Cannot get the cell location is some devices?

Similar Questions

• Get the error code 31 this device is not working properly because Windows cannot load the drivers required for this device.

  Original title: WAN miniport driver

  A yellow sign appears on MINIPORT Wan (IP), MINIPORT (IPV6) AND WAN WAN MINIPORT (NETWORK MONITOR) for this reason I have not access to internet to throw bluetooth tethering that even he does not connect. In the properties of the driver, it indicates:-this device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I use windows 8 in my sony vaio
  MODEL - SVE15123CNW

  Hi Praveen,

  Perform the steps suggested by Nirmal S from the link below and see if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-hardware/i-get-an-error-code-31-in-Device-Manager/3364d05a-af20-4f6d-8597-b4b9f6a74b60

  Answer please if you have any questions.

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• Add/Remove components error and DVD driver error: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  Original title: Add/Remove components error and DVD driver error

  Yesterday, I removed several components of windows to attempt to clean my cpu. After the reboot, I noticed that my DVD drive disappeared. I tried to update the driver but told me I have the most updated version, I uninstalled and reinstalled the drive, but I still get the same error. Under Driver Details, it shows that I have a lot of drivers for my Phillips DVD player. However, the status of the device is the following: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) Click Troubleshoot to start the troubleshooter for this device. I've done the troubleshooting, and the two options has not fixed the problem.

  Then I tried to add windows components that I removed, thinking maybe that was the problem. However, when I try to add them, I get an error message that says: 'Setup cannot copy the file zClientm.ex_' it shows the location of this file as being in windows/i386, and of course, the file is located in this folder. So when I go to browse to locate the file, I find and click on it to open it, but I keep getting the same error message that the file is not found and Setup cannot continue.

  I realize that this problem seems very rare and weird, but any help at all would be appreciated. Thank you.

  Hello
   
   
  Code 39: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  Explanation of error codes generated by the Device Manager in Windows XP Professional http://support.Microsoft.com/kb/310123

   

   

  Method 1.
  Microsoft Automated Troubleshooting Services scans your computer and detects that the root causes of common problems, then automatically solves the problems that he finds and offers additional resources if the problem is not resolved. Click run now in the article below.

  Your CD or DVD drive cannot read or write media
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

   

   

  Method 2.
  Also, try the methods listed in the section below and check.
  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

   

   

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I replaced a HP with an Epson Stylus all-in-one printer and cannot get the printer to print more than one page when printing from the computer.

  Original title: new printer

  I replaced a HP with an Epson Stylus all-in-one printer and cannot get the printer to print more than one page when printing from the computer.  The printer works fine when printing from a laptop or ipad!

  Start by going here--> http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?UseCookie=yes&oid=232591&prodoid=63099059&infoType=Downloads&platform=nodetect

  If the web page has not correctly detected your operating system, select it by using the drop-down list.  Rather than using the "Combo package" recommended but huge, expand the "Drivers" section and download driver printer v2.32 to a location that you will remember later.

  • Click on the ORB start and go into devices and printers.
  • Select (click) the icon of your Epson printer.
  • Once you have selected the printer, a button labeled "Print server properties" will appear in the toolbar.  Click on this button.
  • Click the "Drivers" tab on the print server properties dialog box.
  • Select the Epson printer in the list of installed printer drivers, and then click 'remove '.
  • In the context menu, select "Remove driver and driver package" and click OK
  • Click Yes, and then delete
  • Once the removal process is complete, restart the computer (probably not really necessary, but can't hurt)
  • Install the driver and the software using the file that you downloaded earlier

  At this point, your printer should work fine.  However, if you want the ability to print by emailing a file to your printer, you may need to install both 'Remote Printer Driver v1.65' in the category 'Pilot' and "v1.30 utility Configuration of printer Epson Connect" in the "Utilities" category

• SD card reader problem: "Windows cannot load the driver for this hardware device because a previous instance of the device driver is still in memory. (Code 38) »

  I can't get my Dell Insperion to recognize a second SD card. It will recognize a card inserted in the integrated housing initial, but later maps not be recognized.  If I restart the computer then it will recognize a card again.  I get the following error message "Windows cannot load the driver for this hardware device because a previous instance of the device driver is still in memory. (Code 38) "your help would be appreciated.

