Cannot boot from the HARD drive in AHCI on Satellite C mode

Similar Questions

• (Redirected) Cannot boot from the HARD drive on dell n5010 with SSD and HARD drive installed

  I have my old dell n5010 (15R Inspiron) with SSD (Samsung EVO 840 120 G) installed on the main drive Bay and the HDD (Samsung HJJ 500 G) on the optical drive Bay.

  It is a typical way to add an SSD on such an old laptop (bought from dell.com.cn in 2011).

  My Windows 10 operating system has been installed on the SSD using Samsung Data Migration software, so the previous C drive was pointless. So I formatted and installed an operating system Ubuntu 14.04 on it, hoping the grub OSs double beginning located on the HARD disk.

  However, I find no the Dell bios boot option to boot from the HARD drive installed in my optical drive Bay. All the choices are 'Hard Drive', 'Network' and 'Diagnostic '.

  But I was definitely sure that my bios program has detected the SSD and HDD with information on the main menu of the bios.

  And the LED on the optical drive Bay was immediately once I pressed the Start button on my laptop.

  As a general rule, all things were right except for options of the bios boot.

  Is there a way I can boot from HDD (with installed Ubuntu) while remaining has my SSD on the main drive Bay? I don't want to swap their positions, because the SSD is super fast on the main drive Bay.

  I have alse won't migrate 10 Windows to the HARD drive and reinstall Ubuntu on the SSD, because I'd like my windows be loaded quickly.

  Someone at - it the same problem with me?

  Any suggestion is appreciated!

  As you have a laptop, better make this laptop in the computer Forum post here:

  http://en.community.Dell.com/support-forums/laptop/default.aspx

  Bev.

• HP Pavilion 500-210 QE cannot boot from any hard drive.

  Good evening. As you can see on the subject, my computer just cannot boot from any hard disk that I put on it. I tried swapping the power supply, SATA cable, reset the BIOS, allowing the start legacy, changing to AHCI to IDE and RAID...

  When I get to the BIOS Setup, I see the hard drive and its features, but it will not start or show when I am trying to install a new OS. I'm not an expert, but I think that the problem could be in the motherboard SATA ports, but I'm not sure. Just to be sure, I tried another harddrive and it did not work as well.

  I was also thinking to buy a HDD external and installation of my OS on it, but I don't even know if it is possible and I would really like to have my computer working again.

  Thank you for your attention!

  Ok. That doesn't say that it is very likely that the motherboard has problems.

  Contact HP for warranty repair.

• Satellite L10-144 - cannot boot from a hard drive

  Hello.

  Sorry for my English because I'm french. I have a problem with a tip on this computer. I installed windows xp on my hard drive, but the computer does not start on that hard drive. If I want to boot to the hard drive I have to press F12 and select the hard disk and after loading windows.
  In the bios the hard drive is first but the hard drive does not start automatically.

  Can you help me please?

  Thank you very much.

  Hi Demilego,

  Really strange what s... Normally, the computer should boot from the HARD disk automatically.

  In your case I check the BIOS and load the default settings.
  It work?

• Z575 will not boot from the hard drive or restore DVD

  Need help on a laptop Z575 age of 2 years that immediately after an automatic update of windows, will not start either from the hard disk or restore DVDs (blue screen). Does not start in safe mode, not booting from a rescue of third party DVD. Attempt to start, it will show you the ability to start the Startup Repair tool. Repair shows that it is unable to fix with the detail following problem error messages:
  Signature of the problem 1: 6.1.7600.16385
  Signature of problem 2: 6.1.7600.16385
  Signature of the problem 3: unknown
  Signature of the 4:21200196 problem
  Signature problem 5: auto failover
  Signature of the problem 6:7
  Signature of the 7 problem: bad driver
  OS version: 6.1.7601.2.1.0.256.1

  Normally think that the hard drive has failed or that windows update caused a software problem, but the inability to boot from any restore disk that makes me think that there is another serious problem with the hardware of the laptop.

  Any help would be appreciated. THX

  Additional note: when you try to boot from a restore disc, blue screen, error message:
  Stop: 0x0000007B (0xF78DA640, 0xC0000034, 0x00000000, 0x00000000)
  It is a hardware failure that cannot be restarted soft.

  I also removed the hard drive and RAM, reinstalled and rebooted, no change.

  Additional note: I was able to access the hard drive with a recovery of old program, focused on the (SpaceFM) ram charged through the DVD player. Hard drive data appears intact. Still does not start from the hard disk or a DVD of windows system.

  Thank you. Rather than buying a 4 GB or more large key USB comes from put this into hard drive replacement. Installed correctly, boots very well now. No other error of the optical drive... and no explanation I can see, but that's it.

  Unless something else pops up we'll just call cela a HARD drive failed after 2 years of common use. Thanks again.

• 8000 elite: try to boot from the hard drive

  After placing a ssd, I get this notification. nothing else happens.

  I checked the bios, but I noticed that I can not change the boot sequence (ssd hard drive first, the other second place) so I changed the sata cables too the ssd is the startup disk.

  someone who can help?

  the ssd already has an operating system installed

  Sorry, from your description, I thought you might have "migrated" Win10 from the HARD disk to the SDS, and when people do this by copying partitions, they almost always forget migrate partition, including the bootloader files.

