Cannot change the pagefile

I have a netbook no hard drive, only a 8 GB SSD (as drive C). Windows XP Home Edition takes over 4 GB and programs installed about 2 GB.  There is very little space left after that Windows allocates a 1.5 GB pagefile.

However, it also has a 8 GB SD card that Windows recognizes as drive D.  I tried to create a swap file on D and disable the pagefile on C.  No matter what I change in the virtual memory settings, Windows continues to affect a 1517 MB pagefile on the C drive (even when the value "No paging file") and will not establish a pagefile on the D drive.

I see that this, there are many cases that reported on various internet forums, but no solutions other than to reinstall Windows, that I also tried, without success.  Has anyone found the underlying cause of this problem?
I am able to temporarily remove the pagefile on C by using a freeware utility called "Unlocker" (http://download.cnet.com/Unlocker/3000-2248_4-10493998.html), however, Windows detects a page fault, reboots, immediately and recreates the pagefile.sys on C (initially at a smaller size, but eventually it widens again to 1517 MB).
Relevant suggestions would be appreciated.

You are unable to place a file on a removable drive.

Try Ctrl + Alt + Delete, select Task Manager, and then click the performance tab. Under Commit Charge, which is the Total, limit, and the pic?

You can create more free space in C in carrying one of the measures suggested below.

The default allocation for the restoration of the system is 12% on your C partition is more generous. I have them would be reduced by 700 MB. Make my computer right click on your icon, and select System Restore. Place the cursor on your C drive select settings but this time find the slider and drag it to the left until it shows 700 MB and output. When you get to the settings screen, click on apply and OK and leave.

A flaw that might be useless which is for temporary internet files, especially if you keep no copies on the disk offline. Setting the default value is 3% of the walk. Depending on your attitude to copies offline, you could bring it to 1% or 2%. In Internet Explorer, select Tools, Internet Options, general, temporary Internet files, settings to make the change. At the same time, look at the number of days, the story stands.

The default allocation for the basket is 10% of the disk. Change to 5%, which should be enough. In Windows Explorer hover over your Recycle Bin, right click and select Properties, Global and move the slider from 10% to 5%. However, try to let you become so complete that if it is complete and you delete a file by mistake it will bypass the Recycle Bin and have gone forever.

If your drive is formatted as NTFS another potential gain arises with your operating system on your C drive. In the Windows directory of your C partition you will some uninstall files in your Windows folder in general: $NtServicePackUninstall$ and $NtUninstallKB282010$ etc. These files can be compressed or not compressed. If compressed text the name of the folder appears in blue. If these files are not compressed you can compress. Right-click on each folder and select Properties, general, advanced, and check the box before you compress contents to save disk space. On the general tab, you can see the winning amount by deducting the size on disk size. File compression is only an option on an NTFS formatted disk partition / partition.

Tags: Windows

Similar Questions

  • Cannot change the incoming mail server. no text highlight

    I am unable to send mail from my Mac.  No problem with iphone or iPad. Cannot change incoming mail server as text is not highlighted.  Cannot change the server for outgoing (SMTP) mail. Cannot change the list of SMTP servers. Says offline.

    Hi Granny Smith 1.

    Thank you for using communities Support from Apple. Sorry to hear that you are having problems with mail. It's a little bit clear exactly what you see when you say that you cannot change any server info, but if you continue to have problems sending or receiving mail, you will find the troubleshooting steps in the following article useful:

    If you cannot send or receive e-mail on your Mac - Apple Support

    Kind regards.

  • Cannot change the Apple ID

    I'm changing my Apple ID, but when I try to change ID, it does not show the ability to 'change e-mail address '.  How can I get that option?

    You cannot change the name of the device.

    Sign of your ID, then click on my Apple ID and change the ID (you can not change if it's an address to iCloud)

  • Good for laptop - cannot change the ISP; keep returning to a previous provider

    Windows 7 laptop of my grandson, I'm migrating FIREFOX (excellent resource!) of my aging XP desktop. An existing Mozilla installation on the guarded device tries to connect to an ISP in Sydney (1000km) which kept out, I guess because the signal is too weak. Too far - on the Internet?

    Reinstalled my new ISP contact, reinstalled a fresh copy of Firefox, copied the old profile XP (just underneath the random string file name), but cannot change the fault. Firefox at startup tries to raise the old ISP (Sydney) and expires, and then allowing me to establish a manual connect with the ISP (my current) new.
    Perhaps a clue: in my Firefox troubleshooting info, change preferences, the browser start page is the address of 'old', with 'override mstone' ignore, what look like prints of registry entries, but I can't change all that - and maybe it's wise! An annoying secondary question: on arrival, the laptop listed no administrator user. So I am me came as an administrator, but I wonder if a past or current even Admin hidden could register (or other) entered resistant to change.

