Cannot connect the phone to the computer with usb (BSoD)

Similar Questions

• Cannot start the computer with DISPLAY of ERROR: 0 x 00000024 (0 x 00190203, 0x837C33E80, C0000102,

  last time I connect, the NTFS has been runs a check and then close my computer with a SCREEN of ERROR and the COMMAND SCREEN CHECK BONES. All the time when I used the F8 key, it has not started safe mode and all. When I used F10 and F12... He made a QUICK and FULL TEST and said my hard drive 'PASS'... but no way to start the computer. The DISPLAY of ERROR says:

  --------

  Disable or uninstall an anti-virus, backup utility disk defragmentation. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:

  Stop: 0 x 00000024 (0 x 00190203, 0x837C33E80, C0000102, 0 x)

  ------

  Help, please! as I have not set up disk or CHKDSK with me. granted access via another computer. My question is: can I download a service pack 3 or installation to start XP Professional, on a USB to do - turn off the anti-virus, backup utility, disk defragmentation?

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

  Source: http://answers.microsoft.com/en-us/windows/forum/windows_xp-system/windows-xp-startup-error-stop-0x00000024/a15138c6-4be1-483d-b6db-e9d8db853d5b

• Connect the 7610 with USB cable

  Hello

  Try connecting a HP7610 printer to my XP laptop that only has USB ports

  Is it a USB 2.0 has a cable work?

  Thank you

  JF

  Hi @hp7610,

  Welcome to the HP Forums!

  I noticed that you are trying to connect your HP Officejet 7610 to your Windows XP laptop. I'm happy to help you!

  You'll need is a USB 2.0 A to B cable, so that it works correctly with a USB connection.

  Moreover, according to the specifications of your printer, Printer Specifications for series e-all-in-one HP Officejet 7610 Grand Format (H912). You can use an Ethernet cable or a wireless connection as well.

  Hopefully this information is what you are looking for and have a good day!

• Vista goes to 50% CPU usage and connects the computer for hours after the beginning

  Original title: Vista processor

  Stupid Vista goes to 50% CPU usage and connects the computer for hours after the start.  Cannot run anything with any request of CPU without getting bogged down and crashing.  It is not windows defender, I suspend this service and the machine is ok for another 1/2 hour, them I'm up to 50% of the CPU.  The idle process said Task Manager is > 90%, still indicates 50% CPU usage and the cooling fan looks like a 747 taking off.  Should I just pull the machine and go for Linux, or what?  Cannot run games or whatever it is, totally disgusted with vista of POS and microsoft can it Deep and do not get windows 7, it is probably worse.  Is that all I can turn off to get the same performance than, say, windows 3.1?  It would be preferable to the current situation.  MSCKMA.

  Hello

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out what files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  Hope these helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Impossible to connect the computer to the internet after getting a virus

  Firewall settings

  I can't connect the computer to the internet after getting the following error message after I have used AVG 2011 to isolate and virus and rebooted my computer.
  Windows cannot connect to the internet using HTTP, HTTPS or FTP.  This is probably caused by the settings of firewall on this computer.
  Check the settings of firewall for the HTTP port (80) and HTTPS port (443) FTP port (21).

  I can't connect the computer to the internet after getting the following error message after I have used AVG 2011 to isolate and virus and rebooted my computer.
  Windows cannot connect to the internet using HTTP, HTTPS or FTP.  This is probably caused by the settings of firewall on this computer.
  Check the settings of firewall for the HTTP port (80) and HTTPS port (443) FTP port (21).

  Which firewall do you use? First, click on start > run > type inetcpl.cpl > Ok. Now, click on the "Advanced" tab On the Advanced tab, you should see a button to "restore the settings advanced". Click on the button. Follow the prompts all to confirm your selection. Then click on the 'Connections' tab > LAN Settings button. Make sure that there is a check mark in the box "Auto-Detection" parameters and that there is NOT a check mark in the box use proxy settings. Try to connect to the internet. Post your results please.

