Cannot find the partition recovery on the Satellite A200-1BP


First of all, I have a Vista Home Premium 1BP A200 and I lost the product recovery disc and I want to create one with "Recdisc.exe" product of Toshiba Recovery Disc Creator or Vista.

They both failed because I didn't get a message "No disk HARD recovery Area!", then I looked in the "Disk management" section and could not find any partition without a name.

There were two primary Partition which were 1.46 GB 'in good condition (EISA Configuration)"and my Vista (c).
So, what should I do? Can I create a recovery partition?
Or can I set the Recovery Disc Creator? (v.

PS: I got my computer several times with my CD, which probably used my recovery partition.
Seriously, I'm out of ideas and I don't want to lose 50 dollars just to get another copy of disc PR.

PS2: I used press '0' and 'F8' thing too, they no longer work.
Is there a way I can restore without any disk?

Post edited by: darthbabam12


> There are two primary Partition which were 1.46 GB 'in good condition (EISA Configuration)"and my Vista (c).
> So what do I do? Can I create a recovery partition?
> Where can I solve the Recovery Disc Creator? (v.

It seems that the recovery of HARD drive partition is missing
The first 1.46 GB partition is automatically created by Vista and the C partition is the system partition, the partition of HARD drive recovery doesn't seem to be available

> PS: I got my computer several times with my CD, which probably used my recovery partition.
Retrieve you the Vista using the recovery disc or what drive did you use?

If you have installed the system using Microsoft Vista disk then, it was a big mistake because it deleted the partition of HARD drive

> Is there a way I can restore without any disk?
Either you use a Vista MS disk and missing drivers, which you can download from the Toshiba page or you order the Toshiba Recovery disk don't see another solution

Tags: Toshiba

Similar Questions

  • Cannot find the Satellite L650 - 10 H in the support database


    I bought Toshiba L650 - 10 H (PSK1JE-00400MSK) two years ago and now I have problem finding this model in support of database.

    It's my laptop:


    This laptop Satellite L650 - 10G is the MODEL DISCONTINUE

    You can find the data sheet here:
    [Satellite L650 - 10G: true & com decided .new .broadvision = Yes & PRODUCT_ID = 10 85933]

    If you need drivers, you can download this driver page

  • Cannot retrieve the Satellite A200-1RK - error: 18121 COMPONENTS. SAV


    This is it, I got a laptop TOSHIBA Satellite A200-1RK for only less than a year and currently just started to experience problems in this regard.
    So I decided to restore the computer to factory settings using the recovery disk supplied with the notebook. After that the following instructions which recommended that the process started to get succesfull until after 100% invites it commond came suddenly with the following error:

    [Error: 18121 C:\Windows\System32\config\COMPONENTS.] SAV

    Error image restoration.

    The specified image file did not contain a resource section.

    ERROR: ImageX could not apply VISTA E:\05241XP.swm Index 2 weird to C:\.
    Press a key to continue...

    Then, when I press a key, it remains on a white screen and with TOSHIBA down right and don't turn...
    Then I restarted using the power one button came the following:

    Windows could not start.
    A recent hardware change followed by instructions to use the vista DVD and recover the PC using that...

    Help would be greatly appreicated as the laptop does not work... Thanks in advance...


    Hmm strange I have never seen anything like it.
    But according to the error message that imagex could not apply VISTA E:\05241XP.swm Index 2 of ODD to C:\ there was a problem copying some files from E to C (from HARD disc to disc).

    Have you tried to boot from the recovery again disk? If this isn't the case, then try it!

    If you will not be able to restart the laptop using the Toshiba Recovery then disk you should check if it s possible to boot from the other bootable discs like Win XP or similar.

    But if none of these disks will work then a hardware problem is possible. In this case I recommend you first HARD drive.

    Good luck

  • Other bluetooth devices cannot see the Satellite A200-psae63

    Hi all.