  So you did a clean install of Win10 for the SSD?

  If this is the case, you might be able to fix it by running the win10 installation media startup repair.

  To do this, you will need to use the link to the installation media to download Win10 and burn a DVD or create a USB key: http://windows.microsoft.com/en-us/windows-10/media-creation-tool-install?ocid=ms_wol_win10
  
  Note that when you download and build install media, the default tool corresponding to what is already installed on your PC (as in home for the House, and 64-bit to 64 - bit).  While you CAN change these settings, are NOT.  If you do, the media that results will be different and will force you to enter a NEW product code.

  Then, follow these instructions to run the Startup Repair tool: Doing - Startup Repair

  You may need to do this same series of steps three times.

  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• Portege R100 boots from the HARD drive - lack of operating system

  Hello

  I have a Portege R100 which won't the HD boot, I get the message "missing operating system".
  I don't have a compatible CD or floppy, I just about 1.8 inches for the hd, it works and I also have norton ghost 2003 is installed in another computer (a toshiba satellite A45).

  I tried to recover the drive with the help of norton and the image of the Ghost in the recovery CD, but it keep asking for a password.

  I would like to know if there is a way to use the restore with norton CD and usb driver and password screen (or where I can get the password?).

  Thank you!

  What password do you mean?

  and what recovery CD do you use? The image on the Toshiba Recovery CD is locked and cannot be extracted.

  It turns out that you cannot start or install the OS on the USB key!
  You must boot from the CD/DVD compatible player that can be connected to the PC card slot.

• can not boot from the hard drive

  On an iMac 21.5 ", OS 10.10.5 Yosemite:

  Deleted and a 500 GB external hard drive well prepared for use as a bootable hard drive. Installed OS 10.10.4 Download Yosemite on the Apple Store. When you select it as the drive hard start, it only offers itself as a restore for Time Machine option. Cannot start it up like a normal hard drive for other purposes. You want to use as a test drive for the software.

  During the installation of Yosemite, the installation by a loop repeatedly to infinity in 24 minutes each iteration to complete. I finally chose to leave the Setup process.

  What is going on?

  Have you created a USB Installer to install Yosemite? Or, have you tried to install after it finished downloading?

  Create an installer for OS X - Apple support bootable

• Satellite L505-13U and "quick start" - boot from the hard drive bbs appears

  Hello

  I just bought this laptop
  When I changed the startup on "quick start" method
  now the laptop will not boot
  I have the stack screen see just "bbs-hard disk... boot. »
  I can't enter to the bios f12 f2 does not work
  tried the keyboard and remove the hard disk without result

  Someone help me please

  Hello

  Read this thread, the Andrusito guy explained how he has disabled it:

  http://forums.computers.Toshiba-Europe.com/forums/message.jspa?MessageID=208999#208999

• Satellite M45: Cannot boot from the CD-ROM or HARD drive

  I get the following messages...

  WHEN BOOTING FROM HDD: "Invalid partition table".

  At the START of the CD: "No Bootable CD in ATAPI CD-ROM.
  By so, even though I have the recovery CD and the computer can not read them.

  I tried to change the order of boot without result. Created a bootable CD Bart, who works in my other computer, but not in this laptop. Are there special drivers, I need for this CD?
  I'm out on this one.

  Thank you

  Hello

  I think that your partition on the HARD disk is damaged and so you cannot boot from the HARD drive.
  In this case, the HARD drive must be formatted completely and then you could try to install the OS.

  It seems also that your drive cannot recognize the CD bootable (WinXP?) and, therefore, it of not possible to boot from the drive.
  Well, it really stupid s :_| situation really stupid!

  However, did you try to boot from another CD? For example Microsoft Windows original CD?
  If not I recommend you to do and eventually the reader will be able to read the CD.
  If this isn't the case, so I think that the reader must be checked. Possibly it also corrupted s.

• Boot from the 2nd drive HARD modular bay adapter (satellite P20)

  Hello

  I have a SP20-102 and I replaced the stock model with a 120 GB Seagate HDD and moved the original disc in a Module Bay HDD adapter.

  Is it possible to configure things so I can choose which HARD drive to boot from at the start, i.e. it is by default on the internal HARD drive but I can't choose to boot from the HARD drive in the modular Bay?

  I tried pressing F12 to boot device selection screen, but am unable to choose the 2nd HARD drive.

  Any ideas?

  R.

  Hello Robin

  As far as I know that it is not possible to boot from the external HARD drive. It is not supported.

  Good bye

• Satellite Pro A120 - cannot boot from CD/DVD drive

  I have a Toshiba Satellite Pro A120 of friends, he was running very slow so I said I'd do the usual for him.
  Back up all his documents, and then reinstall windows. not so easy!

  First of all, try to boot from the CD so I can boot into Ubuntu or reinstall windows.
  Me has taken long enough to work, I had to press DEL/ESC to enter in the BIOS, but once I put to boot from the CD (and was a bootable CD in the drive), it kept just boot from the HARD drive.

