Cannot access the Web Configuration of RE1000 page once I have connected to my wireless network
I can't access the Setup page of my wireless range Extenders RE1000 via IP 192.168.1.1 address once I have connected the Extender to my wireless network. I was connected to the router via my mac and even took my mac out of wireless networks (just to be sure he wasn't trying to get to the IP 192.168.1.1 wireless.
It happened a few times. After it happened the first time I reset the access point and was able to get back to the web administration page. I updated the firmware and exactly the same problem repeated once I plugged in my network home.
This is a security feature? (Perhaps once it's on the wifi network you don't want just anybody access admin functions...?) A bug? Or something else?
Thank you
If you don't set a static on the RE when IP address configure it on the connection of the SSID, it will grab an IP address from the router. You need to look in the router DHCP client table to find the RE of the new IP address. You can also use a reservation DHCP from the router to assign an IP address to the STIMULUS, but static IP is the best.
Tags: Linksys Routers
Similar Questions
-
Cannot access the web configuration utility - server wrote: level_15_access
I've been using a Dlink router and wasn't getting any beach on my network, so I tried to configure my router linksys wrt150-n v1.1. I pressed the button reset for 20 seconds, then unplugged my modem (cable) and the router, then plugged in. When I open a browser window and type http://198.162.1.1, instead of open the configuration page, I get a message saying "the http://198.162.1.1:80 server requires a user name and password. "The server said: level_15_access.
I left the empty user name and used the password default admin, and who does nothing.
Tried to reset the router on 4 or 5 times without success. Any ideas on what I forget? I did not initially provided with the router Router installation CD, and it is not a downloadable file - I should be able to and have in the past been able to use the default IP address and the admin PW.
Thank you!
Try a Hard Reset:
Hard Reset (aka 30/30/30 reset):
The following procedure will clear the memory NVRAM and set dd - wrt return to default values:
- With the power on, press and hold the reset button the back of the unit for 30 seconds
- Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
- Plug in the appliance ALWAYS keeping the reset button a final 30 seconds
-
cannot access the web page of WAP but can telnet
Can someone tell me why the following configuration won't let me access the web page of the WAP?
version 12.2
no service button
horodateurs service debug datetime localtime
Log service timestamps datetime localtime
encryption password service
!
hostname EwingWAP
!
logging buffered information
enable secret 5 $1$ z9vV$ M.rY40womPNf7YPOQqC8T.
!
username privilege 15 secret 5 careone $1$ nFXA$ ezjkiBAHeboaKYMzB4hpq.
clock timezone IS - 5
clock to summer time EDT recurring 2 Sun Mar 2:00 1 Sun Nov 02:00
IP subnet zero
!
!
Bridge IRB
!
!
interface Dot11Radio0
no ip address
no ip route cache
!
SSID tsunami
open authentication
Comments-mode
!
base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
threshold RTS 2312
root of station-role
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
Bridge-Group 1 covering-disabled people
!
interface FastEthernet0
no ip address
no ip route cache
automatic duplex
automatic speed
Bridge-Group 1
No source of bridge-Group 1-learning
Bridge-Group 1 covering-disabled people
!
interface BVI1
IP 172.18.86.5 255.255.255.0
no ip route cache
!
default IP gateway - 172.18.86.1
IP http server
IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivor
y/1100
radius of the IP source-interface BVI1
1 channel ip bridge
!
!
Line con 0
line vty 0 4
local connection
line vty 5 15
local connection
!
NTP-period clock 2860650
NTP 208.90.144.53 Server
endHi Jason,
Have you tried the default user name and password?
Username - Cisco
Password - Cisco
Please try the commands below and let me know how it works...
en
conf t
AAA new-model
local IP http authentication
end
Try to open the WEB GUI by using the configured user name and password...
Concerning
Surendra -
Help, please! Cannot access the web after connected to the VPN
Hello
I'm a newbie on Cisco products. I configured a Cisco ASA 5505 with VPN firewall. However, I can't access the web after I connected to the remote IPSec VPN. I also cannot connect to the bands using the intellectual property. But I can connect to the internal servers in the office with no problems.