    I have laptop Toshiba Satellite A200-psae63 and the following problem:
    I installed the new driver for bluetooth for my model, bluetooth monitor 3. In bluetooth settings I put that other bluetooth devices can see computer.

    But they do not.
    They only see it when I click the file recevi on my bluetooth icon in the status bar.

    I tried to reinstall the driver again, but the problem is the same.

    Can someone help me?


    Please note that you will need to install the BT stack too and not only BT monitor.
    In addition, don't forget that your BT is activated by pressing the FN + F8 key

    See you soon

  • Vista cannot find the mouse USB - Satellite P100 - 434 PSPADE driver

    * Need help to install a mouse optical usb on vista32 *.

    I have two mice, two optical usb, 1 wired and 1 wireless. They are the two plug-and-play so when to plug their vista must locate and install the right drivers automatically... it can't.
    Vista search drivers on the disk and hard on the internet.

    "" looking software... looking for an online software.. "."

    Then says:
    "Windows encountered a problem installing the software driver for your device."
    Windows found driver software for your device but encountered an error trying to install it.
    USB Human Interface Device
    The system cannot find the specified file. »

    They are plug-and-play and just install automatically, there is no driver CD that come with the mouse.

    I have a Toshiba Satellite PSPADE P100-434 with Vista 32 bit purchsed new 2 weeks ago.

    Help, please... Thank you!

    It's strange, because the standard optical mouse should be installed without time and without the need of specific drivers.
    Did you check the homepage of the manufacturer for drivers?

    And have you installed all the latest updates for microsoft windows and SP1?

  • Satellite T110-11U - cannot find the router WLAN


    I have a Toshiba Satellite T110-11U. Have had since February and loved it-fortunately it wireless used throughout the House. Then one day on a month, unless I was in the same room that the wireless router, Wireless does not work. I have 2 other laptops (and iPhone) which still connect wirelessly throughout the House and the garden without problem.
    As you can imagine, it was very strange. When I take in the garden, my other laptops are all networks wireless in the region, but my Toshiba can't find any.

    Suspecting it was a driver problem, I made sure that the wireless drivers are up-to-date. With no joy, I got the system as it was at the time of purchase (do a complete restoration by interupting, starting and leaving the hard drive to be deleted and reinstalled etc.). Still the same problem. I even changed the rooms in which the router is, and the same problem - the Toshiba cannot find the router unless the router is located a few meters from the laptop.

    Until I lose the will to live, can anyone suggest the cause of my problems, or is it time I admitted defeat and brought back to the Comet under warranty (where likely test next to a wireless router and tell me everything is fine!).

    Thank you very much


    Hey Buddy,

    Did you check if the wireless network card is recognized correctly in the Device Manager? There may be a yellow exclamation or unknown device. Try also updating the driver WLAN from Toshiba Web site:

    See all other WLAN routers?
    The wireless network card can be activated using a combination of keys FN + F8 and in the BIOS. In the BIOS, you should also load default settings and test again.

  • Ran repair and now recovery cannot find the OS to fix it.

    Damaged operating system.  Ran repair and now recovery cannot find the OS to fix it.  When I try the installation option, I get an error message that it can't find install.wim.  Operating system has been installed on a HP Pavilion a6600f and I have the product key, just not Vista 64 bit to enable more.

    * original title - corrupt OS. Ran repair and now recovery cannot find the OS to fix it. When I try the option to install I get an error message that it cannot locate install.wim*

    Hi agc409,

    Please see the following HP Web site:

    I hope this helps!

    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think

  • Win 7 Pro, FX6100, 8 GB of ram, 250 GB ssd; cannot find the system partition

    Basics are there.  It blocks from the tent to set up partitions.  I am giving all of the 250 GB SSD to use as seems it and it is just lost.  It does work with no partitions, partition of the entire disk.  He didn't tell me what he wants.  And error messages make no sense.

