Cannot connect to the Eprint Page?

Similar Questions

• WRE54G cannot connect to the configuration page

  I use WRE54G and I can't connect to the device.  I have connected to my computer via a cat5 cable, but I can always connect to the Setup page.  Right now I'm getting a solid light.  I tried to connect to the unit when it shows the kept my "no internet wireless network
  access and have this problem for a few days.  I tried to use a static ip address and reset the unit, but nothing has worked.  I can't ping the unit either.

  I am very good with computers, but I can't understand this thing.

  What is the model of the router?

  By default the ip address of the WRE54G is 192.168.1.240... So assign ip address 192.168.1.10 subnet mask 255.255.255.0 and default gateway 192.168.1.240 on the computer which is connected to the WRE54G via cable.

  If it's still could not open the configuration page, then restart the WRE, power cycle the WRE and then try again.

• cannot connect on the start page, as the owner.

  computer froze on the star page. cannot connect as an owner.

  Hi mycasmas,

  1. don't you make changes before the show?
  2. the problem persists with other users accounts?

  Step 1: We recommend that you check if the problem persists in safe mode
  a. see Description of the Mode of course in Windows XP startup options
  b. in the menu advanced startup options select Safe mode and press on enter.
  c. connect to your user account.

  Step 2: If the problem does not persist in safe mode, check if a non-Microsoft program is causing the problem
  see How to configure Windows XP to start in a "clean boot" State .
  b. in the article, follow the method 1 and method 2 to find out if any program is causing the problem.
  c. Once you have found the culprit that is the program that is causing the problem, then uninstall it.

  Note: Article, remember to follow 'steps to configure Windows to use a Normal startup state. "

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot connect to the admin page of R6400 laptop, only on iPhone

  I installed a new router R6400 but can not access the admin of my laptop page. I was able to access it from my iPhone, so I am able to connect to the internet.

  I have talked to support 2 or 3 times and they always say the same thing: reset the router, type 192.168.1.1 in the address bar, try routerlogin.net or routerlogin.com, ping the router, check the IP address, etc. etc. I even tried to simply connect to the router via an Ethernet cable and still no go.

  Is someone can you please tell me why it does not work? I have read both articles, and they all seem to be saying the same thing. I just want to be able to access the admin of my laptop page. Someone at - he found a solution to this?

  I activated just improved Protected Mode and it worked. Don't know if it's the best solution (saw where to uncheck enable protected mode was an option too), but at least the admin site open - finally!

• EA-4500 cannot connect in the configuration page

  I try to connect to my EA4500 Setup page. I have the firmware "cloud connect" and when I get redirected to the "Linksys Smart Wi - Fi" page in my browser, I try to log in as usual. He accepts my username and password, then I get a page that contains a rotating chart and it says "waiting...". "He eventualy expires and brings back me to the login screen. I have tried rebooting my router and it does not help. I also unplugged the modem from the internet connection and entered the main router password, and gives me the same answer that if I tried to connect via the cloud.

  The only thing I can think of would be to do a factory reset of the router, but based on what is happening here, I'm frankly scared that I will never get my router online. I really wanted this cloud thing to work, but if I can get connected I will probably be back to the old firmware. Linksys gave us?

  I tried on several computers in the House and still have the same answer - no access to the router. At the end of the day, I did a factory reset and was finally able to get into the router. It was a pain to have to re - install my router, but at least I got all devalued parameters.

  For memory, the firmware had not changed since the introduction of the services cloud in June/July. I have the same exact firmware I downloaded in July. The only thing that has changed is that Cisco renamed "cloud connect" web interface for "Smart Wifi."  The web interface seems a little faster, but there are still a lot of wait time.

  I must be honest, based on this event, I was ready to go back to the old firmware, however, I'll give it one more chance to see if things will be better, or at least stabilize...

• Cannot connect to the eprint account

  Hello I have an OJ8600 N911n, Win8 running 64-bit with IE10. I opened an eprint account last week. This week(4/5/2013) I tried to open my account with my eprint address eprint and I could not connect. Today, I tried to login with my regular e-mail address and received this error message: submit Ajax failed. Error = 403, forbidden. Is this to say that I should use the eprint email address or I have to change pw and your email address? Thank you.

