Cannot enter BIOS or Option of Boot to display on my desktop Acer Aspire M3450

Similar Questions

• Cannot enter BIOS or boot from CD - Satellite 5100

  Hello

  one of my friends has ruined his Toshiba Satellite 5100.
  He has erased all the partition on the disk hard while the laptop always using the default setting.
  so, I could not boot from the cd or enter the BIOS.
  Is there any solution for this?

  Thank you

  Hello

  You can use different ways to boot from the CD drive.
  You can press the C key immediately after restarting the laptop.
  In this case, the laptop should boot from the CD. (Don t forget to insert the CD)

  Another way is to change the boot order in the BIOS. To enter the BIOS, please use the ESC key.

• Cannot enter BIOS on Win 7 HPE with American Megatrends BIOS

  Although others have asked how to access the BIOS Setup interface, the answers have not solve my problem. so I write another similar question.

  According to the subject line, I can't access the BIOS Setup interface during startup.  My system runs Windows 7 HPE.  The equipment includes an elite group of ECS motherboard that came with BIOS of American Megatrend chip version 4.6.5 and is dated 05/03/2012.  I have never flashed or otherwise updating of the BIOS chip, but I could bring up the graphical user interface and change the options.  I did quite recently in fact.

  When I power fail system and/or entering the cycle of rebooting from the button start, the system stops and then begins to start and displays the start of American Megatrends screen.  Press DEL repeatedly has no impact on the continuation of start-up.  He proceeds as if the keyboard were not active and the system did not, therefore, the interruption of the keyboard...  Because the splash screen also mentions F2 and F7, I tried these interruptions as well, nothing helps.  The boot process has continued.

  I searched the web until my fingers are simple bumps and can't find anything really useful.  I read and reread mother ECS card manual without finding anything.  I found a FAQ on the web page of American Megatrends, which addressed problems to access the BIOS with Win 8, which suggests that the change of power options would be effective. However, these referenced power options do not exist in my win 7 system HPE.  Yes, Power Options are available from the Control Panel, but the individual options are not the same to win 8.

  FWIW, I pulled all the hard disks internal power cables to see if I could access the BIOS interface.  I was able to do so; However, without BONES, the keyboard is not active so no keyboard interrupts can be issued.

  I would be grateful for any advice on how to influence of post-processing to slow down and make sure that any issue the keyboard interrupt is seen and followed.

  Hello

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  By the description, I understand that the problem with you are not able to enter the BIOS American Megatrends BIOS setup.

  I can understand the inconvenience that you have experienced and will try my best to help you.

  In order to get more information about this, I suggest to visit the link below and check if that helps.

  http://***.com/products/BIOS-UEFI-firmware/

  Also, I suggest you to update the BIOS and check if that helps. Please visit the link below and check if that helps.

  BIOS: Frequently asked questions

  http://Windows.Microsoft.com/en-in/Windows/BIOS-FAQ#1TC=Windows-7

  Important: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

• Cannot enter BIOS - Satellite-P50t-A-119

  Cannot get into the BIOS. F2 works Océ try 20 times. Same problem with the F8 key. I tried 30 times, it worked only once. Laptop is brand new.
  Is there a stable way to get into the Bios?
  Is there a stable way to use the F8 key.

  I never had problems like this with different computers

  Hello

  If you have a new machine with Win8, you must perform a full stop in a first time. Check it please http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm
  It is explained how to do this. Restart your laptop, and you should be able to enter the BIOS settings. I don't know which F button, you need to use but on my I use F12 and there entry option settings.

  Check it out please.

• ThinkPad E330 cannot enter BIOS/UEFI more

  Hey guys, I got a very annoying problem with my E330.

  He came without OS, so I put 8 Win on the preinstalled HARD drive. Then, I went out for one SSD and put Win 7 on it.
  (all UEFI mode)

  Since then I can not enter in the BIOS/UEFI more press either Enter or F1.
  Pressing enter gives me still a beep, but then Windows continues to load normally instead of view several options, like he used to do.

  And yes I am aware that I need a cold start to Win 8 to enter the UEFI

  The only way to access UEFI at this time is through charms-bar restarting 8 Win in UEFI thing.

  I tried to reflash the BIOS that does not of course because this is the same version, tried to remove the CMOS battery, that gave me an opportunity to enter the UEFI with F1 when he complained the date/hour of time.

  Switching to Legacy only brings me to an infinite PXE - something loop of the error, but I still cannot get into the BIOS.

  I tried pressing all combinations of keys Fn + F and without the Fn. Nothing works.

  I don't want to return the laptop, but it is a deal breaker for me if I can't Win 7 running on this subject with UEFI accessible.

  OK, the problem was solved with the help of the someotherguy of the user from the forum. It has detailed instructions.