    Late discovery: the laptop is apparently infected with browser pirate btsearch.name. Search Google throws a series of removal procedures, and I'm now working through them.
    What Miss me?

    Sometimes a problem with Firefox can be a result of malware installed on your computer, you may not be aware of.

    You can try these free programs to search for malicious software that work with your existing anti-virus software:

    Microsoft Security Essentials is a good permanent antivirus for Windows 7/Vista/XP, if you do not already have one.

    More information can be found in the article troubleshooting Firefox problems caused by malware .

    This solve your problems? Please report to us!

  • change my phone number and cannot change the keychain

    Dear,

    gently, I changed my phone number and cannot change the keychain

    You try to make the change in the preferences/iCloud/Keychain/Options of the system? What happens when you try?

    City link below.

    • The device that uses the SMS compatible phone number you provided when you set up first iCloud keychain. A verification code is sent by SMS to the phone number. If you can not access this number, Contact the Support of Apple, which can verify your identity so that you can run the installer on your new device.

    Frequently asked questions about iCloud Keychain - Apple Support

  • Cannot change the Google search bar

    In Safari, I go to Google.com and do a google search. So far so good.

    Now, on the search results page, I try to edit the search in the Google search bar and nothing happens - the Google search bar is totally insensitive. To do another search, I use the address bar in Safari or reload google.com.

    I have deleted history, deleted all the data of the Web site, disconnected plugins and extensions, deleted the cache via the menu Developer. I used 3 CleanMyMac to clear and reset everything.  I can't solve the problem.

    Safari 9.0.2 (11601.3.9)

    OS X El Capitan 10.11.2

    Mac Mini (late 2014)

    A

    Please see below:

    Cannot change the Google search criteria in Safari

    B

    'CleanMyMac' is a scam and a frequent cause of instability and poor performance. Depending on which version you have, the developer's instructions may not completely uninstall. Please follow these instructions, then do as below.

    Please, back up all data before proceeding.

    Triple-click anywhere in the line below on this page to select this option:

    /Library/LaunchDaemons/com.macpaw.CleanMyMac2.Agent.plist

    Right-click or Ctrl-click on the highlighted line and select

    Services ▹ reveal in Finder (or just to reveal)

    the contextual menu.*, a file can open with a selected item. If so, move the selected item to the trash. You may be prompted for administrator login password.

    Repeat with this line:

    /Library/PrivilegedHelperTools/com.macpaw.CleanMyMac2.Agent

    Restart the computer and empty the trash.

    You may also delete one or more of these elements in the same way:

    ~/Library/LaunchAgents/com.macpaw.CleanMyMac.helperTool.plist
    ~/Library/LaunchAgents/com.macpaw.CleanMyMac.volumeWatcher.plist
    ~/Library/LaunchAgents/com.macpaw.CleanMyMac3.Scheduler.plist

    Never install "CleanMyMac" or something like that.

    * If you do not see the item context menu copy the selected text in the Clipboard by pressing Control-C key combination. In the Finder, select

    Go ▹ go to the folder...

    from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

  • USB 6009 CANNOT CHANGE THE CONFIGURATION OF TERMINAL TO CSR... Can't SEE not the OPTION configure when right-click on the device...

    USB 6009 CANNOT CHANGE THE CONFIGURATION OF TERMINAL TO CSR... Can't SEE not the OPTION configure when right-click on the device...

    Once again... Thanks for the tips...

  • I signed on XP Pro SP3 as an administrator but you cannot change the timing of Windows Update to 03:00. All options are not enabled. How can I change the time, updates are made? __

    I signed on XP Pro SP3 as an administrator but you cannot change the timing of Windows Update to 03:00.  All options are not enabled.  How can I change the time that updates are made?

    Hi imoffshore,

     

    Welcome to Microsoft Answers Forums.

    We would like to get some more information from you to help solve your problem. You better, please answer the following questions.

    ·         When was the last time it worked?

    ·         Remember to make changes to the computer recently?

    ·         You have security software installed on the computer?

    ·         You get the error message?

    When you open the tab automatic updates in the control panel or My Computer property sheet, all options of configuration of the automatic updates may be grayed out. This happens due to one of the following reasons:

    1. You are not logged as administrator (or equivalent)
    2. Strategy of automatic updates is enabled
    3. Automatic updates (and Windows Update) access is blocked by group policy

    The options available for automatic updates.

    You must make some changes in the windows registry.

    Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

    How to back up and restore the registry in Windows

    http://support.Microsoft.com/kb/322756

    • Click Start, run and type REGEDIT to . EXE
    • Go to this location:

    HKEY_LOCAL_MACHINE-SOFTWARE-policies-Microsoft-Windows------WindowsUpdate------AU

    • In the right pane, delete the two values AUOptions and NoAutoUpdate
    • Go to this location:

    HKEY_CURRENT_USER-SOFTWARE-Microsoft-Windows-CurrentVersion------policies------WindowsUpdate

    • In the right pane, delete the DisableWindowsUpdateAccess value

    Using the Group Policy Editor - for Windows XP Professional

    • Click Start, run and type gpedit.msc
    • Navigate to the following location:

    => Configuration of the computer
    ==> Administrative templates
    ===> Windows components
    ===> Windows Update

    • In the right pane, double-click Configure automatic updates and set it to not configured
    • Next, go to this location:

    => User configuration
    ==> Administrative templates
    ===> Windows components
    ===> Windows Update

    • In the right pane, set to remove access to all Windows Update features on not configured

    Change how Windows installs or notifies you of updates

    http://Windows.Microsoft.com/en-us/Windows-Vista/change-how-Windows-installs-or-notifies-you-about-updates

    Halima S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • You cannot change the format of the cursor

    Original title: mouse cursor

    Cannot change the format of the cursor; message says no file found - for example, C:\WINDOWS\Cursors\arrow\_rl.cur

    _rl.cur is not a slider that comes with XP. Nor is the folder named arrow. You must have installed a 3rd slider party system and I guess you are trying to change that.
    Try to reinstall it.

  • Error: Windows cannot change the password when attempt to set a password to connect to the Windows XP computer.

    Original title: Windows cannot change the password.

    I'm trying to set a password on my computer with windows xp professional and everytime I try, I get a message saying: Windows cannot change the password. Please can someone help me.

    With our thanks

    Elizabeth

    Hi Elizabeth,.

    You can follow this link & check if the problem persists:

    Impossible to change the password for the administrator account in user accounts in Control Panel

    Hope the helps of information.

  • Cannot change the font color on the desktop icons

    I am running windows vista. I can't change the font as in windows xp. No matter if the background is dark or the police is always black... Help!

    Hello

    Thanks for posting the question in Microsoft Answers.

    I apologise for the inconvenience.

    Unfortunately, you cannot change the font color of desktop.

    Because desktop wallpaper images have different colors, it is easy for the colors of unreadable fonts if they are on top of the same color in a background image to display. For example, a black font on top a dark part of the background image or a white font on a white part of a background image.

    The desktop icon fonts are dynamic and show white on dark background and change in white with a shadow effect black on a light background.

    In previous versions of Windows, it did not matter what color you chose to fund policies, some would still make invisible because of the background color of a desktop wallpaper. The user was constantly moving icons around the desktop computer to another colorful area where the police could be read. This was the source of a large number of complaints from users asking for a policy that was still visible, regardless of the color that was behind the police.

    However, you can change the theme and see if that helps:

    Change desktop theme:

    http://Windows.Microsoft.com/en-us/Windows-Vista/change-desktop-theme

    Hope this information helps. Let us know if you need additional assistance. We are happy to help you.

  • Cannot change the Vista hosts file

    I started Notepad as administrator and open my hosts file, made my changes, but when I try to save it I get this message: cannot create the c:\windows\system32\drivers\etc\hosts file verify that the path and the name are correct

    How to save this file? Thanks for any help!

    Hello

    The host files are linked to the internet explore and this is why it must be very careful when you change them. And this is the reason why they were safe as to change. We have a FixIT tool to assign default host files. It's here.
    http://support.Microsoft.com/kb/972034 also, here is the article that explains how to change the host files and the Lmhosts file in Windows Vista and Windows 7. You cannot change the Hosts file or the Lmhosts file in Windows Vista and Windows 7
    http://support.Microsoft.com/kb/923947

     

    I hope this information helps you!

  • Cannot change the hosts file in Windows Vista Home Premium

    Posted on behalf of a client:

    Cannot change the hosts file in Windows Vista Home Premium. Read-only value.

    Help, please.

    Hello

    I suggest you to try the steps below and check if it helps.

    Method 1: Try to take possession of the host file and check to see if the same problem happens.

    To apply permissions to a file or a folder:

    a. right click on the file or folder and then click Properties.

    b. click the Security tab and then click Edit.

    c. do one of the following:

    ·         To set permissions for a user who is not listed under group or user names, click Add, type the name of the user or group, click OK, select permissions and then click OK.