Here is my setup, can someone help please? Thank you very much
ASA Version 8.2 (5)
!
host name asa
xxxxxxxxx.com domain name
enable the encrypted password xxxxxxxxxxx
xxxxxxxxxxx encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
passive FTP mode
area of zone clock - 8 schedule
clock summer-time recurring PDT 1 Sun Apr 02:00 last Sun Oct 02:00
DNS lookup field inside
DNS server-group DefaultDNS
Server name 107.204.233.222
name-server 192.168.1.3
xxxxxxxxx.com domain name
inside_nat0_outbound list of allowed ip extended access all 192.168.1.96 255.255.255.240
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 192.168.1.0 255.255.255.0
NAT (inside) 1 0.0.0.0 0.0.0.0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH timeout 5
Console timeout 0
interface ID client DHCP-client to the outside
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.36 inside
dhcpd dns 107.204.233.222 inside the 192.168.1.3 interface
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal strategy group xxxxxxxx-sc
attributes of xxxxxxxx-sc group policy
value of 107.204.233.222 DNS server 192.168.1.3
Protocol-tunnel-VPN IPSec
XXXXXXXXXX.com value by default-field
xxxxx xxxxxxxxxxx encrypted password username
Strategy Group-VPN-xxxxxxxx-sc
remote access to tunnel-group xxxxxxxx-sc type
attributes global-tunnel-group xxxxxxxx-sc
address sc-pool pool
Group Policy - by default-xxxxxxxx-sc
tunnel-group xxxxxxxx-sc ipsec-attributes
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
call-home service
anonymous reporting remote call
call-home
contact-email-addr [email protected] / * /
Profile of CiscoTAC-1
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:5c1c99b09fb26fcc36a8bf7206af8e02
: end
Hello
Try adding the following commands
permit same-security-traffic intra-interface
NAT (outside) 1 192.168.1.96 255.255.255.240
Is there are always problems with VPN then I would maybe change VPN pool to anything other than something that comes into conflict with the LAN.
In this case, these configurations should do the trick
In order from top to bottom, they would do the following things
- First remove the pool VPN and VPN configurations
- Then remove the VPN pool
- Remake of the VPN Pool with different network
- Reattach the VPN pool for VPN configurations
- Configure NAT0 to the new cluster of VPN
- Remove the old line of the ACL of the configuration of NAT0
attributes global-tunnel-group xxxxxxxx-sc
no address-sc-swimming pool
no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0
IP local pool sc-192.168.2.10 - 192.168.2.254 mask 255.255.255.0
attributes global-tunnel-group xxxxxxxx-sc
address sc-pool pool
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
no access list inside_nat0_outbound extended permits all ip 192.168.1.96 255.255.255.240
Of course you also have the NAT configuration for VPN pools new Internet traffic
NAT (outside) 1 192.168.2.0 255.255.255.0
Please rate if the information has been useful if this resolved the issue as mark responded.
-Jouni
-
The user cannot access the web analytics
I can't a user unable to access the web tests. When the user attempts to log in they get an error box will appear with "an error occurred during initialization of the boot options.
I heard that this may be because of outdated java, so the machine has been updated, but the problem persists.
any ideas guys?
Thank you very much
RussellThis problem occurs mainly due to user 'null '.
You can try the following:
1. service and return the available to the user.
2 delete and re-create the user.
3. ensure that the user is able to connect to the workspace. -
XP tells me high when I opened a shortcut of the exe from my office. (PC-1)
The shortcut points to an exe file that is located on another pc xp on my peer-to-peer network. (PC-2)
Other PCs on the same network work very well do the same thing. In my research on it, I think it has something to do with me changing the name of PC - 1, after that I created the shortcut. (the shortcut works prior name change) Recreate the shortcut is not do me everything right.
