Cannot disable touchpad on laptop. does not display the properties of inmouse

Similar Questions

• HP pavilion dv6 laptop does not display the logo of beats

  the beats logo used for the poster when I changed the volumes, but after that I used windows easy transfer it don't it shows more. I checked the settings of beats, but there is no option to make it appear again. any suggestions?

  You may need to reinstall the drivers of Beats on the HP site.

  FTP://ftp.HP.com/pub/SoftPaq/sp52501-53000/sp52658.exe

• my touch pad on my laptop does not move the pointer, but when I have my mouse wireless pluged in it will work I was told I could have disabled the touch pad which I have to do to activate it again?

  my touch pad on my laptop does not move the pointer, but when I have my mouse wireless pluged in it will work I was told I could have disabled the touch pad which I have to do to activate it again?

  Hi dove2k,

   

  Welcome to Microsoft Answers Forums.

  You will need to enable the touchpad on the laptop itself.

  Find the area of the touch pad, you will find a button to enable or disable the touchpad.

  If the step above doesn't, try this step.

  Go to control panel > mouse > device settings tab
  Click (or to disable)

  

  Notes:
  On some models, there is a keyboard shortcut to enable or disable the touchpad. For example, ACER, just do Fn + F7.
  You can click on Reset device if none of these solutions work.

  If you still can't touch pad to work, you will need to contact the manufacturer of the laptop computer for more information.

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• my iphone 5 s has been disabled. I'm trying to restore my iphone with itunes and itunes asks me to put the password for my iphone. but my iphone does not display the unlock screen. What should I do now?

  my iphone 5 s has been disabled. I'm trying to restore my iphone with itunes and itunes asks me to put the password for my iphone. but my iphone does not display the unlock screen. What should I do now?

  Hello

  Follow the instructions here:

  If you have forgotten the password for your iPhone, iPad or iPod touch, or your device is disabled - Apple supports

• After installation or upgrade to Firefox 31, starting Firefox does not display the home page, personalize displays a blank page and the radio button does not work

  I am the admin of Windows for a University Department and install PC with Firefox all the time. This problem does not occur with every PC I would maintain, only a selection bit (model different laptops with Windows and update 1 8.1.) Until today, it has happened with the new user (with admin rights) accounts that I place on laptops for our staff. Today, this happened with the account administrator while setting up a new laptop. In all cases so far, I have install Windows from a registered image that was created by using sysprep.

  I tried many suggestions to reset Firefox, removing the profile of Firefox users, removing the Windows profile users, uninstalling/reinstalling Firefox, uninstall/reinstall of Firefox and the latest Java, but nothing helped. After uninstalling, I run an application to delete the caches and temporary files and even remove manually the keys to register HKLM\SOFTWARE\Mozilla and HKCU\SOFTWARE\Mozilla. I restart and make sure that the installation folder is deleted after uninstalling.

  Results are the same: after installing Firefox 31, the initial settings for migration, IE or Chrome pop up and after having clicked on the button finish, Firefox starts but does not display the home page of the new user, only a blank page. By clicking on the Options (3 bars) button does nothing. Right click in the appropriate box, the shortcut menu appears, so I can choose to customize, but which opens another tab with subject: Customize the URL and the page is blank. In the right click context menu, I can activate the menu bar and get options from that.

  My last attempt helped a little. I uninstalled Firefox 31, cleaned, removed the profile user Firefox, rebooted and then installed Firefox 30. Initial start-up runs and tells me that I'm not up-to-date and the works of button Options. But I can't always customize.

  Then I upgraded to Firefox 31, but then it's back to no start page, no options button and no customization. I can go down to 30 and get customize practically works again.

  Addon only is for McAfee Scriptscan to Firefox 15.1.0, just after installation is disabled.

  Any help would be appreciated. Thank you.

  You can try a different theme of Windows?

  Have you tried to start the computer using Windows safe?

  Start the computer in Mode safe mode with network support Windows (on the startup screen, press F8) as a test.

  • http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/

• Windows does not display the CD-ROM drive

  A week ago, my computer stopped showing me an icon for my DVD player. When I go into the Device Manager there is no option for CD/DVD players. I tried Microsoft Fix It, and he told me that there is no CD drive. I can not re - install a driver because the Device Manager does not display the CD players.

  I did not major changes to my computer I know so I can't imagine what the problem is. Help?

  Trevor

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================================

  After the foregoing:

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• My laptop does not recognize the DVD drive or an external USB DVD drive.

