cannot print wireless to wireless using a but access point wired printing (pc) wireless technology is very well

Similar Questions

• AC1900-Nighthawk WiFi Range Extender can be wired in and used as an access point?

  I want to replace my WN802T which is connected to the network.

  Found the manual and it can be used as an access point.

• Photosmart wireless 6510 works very well, but how now to enable web services & eprint?

  New wireless photosmart 6510 works well with my laptop (Windows 7) to home & router; How can I activate the web & eprint services NOW? During the initial installation, I was short of time and I think that the antivirus intervened and I don't have a printer email address. He said that I could do it later - how? When I use the Web Services Panel to printer it tells me that I am not connected to the server.

  Is there a pure easy way to add web services now without upsetting my wireless network settings?

  bjhulse22,

  The steps below a usually resolve the problem you are experiencing:

  1. unplug the power cord at the back of the printer.

  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).

  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.

  4. wait for 30 seconds, then plug the printer back and power.

  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.

  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):

  1. print a Configuration Page from network network printer or wireless menu.

  (Select the wireless icon, select 'Settings', select "Display Network Configuration", select "Print Info")

  2. open a Web browser and type the IP address of product (from the network Page of Configuration) in the address line. The HP - Embedded (EWS) Web server should open.

  3. click on the tab 'Network' (in the top menu), then click on the 'Networking' link (in the left menu), then click on the link "network address (IP).

  4. click on the small round button next to the "Manual of intellectual property", then fill in the fields with the information from the Page of Network Configuration (IP address, subnet mask and default gateway).

  5. under "Setting up the DNS addresses", fill in the fields with the following text:

  -Preferred DNS: 8.8.8.8

  -Alternate DNS: 8.8.4.4

  6. click on the "Apply" button and the settings must be updated. Once the settings are updated, turn the printer off and then back on.

  7. try to reactivate Web Services.

  Let me know if you have any other questions, please!

• iMac cannot connect to 7520 printer (wired) - after six months of work very well.

  My Photosmart 7520 worked fine for six months - cables for iMac, wireless for Mac Book and iPad.

  Suddenly, the iMac to which it is connected, unable to connect to it.  Then, of course, the other devices in the House cannot connect wirelessly is.

  1. total stop did not help.  Printers, sometimes he showed a light yellow, sometimes shown green and slowed down... but sending print jobs made back to "unable to connect".

  2 remove the printer from the list, and since the iMac can't find it, I now have nothing.

  3. I can't do a reset of the printer because I lost the driver for my old Perfection 2400 scanner.

  I have never been able to activate the web services.  That this has something to do with it?

  Help. Sandy

  Hi Sandy,

  Sorry to hear that there are some problems with your connection to the printer Photosmart HP 7520.  If you don't mind not could you please answer a few questions that might help me understand what could happen.

  The 7520 Photosmart printer has an Ethernet (wired network) port, in "wired", I'll assume you mean that the printer is connected to your iMac via USB cable.  You the first thing I would try is to unplug the USB cable to the back of the printer and taking again and then do the same thing at the back of the iMac.  I know that sometimes because of the angle of the cables, they can be loosened.  See if the iMac can then "see" the printer.

  You can remove the printer from the printers and Scanners, system preferences, selecting the printer in the list on the left, then pressing the key less at the bottom of the list.  This should in no way affect or not wearing your Epson Perfection 2400 is always configured in your PC.

  Can you please tell me if your iMac is on the (access point) network as your MacBook and iPAD?

  When you use your iPAD to print, it can "see" the printer (you can select or it appears by name)?

  Finally, if you tap the wireless on the front panel of the printer, it should display the IP address of the printer.  Your MacBook when it is connected to your wireless network, open Safari and type http:// and the address of the printer showed you.  Safari open the page Web of the printer or a mistake?

  Thank you

  VancDarkstar

  I am an employee of Hewlett-Packard

• Cannot connect to my Satellite A210 adapter for access point

  Hey everybody...

  I have a little problem with my wireless. We have some books and access point. Everyone can connect to access point except me. I have the Satellite A210-127. Do you know where is the problem? How can I connect to the access point?