Unfortunately I do not have restore points to return and I have no restore for this PC no more disks.Help! What can I do?
Hi yellow Jeeper,
Would you happen to use Internet Explorer 7?
Please take a look at this article about your mistake with a possible correction, applications of network share Installation generates an error: 'Windows cannot access the specified device, file, or path'.
I hope this helps!
-
Update XP Sp2 to Sp3. cannot access the web page update
The page cannot be displayed The page you are looking for is currently unavailable. The Web site may be experiencing technical difficulties, or you may need to adjust your browser settings. Please, try the following:
- Click the Refresh button, or try again later.
- If you typed the page address in the address bar, make sure that it is spelled correctly.
- To check your connection settings, click the Tools menu and then click Internet Options. On the connections tab, click settings. The settings should match those provided by your local area network (LAN) administrator or Internet (ISP) services provider.
- See if your Internet connection settings are detected. You can configure Microsoft Windows to examine your network and automatically detect network connection settings (if your network administrator has enabled this setting).
- Click on the Tools menu, and then clickInternet Options.
- In the connections tab, click LAN settings.
- Select automatically detect settings, and then clickOK.
- Some sites require 128-bit connection security. Click on the menuhelp and click About Internet Explorer to determine what you have installed the security force.
- If you are trying to reach a secure site, make sure that your security settings can support. Click on theTools menu, and then click Internet Options. On the Advanced tab, scroll to the Security section and check settings for SSL 2.0, SSL 3.0, TLS 1.0, PCT 1.0.
- Click the back button to try another link.
Cannot find server or DNS error
Internet ExplorerI can access other web pages OK.
Burty,
See... http://support.microsoft.com/kb/265847 this article has been written about products for which microsoft no longer offers support. Accordingly, this article is offered "as what ' and longerbe not updated
-
I have Windows Vista, IE 8 and labtop HP Pavilion. I had just recently Cricket Wireless Broadband, with a USB wireless modem. I now have the Charter/Comcast broadband through my cable. The modem is connected to my PC via the Ethernet port. On the connection icon on the toolbar on the right down, it shows that I am connected. The "Local Area Connection Status" in the network and sharing Center seems to be connected, since bytes are sent and received.
However, when I'm on IE8, it acts as if there is no connection. Not being able to view the web page. Also, now when I go to a local WiFi hotspot, I can't connect to a network, just as I always, and it shows that there is a link, however, it won't let me access the internet. It used to work, before everything first, I connected the cable modem.
Any ideas? Thank you!!
JFerguson15,
If the Cricket connection works correctly but your cable connection is not, which suggests the computer is set up correctly and the problem is with the cable connection. All other systems are able to connect through the connection of the Charter? If this isn't the case, please contact Charter and see if they are able to determine the issue on their end or help you reconfigure the modem.
Cody C
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
Cannot access the Web server in the DMZ from the inside using IP global
Hi all
I hope it's a very simple question.
I'm running a PIX 515 firewall v6.3. I set up a Web server in my DMZ and use static NAT for re-branded it overall static IP address. Access from the outside of the demilitarized zone works remarkably well. I can access inside the interface Web site using the internal IP, but I can't access it from inside interface using the global IP are entrusted to him.
Is there a particular reason why this would not be allowed? My feeling was that the request would be forwarded via the external interface (as it is a global IP address) and then be bounced back by my sense of the ISP the request would come to the new external interface (as the static NAT is applied to the external interface).