  Hello

  A simple solution to an error 403 Ajax is (a) using a diffrenet sea borowser or (b) clear the cache, history, cookies and try again.

  Kind regards.

• Classic BlackBerry set up questions - last get cannot connect to the wifi page

  Hi all

  far I have set up 30 + new Blackberry classic but the last issue is that once I have connected to the wifi I can't go through this page and the only options are previous!

  any ideas on how to move beyond this stage so I can complete the set up process?

  understand the question - under the date and the time of its establishment on auto update and this showed February 25, 2015 @ 9.31 am. changed to the current date and time and now I can exploit and set up the phone.

  Hope this helps others.

• Some Web pages do not allow (safari cannot connect to the server)

  I can't access some Web pages like the movie online, eBay, Amazon, etc. sites, when I try, I got the note as 'safari cannot connect to the server' and my chrome also got error like massage "this webpage is not available" more my App Store unable to work properly can not download updates»» I tried to delete all the data of the website... and uninstall extensions, but there was not work //I got a MacBook Pro 2014 middle with OS X EL capitan 10.11.2//some on help me please

  Please remove the 'ESET' product (if you have it installed) by following these instructions. If you have a different version of the product, the steps may be different.

  Back up all data before making any changes. Never install any product "anti-virus" or "anti-malware" again.

• Cannot connect to the Configuration of iballBatonADSL2RouterModem page

  I have Win 7 Machine, to reconfigure my network security cannot connect to the Configuration of iballBatonADSL2RouterModem page

  Hello

  Thanks for posting the question in the Microsoft Community forums.

  Looks like you are unable to connect to the Modem router configuration page. Please answer a few questions to refine the question.

  1. what happens when you connect to the Setup page?

  2. do you receive any error messages?

  3. you try to configure for the first time?

  You can view the guide provided by the manufacturer of the router.

  http://www.iballbaton.com/download/118/IB-WRA150N%20User%20Guide.PDF

  If the problem persists, I suggest you to contact the manufacturer of the router.

  http://www.iballbaton.com/enquiry.aspx

  Hope this information helps. Get back to us if you have more queries about Windows.

• Cannot connect to the HPConnected and ePrinting having the delay of 1 hour

  Hello

  Once connected to the ePrint I asked me to update for HP connected (I lived the delays of long hours of ePrint). The first time that it worked very well, but later I was not able to connect because the site causes an infinite loop: tries to go to en / us-> will detectlocale-> will fi / fi-> goes to en / us-> detectlocale-> fi / fi-> en / we...

  Can you please do something?

  Second thing is that you can not really rely on this service. I've been using ePrinting for 2 years now and whenever I need to print something more than a single document there are long delays and problems for connection etc. Last time this happened 2 weeks ago now today still.

  BR

  Did not help either. The same loop after login. I tried to connect to Snapfish - I had no problem.

  BUT, I tried to connect to the old ePrint and from there when I get the message that I've already updated, I can click the link to the HPConnected that seems to work. It worked not earlier, but now after this, I can also connect to new straigth to the HPConnected!

• HP Envy 4500: Printer says it has solid network connection, but cannot connect to the internet

  So I have not been able to use my printer wireless lately, so I decided to check if it was connected to my wireless network. It is; I checked, re-connected and checked several times. So I decided to reactivate my web services. I have them turned off, and now whenever I press the button on the printer ePrint, it says connection for a really long time and then displays the message in the sense of "the printer cannot connect to the server. Check the internet connection and proxy settings.

  I have re-connected the printer to my wireless network, I checked that if I use a proxy server (I'm not), I used the HP print and Scan Doctor - just, it won't just matter what I do.

  All I can think about is the fact that I have recently purchsed a new router, but says that its connected which is what really stem me.

  This printer makes me crazy - please help

  Hi @mastersword64,

  Welcome to the HP community!

  I hope you have a pleasant experience with us.

  I want to help you with the connection error, you get on your e-all-in-one of HP ENVY 4500 printer when you try to enable web services.