• Remote Desktop cannot find the computer

  Try to log on the server is running, I use windows 7 and internet explorer 8.

  I've used several times to link to you connect them to but it is hit and miss, I get the following text:

  Cannot find the computer XXXX

  Check the computer name and domain

  Any help as its very frustrating

  Hello

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  I suggest you to send your request in the TechNet forums to get the problem resolved.

  Please visit the link below to send your query in the TechNet forums:

  https://social.technet.Microsoft.com/forums/en-us/home?category=WindowsServer

  Hope this information is useful. Please come back to write to us if you need more help, we will be happy to help you.

• software isinstalled, but message comes up to make sure that your device is connected, the computer is not reconizing machine

  the software is installed, but message keeps occurring that make sure your device is connected.

  Hello

  Thanks for posting your query in the Microsoft Community Forums.

  According to the description, it seems that you are facing problems with the connection of the device that you get an error message "make sure that your device is connected, the computer is not reconizing machine." I'll be happy to help you with this problem.

  (1) device you're trying to connect?

  (2) how you try to connect the device?

  (3) what software is installed? Are what software you referring?

  (4) have you made changes on the computer before this problem?

  Method 1: I suggest you follow the steps in the link to run the troubleshooter and check if that helps.
  Open the hardware and devices Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2: You can also try uninstalling and reinstalling the drivers and check if the problem persists.

  To resolve this issue, follow these steps:

  1. to open Device Manager, click Start, click files, and research programsand typeDevice Manager. A list of the available items will appear above the search box; Click onDevice Manager. Device Manager opens with the name of your computer to the top and a list of the devices installed on your computer under the name of your computer.

  2. Locate the faulty device in the list of devices, right-click on the device, and then clickUninstall. When a warning message that you uninstall a device in your system, clickOK. Device Manager uninstall the device.

  3. right click on the name of your computer in the Device Manager, then click on Search the hardware changes. Device Manager scan your system and reinstall your device automatically.

  4 right click on the device, and then click Properties. Thegeneral of the device, in theState of the device Properties dialog box tab, you should see the message. This device does not work correctly.

  I hope this helps. Try the above steps and get back to us for further assistance if you have questions about the Windows operating system. We will be happy to help you.

• Cannot connect the macbook pro in normal mode

  Cannot connect the macbook pro in normal mode

  Are you getting errors?

  How do you connect? You use Safe Mode?

  What year/model MacBook Pro you are using and what version os OS X are you running?

• window of 2008: ' I can't open Group Policy Management "group policy to manage, you must log on to the computer with a domain user account.

  Hi, please advise, I can't open Group on win Server 2008 policy management, it is said
  "To manage Group Policy, you must log on to the computer with a domain user account.

  Hi Cucu KurniaPutra,

  Thanks for asking this question to Microsoft Community!

  The problem occurs in Windows Server 2008 Network, please post your request on the Microsoft TechNet forums to get help.

  
  Here is the link:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

  Kind regards!

• How to disable the automatic locking of the screen of the computer with windows XP

  How to disable the automatic locking of the screen of the computer with windows XP? so many people responded on windows 7, but NOT a SINGLE spoke of XP.  I have this problem.  screen goes into sleep mode and I have to wake up even if NO PASSWORD is selected.  I changed the POWER SETTINGS. Nothing helps.  NEED HELP. Thank you

  Well since it is already assigned, and a mod has not moved this somehow already in the XP section:

  On your desktop, right-click right properties, under the screen saver are of course "on Resume, display logon screen" is NOT checked. You can also disable screen saver.

• How can I reinstall Windows XP? I don't have my OEM of Windows ME records. I don't have my Windows XP to upgrade the disks I got the OEM. It was a free upgrade to Windows XP with my purchase of the computer with Windows Millennium Edition.