  Looks like that install Win 7 mode UEFI corrupts the BIOS.

• Cannot enter BIOS mode

  1. type of computer - ENVY HP dv7-7250nr

  2 opporating 8 64-bit windows system

  Recently, I received this computer. It is amazing that the only thing that could use a change is the keyboard. I got this as a gaming PC, but the function keys can be accesed when you press FN. In most computer games, the keys f # are your shortcuts. When I go to press me I windows has changed and the control panal appears.

  So I was looking around, and they say you can switch mode BIOS and disable shortcut keys. Only problem is that I can't enter the BIOS mode.

  I would be really grateful for the help on this, I don't want to go out and a whole-nother-key keyboard.

  Thank you in advance.

  PS. I hope, I put this is the right forum, if not then I'll post in a new one.* *.

  Princess.

  As soon as you turn on the laptop tapping on f10 key only starting.

  You must be quick.

  REO

• HP Pavilion g6-1313sh Notebook: dual Radeon graphics card - cannot enter bios mode fixed

  Hello!

  I recently bought this laptop apart from my friend and is struggling with this for a few weeks now.

  I was on the forum every day for a few hours without result.

  so, my laptop is HP Pavilion 1313sh g6 with Win7. I have the latest version of the bios, so I could put my gpu bios mode set instead of dynamic.

  Here's the problem... When my setting was dynamic, I got the "switchable graphics" option and I could put the preset by application. as many people pointed out, it really does not work, so I went back to fix.

  This option is now missing. so I tried in CCC, following this: http://support.hp.com/us-en/document/c03048374 in the fixed bit.

  It is, I have no change option... I only get the graphics card AMD Radeon Dual 'activate' or disable... but not the button to switch permanently to the highest performance card... checked in CCC, it recognize my 2 cards under hardware (1st HD6520G 2nd is Hd7400M).

  I start to tear up the rest of my hair. Please can someone tell me what I miss? as said, the most recent drivers from the site is all settled.

  Thank you!

  Hi @SmokeyJohnny ,

  Thank you for visiting the Forums HP's Support and welcome. I looked in your question about your HP Pavilion g6-1313sh Notebook and issues with graphics switchable. You can do a System Restore. System Restore will help if something is automatically updated and wasn't on the laptop.

  When running a system restore note remove all USB devices. Disconnect all non-essential devices because they can cause problems.

  If this does not resolve the problem would be to uninstall the graphics drivers listed in your device manager. Reboot the laptop and it must be reinstalled the proper drivers. Yours is the AMD Radeon HD 6520 + 7450 Mr. here are your drivers if you need.

  I hope this helps.

  Thank you.

• V3 - 771 cannot enter BIOS to rebuild from recovery DVDs

  Hi all

  My installation of Windows 8 has been corrupted and does not start. So I just want to get the laptop to boot from the recovery DVD or any DVD so I can rebuild.

  No matter how hard I press F2, nothing happens and I get "no boot device, press a key." It just takes me to a blank start menu! I tried with what I know to be bootable CD/DVD internally and have used external DVD drives.

  I want to just get into the setup to boot from the DVD drive. How difficult that can be. Very far and completely frustrating.

  Any advice or help welcome.

  Thank you very much for your time.

  Paul

  Hello again,

  This problem is corrected now strangely. I had tried to start on many drives of type Ultimate Boot with no luck. I jumped in a DVD of Windows 7 which has started loading, but didn't the first time.

  I rebooted and then the "F2" worked well. I changed the classic UEFI BIOS got up the menu key to boot at startup and started on the DVD of Windows 7. Load up now very well.

  This is nuts. Affect the initial installation of Windows 8 that crashed BIOS/UEFI? I'm old school and both should be completely independent. The operating system should have nothing to do with the computer startup mechanism.

  Thank you very much

  Paul

  Edit: Looks like Secure Boot is the guilty https://technet.microsoft.com/en-us/library/hh824987.aspx

• p6320f cannot enter BIOS

  Hello

  I have a serious problem I think...

  My p6320f freezes usually just on the HP logo... Sometimes, however, if she was going on the logo, it shows an error something like "unable to boot from the hard drive.

  He can't get into the BIOS! No matter how many times I press F10 (or any other F keys), it freezes.

  PS: Just installed a new Seagate 2 TB internal SATA hard drive after the failure of the original

  Any ideas?

  Thank you

  johnstevens wrote: Hey Hanspuppa if it's the fault of the card from my mother, it means I need a new computer?

  Or can I just know what part of the motherboard is defective? If so, how? Thanks for the help. JS

  Hello johnstevens, usually the only element on the motherboard that can be replaced by the user would be the CMOS battery.

  I replaced motherboard capacitiors failed a few years ago, when these faulty capacitors have been a real problem for the PC industry. This problem has since been resolved largely. Different types of motherboard capacitiors are now used.