However if I try and access the global IP from my inside interface, then the browser can not find the server.
can someone explain why this is so? Any information would be appreciated.
see you soon,
Wayne
---------------------------------
6.3 (3) version PIX
interface ethernet0 100full
interface ethernet1 100full
interface ethernet2 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
nameif dmz security50 ethernet2
hostname helmsdeep
domain p2h.com.sg
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
no correction protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
No fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
acl_out list access permit tcp any host 203.169.113.110 eq www
access-list 90 allow the host tcp 10.1.1.27 all
pager lines 24
debug logging in buffered memory
Outside 1500 MTU
Within 1500 MTU
MTU 1500 dmz
IP address outside pppoe setroute
IP address inside 192.168.1.1 255.255.255.0
dmz 10.1.1.1 IP address 255.255.255.0
no failover
failover timeout 0:00:00
failover poll 15
No IP failover outdoors
No IP failover inside
no failover ip address dmz
location of PDM 202.164.169.42 255.255.255.255 inside
location of PDM 202.164.169.42 255.255.255.255 dmz
location of PDM 10.1.1.26 255.255.255.255 dmz
location of PDM 10.1.1.26 255.255.255.255 outside
location of PDM 172.16.16.20 255.255.255.255 outside
location of PDM 192.168.1.222 255.255.255.255 inside
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
Global (dmz) 1 10.1.1.101 - 10.1.1.125
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
NAT (dmz) 0-list of access 90
NAT (dmz) 1 0.0.0.0 0.0.0.0 0 0
static (dmz, external) 203.169.113.110 10.1.1.27 netmask 255.255.255.255 0 0
Access-group acl_out in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.1.222 255.255.255.255 inside
enable floodguard
string fragment 1
Console timeout 0
Terminal width 80
Code v6 pix or less don't let you have traffic "back" or return flow via the same interface on which it was sent. Having also your bounce back off of an external server traffic is never a good idea, because you won't be able to distinguish which and rogue attacks by spoofing someone outside your network.
Since you are using pix 6.3 code, you may be able to outside the NAT. Add this static to your config:
static (dmz, upside down) 203.169.113.110 10.1.1.27 netmask 255.255.255.255 0 0
You may need to run a clear xlate after adding the new static statement. Note that the interfaces: it's demilitarized zone, inside inside, dmz.
I would like to know if it works.
-
Cannot access the web page of the wrt54gx router
I configured my wrt54gx as point of access by disabling the DHCP and assigning static IP address 192.168.0.6. My main router is a wrt310n. My access point works very well when it is connected with a wire to the wrt310n.
I want to reonfigure the wrt54gx to use it as a main router again. To do this, I am unable to connect to the webpage wrt54gx.
Any suggestions?
Thank you
You should be able to connect to the WRT54GX and configure it from there. If it does not, simply unplug the WRT54GX of your other router and reset to the default values by using this procedure:
To reset your router by default, follow these steps:
(1) turn off all computers, the router and the modem and disconnect from the wall.
(2) disconnect all the wires of the router.
(3) turn on the router and let it start up completely (1-2 minutes).
(4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
(5) turn the router.
(6) connect a computer cable to port 1 of the router (NOT to the internet port).
(7) turn on the router and let it start up completely (1-2 minutes).
(8) the power of the computer (if the computer has a wireless card, make sure it's off).
(9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
(10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Leave the user name blank and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen). Exit your browser.If you get this day without problem, try the Setup disk (or configure the router manually, if you prefer) and see if you can get your work and router configuration.
If you can not ' response to... ". "in step 9 above, your router is probably dead. A report with this problem
If you get a response in step 9, but cannot complete step 10, is that your router is dead or the firmware is damaged. Related to this issue.
If you need additional assistance, please indicate your ISP, the make and model of your modem, the firmware version of your router and the results of steps 9 and 10. In addition, if you receive error messages, copy them exactly, and report.
Please let me know how things turn out for you.
-
happening only on a few sites of bill payment.
Hello
1. what internet browser do you use?2. If you are using Internet Explorer which version do you have installed?If you use Internet Explorer see the methods below.Method 1.
I recommend you follow the steps listed in the article below and check.
You cannot connect to or connect to Web sites in Internet Explorer secure
http://support.Microsoft.com/kb/813444
Method 2.
If the problem persists, add sites to the trusted Web site and check. Refer to the article below for the procedure.