  My laptop does not reconise the integrated DVD or an external USB, DVD player.  But if I set the BIOS to let the laptop for the start of the DVD player and the DVD player worked fine.  He could read the disc.  Once, I deleted the program Nero of the system and I don't know if some Windows file has been corrupted.

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find CMD top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ===================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please make all underneath the same if you have done some before as is often
  the set of operations that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device.
  The driver tab - click on update drivers (this will probably do nothing) - then do a RIGHT CLICK
  the reader - UNINSTALL - REBOOT this will refresh the default driver stack. Even
  If the drive appears not to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, might
  having a cable loose or slight corrosion on the contacts (usually for a laptop) and
  other questions.

  Your CD or DVD drive is missing or is not recognized by Windows or
  other programs
  http://support.Microsoft.com/kb/314060

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other
  programs - a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that
  you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the
  Setup Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then check
  in both ends of the cables. Remove and replace, do not just tight. For portable computers, you can
  Often, clean power and contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the system
  Designer and manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case
  (Read burn CD & DVD and CD and DVD). So it is not unusual for 1 or 2 pieces
  No function while others do so properly.

  Did you follow the Troubleshooting Guide for the reader who still does not work? He
  are some registry entries that do not fix the resolution of problems and those who "might".
  be the cause.

  Check with your system manufacturer Maker and possible device for two firmware
  updates and the correct registry entries for your car.

  Here are the keys in my opinion, are those in question - for the CD/DVD drive - sub
  the key of course because there will be other subkeys in these keys. Do not forget to ask specific
  involved as well as the settings key.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://Club.myce.com/F61/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a restore
  Point before you change anything whatsoever) - find the DevManView device and then right click it open in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager,
  that displays all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• My firefox does not display the icon fonts!

  I use fontello.com for my web design project. But recently it does not display the icon.

  and the strange thing is that its OK my Firefox friends and just my PC have the problem.

  for example, this page shows icon on my friends firefox but I can't see the icons
  https://DL.dropboxusercontent.com/u/28793409/fontello-d3b0f38a/demo.html

  That's what I see
  https://DL.dropboxusercontent.com/u/28793409/shot.jpg

  If Safe Mode is good, the more likely culprits are one of your extensions or incompatibility of the graphics driver. To work around the second question, you can disable use of the hardware acceleration Firefox to see if that helps.

  "3-bar" menu button (or tools) > Options > advanced

  In the mini ' General' tab, uncheck the box for "use hardware acceleration when available.

  It takes effect the next time you exit and restart Firefox.

• Navigation toolbar does not display the URL

  When I go to a website, the section of the navigation toolbar that displays the URL of the page is no longer indicates the URL http://www as he always did in the past. The size of the part has been reduced. Has expanded the area where you type URL for search engine. I have no problem with the navigation, history, bookmarks, tabs bar, etc. Only problem is that the URL does not display the page. Even this page has no URL displayed in the navigation bar. It has the logo for mozilla and when I put the cursor on it, it says it all "Web site does not provide identity information." The same shows for each site than go. Yes, I can to bookmark the page without any problem and can use bookmarks to return to the page. But no URL appears in fact as he always did in the past. Oh, I have an IMac and use a keyboard of razor.

  Hello.

  You should be able to resize the address bar, if the search bar is to the right by simply sliding the space between the address bar and the search bar.

  If that does not solve your problems, it is possible that you have a problem with some Add on Firefox which is an obstacle to the normal behavior of your Firefox. Have you tried to disable all add-ons (just to see) to see if Firefox goes back to normal?

  Whenever you have a problem with Firefox, whatever it is, you must make sure that it is not caused by one (or more) of your installed modules, whether an extension, a theme or a plugin. To do this easily and cleanly, start Firefox in safe mode (remember to select disable all add-ons when you start safe mode). If the problem goes away, you know that it's an add-on. Disable them all in normal mode and allow them one by one until you find the source of the problem. See this article for more information on troubleshooting extensions and themes and this one for plugins.

  If you need help with one of your modules, you will need to contact the author.

  If the problem does not disappear when all add-ons are disabled, tell me please, then we can work from there. Please be afraid not to follow my instructions to the line, as everything can be easily undone.

• CD\DVD player does not display the contents of the data DVD.