  There are also some cards diagnosis motherboard which are used to diagnose motherboards, but they are mainly used by manufacturers of motherboards. When they find a defective item on the motherboard, they have the tools and expertise needed to replace the defective item and it recheck once the repairs have been made.

  If the CMOS battery does not solve the problem, a motherboard replacement seems to be the most viable solution, or buy a new computer. These replacement motherboards can both, cost half the price of a new Tower.

  You wouldn't need a new monitor unless your current monitor is an old, defective, or you want a larger screen size.

• Cannot enter BIOS using F1 or entry

  I'm at a complete loss here. Brand new T430. I changed the settings in the UEFI BIOS and installed Windows 7 x 64 with success. But I can't get into the BIOS. Entrance to F1, F12, nothing works.

  Help, please!

  Thank you very much!!

  Hi all

  I solved the problem. Just an update of the BIOS!

  Strange that the initial BIOS does not work!

  Thank you

• Cannot enter gateway ipv6 address while booting in Vsphere Management Assistant

  Hello

  After you deploy the model to the FVO, I have to configure the network settings for the device of the VMA. When you try to put the default gateway, I have to configure an ipv6 address. As we don't use ipv6, I tried to enter private ipv6 addresses, but I keep getting errors.

  

  The documentation states:

  If you use a static IPv4 network configuration to configure the IP address, DNS, default gateway and hostname, you must also configure the IPv6 default gateway when you first start network set up, otherwise the vMA may be inaccessible from the network after the connection.

  No help for configure this VMA is very appreciated!

  Friend

  WIllem

  Able to proceed to the configuration of the network after a reboot of the device of the VMA.

• Tecra M5 cannot enter the BIOS to change the setting too boot from cd first

  Tecra M5 cannot enter the BIOS to change the setting too boot from cd first

  I bought on ebay and the seller sold me a dubious version of xp so I want to format and install my own at the start he said:

  The Intel Boot Agent GE v1.2.31 initialization
  KE - E05: the LAN adapter's configuration is corrupted or has not been initialized. Boot agent cannot continue

  Hello

  The message looks like you tried to boot and install Windows LAN

  If you want to change the boot order, I recommend pressing the F12 key, immediately after that the laptop was turned on!

  A new start menu should appear, then you can choose the reader of CD/DVD (ODD) and a boot device.

  Also by pressing the C button should allow you to boot from the CD inserted, bootable.

  Welcome them

• ThinkPad 13 - cannot enter the UEFI BIOS without entering the W10 first

  I have a brand new 13 Thinkpad which I'm really pleased.  However, the user manual seems to be wrong.  I can't enter the UEFI BIOS in F1.

  It seems that the only way to get into the BIOS is first go to W10 and make a shift/reboot or a restart/F1.

  OK, suppose that at some point in the future I need to access the BIOS (ex: changing boot options) and is not a job W10 or perhaps corruption W10.)

  How to enter BIOS without first W10? BIOS maybe consulted independent of the operating system?

  Hello and welcome,

  It is by design.  "Shutdown" in Win 10 more resembles the hibernation and it is not safe change hardware/BIOS setup in this State.

  F1/F12/ENTER should be available after a boot failure or a forced shutdown via a long press on the power button.

  BTW, UPDATE/restart and restart should just do the same thing. SHIFT button should cause a real stop after a followed Fx market should work.

  Z.

• BIOS HP Compaq Elite (i5-2400 CPU) 8280 cannot set the VT option

  BIOS HP Compaq Elite (i5-2400 CPU) 8280 cannot set the VT option

  found in the security system] [, thanks]

• Cannot enter Sleep Mode after undating for win7 / new BIOS

  Model: dv4 1435dx

  problem: cannot enter the mode 'sleep', when close the lids or click on 'sleep' without closing the lid, computer, enter the mode 'sleep' but immediately wake automatically. but it will not occur if the computer in mode sleep automatically

  So, don't know where the problem occurs, the first time I got Windows 7 update kit. It automatically update the BIOS of F43 to F44. then install windows 7. I don't remember if this problem occurred at this time. seems not at first, but after 1/2 weeks later

  can I update the BIOS to F61. problem still exist. then F65A. problem still exist.

  all other things are fine. No reset automatically. Hibernation is very good.

  So, I don't know if this is a bug in the latest version of the BIOS.

  In addition, update the driver from HP protect smart update of the window (I installed the driver from the website of HP, but windows update say there is a better driver)

  I wonder if it will be a problem too.

  Help, please. without "standby" mode, it is not good at all

  Oh, well, it's kinda stupid to answer the question myself...

  But I can't find the solution

  These guys have the same problem with me

  Just to go the device management, and then right click your mouse wireless, cancel the 'allow this device to wake your computer'... then problem solved.

  : bravohelen: