Cannot find the network driver

Hardward Ids:

PCI\VEN_10EC & DEV_8136 & SUBSYS_2AB7103C & REV_05

PCI\VEN_10EC & DEV_8136 & SUBSYS_2AB7103C

PCI\VEN_10EC & DEV_8136 & CC_020000

PCI\VEN_10EC & DEV_8136 & CC_0200

HP slimline E5000

s5716f

Windows 7 ultimate 32 bit

Installed several drivers failed

Help, please

Hello

You have problems because of the drivers didn't like these drivers belong to Eathernet port

You can connect your Internet if not fallow the steps

1. go to Device Manager and uninstall and reinstall the driver for the network card

2. after having what its still the same try doing system recovery fom F11

3. always if it's the same problem the motherboard needs to be replaced because the port net eather is part of the motherboard

Thank you & Regarsd
Dinesh Kumar
* Click on the thumb BRAVO upwards on the left say "thank you."

Tags: HP Desktops

Similar Questions

  • My computer has virus of the FBI, I wiped it is clean but now it cannot connect to intermet because it can't find the network driver how can I find it?

    My computer has virus of the FBI, I wiped it is clean but now it cannot connect to intermet because it can't find the network driver how can I find it?

    Since you have formatted the PC and reinstalled Windows, your question will be handled better in the hardware forum space and drivers for Windows 7, so I'll move it there.

    Apparently, you need to install the driver of your PC network. If you used the CD to restore the PC manufacturer that should have been included, but it may be on a 2nd CD with drivers and programs.

    If not, the first thing to do is contact the PC manufacturer to see if they have a driver available for download. If the PC has a wireless network card and wired, perhaps one has been configured, but not the other and you try to use the not yet detected and installed.

    -steve

  • When I perform a net view on, I get the error system error 51 next. Windows cannot find the network path.

    Net 51 with a view system error

    I have two boxes of Windows XP that I login as administrator account. I was able to synchronize files, map network drives and can do a tracert to reach one of them.

    However, when I perform a net view on, I get the following error

    51 system error has occurred.

    Windows cannot find the network path. Make sure the network path is correct and the destination computer is not busy or turned off the coast. If Windows still can't find the network path, contact your network administrator.

    How to make this command work?

    Hello

    ·         Your computer is on a domain network?

    Follow the steps in troubleshooting this article and check if that helps:

    You cannot access shared files and folders or browse computers in the workgroup with Windows XP

    http://support.Microsoft.com/kb/318030

    See also this article that resembles the same error.

    Error when you try to access shared resources on a computer that is running Windows 2000 or Windows Server 2003: "53 system error has occurred" or "51 system error has occurred."

    http://support.Microsoft.com/kb/259878

  • Epson Event Manager cannot find the scanner driver. Epson said that the event handler is a windows thing, and so is the problem.

    I installed an Epson Stylus SX215. I can print, scan and copy if I use another way, but if I want to use the event handler it says that it cannot find the scanner driver may not use the event handler at all (cannot yet open the program).
    In addition, the scan option "attached to electronic mail" does nothing either. Don't know if this is because the event handler program or because he can not see e-mail programs I have.

    Hi bdelrio,

    Thanks for posting. Try running a System File Checker to find errors.

    Click Start.
    In the search box type cmd
    In the menu start right click on cmd.exe and select Run - As-Administrator.
    In the command prompt, type "sfc/scannow".
    Allow this to fill and run. Please let us know if this corrects and error, or if it reports errors, it cannot fix.

    Thank you! Shawn - Support Engineer - MCP, MCDST
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think

  • Mac OS 10.5 Hello cannot find the printer driver for P1606dn connected via a wired network.

    I tried to connect my HP Laserjet Pro P1606dn to my PowerMac G5 running Mac OS 10.5.8.  I have connected the priner to my LAN via the Ethernet cables and Switch 8 port NetGear.  I then properly installed printer driver from the CD provided on the Mac and went into system preferences / Print & Fax to add the printer to the list of the connected printers.  Click on the button «+»  The HP P106dn was listed in the table (kind = Hello).