  Here are some steps, I suggest trying to get your web services up and running it again:

  Network Power Reset:

  We'll leave the router and unplug the power cable (NOTE: do not reset the router.), and then do the same with the printer and shut down the computer. After a minute, plug in the router, wait to fully turn on, then plug the printer back in and wait for the wireless light become solid. Once the router and the printer are on, go ahead and re - turn on the computer. This will refresh the network connection.

  Restore the default settings of the network and reconnect:

  1. on the front panel of the printer, press your up wireless icon

  2. Select settings.

  3. Select restore default network settings.

  4 turn on your printer.

  5. once it is initialized to save, press the wireless icon again.

  6. Select settings.

  7. Select Wireless Assistant , and then follow the prompts to enter the details of your wireless network.

  8. try to activate the web services again.

  Configure a manual DNS for your printer:

  1 obtain the IP address of your printer

  a. This can be done by pressing the icon on the printer wireless.

  2. Enter the printer's IP address in a browser on your computer.

  3. Select the tab network at the top of the page.

  4. on the left, select network.

  5. Select network address (IP)

  6. Select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  7. Select apply. You can get a warning simply select OK.

  Please reply to let me know if these steps resolve your issue.

  Good luck!

  

• HP 8500 printer and connection to the eprint Server

  Given to nine printer: HP Officejet Pro 8500 A910 n Premium (changes the status back to renovated 17/02/2011)

  ISP: ATT DSL

  Modem/router: 2wire new from Best Buy. It is white with ATT logo on it. Using the latest firmware.

  Network: ethernet

  The printer downloaded and installed an updated after initialization. If it is connected to the internet.

  Then tried to register the server says that it cannot connect to the server of the eprint and eprint.

  The functions of the printer normally in all directions except that it will not fit on eprint server.

  Many calls and hours with the reboot, reset HP support and everything else under the Sun did nothing.

  I tried to place the IP addresses and DSN by any suggestions on these forums and nothing works.

  Could there be a problem with the HP Sever? Does it really exist? Are there problems of compatibility with 2wire router.

  ATT session remotely on my computer and could find nothing they could do. They were able to draw a page of remote test.

  Any suggestion or help would be greatly appreciated. Thank you.

  NEW INFORMATION (11/02/2011):

  I noticed today just by looking at the integrated Web server, printer SSID is not the same as the router, but it is grayed out. Is it important for ethernet? If so how can I change? I don't think it's important for the ethernet.

  NEW INFORMATION (12/02/2011):

  The 2wire support team gave me the procedure to open completely all the in and out traffice to the printer. They said that if it does not, then the problem is with the eprint server. I'll try this Monday, but I expect a communication problem between the printer and the eprint server that does anything at my place or my ISP. Is it possible to check this printer is trying to connect to the server? Where is he? Is it operational? If this is not the case, is it rerouted properly to a working server? The printer must attempt to access an IP or DNS address to establish communication magnified.

  NEW INFORMATION (14/02/2011):

  According to the 2wire support team I opened all the ports and enabled all services then turned the printer market. It did not work. The printer does not connect to the HP eprint server. So the problem is with the HP eprint server. This printer is programmed to search for a server to connect to somewhere. Where is he? Is it operational? Why will not allow a connection? HP, the ball is in your court. What can we do?

  I have ATT DSL at work and at home Charter cable service. The problem is the same for the locations and ISPS. Y does it have that someone out there has connected to ATT DSL or cable of the Charter? If so, what are your settings?

  NEW COMMENT (15/02/2011)

  Can someone at HP tell me why the printer connects to the server HP and download the firmware update, but does not connect to the HP Server to register for eprint? All this seems to be on the side of HP. When do we get a fix?

  NEW COMMENT (16/02/2011)

  The model number is empty in the Engineering menu and page printer card. If there is a problem can be added with an update of the firmware? What I need to get money for it and buy one set entirely in a local store? Virgin model number is maybe to throw all other incongruous information that is sent to the server. The server can be updated to accept Virgin model numbers?

  THE PROBLEM - SOLUTION PENDING POSSIBLE SOURCES (16/02/2011)

  I JUST LOOKED AT THE BACK OF MY PRINTER. IT HAS A STICKER ON IT RECONDITIONED.