Security zones: adding or removing websites
http://Windows.Microsoft.com/en-us/Windows7/security-zones-adding-or-removing-websites
I hope this helps.Thank you, and in what concerns:
Shekhar S - Microsoft technical support.Visit our Microsoft answers feedback Forum and let us know what you think.
If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly. -
Cannot access the Web http sites
Since yesterday, I have not been able to access any site that begins with http://, only Web sites that begin with https://. I do not download anything anything beforehand, it was working fine in the morning, but I came home in the afternoon and it did not work. No one else has used the computer. I can't go to these Web sites on firefox, safari or google chrome. I tried to unplug my router, clear the cache, history and cookies from my browser, resetting the computer, update the computer and the browser, use OpenDNS, but nothing works. I installed HTTPS Everywhere, that allows me to go on a site that wouldn't work before, but most of the websites that I use usually will not work.
I'm lost for what to do, so any help would be appreciated.
/ System Preferences / network / advanced / proxies / then deselect "proxy web http.
-
HP ENVY 750-170se: cannot access the RAID configuration via Ctrl + i on startup
I activated the RAID in BIOS > Storage Options > SATA emulations.
There are 2 drives HARD correspondents attached to the SATA 2 ports & 3.
At startup the Intel Rapid Storage screen shows the two discs. It shows the prompt to hit "Ctrl + I" to enter setup.
However: when I hit, stand or mash Ctrl + I, before, during and after the screen from the IRS, it never penetrates RAID installation.
What keeps me to enter RAID configuration menu?
Is there some SATA ports I need the HARD drive to be attached to the?
Motherboard is the model 2B4B, verson A0.11 BIOS
Based on this post I tried to use Intel Rapid Storage to make the RAID. TSRI was not installed/available in Windows so I donwloaded it... during the installation I was told there was a newer version already installed (which is weird because I couldn't access it).
TSRI in Windows made the RAID volume. No need to enter during POST/boot.
-
cannot access the web site driver for fingerprint sensor driver sp52354.exe
Re HP model dv7-4280us, Win 7 Home Premium. Caan can't discover fingerprint sensor. I can't download thedriver-ACCESS web site.
Hello
You can download directly from the following link:
http://ftp.HP.com/pub/SoftPaq/sp52001-52500/sp52354.exe
Kind regards.
-
Cannot access the Web site 'one' only. I built it, no sense
For some reason I can't access one of my client's Web sites. I can communicate with everything and all other Web sites that I own or manage. I have a new install of Windows 7 Pro SP1 OEM. It makes no sense at all. I can update the site using my software and download it via their server, but may not display the changes. Their server 1 and 1 says it's my PC. I NEVER encountered this in 12 years on any of my PCS 8 different. Any help would be greatly appreciated.
Hello
The question you have posted is better suited for the MSDN forums. Please report the issue in the following link and check:
http://social.msdn.Microsoft.com/forums/en-us/iewebdevelopment/threads
I hope that helps!
Maybe you are looking for
-
Satellite L305D fails to recover with recovery disks
It gets to the point where I guess it's almost over... It's the first time I had to recover my computer, but I had to replace the hard drive that is entered into the computer once already by Toshiba. But in the end he comes up with the ERROR: 10-FA12
-
I need help with this problem to update my windows
-
I recently took a class of Microsoft and received the "Welcome" e-mail, but could not connect with the supplied credentials (example below): Your MC ID: xxxxxxx Your temporary access code: 18995EBE-BDAF-4883-8F95-64D18D261848 I created a new account
-
I can't activate my Dell Wireless NETWORK card.
It says it is disabled and that I have to press a switch, but I can't find any switch on my computer. It is an internal card and my laptop only 1.5 years. However, I have no support from dell more via internet or e-mail and I'm in Israel for 2 mont
-
OnPlus Agent connected to 802. 1 q Trunk
Hello, team OnPlus, I posted a question a few days ago regarding an OnPlus agent unable to see miltiple VLAN. I've been advised to re-set to the switch port that the agent was connected to a trunk link, but when I tried this the agent subsequently l