    I chose this entry in the table, and the dialog box immediately went into action: the pullodwn "to Print using" listed the message 'Please select a printer or driver model' greyed and a spinning wheel called 'Search for new drivers' appeared underneath.  The dialog box search but never find the printer driver (I waited for 20 minutes without success).  I installed some other HP printers in this way on this machine with no problems, for example, HP Color Laserjet 2605dn.  Why this method does not work with this printer?

    I was able to connect to this printer with other (Intel) Macs in my house through this arrangement of LAN.  Is the printer driver for the Intel Macs only?

    I disconnected the printer from the local network and connected directly to my Mac with a USB cable.  The same process, and I was able to connect to this printer.  Successfully print a document page.  Although it gives me a work-around for Mac G5, I need to share this printer with other Macs in my household.

    I went on the HP download site and downloaded the latest driver for this printer, re-installed the printer driver on Mac and repeat the steps for the arrangement of LAN (above) complete the connection via the Print & Fax dialog box.  The result was the same: spinning wheel looking for a printer driver are not.

    I don't know what else to do, or why this facility will not work.  I would much appreciate it if someone could give an explanation for this or any suggestions as to what can be done?

    Ed

    I'm sorry to get back to you on this so late.  I was OOT Sunday all day.

    Ok. So, here is what happened.  As I mentioned at the end of my last post, I was in the process of resetting my printing system, repair disk permissions, then restarting.   Reset the printing system wiped out all my printers in the "Printers" pane in the "Print & Fax" system preferences dialog window  I moved forward and fix permissions of the drive on my system disk.  A number of authorities have been repaired, but nothing that I could decipher impression related ro.  Finally, I restarted my Mac and went directly to the dialog box print & Telec.

    As the printers pane was still empty, I'm gone before adding the simplest of my printers (LaserWriter 360 connected via AppleTalk) who has always been correctly added to the list printers in the past.  No chance!  WAITED a few minutes everything is was "Looking for new drivers.".  I tried the Color Laserjet 2605dn.  No luck.  Then the Laserjet P1606dn.  No luck.

    Thus, this way of solution did not work, and now I was without any driver associated with one of my connected printers.  I decided that I had no choice to rebuild the operating system.  I started my DVD of Installation OS 10.5.4 to rebuild my system (without reformatting my HARD drive).  Once which was finished, I've immediately went to the Print & Fax dialog box and tried to add in each of my printers.  In a few seconds the LaserWriter was added successfully, then the HP Color Laserjet 2605dn, and FINALLY, the Laserjet P1606dn.  Thus, it appeared that my upgrade to OS 10.5.8 was at the origin of the problem.

    I proceed with Sofware Update to restore the computer to OS 10.5.8 and again once, went to the dialog box Print & Fax to experiment with the addition of each of the printers again.  Stopping before the acceptance of each 'Add', I could find quickly and successfully the drivers for each of the connected printers.  So, it doesn't seem to be a problem with OS 10.5.8 find printer drivers.

    After reflection, I concluded that the problem must have appeared during the upgrade to OS 10.4.11 OS 10.5.4, but it remained hidden until I tried to add these new printers to the list of printers.

    I appreciate the reference to the last download Laserjet full feature software.   Since I was able to solve the problem without it, I mind not do the download.

    I want to thank you for patiently stay with me during the last two weeks, your advice and comments.  Just having someone to "talk" about it, it was reassuring and useful that I went along to apply each suggestion to the problem.  I tried to solve this problem several times on my own before that, the search of the forums, and I hesitated to participate actively – to reach out.  I'm feeling very different about it now.  Once again, thanks a lot.

  • Satellite L305D S5895: Win 7 cannot find the HARD drive or cannot format the HARD drive on a clean install

    I have laptop Satellite L305D S5895 of the customer. It was delivered to me by the customer who tried to install Windows XP Pro, Vista and none would install.
    He said he tried all the CD that he had finally dropped on it and delivered it to me installation.

    When I got the score have been removed, so I tried to install Win 7 and when I do a custom install, I get an error indicating that the hard drive can not be formatted on disk 0 or it will give an error that no hard drives have been found.

    I have reset the bios default and no matter what I do, it won't format or find the hard drive. I was going to upgrade the bios, but the only way I found to upgrade the bios is once windows is installed.

