Cannot communicate with NI-VISA and Tektronix scopes

Similar Questions

• why I got the labview error cannot communicate with EMANT300NI VISA

  I got error when trying to run my labview after connection with emant300 usb daq.the error, I had are:

  (1) NEITHER VISA driver is installed/LV needs of NI-VISA to connect with the serial comm port

  (2) conflict of Comm port during the installation of the driver emant300

  any advise how to solve this problem?

  Thank you

  
  

• My Lexmark printer stopped working and the error message says "printer cannot communicate with the computer" (from "twisted into the USB pins?).

  When my printer stopped working because of error messages about "printer cannot communicate with the computer" (from "twisted into the USB pins?), I tried to change to 2nd USB port without success. I tried a new cable; that did not help.

  Then I uninstalled and reinstalled my Lexmark printer and changed the error message. Now, the printer does not work because "the USB device is not recognized."

  I tried to update the chips; Use 1 USB port; and using the old cable, all this without success. I checked the connections of the cable to the printer and the PC and turn on the printer and goes off; I'm out of ideas. Any other suggestions?

  Hi ChristineKrause,
   

  Here are some links that might help you:

  Peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation

  Advanced troubleshooting tips for General USB for Windows XP problems

  Try the steps listed in the items mentioned above and see if that helps you solve the problem.

• BlackBerry Z10 Z10 suddenly stopped synchronization of calendar and contact - link gives BB cannot communicate with connected mssg but displays device

  I think that BB link updated the software in March 2015.  I had been very good sync with my laptop Windows 8 with the Outlook calendar and contacts, but this week it stopped.  BB link watch Z0 connected, but says cannot communicate with the device.  I tried the solution of knowledge base - leave plugged phone with a USB cable, power phone off, then back on donkey wait 3-5 minutes for the pilots to complete loading - but none help.  I rebooted the computer and the Z10 several times, but no luck with the synchronization.  Any help is appreciated!

  Try the following steps, which will completely remove all traces of BlackBerry-link device driver entries and may solve your problem:

  1. Uninstall the BlackBerry link.
  2. Open the Device Manager by pressing the Windows key + R on your keyboard type devmgmt.msc , and then click OK.
  3. Click view , and then click Show hidden devices on the menu that appears.
  4. Expand the BlackBerry section by clicking on the + symbol next to it.
  5. Right-click on the following, and then click Uninstall. In the dialog box that appears, select delete the driver for this device. If more than one of each of the following entries appear, remove them as well.
     • BlackBerry smartphone
     • BlackBerry smart phone
  6. Expand the network adapters section by clicking on the + symbol next to it.
  7. Right-click on the following, and then click Uninstall. In the dialog box that appears, select delete the driver for this device. If more than one of each of the following entries appear, remove them as well.
     • BlackBerry smartphone
     • Tethering BlackBerry smartphone
     • Virtual private network of blackBerry
  8. Restart the computer.
  9. Reinstall the latest version of BlackBerry link.
  10. Try to reconnect your BlackBerry Z10 to the computer and see if she is able to communicate with the BlackBerry link.

  After back and let us know if it works for you.

• Cannot communicate with the first DNS Server (169.126.63.1)

  Hello
  I have recently had problems with my internet connection and therefore cannot get on the internet at my place when it used very well. I have a wired connection usually, but tried to install a router but now even the wired connection doesn't work and I get the message "Cannot communicate with the first DNS Server (169.126.63.1)" I tried many things and even reformatted my hard drive, do a reinstall system, different setting reset and still it does not work. Hope someone can help me in this situation. Thanks to a bouquet.

  Here is my information

  Hello

  1. have you done any software or hardware changes to your computer recently?

  To work with this issue, I would say that you try the methods below to resolve this issue.

  Method 1:

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Method 2:

  
  Step 1:

  Let us reset TCP/IP and check.

  To reset TCP/IP stack to go to this article and follow the instructions.
  http://support.Microsoft.com/kb/299357

  Step 2.

  1 connect to your router (by typing 192.168.0.1 or 192.168.1.1 in the address bar) and connect. Check your user manual or documentation if you don't know the references of logon.
  2. make sure that you are in the installation - basic configurationcategory.
  3. scroll down until you see "DHCP Server"- if it is disabled, select 'Enable'.
  4. enable DHCPif you want, you can change the number that starts the DHCP IP setting. (This is optional)
  5. use the DNS servers provided by your ISP. There are many DNS servers out there. It is preferable to use your ISP if possible.
  6. scroll and click ' Save Settings '.

  Step 3.

  1. click Startand then clickControl Panel.
  2. go in network and sharing Centerand then click onchange adapter settings.
  3. right click on Local area connectionand selectProperties.
  4 Select Internet Protocol Version 6 , and then clickProperties.
  5. click on get automatically a DNS server address, then pressOk.
  6 select automatically an IP address to get.
  7. repeat the steps for Internet Protocol version 4 as well.

  Also visit these links:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Network adapter problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

  Hope the information is useful.

• computer cannot communicate with over 8600

  My 8600 Officejet Plus works fine on a wireless network for about a year, but after restarting the computer yesterday morning, I get the message "...". cannot communicate with the printer.  I tried all the suggestions below without result.  I can access page ews from the printer to the computer and I get my apps on the internet every night. I have Ran the network to the printer and all past test.  The Network Setup page shows the printer is connected and ready for the correct ip address.  I ran the HP print and scan doctor and you can see that everything works.  I also ran the troubleshooter in Windows and it showed no problem with 'the printer is ready.  I unplugged the router, printer and restarted Windows.  I removed the printer via the "devices and printers" window, as well as the HP software.  I reinstalled the software, connected the printer and run the wireless configuration.  I've updated the ip address on windows.  All to nothing does not.  Any help would be appreciated.

  Running Windows 7 Home Premium

  Belkin N router is

  In fact, I found the problem.  It seems to run a malicious program to the startup disable Norton anti-virus and changed several keys in the registry that prohibits the computer to communicate as well as Outlook unauthorized access to my POP3 account and who knows what.  I managed to uninstall Norton, then re - install a newer version.  This enabled Norton run a quick scan before restarting.  After re-booting, Norton has been disabled again.  I used Norton Erase to analyze and repair the registry that solved the problem.  Immediately after re-boot after the last scan and fix the network Windows Test Page that announces the printer has been installed on persistent organic pollutants.

  Thanks for you quick response, however.  I suspect a virus when I tried, without success, to open Norton in order to disable the firewall and couldn't.

• SE error message saying the printer cannot communicate with the computer cause of blocked files.

  Original title: DRIVER of PRINTER BLOCKED

  A COMMS. ERROR MESSAGE ME SAYING THAT MY PRINTER CANNOT COMMUNICATE WITH MY PC. AFTER COMPLETING THE USUAL HARDWARE CHECKS THAT I USED THE SERVICE CENTER OF DELL ONLINE THAT REMOVAL OF TWO STATES ' DLEACOMS. EXE' AND ' DLEAWBGW. EXE ' MUST BE RELEASED TO ALLOW MY PRINTER TO WORK.

  I SEE NO REFERENCE TO THESE FILES IN THE WINDOWS FIREWALL AND TO THIS DAY THE ONLY WAY AROUND THIS PROBLEM IS TO REMOVE THE PRINTER AND REINSTALL, BUT IT WORKS FOR A SHORT PERIOD. I USED (BY REMOTE CONTROL) THE STATION OF SOLUTION DELL THREE TIMES BUT EVEN THEY EVENTUALLY REMOVE ALL AND REINSTALL THE PRINTER.

  SOMEONE HAS AN IDEA HOW THESE FILES CAN BE UNLOCKED?