    ·         To change or remove permissions for a user or an existing group, click the name of the user or group, select the permissions and then click OK.

    For more information, see the article mentioned below:

    What to know before applying permissions to a file or a folder:

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-access-denied-when-opening-files-or-folders

    Prevent changes to a file or folder (read-only):

    http://Windows.Microsoft.com/en-us/Windows-Vista/prevent-changes-to-a-file-or-folder-read-only

    Hope this information is useful.

  • Microsoft Movie Maker - cannot change the length of each clip.

    Cannot change the length of each clip on Microsoft Movie Maker.

    I clicked on 'tools', then 'options' in Microsoft Movie Maker after importing my media and organize my clips as the way I would like it. When I then click on the "Advanced" tab, image duration shows only 5 seconds with the transition period only 1.25 seconds, which is the default setting and that is also what I want. However, when I play my project in Movie Maker, it accelerates through each clip. I also noticed that when I press the title of 'Clip' in my headings at the top left and then click on 'Properties', the duration of each clip shows that only 00:02 seconds. Which is why my speed clips too quickly.

    I would have thought that setting my time of duration in the Tools section would then set in the Clips section, but this is obniously does not. I don't understand why everyone would show differently and wonder if you can help me to slow down the speed that my movie is playing.

    Thank you

    Cannot change the length of each clip on Microsoft Movie Maker.

    I clicked on 'tools', then 'options' in Microsoft Movie Maker after importing my media and organize my clips as the way I would like it. When I then click on the "Advanced" tab, image duration shows only 5 seconds with the transition period only 1.25 seconds, which is the default setting and that is also what I want. However, when I play my project in Movie Maker, it accelerates through each clip. I also noticed that when I press the title of 'Clip' in my headings at the top left and then click on 'Properties', the duration of each clip shows that only 00:02 seconds. Which is why my speed clips too quickly.

    I would have thought that setting my time of duration in the Tools section would then set in the Clips section, but this is obniously does not. I don't understand why everyone would show differently and wonder if you can help me to slow down the speed that my movie is playing.

    Thank you

    ================================
    The change of setting to: Tools / Options /.
    Advanced... tab applies only to the added clips
    to the timeline * after * you change the setting.

    If you switch to view "Storyboard" and select
    all of the clips as a batch (select one and the type...
    CTRL + A)... you can add the 'Speed Up, Double.
    or "Slow down, half" effect of changing the
    duration. Simply select all clips / right click
    the effect on the menu... Choose...
    Add to storyboard table.

    'Speed Up, Double' cuts the duration of half.

    "Slow Down, half ' double life.

    These effects can be added up to six times.

    If you need finer adjustment...
    the info may be useful:

    You can change the duration for each clip
    manually. Move your pointer autour the
    edge of an element until you see a double red
    arrow. Now, drag the double red arrow...
    you will see if show a ToolTip displays the duration
    train to change.

    Or... just to redo the project after changing
    the long-term: Tools / Options / Advanced
    tab.
    Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

  • Cannot change the boot options. cannot depend on a windows Defender

    Cannot change the boot options. error message says "Windows Defender is disabled". cannot depend on windows Defender.

    If you use Norton, McAfee, AVG, MSE etc., they will be either disable or conflict with the Defender.

    http://social.answers.Microsoft.com/forums/en-us/vistasecurity/threads

    For questions of security program, kindly ask in the Security Forum.

    See you soon.

    Mick Murphy - Microsoft partner

Maybe you are looking for

  • TouchSmart 520 with Windows 10

    Hi all! Do you know if the PC HP Touchsmart 520 series will have drivers for Windows 10? Is because Microsoft has released a free booking for this operating system, and I would use it. Thank you!

  • iPhone cannot go on internet messages after updating iOS

    After I updated my iPhone would not send my messages and I can't go on the internet unless I am connected to WiFi. It's the only way I can use my phone on the internet it's if I am connected to WiFi. I restarted my network settings and still cannot a

  • Satellite P100-257: that means the OpenGL options

    Hello! My machine is P100-257. 945GM / GMA 950.Section 3D of the screen: OpenGL: means the first two options (sorry, but can't exactly translate to the English description full options): 1. something of "asynchronous".2. something "blit". What should

  • read the type of variable and the value of LabView

    With the help of the TS. Class sequence that I try to get the type of variable and the values of local variables, parameter, fileglobal and stationglobal. Unfortunately I'm not able to find the right function. Hope someone can help me. Kind regards L

  • Management errors in the grid lines

    I am designing a good system for a project of management errors, I'm working on, but I encountered a problem of 'design '. I thought it would be good to ask some advice here before I sit down and start creating the system of error handling. I have mo