Cannot find enough available video memory when running GTA on Windows 7

Similar Questions

• Display card reader cannot find enough resources

  HI all - I volunteer administer laptops for a small school.  Last week a motherboard (not an Acer) fried, and a kid dropped her Acer crashed hard drive.  So I took the disk hard non-Acer, with his system and software always on this issue and put in the Acer laptop.  It starts OK and I installed some drivers from the Acer site.  However, I was not able to get the installed display adapter driver, and now the laptop is limited to the resolution 1024 x 768.

  The hard disk came from a computer with an AMD processor and an AMD/ATI video card.  The Acer computer has a processor Intel and Intel HD Graphics.  I ran the Intel driver installation program from the Acer site.  I tried "Uninstall" in the Device Manager display adapter and reinstall.  The only time where I had the Intel driver to install, its status was, "this device cannot find enough free resources that it can use.  (Code 12) "at the present time, sort the display adapter has been restored"Standard VGA Graphics Adapter", but even that cannot find enough free resources.

  I don't know if this is relevant, but following some advice I found in a forum, I tried to uninstall a couple of devices under system devices.  Specifically, even if I installed the Intel chipset drivers and I see them in the Device Manager, I still see two devices called "AMD PCI Express (3GIO) Filter Driver".  That cannot be good.  I tried to uninstall both, but the uninstall dialog box never ends.  I tried Mode without failure, but same result.  I tried to delete the referenced driver, AtiPcie.sys, but then the computer cannot start.

  Any ideas what I need to do to get the Intel driver work?

  Thank you!

  Bob

  Thanks philetus - I'm not back to school until last night.  I deleted all the system programs and all HP bloatware programs but no change.

  Of course I can't simply run factory recovery when the hard drive of the plant is dead and that the computer has a hard disk of another company.  But I'll just reimage the entire hard drive - I found an image of the entire system, I took a couple of years.

  Thank you all,

  Bob

• Satellite L300 - 29 X - device cannot find enough free resources

  I recently had to reinstall completely Windows Vista Home Premium, and before that, I was able to play games for example: World of Warcraft, Counterstrike Source;

  Since reinstalling Windows my display driver adapter doesn't work. It displays error "this device cannot find enough free resources that it can use. (Code 12) »
  And I m stuck trying to fix this problem. I tried some display drivers, but I think that I have I don't have the right one for my model.

  Thank you very much, Jessica

  Hello

  Microsoft says that this error message especially if two or more devices have been attributed, ports of entry/exit (e/s), the same interrupt, or the same Direct access channel in memory. The assignment was made by the basic input/output system (BIOS), the operating system, or a combination of both.
  This error message can also appear if the BIOS did not allocate enough resources for the device.

  To resolve this problem, you should go to Device Manager and should remove/uninstall the graphics card from the list of devices.
  Then, you should reboot the device and need to reinstall the driver of compatible graphics card.

  PS: Take a look at the BIOS. If a newer version is available and then try to update.

• HP Compaq 6910 p: 6910p "this device cannot find enough free resources that it can use. (Code 12) »

  Under hardware and Sound/devices and printers, I have a yellow triangle with my 6910p icon.  Right click on the "hardware" tab States "this device cannot find enough free resources that it can use. (Code 12).

  I've recently upgraded the operating system to Windows 7 Professional.  Everything works ok but I show this yellow triangle where the devices are displayed.  When I look in Device Manager/Mobile Intel (r) 965, I get a window saying 'Problem detected with Mobile Intel (r) 965 Express Chipset Family'.   The next window States: "the device cannot find enough free resources that it can use. (Code 12).  If you want to use this device, you have to disable other devices on the system once".

  How can I go about doing so, the yellow triangle disappears?

  I tried to reinstall device Base system SP46972 and SP45738 of the video driver.

  Not sure if this is related, but I also have a black screen with a 1 in. border on the left and the right, which was not the case when Windows XP is the operating system.  I also need to solve this problem as well.  Searches on Google did not find the solution, so I hope someone can provide the answers to these two questions.