  I suggest to disable CAPS LOCK key since your message is all in the capital and difficult to read. Have you tried to add to the exception in the Windows Firewall? Try also to change your network connection for work or at home instead of public. Also make sure you installed the latest version of the driver and are compatible. Also try to run the tool:

  http://support.Microsoft.com/mats/printing_problems/

  If the problem is not resolved, contact Dell customer service.

• My Dell all-in-one 962 stopped printing all of a sudden. The error messages are that the computer cannot communicate with the printer.

  My Dell 962 All In One Printer suddenly stopped to print. I get an error message that the computer cannot communicate with the printer. The error message suggests that I unplug and plug back the power plug and the USB cable to the printer and make sure that there are no restrictions of firewall to the printer. I did what was suggested and still no printing. I have resinstaled the printer from the CD software, I got with the computer and also installed the latest driver using the software of the software upgrade wizard.

  and also installed the latest driver by using the Software Update Wizard software.

  That would not have been the best idea... but it is unlikely that the cause of your immediate problem.

  The next thread does not make much sense to me, but it describes a situation similar to what you described and the proposed solution is supposed to have worked.  Try it and see--> http://en.community.dell.com/support-forums/peripherals/f/3528/t/19483019

  I suspect that what really happens is that the driver has become corrupted.  In many cases, simply reinstall the driver is not fix things; you have to clean the old corrupt driver before installing the new.  Thus, it is more likely that the part "Uninstall" the related response is what is helping rather than playing with services... but go ahead and follow these directions, just in case.  In fact, I suggest that you run under first antimalware scanners before following the tips in the above link.

  If I had not found the link above, that's what I would have suggested (whichrequires that you have Windows XP):

  Often, but not always, the symptoms you describe are caused by a corrupt print job stuck in the queue or a damaged printer driver.  However before you clean things up, on general principles, that you can download, install, update and run full scans with each of these two free programs.

  MalwareBytes AntiMalware

  SUPERAntiSpyware

  Use the free version, not the free trials of "pro" versions  Pay attention during installation uncheck any prechecked boxes that would install some additional third-party programs.

  Do not run the scans at the same time.  Each scan will take a while.  Start one and go do a non-it chore.  Once the scan is finished, leave the program to deal with anything it finds.

  Once done, you can keep or uninstall programs, or both.  If you keep SAS, I suggest to change its default setting does NOT automatically when Windows starts.

  Uninstall all software from Dell to control panel > Add / Remove programs

  Download Microsoft Fixit 50126 impression: http://go.microsoft.com/?linkid=9662904

  Close all running applications (anything with an icon on the taskbar).

  Run the Fixit routine.  Note: The routine Fixit has two modes, light and complete.  It will run in full mode when you check the box "Reset the spooler to print on values."  This will remove all printers, so if you have any other printer installed, I recommend running the Fixit in full mode.  If you have other printers and you do not (necessarily) want to reinstall them, run the Fixit in light mode (box unchecked).  This may work anyway.  You must restart the computer after you run in full mode; you need not restart after the Chase mode.

  After the Fixit has executed and you have restarted if necessary, make sure that the printer is disconnected from the computer and run the installation software.  You will be asked to connect the printer to a suitable place.  You can use the CD that came with the computer or download the software here (which is relatively hard to find, the claims of the main page of the 962 product support it cannot find the drivers)--> http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=R89490

• MG6120 - cannot scan error "cannot communicate with scanner.

  Hi, I have a Mac Book Pro with OS 10.10.5 (Yosemite).  I have the Canon MG6120 printer.  Since I updated to Yosemite, I'm more able to scan using the MP Navigator ex software  I get the following error message:

  "Cannot communicate with the scanner.

  Cable may be disconnected or scanner may be turned off.

  Check the status.

  Scanner driver will be closed.

  2.1.0.

  The only way I can scan is by using the touchpad on the printer and saving the scan on a USB key.