  Thank you

  In a first time, you must activate WLAN antenna correctly. Upon first use WLAN switch and set it TO position (the LED will be ON). Next step is to use the FN + F8 key combination. Don't forget THAT WLAN is enabled.

  After this use please ConfigFree radar to see if the access point is visible for your laptop.

• Sites Web open do not, but other applications internet like Skype, viber, messengers works very well

  Hi guys,.

  It comes to Nilesh, I really need help in this case.

  Since last week, its been observed on my Dell Inspiron 3521 to i5 with HDD 750, 4 GB of RAM (Service Tag # ), that in spite of the use of 10 Mbps ethernet speed cable, the site does not open unless I restart the computer each time but other applications such as Skype video calling, viber works very well, the torrent files are also downloaded great at high speed.

  What I've done so far-

  (1) the connection on the router - OK

  (2) RJ45 Ethernet connector was broken - fixed.

  (3) Firewall setting - ON (default)

  (4) I've restored the system as well.

  (5) Avast Anti-virus manually installed on my PC and its ON 24 / 7 and I also scanned my computer and not threats that will find there also.

  (6) my system is up to date, I have downloaded a few applications for the Dell software update on my 3521. So, it updates the new versions automatically and automatically restarts the computer.

  (7) I have tried to connect my laptop directly with the cable coming from the wall too, still the same problem.

  Despite all this, the only problem Im making ' is difficult, impossible to open the Web site. I can open the Web site but only when I restart my laptop and that too for only 10 or 15 or 20 or 30 minutes. After that, one more time of site question. I mean, the Web sites stop opening after 20-30 minutes.

  Some of my friends, colleagues suggest me to get the laptop formatted.

  So, my request here is, do I really format my C drive? If there no need other alternatives, please please please share. (but, before that, please read everything that I did on my 3521 far to avoid a repetition)

  If other than all of the above, and if I need to format my C drive, let me know the procedure of formatting PC which I think will be clean the PC and start from scratch. So far I got the backup of my C drive to the D drive.

  I would appreciate your help in this matter, as its so frustrating. I hope you understand my situation here.

  Thank you very much!

  Nilesh

  Hey you!

  You simply Rock buddy...

  What a most satisfying to your precise support of bar.

  I followed the steps you told me, and I was able to download successfully from chrome and mozilla firefox, as well as the software application anti malware free one that told you me... and did a quick scan by your suggestion. And, guess what, there were approximately 136 flaws that I deleted the system. (BDW, digital defects had a few registeies also, but not sure if I did it correct that I removed, could you explain me basically what it is, is it a virus or what and how is it that night my computer?) Just for my tech knowledge.)

  Now, my system works like a butter on a roll. You just need a raise!

  G $ thanks to you, Ricki.

  Nilesh

• cannot open FishWorld app Facebook using FF, but FW opens in Internet Explorer.

  Installed Fire Fox. It cannot open app Fish World on Facebook. FW opens in Internet Explorer.

  This has happened

  Each time Firefox opened

  Your known list of plugins obsolete tampon() watch with security and stability risk.

  # Java Plug-in 1.6.0 for Netscape Navigator (DLL Helper)
  

  Update the Java plugin to the latest version.
  See http://java.sun.com/javase/downloads/index.jsp#jdk (you must have JRE)
  ---
  IE uses an ActiveX control to manipulate Flash objects.
  Firefox uses a different NPAPI plugin.

  Your list of installed plugins posted above does not show the Flash for Firefox plugin.
  See Flash Plugin - maintain and troubleshoot and install the Flash plugin to display videos, animations and games

  You can get the Flash Player here: http://get.adobe.com/flashplayer/otherversions/ (Adobe Flash Player)
  'Please select the operating system' and make sure that you get the ' browser: Firefox, Safari, Opera "version.
  Make sure that you remove any tick this option to install other software (free McAfee Security Scan (optional))

• Desktop (Wired) not pulling IP; my works (wireless) cell phone very well

  I lost my internet connection; att tec guys are out could fix it .my laptop works fine .the office (cable) keep referring to my ip address problems

  Hello

  1. What is the brand and model of the computer?

  2. what security software is installed on the computer?

  3. have you made changes on the computer recently?

  4. What is the accurate and complete error message you get?

  5. have you update service pack 3 installed?