  How can I reinstall Windows XP?  I don't have my OEM of Windows ME records.  I don't have my Windows XP to upgrade the disks I got the OEM.  It was a free upgrade to Windows XP with my purchase of the computer with Windows Millennium Edition.

  I'm sorry, but you will need a Windows 9 x / ME drive to provide during the XP installation from the XP disc is a version upgrade. There is no way around that. See if you can find a friend with an older operating system disk (not a recovery disk) to support qualification. Otherwise, you would need to buy the full version (not upgrade) of XP to install on the computer. MS - MVP - Elephant Boy computers - don't panic!

• When the Admin sign on the office comes to the top, but after that the computer does not respond when the user tries to do anything. There are actually turns off the computer with the power button.

  Original title: user profile

  My administrator user profile does not work properly, but I have a user profile that has activated the parental control that worked well for about a year and yesterday when this user logs on the desktop comes up, but after that the computer does not respond when that user tries to do anything. There are actually turns off the computer with the power button.  I ran a virus scan and spyware scan in my user admin profile and he has not found anything.  I don't know what to check.

  Hello rhunter15,

  There may be a program to interfere with Parental controls so that we can try a few things to see if we can determine the application or program that is causing problems.

  First of all, we run System File Checker to see if you have a corrupt file system.

  • Click Start
  • Click on all programs
  • Click Accessories, and then right-click on the command prompt.
  • Select the Security tab and choose "Run as Administrator"
  • Click on command prompt
  • Type SFC/scannow.

  It will scan and repair any damaged operating system files.

  To determine if there is a program because of a conflict, we recommend that you perform a "clean boot" of the computer. A clean boot is designed to disable programs and services in the background as much as possible. This helps determine which service or program can be the cause of the problem.  For more information about how to perform a clean boot for troubleshooting, click the number below to view the article in the Microsoft Knowledge Base.

  KB 929135 - how to solve a problem of performaing a clean boot in Windows Vista.
  http://support.Microsoft.com/kb/929135

  Once you have finished the clean boot, check again and see if you get the error of parental control.

  If please post again and let us know if that helped pinpoint the problem or if you still need help.

  Thank you

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• To use the computer with the different Flight Simulator equipment that is only compatible with 32-bit versions of Windows

  Original title: change the version of Windows

  I have a computer used only for Flight Simulator and is running Windows 7 Home Premium 64-bit.  I want to use the computer with the different Flight Simulator equipment that is only compatible with 32-bit versions of Windows.  Is there a way I can upgrade to Windows 7 64 bit for Windows 10 32 bit and enjoy free upgrade of Windows 10?

  No, the upgrade program will replace existing windows with the same number of bits, 32 to 32 and 64 to 64.

  Even within the same version of Windows, passing from 32 to 64 and vice versa requires a clean installation.

• I bought a computer that has been renovated and the owner said that he has updated the computer with Windows 7, but the computer is now ask for an activation code.

  I need help to activate my computer but I don't have the code. I bought a computer that has been renovated and the owner said that he has updated the computer with Windows 7, but the computer is now ask for an activation code. I tried to contact the guy but he won't answer. Is it possible to check the activation without the code? I need help and do not want to pay a hundred dollars more.

  Is there a COA sticker that is attached to the machine?

  If so, check to see what edition and version of Windows machine is licensed to:

  COA certificate of authenticity:

  http://www.Microsoft.com/howtotell/content.aspx?PG=COA

  ??

  What is the certificate of authenticity for Windows?

  http://Windows.Microsoft.com/en-us/Windows7/what-is-the-Windows-certificate-of-authenticity

  Also:

  Please run the Microsoft Genuine Diagnostics Tool then copy and paste the results into an answer here for further analysis:
  http://go.Microsoft.com/fwlink/?LinkId=52012

• How to connect the Ombudsman with several bpel process

  Hi Please someone tell me how to connect the Ombudsman with several processes bpel in soa 11g

  And here

  http://eoracleapps.blogspot.com/2009/11/how-to-call-synchronous-BPEL-process.html