  From time to time I get an error saying + "Media test failure - check cable" + or something similar, theres a lot on internet on this subject.
  I think its something to do if the boot order has CD first, then it has LAN as 2nd.

  Able to boot Ubuntu from a USB key.
  Try to copy its documents on my external drive but really copying REALLY slow (like 1 MB/s) and kept getting IO errors on some files.
  I can't run diagnostic software for HARD drive that I can not boot from the CD (could get the Ultimate Boot CD on a USB but if anyone thinks it would help?).

  In windows, the CD player only reads real CD (audio similar DVD, not CDR and DVDR).
  This means a failing drive?
  What intrigues me most, however, is that I changed the portable CD player with a CD of work of another computer and windows recognize today this new CD player at all!

  By putting a bootable CD in this new CD player, it always starts from the HARD drive (do not recognize CD player in all).
  The BIOS is a bit unnecessary and does not show the detected disks...

  Also, boot Ubuntu from a USB key, with the original CD player, he reads real CD and DVD copied of all zeros are considered blank discs and replace the CD drive with a known working in Ubuntu means its not recognized at all (if this isn't windows driver problems).

  When I started messing around with it I remember windows say the time had been reset, so I set the time properly, then he did the same thing again I think. A flat CMOS battery could not be responsible for this?

  Is the motherboard and specifically the IDE controller or a broken ports, or am I doing something stupid? I'm tempted to just install Ubuntu by USB and tell him not to bother with CD more ;^)

  Any suggestions or comments would be much appreciated!

  Thank you
  Dan Gent

  > Me has taken long enough to work, I had to press DEL/ESC to enter in the BIOS, but once I put to boot from the CD (and was a bootable CD in the drive), it kept just boot from the HARD drive.
  You see the CD/DVD drive in BIOS? I mean all the details like the name WEIRD etc.
  If this isn't the case, then it means that your CD/DVD drive is not recognized by the BIOS due to a hardware problem.

  If you can see the STRANGE in the BIOS but are still not able to boot from any disk, then I suppose that the CD/DVD drive cannot read the disk for different reasons.
  One of the reasons could be a defective or damage the laser lens

  > Every so often, I would get an error saying "Media test failure - check cable" or something similar, theres a lot on internet on this subject. I think its something to do if the boot order has CD first, then it has LAN as 2nd.

  Yes, this error means that your laptop tried to boot from LAN

  > In windows, the CD player only reads real CD (audio similar DVD, not CDR and DVDR). This means a failing drive?

  As I said above, it would be possible that the reader s laser lens malfunctions and, therefore, the ODD can't handle the media. It seems that the laser lens can not calibrate properly and can not move in the correct position. This question is not repairable and the drive needs to be replaced.

  > What intrigues me most, however, is that I changed the CD drive with a CD of work of another laptop and windows don't recognize this new CD player at all!

  The fact is that not all CD/DVD drives are compatible due to different master/slave/C-salt settings. You must use the supported players! In most cases, you can find a list in your user manual what CD/DVD readers are compatible.

• XP does not start from the hard drive

  I have an old pc under win xp. It does not drive start hard when it starts. I always have a cd/dvd in master dvd for it to start windows players. Can anyone help?

  herikhi

  Hi herikhi,
   
  Change the start of the base system (Input Output) BIOS setting to boot from the hard drive.
   
  Consult the manual of the manufacturer, to do the same thing.
   

  NOTE: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from configuration can resolved BIOS/CMOS settings. Changes to settings are at your own risk.

• Satellite M30X-165 only boot from a hard drive possible

  Today, I tried to upgrade from Windows XP to Windows 7 but no media like CD/DVD bootable and works of disk removable (USB key).

  Notepad only boots from hard drive.
  With F12 I have a start menu, but no matter what I select that does not work and Windows XP boots from the hard drive. Later, I changed the boot sequence in the bios, but it does not work.

  Finally, I did a bios update 1.60 zu 2.00 but I still have the problem.
  How can I boot from DVD or USB stick?

  Try please enter the BIOS and set it to default settings. After doing this, try again please.
  Optical disc drive recognized and listed correctly in the BIOS settings?
  It works when you use it in Windows?

  Also try another thing. Put the bootable disc in ODD and shut down your laptop. Reboot and press the C key several times. If I m remembering well this should force ODD as first bootabe.

• Boot from the DVD drive on a compaq evo N610C

  Hello everyone, I try to start my computer from the CD/DVD with success.

  I use a win98 boot CD, is this OK? Or do I need another type of boot cd?

  I checked the CD on other computers, and there it works fine.

  Hoping for help

  P.S. This thread was moved from the business PCs - Compaq, Elite, Pro for PC - portable Omnibooks, EVO. -Forum moderator hp

  WL37 wrote:
  

  It's one of the problems, the bios, the parameter does not have the ability to boot from the CD/DVD.

  There are only three choices:

  start from laptop, multibay

  boot from the hard drive to laptop or computer ethernet startup.

  I also have uppdated the bios, but nothing changes.

  'Notebook multibay shoes' should work - the CD is installed in the multi-baies slot.