  SD memory card

  Device type: hard drives

  Manufacturer: generic

  Location: SDA Standard compatible SD Host Controller

  Error message: Windows cannot load the driver for this hardware device because a previous instance of the device driver is still in memory. (Code 38)

  Driver provider: Microsoft

  Driver date: 2006-06-21

  Driver version: 6.1.7601.17514

  Digital signer: Microsoft Windows

  Driver details

  C:\Windows\System32\drivers\partmgr.sys

  C:\Windows\System32\DRIVERS\sffdisk.sys

  C:\Windows\System32\DRIVERS\sffp_sd.sys

  File version: 6.1.7600.16385 (win7_rtm.090713 - 1255)

  If you try to insert two cards at the same time that would be normal given that the card reader is bound to a single channel of USB. It all depends on how your computer has been configured when it was built.

  If you remove the first card and insert another card it is possible that you are not just right-click on the map in file Explorer and ejecting the card before you remove them.

• Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title - USB - IF xHCI USB Host Controller

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

  Hello

  USB devices remove all you can - restart the computer - is still there, the error? If it isn't
  It is related to one of the add-in devices that you removed. If she is still there, then, the question is
  either a device internal who can not remove or physically with the USB bus itself.
  If it was not there, add devices at a time until it is displayed - keep in mind that it is
  possible that there are two (or more) devices in conflict over the issue. Once you
  identified the check of the aircraft with the help of the manufacturer.

  1. to find the control panel - device - device - right-click on it - uninstall - Manager then
  Restart the computer to see if it clears.

  2. same place - double click on the device - driver tab - driver update - to see if that helps.

  3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
  online documentation and drivers, diagnostics and ask questions in their forums on all known
  questions. Update the Bios and chipset or other USB drivers.

  =====================================

  If necessary, we will use these additional troubleshooting methods:

  How to fix Code 31 errors
  http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

  Jake

  Hey Jake,

  Follow these methods.

  Method 1: Follow these steps:

  (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

  (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

  (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

  Remove or reconfigure newly installed unit.

  Restore a version prior to updating the driver.

  Use system restore to undo the Device Manager recent related changes.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Update the latest graphic drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• HL-dt-st dvdram gsa-t20n ata device. Windows cannot load the driver for this hardware device. Windows Vista.

  my cd/dvd drive will not read the CD and does not appear in my computer. I get the message "windows cannot load the driver for this hardware device" in the details of the properties of the device above. How can I fix it? My operating system is windows vista and I can only find windows solutions that do not work.

  Hello

  1. were there any (hardware or software) changes to the computer?

  Run the FixIt and check if the problem is solved or not.

  Your CD or DVD drive cannot read or write media (Fixit)

  Your CD or DVD drive is missing or is not recognized by Windows or any other programs (Fixit)

  Hope that helps.

• SE error message: "Windows cannot load the driver for this hardware device. The unit may be damaged or missing. "When you try to install new drivers for DVD players

  Original title: CD/DVD drives do not work after upgrade from XP to Vista

  I upgraded my dell E521 to Vista dimension, but now finds that none of the CD/DVD drives work.  I also tried two external drives, same thing.  I downloaded the new drivers for the internal disks and when I tried to install the windows said they already had the best drivers.  Both drives are TSST - I get device status "windows cannot load the driver for this hardware device. The unit may be damaged or missing. "I want to upgrade to 7, but can not run the dvd, and apparently MS has no download available if you purchase cd!  Am tearing my hair!

  Hi krt2,

  In general, the error can be caused by a missing required device driver, a required binary file is damaged, if there is a problem with the process I/O file, or if a pilot that makes reference to an entry point in another binary file which can not load

  You can try to uninstall and reinstall the driver for the device to solve this problem.

  Step 1: Uninstall the CD/DVD driver. Follow this step to do the same thing:

  a. click the Start button, select Control Panel, click System and Maintenance and then click Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  b. expand CD-ROM/DVD-Rom drives-> right click on the device, and then click Properties.

  c. on the device properties dialog box, click the driver tab, and then click on uninstall.

  d. restart your computer.