  I went to the page support and downloaded the latest drivers, but he has not made a difference.  I need to remove the printer and re - add again?

  You will appreciate greatly any help or advice.

  Thank you very much

  Alice Berman

  Hello.

  If the printer is used via the USB port, make sure that the printer is connected directly to your computer.  Avoid using USB hubs or extension to connect devices.

  If the printer is used with wireless, please proceed as follows to save your scanner to work wireless on Mac:

  1. click on the "Canon IJ Scan Utility" icon on the top of your screen and choose "display settings." (Located near the clock, looks like a scanner open with an arrow below). For the latest operating systems, the program can be located in the Canon Utilities listing applications.

  2. in the next screen, make sure that the network version of the printer is selected instead of "do not use". The network version will be a long series of numbers next to him.

  3. click on "Scan-of-operation-panel-settings".

  4. a new window should appear, make sure that the printer is selected, and then click OK.

  5. click OK to exit the utility.

  Once done, do the following:

  1. open the Application folder.

  2. open Canon Utilities.

  3. open MP Navigator.

  4. Once opened, click on the "Settings/preferences" button at the bottom.

  5. in the menu drop-down "Product name", select the Network Scanner.

  6. click OK at the bottom.

  Once done, try to scan from MP Navigator.

  If you continue to have difficulties, find more help contact us.

• CanoScan 88ooF error report, "cannot communicate with scanner.

  When I try to use my scanner I get the error report, "cannot communicate with scanner, make sure it is plugged and truned on.» When I go into Windows Device Manager I can see it, and when I click on the buttonn properties, it says that the device is functioning properly. I downloaded the latest version of the software driver etc and I uninstalled and re installed again but I still get the same error report.

  I use Windows 7, 64-bit version.

  

  Above is I get the error message.

  After two days of fruitless efforts, I found my own solution. I downloaded and installed VueScan x 64 and it works a treat. I think that the problem I've been is due to the fact that the scanner driver is 64-bit and the programs that install are 32-bit, even if the scanner driver works perfectly fine 2 bit programs do not see.

• HP 6830: HP 6830 cannot communicate with printers

  Hello

  wehenever I send you a print through my laptop, I get a dialog box indicating that the computer cannot communicate with the printer. (It's also seems to indicate a correction option that is not fix something).

  However, the print job is done perfectly.

  It dose not happen when an an email impression is made.

  How can I get rid of this dialog box?

  Thank yoy

  Hello

  Thank you for using the HP Forums.

  Can you try using a TCP/IP port?

  Creating a TCP IP port

  1. print a Configuration Page to get the printer IPv4 address (you can also tap on the icon wireless on the front panel of your printer to obtain the IP address)
  2. on your PC, go to the Panel control, devices and printers, right-click the printer and on the left, click printer properties, select the Ports tab.
  3. click Add Port, select the Port TCP/IP Standard, then New Port and follow the instructions in the wizard.
  4. Enter the IP address of the printer.

  This video resource will show you how do:

  Create & port use TCP IP

  Note that you can ALWAYS go back to the original port the HP software installed by selecting the HP port on the Ports tab (in the properties of the printer)

  Let us know if it works

• Error message when printing - Communication not available, cannot communicate with the computer

  Original title: for some reason, my computer and printer communicate is no longer... I spent every day toubleshooting... always get this box: Communication not available, cannot communicate with the computer

  I have a Dell Inspiron E1505 laptop and Dell AIO 924 printer if that helps! all cables are correctly connected, unplugged, replugged, shut down rebooted, uninstalled / printer driver, always even reinstalled!

  uuggghhhhh!

  flustered2,

  You recently reinstall the operating system? If so, have you installed the drivers in the order?
  How to download and install drivers in the correct order

  First run delete print jobs to remove all print jobs stuck in the queue.

  Unplug the printer.

  Download and run the patch (cleaning printer utility) until it prompts you to restart your computer.

  Restart your computer.

  Now you can install the printer using the Dell Printer 924 disc.

