFS
IPSec-udp disable
IPSec-udp-port 10000
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntest_splitTunnelAcl
value by default-domain XXX.com
disable the split-tunnel-all dns
Dungeon-client-config backup servers
the address value vpnpool pools
admin WeiepwREwT66BhE9 encrypted privilege 15 password username
username user5 encrypted password privilege 5 yIWniWfceAUz1sUb
the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username
tunnel-group vpntest type remote access
tunnel-group vpntest General attributes
address vpnpool pool
authentication-server-group AD
authentication-server-group (inside) AD
Group Policy - by default-vpntest
band-Kingdom
vpntest group tunnel ipsec-attributes
pre-shared-key BEKey123456
NOCHECK Peer-id-validate
!
!
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege show import at the level 5 exec mode command
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege, level 3 see fashion exec command eigrp
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege see the level 3 exec command mode dynamic filters
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
privilege clear level 3 exec command mode dynamic filters
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end
Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.
The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.
On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.
-
Cannot access a local network of off Site 2 Site VPN
I have cisco ASA 5515-X and 8818 cisco router device
I configured vpn site-to-site. the cisco ASA is a new device but the router is a device in another location and contain several tunnel work, now the tunnel is up but I can't ping LAN on the site of the ASA firewall and some time tunnel at the end of the asa will disappear while it will show again at the end of the router
Here is the config of the SAA.
# show running-config
: Saved
:
ASA 9.1 Version 2
!
CITGroup hostname
activate the encrypted password of V9WHcFD3Zaeul5Lr
names of!
interface GigabitEthernet0/0
nameif outside
security-level 0
address IP A.A.A.A 0.0.0.0
!
interface GigabitEthernet0/1
nameif inside
security-level 100
address IP B.B.B.B 0.0.0.0
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa912-smp - k8.bin
passive FTP mode
network obj_any object
subnet 0.0.0.0 0.0.0.0OFFICE of extended access list permit ip (IP local ASA) (local IP of the router)
outside extended access list permit tcp any any eq ssh
outside allowed extended access list tcp any host (local IP address of ASA) eq ssh
outside extended access list permit icmp any one
outside extended access list permit tcp host (the router's local IP) host (local IP address of ASA) eq sshpager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 713.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
Route outside 0.0.0.0 0.0.0.0 D.D.D.D 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.1.0 255.255.255.0 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set esp-aes-256 TEST esp-sha-hmac ikev1
Crypto ipsec pmtu aging infinite - the security association
crypto map outside_map 1 is the OFFICE address
card crypto outside_map 1 set k.k.k.k counterpart
outside_map 1 set transform-set TEST ikev1 crypto card
outside_map interface card crypto outside
trustpool crypto ca policy
Crypto ikev1 allow outside
IKEv1 crypto policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 2
preshared authentication
3des encryption
md5 hash
Group 2
lifetime 28800
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
username admin password encrypted JtdUVwNnMzvEjPfJ
nairtime Fyp1BJjsayu55viz username encrypted password
tunnel-group k.k.k.k type ipsec-l2l
k.k.k.k group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:e658de2652c6702c61a0cc854a47415f
: endYou are missing a nat exemption, follow the example below, replace IP subnet object-group, depending on your environment.
object-group network local-ASA-lan
object-network 10.10.1.0 255.255.255.0object-group network remote-router-lan
object-network 10.200.0.0 255.255.255.0NAT source (indoor, outdoor) static local-ASA-lan lan-ASA-local destination distance-router-lan lan-router-remote control no-proxy-arp static
Thank you
Rizwan James
-
Cannot access emails Outlook Express Web sites
I run Windows XP on my computer at home and use outlook express for e-mail. I can access is no longer ANY link of website of my emails. I had this problem for about 2 months. I get the following error message: "this operation has been cancelled due to restrictions in effect on this computer. Please contact your system administrator. "I have not changed the settings on the computer, so I guess it might be a recent automatic update. Can you help me to fix this? Thanks for any input!
Hello
Run the fix it link and check if this may help: you receive an error message when you click a hyperlink in Outlook: http://support.microsoft.com/kb/310049 (The FIx is valid for Outlook Express)
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK
I tried to set up a simple customer vpn using this document
VPN IS CONNECTED BUT CANNOT ACCESS THE INTERNAL NETWORK BEHIND "RA"...