  6. What were the measures deemed by the ATT technician?

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not persist in SafeMode with network, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: Follow the steps in the article.

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

  Refer.

  Wired and wireless in Windows network connection problems: http://windows.microsoft.com/en-US/windows/help/wired-and-wireless-network-connection-problems-in-windows

  I hope this helps.

• Belkin router and wireless card worked very well and then one night they stopped working randomly.

  It's a belkin router and belkin wireless card. It was working fine one night and the next day he does not see the router. I have reset the router and the wireless card. Reset the computer and cell phone, but still no access. The lights are on the wireless card and I got no error messages.

  original title: laptop does not see my network router.

  Hello

  · Who is the service pack installed on the computer?

  You can try the steps he listed in the links: how to fix wireless network connections in Windows XP Service Pack 2: http://support.microsoft.com/kb/870702

  Problems in Windows wireless and wired network connection: http://windows.microsoft.com/en-US/windows/help/wired-and-wireless-network-connection-problems-in-windows

  You can also run the troubleshooter by downloading the file from the link: focused on troubleshooting Microsoft Windows XP with wireless networks in small businesses or individuals: http://www.microsoft.com/downloads/en/details.aspx?FamilyID=35c7e5ad-59e7-477b-9d27-6a7030e67002&displaylang=en

• just installed cloud print on my mobile. works very well with my 5510 but only print black and white.

  Anyone know why I can only print in black and white on my photosmart 5510 when you use cloudprint of

  My HTC desire hd. ?

  Hi brianmadmidge,

  Here's what you need to do to change the settings for printing for Google Cloud Print:

  1. Go to https://www.google.com/cloudprint/learn/ and click on "Try it now" (you may be prompted to sign in if so, sign, then click the link again.)
  2. A pop-up will appear with your list of printers.
  3. Select a printer.
  4. Click on options.  Grey_K will be black ink only, Grey_CMY will be high quality gray and color will be full color.

• When I hit a link to a page in my directory in code view and I click on the link using live view, it does not to this page.  But if I saw in a browser, it works very well.

  When I hit a link to a page in my directory in code view and I click on the link in live mode view, it does nothing.  When I then go to preview in a browser, it works fine.  Can anyone help?

  To follow links in Live View mode, hold down the CTRL on Windows or the command key on a Mac key, and then click the link. Clicking on without using the Ctrl/Cmd key simply selects the link in Live View mode.

• Restored PC to factory settings now will not opt for 'view wireless Netwoks. Very well with cable and 2nd PC sees the network OK

  XP SP3, MX693b of the entry door.

  Please list the steps you took to do the restore.

  What is the brand and model of the computer?

  Did you restore by going to Windows Update?

  What version of Windows is now on the computer, including service pack (right click on my computer > properties)?

  Did you uninstall all versions of software antivirus which have been restored when you restore the factory State "free trial"?

  You have installed an antivirus application?  Which one?  What's his current subscription?

  Open the Device Manager (start > run > devmgmt.msc > OK), then click on the + sign next to "network adapters."  What devices are listed?  None of them showing warning icons?

• When I try to printe a photo of my photo library, it says printer does not print, not connected etc. Yet if I ask it to print a document it does very well. What is the problem?

  I have a number of photos in my photo library. The printer is a Dell V510 series and was bought in June last with a new computer. He tells me to plug in the USB, it is and several other things that are all connected. In my library of images are printed documents. When I ask to print to it. Also when I received a photo by e-mail or download from my camera I never know where he's going to put the picture. I've never had a problem with my Windows XP but Windows 7 doesn't seem to do what I want it. The instructions that came with it are almost useless. I am not a technician, but I am new to the computer. Thank you

  None of the problems you mentioned sound like they are related to Firefox.

  You are able to print web pages through Firefox?
  
  This "image library" display images in Firefox, or is it a separate program? y at - it assistance > on the menu in this program item? If Yes, what does say?

• Importing video, audio is fine at the beginning but the audio desync later vid.  Audio is very well during playback with VLC/Quicktime

  Use of elements 13 trial on mac first.  An imported video - audio synchronized to the top at first but later in the video, the audio is far away.  There are some quiet parts so I can't say exactly when the audio desync.  Played in VLC/Quicktime, audio is perfect all the way through, there seems to be a bug in first.