    Everyone has ideas about this laptop so I can get a system installed. I checked the bios and there is no parameters for a sata, raid or IDE disk drive, so it seems that this version cannot be changed.

    Thanks for anyone who can help you.

    Rick

    Hello

    First of all it is an American notebook series.
    [Satellite L305D-S5895 | http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/modelContent.jsp?ct=DL&os=&category=&moid=2144776& rpn = PSLC0U & modelFilter = L305D-S5895 & SelCategorie = 3 & selFamily = 1073768663]

    The laptop supports a processor AMD and ATI chipset.
    This means that the drivers SATA is part of the ATI graphics card driver.

    You must include the first SATA driver in order to install the Windows operating system.
    You could add the SATA driver for the Windows disk using software like nLite / vLite

    Welcome them

  • Cannot find my network driver

    I tried a few drivers, but none work. I just installed Windows XP Professional and I have a gigabyte motherboard 32-bit. I am looking for the network driver in order to install the other drivers (Video & Sound Drivers) and browse the Internet. Can someone please help me find it. FYI... I built the PC myself, but I can't find the driver... Thank you!!

    Do not install any driver. Go to the Gigabyte website, look for the model. And download / install. First install the chipset drivers

  • 4400 Workstation XW - cannot find the graphics driver

    Paul Tikkanen advised me to ask here for help about this problem.

    The pc is a Workstation XW 4400 (PW375ET), with Windows XP SP3 and the .net framework 4.0 installed (I don't know if it's relevant). There are some old looking for graphics card plugged into the motherboard with the name written on it of MATROX (Paul says it's a Matrox G200 according to the ID of the hardware) but this ("this Setup program does not detect a supported by this software Matrox graphics card') or all the other drivers that I found do not work.

    Is the hardware id

    PCI\VEN_102B & DEV_2538 & SUBSYS_0947102B & REV_02

    Maybe someone here can help.

    with sincere friendships.

    Naim Saari

    Helsinki, Finland

    Googling "PCI\VEN_102B & DEV_2538 & SUBSYS_0947102B & REV_02" gave a few sites and after a minutes to read (but not to download anything I have concerns on part 3 pilot sites), I found that the card is a Matrox Parheila AVPe.

    Googling "Matrox Parheila AVP" is the Matrox product to this map page. After a few minutes navagating on this site, you can find the XP driver for this card. There are 3 of them, but the last driver HF dated May 8, 2007 is probably the right to choose, it is the 1.13.00.158 HF version and supports XP and VISTA.

    To obtain the driver, start http://www.matrox.com/graphics/en/products/legacy/parhelia/parheliaapve/ , and then click Driver and software in the left pane. Click on Parhelia Series then check Parhelia APVe and press Next. Click Next and drivers of Windows XP (or the required operating system), and then click Next. This should give you the necessary driver selection page and it should be obvious what to do next...

    But note the message on the download page of the driver on the removal of the old driver before you install the new driver...

  • Satellite L300D - cannot find the XP driver for the graphics card

    Hello

    I just bought a Toshiba Satellite L300D and I installed Windows XP (instead of vista, which was preinstalled). I can't find the XP driver for the graphics card... Everest recognizes him as ATI RS690M. A download link will send me straight to heaven!

    Thank you in advance,

    Nikos

    PS. of course, I searched the display on the sites of several Toshiba driver and I got this message: "the resource you are looking for has been removed, had its name changed, or is temporarily unavailable."

    After that, I tried the driver from ATI, and it seems that they are more home driver for XP.

  • Satellite A200 cannot find the storage driver

    I have a laptop satellite A200 and everytime I restart the computer, it can not find the ' armazenamento driver of massa "in English, I guess it's"storage driver.

    We can I find it?

    > it can not find the ' armazenamento driver of massa "in English, I guess it's"storage driver.

    Go to the page of the Toshiba driver and download, storage manager,.

    http://EU.computers.Toshiba-Europe.c...ivers_bios.jsp

  • Cannot access the network drive or impossible to mount the network drive. Error "network path was not found.

    Original title: network path was not found

    HI, after the upgradation from windows xp sp2 to sp3 (next to the customer) I can't access the network drive or impossible to mount the network drive. ' ' It showa error "network path was not found.