    They are like: (and my response)

    cannot find the system partition (do a stupid)
    Can not find the installation partition (crikey, I gave you the entire disk, make one)

    Talk about mega-frustration.  How about a useful error message and some useful ways to respond.


    If the ssd is not recognized in the first part of the installation process, as a location to install win on, you need to check the manual of the card mother about all the necessary bios for its port settings, or weather, you need to install any third-party disk controller.

    And if it's a new ssd, must not contain any partition table, unless you have prepared this ssd when you started in one of your other installations win, that can be part of your problem.

  • ESXi 4.0 Dell T105 "cannot find the boot partition.

    Dban Nuke used to wipe my hard drives (two of them).

    Unplugged the secondary hard drive.

    Installed ESXi 4.0 (declared success).

    Machine starts, starts in ESXi 4.0, starts to load, then:

    "Cannot find the boot partition.

    Others have suggested to set parameter SATA AHCI controller. Not possible in my BIOS. I 'ATA Mode' and 'Off '. "Off" turns off the entire controller and my hard drive is not recognized.

    Others still suggested to install on a USB key. Wary of such a hack...

    Help, please. There is very little out there on ESXi 4. Even a pointer to VMware documentation with a list of error messages and their meaning/solutions would be helpful (unable to find such a list myself).

    I had the same problem that others are with the start-up for the drives. I went with the USB boot and it works very well because it has an internal USB port, it works even better because I'm not burn an external port. I use an older version of BIOS that does not start USB ports have enough fast for the key USB is recognized from a cold start *bummer* but not a big deal. Once this is done, I'm off the coast and run very well.

    I would recommend going this way until someone comes up with a better alternative, which I would be interested in doing.

  • Satellite A665 - 12K: BT does not work - cannot find the remote service


    Help solve the problem,

    Computer laptop A665 - 12 k connected via bluetooth devices, bluetooth Manager finds the device, but do not connect it gives an error 'Cannot find the remote service' before you reinstall windiws solved similar problems 7. Did you reinstall driver broadcom, resettlement (ver.8, ver.9) bluetooth stack, clean the registry, windows 7 the relocation does not contribute to what either.. .Please help!


    I recommend you to check the services that are running in the background.
    The point is that if BT service is not running or is not enabled, the BT connection cannot be established.

    To check the service appointment on: Control Panel-> administration-> computer management tools
    or you can directly open the Services' list by typing services.msc command in RUN or Start Menu search box.

    No, you will get a list of available services. Search for services called Bluetooth and activate this service by double-click a service and select the option you want.

    Then try to reactivate the BT using the FN + F8 key combination

  • Access cannot find the macro

    Hello everyone!

    I have a damaged database. I decided to try to restore. VD, I created a new database and imported all the tables, queries, forms, reports, macros of corrupted to the new database.

    However, when I try to open most of the forms, I get the error message:

    "Microsoft Office Access cannot find the macro 'TrackDBaseForms '.

    The macro (or its macro group) does not exist, or the macro is new, but has not been saved... »

    This basis has worked for a year, and I never had this problem. A Google search returns no results. However, it is obviously not in the macros page, or in any code I can find.

    I have supports this database for a year and have never encountered this missing macro. A Google search returns no results, so I guess it's something that the developers at the beginning. However, it is obviously not in the macros page, or in any code I can find.

    The corrupted database is such a State that it will not be open to all: the main form that is set to open at startup corrupts. MS Access 2007, size 500mg.

    Thank you!

    Have u tried looking for hidden objects?
    Go to Tools/Options and view the hidden objects to open the database without starting.  You can press the SHIFT key , and then open the DB. Note You may need to do this a few times.

    I hope that this recommendation will help you. In extreme cases, you can restore the data file via the repair tool of ms access as the Access Recovery Toolbox .  

  • Mini 101NR - restore to fail, error message "cannot find the file.

    While restoring my Mini 1010NR with 8 GB SSD from the disk of XP SP3 operating system, everything fine until partially through the recovery an error message saying that it cannot find the i386\ASMS file.