  Any advice?

  Searched the forum for other solutions since handbreak is always hours of late.

  "Interpret video" with fixed framerate seemed to handle the audio track somehow, but it's still desynced.

  BUT

  Oddly, replacing the extension of the source file to .mpg .mp4 seems to remedy.  Would be nice if the first can handle this automatically, but it's a pretty easy fix.

• RTMP server connected, but not video in the player. HTTP works very well

  Hello

  
  

  Here, a problem, I put http server which is connect and video game,.

  But server rtmp connected but the video does not.

  Trace of information :

  trace (event.info.code) = NetStream.Play.Reset, NetStream.Play.Start (output in flash)

  http Host

  ------------------

  var videoURL:String = "http://www.helpexamples.com/flash/video/cuepoints.flv";
  var connection:NetConnection;
  var stream:NetStream;
  var video:Video = new Video();
  NetConnectionExample();
  function NetConnectionExample()
  {
   connection = new NetConnection();
   connection.addEventListener(NetStatusEvent.NET_STATUS, netStatusHandler);
   connection.addEventListener(SecurityErrorEvent.SECURITY_ERROR, securityErrorHandler);
   connection.connect("null");
  }
   
  function netStatusHandler(event:NetStatusEvent):void
  {
   switch (event.info.code)
   {
   case "NetConnection.Connect.Success" :
   connectStream();
   break;
   case "NetStream.Play.StreamNotFound" :
   trace("Stream not found: " + videoURL);
   break;
   }
  }
   
  function securityErrorHandler(event:SecurityErrorEvent):void
  {
   trace("securityErrorHandler: " + event);
  }
   
  function connectStream():void
  {
   var stream:NetStream = new NetStream(connection);
   stream.addEventListener(NetStatusEvent.NET_STATUS, netStatusHandler1);
   theVideo.attachNetStream(stream);
   stream.play(videoURL);
   addChild(theVideo);
  }
   
  function netStatusHandler1(event:NetStatusEvent)
  {
   trace(event.info.code);
  }
   
  function onMetaData(info:Object):void {
          trace("metadata: duration=" + info.duration + " width=" + info.width + " height=" + info.height + " framerate=" + info.framerate);
      }
      function onCuePoint(info:Object):void {
          trace("cuepoint: time=" + info.time + " name=" + info.name + " type=" + info.type);
      }
   
   
  

  Host RTMP

  ------------------

  var videoURL:String = "filename.flv";
  var connection:NetConnection;
  var stream:NetStream;
  var video:Video = new Video();
  NetConnectionExample();
  function NetConnectionExample()
  {
       connection = new NetConnection();
       connection.addEventListener(NetStatusEvent.NET_STATUS, netStatusHandler);
       connection.addEventListener(SecurityErrorEvent.SECURITY_ERROR, securityErrorHandler);
       connection.connect("rtmp://servername.host.com/foldername");
  }
   
  function netStatusHandler(event:NetStatusEvent):void
  {
       switch (event.info.code)
       {
            case "NetConnection.Connect.Success" :
                 connectStream();
                 break;
            case "NetStream.Play.StreamNotFound" :
                 trace("Stream not found: " + videoURL);
                 break;
       }
  }
   
  function securityErrorHandler(event:SecurityErrorEvent):void
  {
       trace("securityErrorHandler: " + event);
  }
   
  function connectStream():void
  {
       var stream:NetStream = new NetStream(connection);
       stream.addEventListener(NetStatusEvent.NET_STATUS, netStatusHandler1);
       theVideo.attachNetStream(stream);
       stream.play(videoURL);
       addChild(theVideo);
  }
   
  function netStatusHandler1(event:NetStatusEvent)
  {
       trace(event.info.code);
  }
   
  function onMetaData(info:Object):void {
          trace("metadata: duration=" + info.duration + " width=" + info.width + " height=" + info.height + " framerate=" + info.framerate);
      }
      function onCuePoint(info:Object):void {
          trace("cuepoint: time=" + info.time + " name=" + info.name + " type=" + info.type);
      }
   
   
   
   

  I think that with rtmp you want to delete the file suffix... so try:

  var videoURL:String = "filename";