    Hi gauravadavadkar,

    Thanks for posting your query in Microsoft Communities. Provide the following information:

    ·         Did you do changes on the computer before the show?

    ·         What is the full error message?

    ·         Work on a domain?

    Follow these methods.

    Method 1: Temporarily disable the security software.

    Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

    Method 2: Follow these steps:

    Step 1: Start the computer in safe mode with networkand check if the problem persists.

    S tep 2: if the problem does not persist in safe mode with networking, perform a clean bootto see if there is a software conflict as the clean boot helps eliminate software conflicts.

    Note: After completing the steps in the clean boot troubleshooting, follow the steps to configure Windows to use a Normal startup state section of the article to start the computer to a Normal startupmode.

    After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

    (a) click Startand then click run.

    (b) type msconfigand click OK.
    The System Configuration utility dialog box appears.

    (c) click on the general tab, click Normal Startup - load all device drivers and services, and then click OK.

    (d) when you are prompted, click restart to restart the computer.

    Method 3: Follow the steps in the article.

    How to troubleshoot a network home in Windows XP

    In Windows network connection issues

    You can read this article for more information:

    Windows wireless and wired network connection problems

    I hope this helps. Let us know if you need more assistance.

    Thank you.

  • The installation of XP Pro cannot find the hard drive

    The machine is running XP Pro 32-bit, and I am "upgrading" to 64-bit to work with AutoCAD.  When I boot on the 64-bit Setup installation CD can not find the hard drive and the demolitions.  The drive is already formatted to NTFS.

    You try to install on a SATA drive or your disks are on an add-in controller card and the Windows XP Installer x 64 doesn't have the required driver for the controller so it can't detect the drive.

    You have three options:

    1 - Use the F6 method to provide the installer for Windows XP x 64 mass storage drivers.  Drivers MUST be provided on a floppy disk, the Setup program will not accept the drivers from other media sources.

    2 - enter your CD of Windows XP x 64 drivers.  Note you will find reference to SP3 slipstreaming your Windows CD which you can install Windows on a SATA drive, but please note that Windows XP x 64 doesn't have a SP3, SP2 is the latest service pack for Windows XP x 64.

    3 (for the integrated SATA controllers) go into the BIOS and put the controller in IDE, most motherboard with SATA controllers mode on Board have an option to do this.  When mode IDE Windows XP Setup will see the drive and you will be able to install Windows.  Once Windows is installed, you will be able to install the SATA drivers from the installation of Windows XP operational.  You install the SATA drivers before changing the SATA mode controller in the BIOS, or when the Windows boot up upward a BSOD with a 0x7b error.

    John

  • HP2000 2D09SLA, cannot find the network controller driver after reclassification of win8 base to win8pro

    HP2000 2D09SLA, PROFESSIONAL 64 BITS OF WINDOWS 8.

    After installing windows8pro, I could not find driver for network controller, since then I can not use my wireless.

    Hello:

    Follow these steps, and I'll post the link to the wireless driver you need...

    Go to Device Manager, find the other devices category, click the network controller needing drivers.

    Then click on the Details tab at the top of the control of the network window.

    Now, you see a drop-down list of property and it is set by default to the Description of the unit.

    Drop down on it and select the second item in the list (Hardware ID).

    After the first string of characters that start with PCI\VEN.

  • Cannot index the network drive...?

    I was I big bear to Microsoft for 20 years now, but have something as simple as a network drive index terms (including XP and Vista was quite capable of) that now available in W7 is not a shame...
    I can understand if you can add to a library, but you can't make even the indexing of files network.  You must make it available offline, which is not what I want, need and highly impractical replication 500 GB on my laptop of 300 GB.  In addition, don't want these files on my laptop for security issues.  Let us, index or add it to a library Windows can help you to find us our data instead of trying to force us into a way to data management that is not practical.
    Windows 7 is very quickly becoming a larger more flexible maturity of Microsoft ' we wan to control the way that you do things "attitude.  From a functional point of view, it seems stable, but Microsoft's vaunted now "calculate and store the data of your way" in advertisements that I clearly know be set to FALSE.
    In addition to all the people questions W7 installation and delivery are affected by, you managed to turn IE into the bloat-ware. On my laptop Windows 7 freshly installed with 3.0 Ghz and 4 GB of memory, it takes 4 seconds for IE open.  Firefox, Opera, Chrome all start and ready to go the second.  Installation of Windows 7, which cannot perform an "upgrade" on the key issue of product own drive hard, or without the help of sellers of shit like Digital River.   I don't understand why Microsoft is going in this friendly way extremely lay to make things very awkward and difficult for its customers.
    Microsoft has managed to alienate their power-user and technical groups by the infantilization of the things down and removing some key features. Not too sure about the reason of this business like the OS market is about to get highly saturated and competitive... so lets to alienate our power users, those who innovate push us Microsoft into the business and residential community to make IE slow and cumbersome.