  CD\DVD player does not display the contents of the data DVD, but will display the content of the data CD.  What is happening on more than one PC, and it began when Active Directory GPOS have been applied for the PC.  If untying policies the problem persists.  What happens on DVD ROM and DVD RAM drives.  Scanning software has been added to these machines, think it might be an ASPI crush.  All these machines are XP SP3 running McAfee.  When you insert a DVD with data on this topic, the name of the drive in windows password DVD RAM drive to CD drive, and if you try and browse the DVD it displays as a blank CD.  I changed something on the PC with the policy but cannot understand what he.  Other identical PC can view the contents of the DVD very well, but they never had the same strategies.  Any ideas, thank you.

  Hi PDoneen,

  The restore of the system; restore the computer to the before date when policies have been launched on one of the affected computer.

  You can check the link for the steps below: how to restore Windows XP to a previous state:http://support.microsoft.com/kb/306084

  Post back with the results.

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• BlackBerry Tour 9630 smartphones does not display the name of the caller

  Hello

  I have a Tour 9630, version sw 5.0.0.732.  When the phone rings, it does not display the name of the caller, their telephone number, although this number is in my address book.  Once I answer the call, the name will be displayed.

  Naturally, I would like to know who is the caller before I answer!  :-)

  I found a few messages, ask something similar, although for different model phones.  Some of them suggest that I have to disable protection for the content... but I can't find it in the options.  Even in the User Guide, it contains instructions (go to Options > Security Options > General settings... but there is no "General settings" on my phone.)

  If anyone knows how to solve this problem, I would be very grateful!

  Kind regards

  Options > Security > encryption > include contacts.

  There could be other solutions... Try these:

  1. make sure that you set your own country code to the Phone Dialer screen > Options > smart dialing.
  Set your country code in this format: "+ xx" where xx = country code. Some countries have two or three-digit country Codes. Do not place not the '+' in the entrance of your contact.
  * In the United States, the value of this country as '+ 1' Code and place your local area code in the appropriate box (this normally the default setting in a new BB).

  2. in the same place, change the length of National number for the number of digits corresponding to your country (since some countries have less than 10 as that set by default in the BB). Check out the total numbers, less country code. Do not place not the '+' in the entrance of your contact.
  * For example, some countries have a total number to 8 (more than 3 for the country code). You must enter '8 '.

• My Firefox has just automatically updated itself to the version 42. The extention under modules page does not display the extensions I have installed.

  My Firefox has just automatically updated itself to the version 42. The extention under modules page does not display the extensions I have installed. The plug in page shows the plug ins I installed. How can I fix it? This happened on my 64 bit Windows 7 partition. I installed the extension "classic add-on" to see if she could solve the problem. There is unfortunately no. I have a screenshot. I'm not sure if I have permission to upload it to the media gallery. I also use Linux, but I did not upgrade that are still there.

  It is possible that there is a problem with the files that store the registry extensions.

  Delete the files (extensions.json, extensions.sqlite, extensions.ini) extensions.* and compatibility.ini in the profile folder of Firefox to reset the extensions registry.

  • https://support.Mozilla.org/KB/profiles

  New files will be created if necessary.

  See "extension corrupted files:

  • http://KB.mozillazine.org/Unable_to_install_themes_or_extensions
  • https://support.Mozilla.org/KB/unable+to+install+add-ons

• When I open a link in a new window does not display the web address.

  When I open a link in a new window does not display the web address. What have I done wrong? It used to work and it works if I open the link in a new tab, the problem is that I hate to use tabs prefer a new window every time... Help!

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > appearance/themes).

  • Makes no changes on the start safe mode window.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• URL address box does not display the current page.

  With the 4.0.1 update, the URL address box does not display the current page.

  All that shows is the text: «Go to web site»

  To now see the url of the current page, you need to make a right click the empty space is the address box and press the button "esc".

  Is there a way to display the url of the current page?

  This problem may be caused by an extension that is not working properly.

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions of the origin of the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > appearance/themes).

  • Makes no changes on the start safe mode window.
  • https://support.Mozilla.com/kb/safe+mode
  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox

• Save dialog box under does not display the list of files

  Terminal Server R2 of 2012.  Dialog box "Save as" for a user does not display the list of files.  The address bar shows the way, there is a form for the file name box, and the user can save the file successfully.  But the space that would show the files in the selected directory is empty.  There is no form for the list of files box, it's just the grey box dialog box space - that is to say, it is not that it looks like an empty folder, there is simply no display form box.

  The 'Open' dialog box appears normal, showing the list of files in the selected folder.

  I had the user close the session on the Terminal Server and access it from another PC, even if I was not expecting to make a difference, and it didn't.  I have also connected on myself and has not experienced the same problem.  So it seems to be user-specific.

  What a setting, the user has selected by mistake, or a mistake any?

  Thanks for any help.

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.