    I tried the options "install fresh copy" and "repair" and get this same error message in both directions.

    I formatted the SDS with both regular and quick NTFS file system. My OSD software gives me the possibility of formatting of the SDS with fat? I have not tried. That I should?

    I looked at the CD, and in the i386 subdirectory, I see a subdirectory called ASMS. I see several subdirectories in this directory.

    I am booting from an external CD/DVD drive. This seems correct, as the installed much restoration program file until stopping in the message saying that it couldn't find the file ASMS.

    This OSD provided with the computer when I bought it new at HP.

    Thank you


    The cd is corrupted or damaged or installation loses communication with the CD-ROM drive. If you can, try another cdrom drive.

  • Cannot find the operating system files

    Cannot find the operating system files after system, Windows 7 error Ox490 HP Pavilion e9150t recovery

    Thank you very much I'll check on that.  Ended up doing a restore of the original.  Painful but successful.

  • Help to find the driver on the Satellite A200 (PSAE6) HARD disk controller

    Greetings. This text has been written through a translation program, to try to understand :)

    My friend bought a few days back to herself TOSHIBA Satellite A200 (PSAE6) where it has been established operating system Windows Vista Home. He asked me to change OS on Windows XP Pro. With the first problem I have consulted - have deleted Vista, but to set up XP is not possible due to the absence of the HARD disk controller driver in the OS distribution kit. Windows Installer cannot find the HARD drive. I read that it is necessary to load the driver during Setup, press the F6 key. But a problem I can't find the driver in that.

    We have no disk with drivers that should go with a computer and therefore it is necessary to search independently on the Internet. On the Toshiba site to locate the pilot, it was not possible. Then I came to the Intel site and download "RAID/AHCI - Intel® Matrix Storage Manager» After unpacking I got only «infinst_autol.exe» archive

    Where can I download this driver (not a "EXE" format) that can be used during the installation of Windows XP?
    PS: a chipset - Intel PM965 Express

    Thank you


    use the files in the folder "ICH8M_32bit".


  • P1102w - cannot find the printer


    I'm unable to print using a wireless connection.

    the printer is p1102w.

    operating system is MAC OS 10.10 Yosemite

    Whenever I try to print something I get "printer is not connected / cannot find the printer" message.

    I tried the solutions on your support site, but nothing helped.

    For sure, printer is connected to the same network as the computer. I see it on the print configuration page and I can connect to its IP address via a web browser (but I can't use web services).

    All software and drivers are up to date. Update Apple is nothing new to me. Niether have your site.

    I tried to move the printer closer and further away from router. No results.

    No web proxy is related to my network.

    To make this work, I have to remove the printer from my system, reinstall it using the USB cable, and then add it again via wi - fi.

    But some time the problem reappears.

    It's really frustrating. Help, please.

    Hi @xopot ,

    I see that you have problems printing via wireless network. I would like to help you today.

    Since you can access the printer embedded Web server, the printer would have a valid IP address. Most likely, it has something to do with the software that the printer uses.

    Fix permissions of the drive on the Mac:

    Close all applications.

    In the Apple menu, click OK, click Applications, and then click utilities.

    Double-click disk utility.

    Highlight your hard drive / partition on the left.

    Click on check and then repair disk permissions.

    Restart the computer...

    Reset the printing system:

    Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

    Click on the Apple icon and then click on System Preferences.

    Click on Printers & Scanners.

    Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

    Click OK to confirm the reset.

    Type the name and the correct password.

    Click OK to reset the printing system.

    Then click on the sign to add the driver, highlight the printer +. (you may need to click the drop down menu to select the name of the printer) Then click the Add button.

    Configure a static IP address for the printer.

    The printer is not found during Installation wireless.

    Do not take into account the title. Select the Solution 4: assign your printer a static IP address.

    If you need help, let me know.

    Have a great day!
    Thank you.

Maybe you are looking for