  

  Glad to hear that you would have recommended as the next step.  It has proved to be a challenge, but one that we have managed to find solutions for.    Thanks again for all your help and patients.     Carl

• Out of memory when running only Firefox + flash

  Hello

  I am running Windows 7 on this computer. I'm only under Firefox (without Add-ons) that runs one leg with flash. The flash seems to be stifled because there is not enough free memory.

  According to the Windows Task Manager, Firefox uses 213 MB (size of validation is 240 MB). The flash player plugin uses 127 MB (size of validation is 217 MB).

  Yet, in the Windows Task Manager, I see the following for physical memory:

  • Total - 3327
  • Cache - 1419
  • Available - 1391
  • Free - 1

  I think the problem is that so much memory is cached, but I don't know. However, I think a machine with 4 GB of RAM should easily run a single tab with flash...

  Here are 2 screenshots that can help:

  • Physical memory
  • Process

  Can you help me with it? of course, it's very easy to reproduce.

  Thank you

  Erez

  Hey Erez,

  Do you experience out of memory when running Internet Explorer?

  If you are facing the issue only when you use Firefox, then I suggest you post in the Firefox forums.

  https://support.Mozilla.org/en-us/questions/new/desktop

  I hope this helps!

• Satellite Pro A300: code 12 - this device cannot find enough resources

  I use Vista Business 32 on my Toshiba Satellite Pro A300.

  Recently, I plugged my parallel to my laptop port adapter and the Device Manager, I had a device that said conflict error, "this device cannot find enough free resources that it can use. (Code 12).

  If you want to use this device, you will need to disable one of the other devices on this system. »

  Can anyone help me please with sorting on this problem?

  TEMI

  Hello

  This is a typical mistake if both devices have been attributed, ports of entry/exit (e/s), the same interrupt, or the same Direct access channel in memory.
  This error message can also appear if the BIOS did not allocate enough resources for the device.

  If seems that the resources are already used by another device, and so there is a conflict with the parallel port adapter that you have installed manually.

  I think you can only solve this check other devices that use the same resources and then that disabling in Device Manager.

• Code 12 Mobile Intel (r) Express Chipset Family 995 cannot find enough free resources that it can use. Must disable another device.

  I know what this means, but do not know how to fix it!  What other device safely disable to make this work?  Any help will be appreciated.  Thank you!

  See this:

  Code 12: This device cannot find enough free resources that it can use
  http://TechNet.Microsoft.com/en-us/library/cc732199 (v = ws.10) .aspx

  Try running the Fixit mentioned on the link under "additional information."

  If this does not work, try this:

  Go to Device Manager, under the display adapter, double-click on your Mobile Intel (r) Express Chipset Family 995 to see its properties. Click on the 'Resources' tab, under "Conflicting device list" note the device in conflict. Look for the device in Device Manager, if its listed under "other devices" right click and uninstall the device. Alternatively, you can "update driver software... ' or 'Disable' the device.

  See the links in the reference below:
  Resolve conflicts the Windows Device Manager
  http://support.verizonwireless.com/CLC/devices/Knowledge_base.html?ID=48051

  Troubleshooting of conflict of devices with Device Manager
  http://support.Microsoft.com/kb/310126

  Resolve hardware conflicts
  http://www.annoyances.org/exec/show/article07-003

• This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system (Code 12)

  Guys, I have a problem. So, my laptop has 2 graphics cards, an integrated course of the Intel HD graphics (which works perfectly) and the other being the dedicated Nvidia graphics (Nvidia GeForce 940 m). Until 2 days ago, everything was going well and running.

  I have the application experience GeForce and it prompted me that there is a new driver update should I download. He started to install then after rebooting to complete the installation, it failed. I checked my device manager and saw a yellow exclamation under under my Nvidia graphics card (remember, my laptop has two graphics cards: Nvidia graphics card and Intel HD graphics that works correctly). I immediately checked the details, and he said:

  "This device cannot find enough free resources that it can use. (Code 12) »

  "If you want to use this device, you will need to disable one of the other devices on this system."

  This seemed very strange, because it was LITERALLY working properly before I was invited about update driver I got, so I don't know what to do - as a matter of fact, literally, I finished this game, Deadpool, with my Nvidia card that I put as the default graphics card, a few hours before , so I don't know why this happened. Any help? I'm looking for a logical answer to this, guys!

  Additional information:

  A few days before this happened, I went to my store local pc and installed an extra 4 gigs of ram on my 4 existing to make 8. Don't know if it's useful, but anyway

  If I pick up my laptop and shake it side by side, I hear a slight rattling noise, and it seems a little loose (I found this out after seeing the error message). The noise seems to come from just below the middle of my keyboard (I'm using a laptop). If for some reason, my Nvidia card is loose? Is this possible?

  I am quite technologically inclined, but not to the extent of removing components and reconstruction cell phones / pc and access the bios and what not. I can only remove/add ram.

  I want to know if its something I am able to fix it because I do not necessarily want to go running and sending my laptop places - only my pc up shop.

  Here is the location of my Nvidia card: PCI Slot 4 (PCI bus 4, device 0, function 0)

  My specs:

  Acer TravelMate p257-MG

  Windows 7 business

  Intel core i5-5200u 2.20 GHz 2.20 Ghz processor

  8.00 GB of ram

  64-bit operating system

  1 t hard drive

  940 m Intel HD graphics 5500 & Nvidia Geforce card

  Just to recap, I get the error on my Nvidia graphics card code, "this device cannot find enough free resources that it can use. (Code 12) ""If you want to use this device, you will need to disable one of the other devices on this system. »

  Thanks in advance!

  Hello

  Thank you for your response.

  I appreciate your time.

  I suggest you run ' Intel Chipset Software Installation Utility ' and check.
  Reference:
  http://www.Intel.com/content/www/us/en/support/software/Chipset-Software/Intel-chipset-software-installation-utility.html

  Please keep us updated.

  Thank you

• PCI GBE Family Controller feature: ___This Windows 7 Ethernet Controller problem___Realtek cannot find enough free resources that it can use. (Code 12)

  My ethernet controller does not work since the installation of Windows 7 Edition home premium.

  Hello
  Code 12

  This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system. (Code 12)

  Cause

  This error can occur if two devices that are installed on your computer received the same i/o ports, the same interrupt, or the same Direct memory access channel (whether through BIOS, the operating system, or both). This error message can also appear if the BIOS did not allocate enough resources for the device.

  Recommended resolution

  You can use the Troubleshooting Wizard in Device Manager to determine where the conflict is, and then disable the device in conflict.

  Turn off the device in conflict

  1. In the device properties dialog box, click the general tab.
  2. Click troubleshoot to start the Troubleshooting Wizard . The wizard will ask a few simple questions and provides a solution to your problem, based on the answers you provide.
  3. Follow the resolution steps provided by the wizard to resolve the problem.

  If you want to say thanks to someone just click on Vote as useful (i.e. under each avatar of the user).

  If your issue is resolved, please indicate then your wire is with solution.

• This device (graphics card), cannot find enough free resources that it can use. (Code 12) __NetBook ASPIRE ONE - display adapter resource conflict?

  This device (graphics card), cannot find enough free resources that it can use. (Code 12)
  NetBook ASPIRE ONE - display adapter resource conflict? Can't find the other conflicting H-washer? Graphics Intel Graphic Media Accelerator 3150.
  If you want to use this device (graphics card), you will need to disable one of the other devices on this system. I bought this camera 6 weeks, I can't get the maximum. Set-up for my graphics cards. 800 x 600-32 bit only. Please tell me what to do. And ASPIRE or Windows7 customer service phone #. Thank you.

  Hi athe43,

  Below I've listed the details of error Code 12 and the article with additional information:

  Code 12

  This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system. (Code 12)

  Cause

  This error can occur if two devices that are installed on your computer received the same i/o ports, the same interrupt, or the same Direct memory access channel (whether through BIOS, the operating system, or both). This error message can also appear if the BIOS did not allocate enough resources for the device.

  Recommended resolution

  You can use the Troubleshooting Wizard in Device Manager to determine where the conflict is, and then disable the device in conflict.

  Turn off the device in conflict

  1. In the device properties dialog box, click the general tab.
  2. Click troubleshoot to start the Troubleshooting Wizard. The wizard will ask a few simple questions and provides a solution to your problem, based on the answers you provide.
  3. Follow the resolution steps provided by the wizard to resolve the problem.

  http://support.Microsoft.com/kb/310123

  This article was originally for XP however the description still applies.  Also, please see the following article on the opening of the troubleshooter of hardware for Windows 7:

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Hope that helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Code 12: This device cannot find enough free resources that it can use

  Original title: Please help me with this error   The device information

  Name: Intel G41 Express Chipset ID: PCI\VEN_8086 & DEV_2E32 & SUBSYS_2E321849 & REV_03\3 & 11583659 & 0 & 10 Error code: 12

  Hi RoseLover,

  ·         How long have you been faced with this problem?

  ·         You did it last changes before the show?

  Error code 12:

  This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system. (Code 12)

  Cause:

  This error can occur if two devices that are installed on your computer received the same i/o ports, the same interrupt, or the same Direct memory access channel (whether through BIOS, the operating system, or both). This error message can also appear if the BIOS did not allocate enough resources for the device.

  I suggest you download the latest drivers for the graphics drivers on the Intel site and see if the problem is resolved. Check the links below.

  http://www.Intel.com/support/chipsets/sb/CS-022768.htm

  http://www.Intel.com/support/graphics/detect.htm

  Apart from that, I suggest you to refer the below link.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps!

• Removed USB controllers: can not return - "this device cannot find enough free resources that it can use. (Code 12)

  Original title: removed USB controllers: can not return

  Hello

  So today I tried to connect to a printer, and it wouldn't work (separate the issue, I don't want to worry about that now)

  I've seen several messages saying: you need to uninstall the USB controllers in Device Manager and then restart your PC. The pilots would then automatically reinstalled.

  It didn't happen, and now my Dell touch screen does not work. I can miss several other USB controllers too, I uninstalled about 3 of them, but I don't know whether or not it has been reinstalled.

  I currently have:

  -Hub USB generic

  -Enhanced host controller USB Intel (R) 8 series #1-9C 26

  -USB root hub

  -Host controller compatible xHCI USB

  Note that the last of them was a symbol of error on it and reads as follows:

  "This device cannot find enough free resources that it can use. (Code 12)

  If you want to use this device, you will need to disable one of the other devices on this system. »

  Can someone please tell me how much USB controllers I should have and how to save them?

  Thank you very much

  Hi Shalini.

  Thanks for the reply, but if you read through the posts on this thread, I think you will find that it has already been suggested that I do these two things - what I've done many times without result.

  Fortunately, I managed to fix it myself.

  To satisfy your curiosity and help someone else who could see this thread with a similar problem, here are the steps I took finally solve the problem:

  ______________________________________________

  I was always convinced that the problem is basically with the xHCI USB controller that I saw always reported as not working not properly in the device (Code 12) Manager. With this in mind, I set out to see if I could determine what the device was supposed to be in conflict with. I ran msinfo32 and began to examine the conflicts/sharing section. After a while, I decided I could not see anything obviously problematic or direct me to the controller xHCI, so I gave up on that front.

  Well, if I couldn't fix the problem with the current installation, maybe that I could find another way to install the xHCI USB controller that could circumvent the flaw that seems to be caused when windows reinstalls automatically it when restarting after the abduction. So I started trying to learn more about this "xHCI USB controller" - since Googling this term has given no end of problems not related.

  In Device Manager, I found a way to isolate the details of this driver in device (somewhere under the properties I believe) Manager. This has created a custom device showing in view only a select few connects the Manager. I have spent some time in the analysis of these and found the time during which the camera has stopped working properly. Suddenly a pattern emerges. Over and over again, see you the following series of when I was hoping that allowing windows to reinstall automatically the driver would to fix:
  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 has been removed

  [Rebooted PC]

  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 has been configured
  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 had a problem starting.

  Under each newspaper was referring to a driver name, I didn't already had access to: driver name: usbxhci.inf

  Now I got some new information about the xHCI USB controller, I took to Google. After much research (and not find something relevant), I found 2 obscure references to the driver who seemed at least somewhat relevant.
  The first reference has been a post on the forum where someone's USB ports stopped working. very similar problem to mine! There is little of any particular use in the nets, with the exception of the reference to a couple of windows updates: KB 2823516 or KB2822241

  It is not clear exactly what usbxhci.inf capacity was tied to these updates, but I made a note of them and moved.

  Another article contained no mention of specific ports USB not working does not and was centered around a different problem entirely. However, he has mentioned an another windows update: KB2919355-x 64.msu

  This one (as I remember) was clearer on the relationship between the update and changes to the usbxhci.inf file.

  Now, I had three updates which could make changes to usbxhci.inf at one point. With their name on a piece of paper, I started looking through my updates installed to see which ones I had installed. I soon discovered that Ko 2823516 or KB2822241 were not present on my PC, which saved the penalty to guess who would be the right to uninstall first.

  KB2919355 has been installed, and I made the decision to uninstall it, because as far as I knew, this update changed something in usbxhci.inf. After the initial uninstall was completed, but before the mandatory reboot for changes to take effect, I went into Device Manager and removed the xHCI USB... because I was afraid that if the new, "defective" was always present during the reinstallation of the update, it doesn't change anything.

  The device is removed once more, I rebooted the system. He drives for a considerable period, uninstall the update and then seems to have some sort of hitch; declare something in the sense of "we could not complete the operation. Changes to undo. " He stayed like that for a while before the system became operational again and began to "prepare windows. Once it was over, I discovered that my touchscreen and USB ports worked very well.

  Investigation later showed that the compatible USB xHCI host controller was is no longer marked with warnings. In addition, a series of USB controllers appeared that had not been there when the xHCI device was defective. I was also pleased to note that the update of windows for KB2919355 had already been reinstalled without messing up anything.

  _________________________________________________

• Satellite L300-19Y: problem GPU - device cannot find enough free luipermettant

  I have an error message on my display Adaper stating,

  «The device cannot find enough free luipermettant it can use (code12).»
  If you want this device, you will need to disable one of the other devices on the system. »

  It is a Satellite L300-19Y with graphics Mobile intel 4. I have updated to the latest version of the driver.

  The screen is very blurry at the moment.

  Please help with a solution if possible.

  Hello

  I found your other thread:
  http://forums.computers.Toshiba-Europe.com/forums/message.jspa?MessageID=250126

  You tried to install an ATI driver on this laptop.
  I don't know if this would affect the functionality of the OS, but it seems that you get an error message during the installation of the Intel driver, then perhaps you have confused the OS installed some drivers wrong

  Have you used the driver from the Toshiba driver page?
  If this isn't it!

  You must first uninstall the driver in Device Manager and then reboot the laptop.
  After the new reboot, you should check if you could install the driver once more

• AMOUNT OF AVAILABLE VIDEO MEMORY

  Total available video memory of my pc is 4096 MB. Can I use this memory to 4096 mb graphics card? As 4096 MB of total available video memory and video memory 4096 MB dedicated, 0 MB memory shared system, my system memory is 16 GB memory DDR3...

  Help, please... THANKS IN ADVANCE...

  I'm not sure what you're asking here, but I take a stab at the answer. The amount of memory used by a graphics card is highly dependent on what is on your screen resolution and color depth is either 16-bit against against 32-bit 24 bit. It also depends on if you use the second video port in a dual display configuration or not. The GPU on your map to determine how much memory it needs up to a maximum of the amount of what the card can support. After that, it becomes a compromise usually in the amount of colors that can be displayed at a given resolution.

• Can I use command "run as" when running programs in Windows XP by using a limited account

  Original title: I wonder y at - it means to

  is there way to do (run as) window appears automatically by clicking on the program while you are on a limited XP account

  Hi mohammadnagdy,
   
  I'm afraid to inform you that this option could not be activated with the standard user account.
   
  You must log on to an administrator account to perform this question.
   
  How do I activate and use the command "run as" when running programs in Windows