    Maybe these Mac ads aren't too far from the truth...

    Hi KipperMN,

    Thank you for using Microsoft Answers!
    Take a look at this thread below, it can provide some ideas on how to bypass the indexing network drive:
    If Internet Explorer takes a long time to open because of the "bloat-ware", have you tried Internet Explorer with no modules?
    To do this, click Start , and then type Internet Explorer. In the results, you should see Internet Explorer (No Add-ons).
    Often what I saw is the first time that IE opens, it may take a second or 2 longer than usual. But every time after that (because it is loaded into memory), it is very fast to open. Also, take a look at the following thread: http://social.answers.microsoft.com/Forums/en-US/InternetExplorer/thread/72dd379e-bb28-4342-91ec-472d9af83ab7
    You're talking about Windows 7 "withdrawal of some key features. Is there something specific that you don't see?
    Overall, I'm sorry that you have had a bad experience with Windows 7. As Steve says, giving feedback is the best way to improve Windows.
    Let me know if I can do anything else for you help!

    Cody C
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Cannot find the display driver just after the replacement of the GPU on Satellite P200

    I got my laptop yesterday to SAV, because my graphics card has been damaged.

    Now I can start Notepad, but in the hardware Manager is only an entry for the VGA, the new map, which should be in the notebook, the Manager cannot be found.

    I tried to find it with the plug-and-play, but with no result.
    The system is only VGA... After that I tried with a catalytic ATI 8.9 driver. But after installing it do not work too (I restarted the NB)

    May I use the wrong driver from ATI, but I can't find an entry for Mobility Radeon HD 2600.
    Only Radeon 2600 Hd. I'm not sure; This driver also works for mobility?

    Can you give me a link to the correct driver?

    Hello

    First of all, it would be interesting to know what series of laptop you have.
    Then you are sure that another graphics chip has been used?
    Are you sure that it is a Mobility Radeon 2600 HD graphics card?

    If you are not 100% sure I would recommend contact the technician who changed the GPU and seek clarification; What GPU chip has been used and where to find the driver.

    I'd appreciate some feedback from you!

Maybe you are looking for

  • No apps on iTunes Apps Resumepage

    No apps to appear on the summary page V9.3.2 Apps iTunes with my iPhone connected and synchronized to the top 6s.  I can see the screens of iPhone OK on the right side of iTunes but no show of Apps on the left side.  Running on my new iMac OS X 10.11

  • Tecra M5 - Internet explorer "hangs".

    Sometimes when web pages loading my internet just hangs - and load in a few seconds, but it can do several times a day, doesn't seem to matter what I loaded, it happens even with Google page. Anyone have any ideas why or how I can stop it? Thank you

  • DeskJet F4280 scan does not

    I lost my CD installation disc, when I run the wizard for help, he asks insert me this disc I did not.  I can print with the printer.

  • Lenovo IdeaPad Y400 evolution Options

    Hello I plan to buy a Lenovo IdeaPad Y400 in the coming days. The shop I bought it from has the following characteristics: i7-3630QM -Windows 8 -8 GB DDR3 1600 MHz RAM -1 TB SATA HDD (5400 RPM) Modular DVD drive -NVIDIA GeForce GT 650M 2 GB GDDR5 I n

  • HP Z6000: Z6000 middle mouse click?

    I just bought the Z6000 on liquidation of stocks, and it's a thin mouse with one button and a capacitive touch sensor. (HP, have you been hanging out with Apple?)Is there an official way to get a middle on the Z6000 click? (I suspect that the answer