6.3 (5) PIX version
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the encrypted password of VmHKIhnF4Gs5AWk3
VmHKIhnF4Gs5AWk3 encrypted passwd
hostname VOIPLABPIX
domain voicelab.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list 101 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 101 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 102 permit ip 172.10.2.0 255.255.255.0 172.10.3.0 255.255.255.0
access-list 102 permit ip 172.10.1.0 255.255.255.0 172.10.3.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside 208.x.x.11 255.255.255.0
IP address inside 172.10.2.2 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool voicelabpool 172.10.3.100 - 172.10.3.254
history of PDM activate
ARP timeout 14400
NAT (inside) - 0 102 access list
Route outside 0.0.0.0 0.0.0.0 208.x.x.11 1
Route inside 172.10.1.0 255.255.255.0 172.10.2.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 172.0.0.0 255.0.0.0 inside
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-aes-256 trmset1, esp-sha-hmac
Crypto-map dynamic map2 10 set transform-set trmset1
map map1 10 ipsec-isakmp crypto dynamic map2
client authentication card crypto LOCAL map1
map1 outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 encryption aes-256
ISAKMP policy 10 sha hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup address voicelabpool pool cuclab
vpngroup dns 204.x.x.10 Server cuclab
vpngroup cuclab by default-field voicelab.com
vpngroup split tunnel 101 cuclab
vpngroup idle 1800 cuclab-time
vpngroup password cuclab *.
Telnet timeout 5
SSH 208.x.x.11 255.255.255.255 outside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 172.10.1.2 255.255.255.255 inside
SSH timeout 60
Console timeout 0
username labadmin jNEF0yoDIDCsaoVQ encrypted password privilege 2
Terminal width 80
Cryptochecksum:b03a349e1ac9e6022432523bbb54504b
: end
Try to turn on NAT - T
PIX (config) #isakmp nat-traversal 20
http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml#Solution1
HTH
-
Error when trying to access the microsoft update web site
I am using windows XP Pro. SP3 32-bit (build 2600.xpsp_sp3_gdr.100216 - 1514)
I have IE v8.0.6001.18702
When I access the microsoft update web site, I get a message saying that I need to update windows update and I want that allows. No matter what I said or after 30 seconds have elapsed if I do nohting I get the message:
- The instruction at "0 x 08100068" referenced memoery to '0 x 08100068', the memoery could not be "written".
The address is different from one attempt to another, but both are still the same as eachother.
When I close this tab IE grave message box down and I get the message 'recovered tab' normal.
Can I search / install updates using vbscript widely available, or automatic update installation of windows. The problem only occurs when you try to access the web site itself.
I tried to download and install the latest windows update manually, but this does not solve the problem.
I am unaware of the date of the last update because I'm unable to access the update log.
I use a current version of McAfee Anti-virus.
I think my windows is a clean install, but I didn't do it, so I can't be 100% certain.
Jacob
I uninstalled ie8 and found ie7 under him.
I am able to access the site WindowsUpdate using ie7.
Jacob
-
Malwarebytes 'has managed to block access to potentially malicious Web site.
Hello
Did someone have the problem I, m very experience regularly I run win 7 Home Edition and constantly I, m getting this message.
I use utorrent to my D/L without any problem at all, but this message on my T/Bar. I regularly run the Malwarebytes Anti Malware to make sure that my pc is not infected message is... Malwarebytes 'has managed to block access to potentially malicious Web site... " Type the incoming port is and treat: utorrent. can exe I ask for your help to remove this annoying message.
Thank you
DennisHi Dennis!
I suggest that check you the answers here: http://www.malwarebytes.org/support/consumer/
See you soon
Julia -
Easy VPN not able to access the local network
Hi guys,.
little hope can help me, I'll give you a run down on the config.
I have a border router that is a no. 2851 connected to the No. 2851 is a switch cisco 3750 running Routing inter - vlan with four VLANS.
I have easy VPN server on the edge router No. 2851 I am able to connect remotely from a client vpn cisco with a problem but I can't access the local network on the server, I tried everything with no luck.
I have a cisco VPN client installed on a 64-bit windows system 7 and I also tried with windows xp 32-bit system and still no luck.
Please I need help I need to get this race to end of trading today.
I will be copying and pasting the edge router config please if someone get review and see if the config is good.
You need to change your ACL PAT of standard to extend and to deny traffic to be translated to the Pool of VPN:
access-list 120 deny ip 10.10.10.0 0.0.0.3 10.10.50.0 0.0.0.255
access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 172.16.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 172.1X.20.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 allow ip 10.10.10.0 0.0.0.3 all
IP access-list 120 permit 192.168.XX.0 0.0.0.255 any
IP access-list 120 permit 172.16.XX.0 0.0.0.255 aniy
IP access-list 120 permit 172.1X.20.0 0.0.0.255 any
IP access-list 120 permit 192.168.XX.0 0.0.0.255 any
overload of IP nat inside source list 120 interface Dialer0
no nat ip within the source of the list 1 overload interface Dialer0
clear the ip nat trans *.
Hope that helps.
-
How to configure IIS6 on windows 7 to allow access to the default Web site or there at - there someone out there who can put up my computer at a reasonable rate of legend
Hello
The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
http://social.technet.Microsoft.com/forums/en-us/winserverfiles/threads
-
Cannot view or access my local network of 'my network places '.
Since the evolution of my router to router ZyWEL I can't diplay or access other computers on my local network. The entire network is invisible from all computers.
Mallorcan salvation,
Are a. When you facing this problem?
B. you get errors?
C. do you have a cable or a wireless network connection?
D. the router is not compatible with vista?
Have e. you checked if a firewall blocks the router?
First check to see if a firewall is blocking the router then try the procedure below.
Open Network Diagnostics by right-clicking the network icon in the notification area, and then click diagnose and repair.
Make sure that all cables are connected (for example, make sure that your modem is connected to a working jack or cable phone connection, either directly or through a router).
If you try to connect to another computer, make sure that this computer is turned on and that you have enabled file and printer sharing on your network. For more information, see networking of computers running different Windows versions.
If your computer has a wireless network adapter, Windows automatically detects wireless networks that are located nearby. To see a list of wireless networks that Windows has detected, click the Start button and then click on connection to. If Windows does not detect a network that you think is in range of your computer, open help and Support and search for "Solving problems finding wireless networks."
Try not the articles below.
The problems of finding computers on a home network
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-computers-on-a-home-networkSolve problems with computers not appearing is not in the network map
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-computers-not-appearing-on-the-network-mapNetwork connection problems
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problemsI hope this helps.
Bindu S - Microsoft Support
[If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]
-
Cannot update or load the Web site.
Hi, my name of Chris and I bought a MacBook Air off of eBay about 2 years ago and I decided to use it and I noticed that I was on the version of Mac OS X 10.6.8 and he decided to search for software updates. As soon as I tried to check, he would fail and a pop up appears saying "Update software cannot verify updates due to a network problem". I am absolutely convinced that my internet connection completely works because I just got about 1 week ago. I am sorry to ask a lot, but another problem I have is that whenever I go online, some site not loading and under him, it appears "ERR_EMPTY_RESPONSE". On the Web site like YouTube and Apple Discussion of work. It would help if someone could help me solve these 2 problems.
You have access to another network where you can see if you still have the same problems? This will help determine if there is a problem with the network or computer.
Did you reboot / reset the router?
Connection to the problems of the App Store
Connection to the problems of the App Store (2)
Safari does not load a page or webpage elements are missing
Safari / other browsers - Web site does not
Try a reboot.
Make a backup using Time Machine or a cloning program, to ensure that data files can be recovered. Two backups are better than one.
Try to set up another admin user account to see if the same problem persists. If back to my Mac is enabled in system preferences, the guest account will not work. The intention is to see if it is specific to an account or a system wide problem. This account can be deleted later.
Isolate a problem by using a different user account
If the problem is still there, try to start safe mode using your usual account. Disconnect all devices except those necessary for the test. Shut down the computer and then put it up after a 10 second wait. Immediately after hearing the startup chime, hold down the SHIFT key and continue to hold it until the gray Apple icon and a progress bar appear. Startup is considerably slower than normal. This will reset some caches, forces a check for directory and disables all start-up and connection, among other things. When you restart normally, the initial restart may be slower than normal. If the system is operating normally, there may be 3rd party applications that pose a problem. Try to delete/disable the third-party applications after a reboot using the UN-Installer. For each disable/remove, you need to restart if you do them all at once.
-
Unable to access the Windows Update Web site.
When you try to access the Microsoft Windows Update site, the following occurs. the Web page that says "checking to see if you have the latest version of..." "is displayed briefly. It is immediately replaced by a page of information. This has "[error number: 0x800A0005] the website has encountered a problem and cannot display the page you are trying to display." The options provided below may help you solve the problem,"with the other possibilities in clickable (I went through them but nothing helped...
I tried Microsoft FixIt Center, but all she could do is to tell me that "necessary attachment components" but not which.
I also tried to reset Windows Update components according to the instructions on "http://support.microsoft.com/kb/971058".. .no luck.
I am running XPPro SP3 IE8.
Symantec Endpoint Protection version 11.0.7101.1056.
Any help much appreciated.
Hello
Perform the steps mentioned below and check if that helps:
Method 1
Check if the Windows Update Service is selected as a starting point.
To do this, follow these steps:
1. on Start, run and type services.msc in the Open box, and then click OK.
In services.msc find the automatic updates service and double-click it.
1. click on the tab log and ensure that the "Local System account" is selected for the account logon and the box "Allow service to interact with desktop" is DISABLED.
2. in the hardware profile sectionin the log tab, check that the service is activated.
3. on the general tab, the Startup Type should be Automatic, otherwise, the drop-down list box and select automatic.
4. under "Status of Service" under the general tab, the service must be started, click the Start button enable.Repeat the above steps for the service "BITS Background Intelligent Transfer Service ()".
Method 2:
You can also re - register dll in Windows Update.
To do this, follow these steps:
1. Start, run, type CMD and click ok
2. in the black command window, type the following command and press enterREGSVR32 WUAPI. DLL
Wait until you receive the "DllRegisterServer in WUAPI. DLL succeeded"message and click OK."
* Repeat the same step for each of the following commands:
REGSVR32 WUAUENG. DLL
REGSVR32 WUAUENG1. DLL
REGSVR32 ATL. DLL
REGSVR32 WUCLTUI. DLL
REGSVR32 STINKS. DLL
REGSVR32 WUPS2. DLL
REGSVR32 WUWEB. DLLMethod 3:
Delete the corrupted Windows Update files. To do this, follow these steps:
a. at the command prompt, type the following command and press enter
net stop WuAuServ
b. at the command prompt,
type cd %windir% , and then press enter
c. in the opened folder, type the following command and press ENTER to rename the Software Distribution folder
Ren C:\Windows\SoftwareDistribution SD_OLD
d. restart the Windows Update Service by typing the following at the command prompt
net start WuAuServ
Type Exit and press ENTER to close the command prompt.
e. restart the computer and check if you have a similar question.
For reference:You can access the event viewer on your computer and check the newspaper of windows for messages/error codes important related to the question and after return from errors in the event viewer.
See the link below for more details:
What are the information contained in the logs of the event (Event Viewer)?
http://support.Microsoft.com/kb/308427
Let us know if it helps.
-
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
Cannot access the local admin page after first start
Hello
I am not able to access my newly purchased RN202, SN 45Y2535W003FC. I just plugged the power cable and turned on, but the power light keeps blinking even after hours. The NAS will connect to my local network with the ip 192.168.178.32 and ends by RAIDar under this address. However, the local admin under https://192.168.178.32/admin and https://192.168.178.32 page (even with http://) is not accessible. The connection is not accepted (cannot be connect-page in the browser). Also access more ReadyCLOUD is not possible, because the NAS cannot be discovered. Currently, there are no hard drives in the NAS. I also tried to insert a HARD disk already formatted in combination with a factory reset, but it does not work with the same result. It's already a replacement unit by my retailer the first device showing the same behavior, so I excluded a technical defect. What I am doing wrong? Any help would be greatly appreciated.
Best regards
Patrick Schmidt
OK I found the solution by myself. Without a HARD disc inserted the NAS will not start correctly. As mentioned, I already tried to insert a HARD drive and then do a factory reset. Now, I saw that I have is to not properly place the HARD disk. If you open the lock on the grid (the thing in which you put the HARD drive), then you can not insert in the case completely and do not connect the connector of power und data. Maybe a little more detailed manual on it (for Dummies like me) would be useful. Argh...
Maybe you are looking for
-
adapter reports by wireless button disabled HP wireless assistant
I think it's telling me that the wireless on / off button with many laptops is DISABLED but the HP Pavilion dv7 (product number: WV705AV) has no wireless button. I think that windows update has changed the driver to the model bad which reported Devi
-
HP Web site shows that this laptop is a 4th Gen Intel (r) Core i7-4722HQ Quad Core with NVIDIA GeForce GTX 950 M 4 GB graphics discrete. My question is, can someone check what version of the GTX950M the laptop contains? What is the DDR3 or GDDR5 vers
-
Cannot package App when upgrade webworks 1.0.2.9
I could package app within the ripple with webworks 1.0.0.17, but failed for packing when upgrade to 1.0.2.9. Got the msg of error as below. I hope someone can help. Thank you. I use win7 64 bit, installed 1.6e 64-bit java, ripple v0.9.10. Because of
-
Autoamtically ACS5 email reports?
Hi all Is it possible that I can get GBA (5.3) to send some of its reports on a schedule? I hope to send automatic summaries of the failures of connection for the service desk every Monday morning. I don't see any way to do it! M
-
AutoFill the form based on the input field
Hey everybody,I have a form on the EMP table, with a text field containing the empno.When I get a (valid) empno, I want to give all the necessary information (ename, job,...) automatically in the fields.I read somewhere that I just write a query for