  Step 2: Reinstall the CD/DVD driver by visiting the manufacturer's Web site.

  See the links below for more details on the update of drivers:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Also, read the following article and check if that helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Computer does not recognize network. -This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello!

  I have problems connecting to my network. I stay in a House (not my own) and I can't connect to the network in this House. When I choose the option 'connect to a network', nothing happens. I followed the instructions to display the "Device Manager" and watch the 'map', and he said:

  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  When I click on this button, nothing happens... Should I simply wait for Microsoft to return to me - or is there something else I need to do?

  Thank you!

  Hello

  You must get the drivers latset for m computer support site.

  Delete the "false: entry in Device Manager and install the new drivers."

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• I can find driver for my dvd writer dose not work Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) _ dvd writer ad - 7530 has ata thanks

  Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) has .dvd rw ad - 7530 ata

  Hello

  Code 39 means that the driver is corrupted or missing.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  --------------------------------------------------------------

  Also check with your system manufacturer to see if there are any updated drivers for your DVD. Or even if it
  are you can reinstall the 'old'. Many use Windows default drivers however some special aura
  ones. Also check the website of the manufacturer of the car.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Error "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) »

  Original title: Audio recording sound recording microphone

  Hey, if I get this message:

  Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  {Unable to load device driver}
  HS device driver could not be loaded.
  Error status is 0 x %x

  When I check the status of my driver, I "updated", but he said I had the latest update installed, and when I clicked on the option for the computer solve the problem itself, after he discovered what was wrong, said, that it has not been yet fixed... I have a HP ENVY m6. Any ideas on what to do? Oh and I did a 'tune up' just a little bit before, but just the usual things nothing big or diff

  There are several models of m6 ENVY

  ENVY m6 -?

  This is a link to the audio driver for HP ENVY m6 - 1188ca (it can work also on other HP computers or not)
  This is a link to the HP support site to download drivers

  And this is something common for "tuneup", "speed up my computer", "registry cleaner" software to cause problems

  Looks like something to remove the registry entries for the driver

• Windows 2008 R2 as a guest cannot get the IP address of the server (VMware workstation 7.1.3 on Windows 7) professional

  Hi gurus,

  I installed VMware workstation 7.1.3 on my Windows 7 laptop professional x64bit and I can run my old VM (XP) without any problems in this regard. And I tried to install a new client (Windows 2008 R2 Standard x 64) on this subject, when I put the NETWORK card in the deck, he cannot get the IP address from my DHCP, always show me error "Windows has detected an IP address conflict...". ", I tried the IP static installation for her also, same result.

  I tried to install a new windows Server 2003 as a guest (also defined as a network bridge), it works very well, can get the IP address from my DHCP or can set a static IP address with no problems. Does anyone have a similar experience on this combination? Any solution to this issue?

  Best regards

  BUGBUG

  I recently managed to get bridge network work with a Windows Server 2003 R2 SP2 guest in VMW Workstation 7.1.4.385536 on a host Windows 7 SP1 Ultimate.

  VirtualBox 4.0.4.70112 is installed on the host and disabling the 'VMware Bridge Protocol' in the 'VirtualBox in Ethernet Adapter"on the host was necessary.

  Outpost Firewall Pro 7.1.0.3415.520.1247 is also installed on the host computer and I used some information from the link below to add some necessary firewall rules.

  http://www.agnitum.com/support/KB/article.php?id=1000061

• Cannot get the password or re-establish the link. What should I do?

  Cannot get the password or re-establish the link. What should I do? Reset email is never sent. This master password"... How do you define? I'm locked out of Thunderbird. Help

  Maybe he's trying reset Pasword Thunderbird Master as I'm doing? I copy the code and paset in the console tools\error and press Evaluate. I wonder if I want to reset the Master PW and I say yes, then I get a saying that the Master PW has been reset. Maybe he's looking for an e-mail to tell him that the IPL has been rest to? But the problem is, nothing happens when the password has been reset, msg is sent. TB continues to request the password. I have not changed my PW and when I enter the good PW, TB does not recognize. And reset the PW Master does nothing but generate Pop up messages. It's very frustrating. The information in the help files are not accurate, or the code provided does not work although it generates messages indicating that the IPL has been reset.