  Link to the patch/drivers(if needed) is to...

  Dell 924 Photo-All - In - One Printer owners thread (W7)

  Don't forget the programs anti-virus and firewall will block communications.

  Also try this tweak...

  Go into Device Manager (right click on my computer, left click Properties, material of the left click, left click Device Manager)

  Go to the section USB controller, and then click the plus sign +.

  Go to each USB hub root and right-click on it, on the left, click Properties, on the left, click power management. Uncheck the allow the computer to turn off this device to save power.

  Restart your computer.

  Rick

• The Dell printer cannot communicate with the Dell computer.

  It seems that suddenly my Dell AIO 942 printer cannot communicate with my Dell Studio 17computer.  These devices have been the transparent connection until two days ago.  I've set up a restore point, I installed the drivers, unplugged and re plugged 110 s and USBs, used different ports and I still have the same, printer cannot communicate with the State of the computer.   Copy and scan functions are good, Windows Vista operating systems.  How can I find these devices to their previous state of communication?

  Jesse,

  Thank you very much for the detailed information. It really give us a head start trying to solve the problem.

  Please answer these questions to get more clarity-

  (1) what are the other steps in troubleshooting tried by you so far?

  (2) other changes on the computer that I should know about?

  In the meantime, I have you refer to items offered on the Dell website - troubleshooting

  http://www.Dell.com/support/home/us/en/19/product-support/product/Dell-942/research

  You can also have a look at the Microsoft article as well-

  http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Get back to us with the results.

• HELP: What router supports VLAN? -I wish both groups cannot communicate with each other.

  Hi all

  I have 5 wireless devices must connect to the router.

  I want to divide it into 2 groups:

  That is to say, 1, device A, B, C, group 2, device D, E.

  I would like two groups cannot communicate with each other.

  I've heard, it can be done by VLAN, is e2500 can adapt to what I need?

  What about EA3500 and EA4500?

  I use G wireless, is what it means that ea4500 is out of choice even if it supports VLAN?

  Thank you all!

  Evil

  Thanks for the clarification for the OP

  FWIW

  is this an alternative to routers that do not support of VLAN, to do what you want

  http://www.SmallNetBuilder.com/lanwan/lanwan-HOWTO/32486-how-to-segment-a-small-LAN-using-tagged-VLA...

• Windows cannot communicate with primary dns server

  Hey everybody.  I have a home network, wired PC, 1 wifi 1.  WiFi works fine.  wired network printers work well, other computers (laptops work fine both wired and wireless.)  I have a PC (VISTA), which now gives me the "windows cannot communicate with primary dns server.  This has happened a couple of times, but a reboot fixed things.  Once I had to change primary dns server from automatic to 208.67.222.222 (who got to this site), it worked.  Now, the same error, but nothing works.  I have tried in both directions between the DNS auto numbers listed here, also, have tried the following:

  ipconfig/flushdns
  ipconfig/registerdns
  netsh interface ip reset reset.log
  netsh int ip reset resetlog.txt

  and had windows try to reset the DNS of countless times.  Nothing works.  The upgrade to W7 eventually will correct this problem?  Another question, my wife insists on the use of AOL software (I know, I know), even if all that she uses to is by e-mail.  She says she loves interface.  A chance that caused this problem?

  Hello

  1. have there been recent changes to the system before the show?

  2. the problem occurs only with specific applications?

  Method 1:

  Follow the link and follow the steps proposed by Shekhar S and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/cant-communicate-with-primary-DNS-server/9043f785-2f4e-4CC1-ADF5-6ba5ca413749

  Method 2:

  Follow the link below and follow the steps. Check if it helps.

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  http://support.Microsoft.com/kb/928233

  I also suggest you to run the command in the command prompt and check where the Windows Vista computer is pointing to DNS and DHCP.

  ipconfig/all

  Post back with the results in this thread.

  Let us know if it helps.