  It seems that the number of missing on the remanufacturered units model is the reason why it does not connect to the eprint server. Print the diagnostic printer page and see if the model number is empty.

  HP is working on a fix.

  SOLUTION-(22/02/2011)

  I UPGRADED MY ORDER WITH RENOVATED WITH NEW REPLACEMENT. THE REPLACEMENT AGAIN CONNECTED THE FIRST TIME TO THE SERVER EMPRINT - NO PROBLEM. I HAD TO PAY FOR A NEW AND THEY WILL CREDIT MY CARD WHEN THEY REACH THE RENOVATED A RETURN.

  LESSON LEARNED - IF YOU HAVE THE PRINTER WITH THE VIRGIN MODEL NUMBER YOU CAN NOT CONNECT TO EPRINT, NO MATTER WHAT YOU DO!

  Thanks if anyone can help.

  SOLUTION-(22/02/2011)

  I UPGRADED MY ORDER WITH RENOVATED WITH NEW REPLACEMENT. THE NEW REPLACEMENT CONNECTED FIRST TO THE SERVER EPRINT - NO PROBLEM. I HAD TO PAY FOR A NEW AND THEY WILL CREDIT MY CARD WHEN THEY REACH THE RENOVATED A RETURN.

  LESSON LEARNED - IF YOU HAVE THE PRINTER WITH THE VIRGIN MODEL NUMBER YOU WILL NOT BE ABLE TO CONNECT TO EPRINT, REGARDLESS OF WHAT YOU DO!

• Help! Safari cannot connect to the server

  I really need help! I tried to forget the network and turning it back on, I have disabled the firewall and remove all extensions of safari. I seems that nothing works.

  I get the message 'Safari cannot connect to the server' on almost every site except this and facebook. I can't enter same Urbanoutfitters.com or ASOS. I just got the message "Safari could not connect to Server" I'm not a computer genius so hopefully someone here can help me...

  You may have installed one or more variants of the malware "VSearch' ad-injection. Please back up all data, and then take the steps below to disable it.

  Do not use any type of product, "anti-virus" or "anti-malware" on a Mac. It is never necessary for her, and relying on it for protection makes you more vulnerable to attacks, not less.

  Malware is constantly evolving to work around defenses against it. This procedure works now, I know. It will not work in the future. Anyone finding this comment a couple of days or more after it was published should look for a more recent discussion, or start a new one.

  Step 1

  VSearch malware tries to hide by varying names of the files it installs. It regenerates itself also if you try to remove it when it is run. To remove it, you must first start in safe mode temporarily disable the malware.

  Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for other instructions.

  Step 2

  When running in safe mode, load the web page and then triple - click on the line below to select. Copy the text to the Clipboard by pressing Control-C key combination:

  /Library/LaunchDaemons

  In the Finder, select

  Go ▹ go to the folder...

  from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

  A folder named "LaunchDaemons" can open. If this is the case, press the combination of keys command-2 to select the display of the list, if it is not already selected.

  There should be a column in the update Finder window. Click this title two times to sort the content by date with the most recent at the top. Please don't skip this step. Files that belong to an instance of VSearch will have the same date of change for a few minutes, then they will be grouped together when you sort the folder this way, which makes them easy to identify.

  Step 3

  In the LaunchDaemons folder, there may be one or more files with the name of this form:

  com Apple.something.plist

  When something is a random string, without the letters, different in each case.

  Note that the name consists of four words separated by dots. Typical examples are:

  com Apple.builins.plist

  com Apple.cereng.plist

  com Apple.nysgar.plist

  There may be one or more items with a name of the form:

  com.something.plist

  Yet once something is a random string, without meaning - not necessarily the same as that which appears in one of the other file names.

  These names consist of three words separated by dots. Typical examples are:

  com.semifasciaUpd.plist

  com.ubuiling.plist

  Sometimes there are items (usually not more than one) with the name of this form:

  com.something .net - preferences.plist

  This name consists of four words (the third hyphen) separated by periods. Typical example:

  com.jangly .net - preferences.plist

  Drag all items in the basket. You may be prompted for administrator login password.

  Restart the computer and empty the trash.

  Examples of legitimate files located in the same folder:

  com.apple.FinalCutServer.fcsvr_ldsd.plist

  com Apple.Installer.osmessagetracing.plist

  com Apple.Qmaster.qmasterd.plist

  com Apple.aelwriter.plist

  com Apple.SERVERD.plist

  com Tether.plist

  The first three are clearly not VSearch files because the names do not match the above models. The last three are not easy to distinguish by the name alone, but the modification date will be earlier than the date at which VSearch has been installed, perhaps several years. None of these files will be present in most installations of Mac OS X.

  Do not delete the folder 'LaunchDaemons' or anything else inside, unless you know you have another type of unwanted software and more VSearch. The file is a normal part of Mac OS X. The "demon" refers to a program that starts automatically. This is not inherently bad, but the mechanism is sometimes exploited by hackers for malicious software.

  If you are not sure whether a file is part of the malware, order the contents of the folder by date modified I wrote in step 2, no name. Malicious files will be grouped together. There could be more than one such group, if you attacked more than once. A file dated far in the past is not part of the malware. A folder in date dated Middle an obviously malicious cluster is almost certainly too malicious.

  If the files come back after you remove the, they are replaced by others with similar names, then either you didn't start in safe mode or you do not have all the. Return to step 1 and try again.

  Step 4

  Reset the home page in each of your browsers, if it has been modified. In Safari, first load the desired home page, then select

  ▹ Safari preferences... ▹ General

  and click on

  Set on the current Page

  If you use Firefox or Chrome web browser, remove the extensions or add-ons that you don't know that you need. When in doubt, remove all of them.

  The malware is now permanently inactivated, as long as you reinstall it never. A few small files will be left behind, but they have no effect, and trying to find all them is more trouble that it's worth.

  Step 5

  The malware lets the web proxy discovery in the network settings. If you know that the setting was already enabled for a reason, skip this step. Otherwise, you should undo the change.

  Open the network pane in system preferences. If there is a padlock icon in the lower left corner of the window, click it and authenticate to unlock the settings. Click the Advanced button, and then select Proxies in the sheet that drops down. Uncheck that Auto Discovery Proxy if it is checked. Click OK, and then apply.

  Step 6

  This step is optional. Open the users and groups in the system preferences and click on the lock icon to unlock the settings. In the list of users, there may be some with random names that have been added by the malware. You can remove these users. If you are not sure whether a user is legitimate, do not delete it.

• When I connect to the start page of mozilla, I can't go to any other sites Web - get "unable to connect to the server", but I'm still able to access the internet through Internet Explorer on the same computer.

  Cannot move to the start page of Mozilla. Any site or search I run, I get a message that Mozilla can not establish a connection with the server.

  See this support article - difficulty of problems connecting to websites after Firefox update

• HP8600 does not connect to the ePrint Server

  HP8600 does not connect to the ePrint server at all. I double checked all the settings and I can print to it from my applications when you are connected to the same network, but try to access the server of ePrint from the screen of the printer or the web interface cannot establish a connection.

  The printer is connected via a wireless network and can be printed from any device connected to our network.

  Everything indicates that there should be good. But can't seem to make bad connection ePrint. No error message not developed.

  The printer is on a network of b/g/n 2.4 GHz connected to a Netgear N600 DUal Band (WNDR3700 model).

  Version of the firmware of the printer is CLP1CN1232AR

  Any ideas? It does not appear to be blocked by a firewall, so really lost here.

  Hello

  Try to define an alternative DNS and check if that can help you:

  1. Tap the wireless on the top of the screen of the printer and look for the IP address is.
  2. Navigate to throguh IP of the printer, the web browser on your PC.
  3. Click the network tab.
  4. Under, click IPv4 wireless.
  5. Under the DNS Configuration, select manual.
  6. Set the address preferably as 8.8.8.8
  7. Set the e-mail address alternative as 8.8.4.4
  8. Click on apply to confirm the change.

  Now, turn the printer off and turn it back on and check for the difference.

  Shlomi