cannot read the source file or disc for install.wim when file copying.

Similar Questions

• Error copying file or folder: cannot read the source file or disk.

  My problem occurs when you try to copy on the same computer I am on (or to a remote drive).  I get one of these messages in the dialog "error copying file or folder.

  box:

  Impossible to copy 'Filename': data error (cyclic redundancy check).
  Impossible to copy 'Filename': cannot read the source file or disk.

  Hey Norton victim,
  
  (a) what is your operating system?
  (b) what program file you are not able to copy?
  
  As the files are copied, Windows verifies that the data that has been copied are the same as the source files. The cyclic redundancy check (CRC) error occurs when the copied data does not match the original.
   
  This could be down to a mistake of the DVD, the disc goes wrong and has failed to 'read' the file properly or the file was placed on a bad sector on your hard drive. (Could be just down to a scratch or some marks on the dvd, maybe clean it if necessary and try again).
   
  I would run a check disk (CHKDSK) against the drive to rule that, although lacking - you have another dvd player to try the disc again? If so, try the dvd in another drive, or even a completely different machine to try to pin-point the problem.
   
  At the command prompt, type the following command and press ENTER:
   
  Chkdsk /r
   
  Note: If bad sectors are detected when running check disk utility and attempt recovery of bad sectors is verified during the verification of the drive for errors, data in the bad sector can be lost as they tried to recover bad sectors.
  
  FOR INFO:
   
  Data error (cyclic redundancy check)"Error Message When Outlook downloads E-mail
  http://support.Microsoft.com/kb/319128
   
  Aziz Nadeem - Microsoft Support

• Cannot delete files from 0 KB Word 2003 "cannot read the source file or disk.

  Original title: how remove the files from Word 2003 0 Kb which can not be read - file cleaner empty and an empty folder solvent do not work - "cannot read the source file or disc!

  I have a number of Word 2003 files that I'm unable to delete, since the message "Source file can not be read"appears when I try to delete.
  I have tried vacuum cleaner and Remover empty folder, also delete - file but cannot delete what cannot be recognized. Can anyone help please? Must be an easy way to do what I forgot, because I can't send files that contain some of these bulk files in my backup hard drive, the process stops when it reaches the 0 kb file!

  Hello

  1. where are the files located?
  2. are you able to open this file?

  This can happen if the file is used by some programs / demand or is corrupt.

  Follow these steps:

  Method 1: Check if you are able to delete the files in safe mode.
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

  Method 2: Ownership of files and check if you are able to delete.
   http://support.Microsoft.com/kb/308421

• Cannot delete file: cannot read the source file or disk

  When you try to delete a specific folder which shows on the list, I get a dialog box saying: error deleting file or folder... Cannot delete file: cannot read the source file or disk

  Is the path to the really long folder?

  Any file or folder has a space beginning or end?

  Click Start, run, type cmd , and press ENTER to open a command prompt. In the command prompt...

  For a file test

  DEL \\.\driveletter:\path\filename

  For a test folder

  RD \\.\:\\
   
  If this doesn't help not please let us know the full path (and the name of the file if it is a file).

  Tricky

• "Cannot read the source file or disk" when copying photos

  I am train back to top/save families photographs stored on the C drive in the folder 'My photos' on an external HARD drive.
  Whenever I am trying to copy and to, I get a message saying "cannot read the source file or disk.  If I keep on pressing the button 'Try Again', he eventually some of the files copy the external HARD drive and fails on some.  There are times when I hit the "try again" Button to 30 times before it complies.
  I am logged on as administrator and am running Windows 7 on a HP laptop.  Could you help me debunk this?  I am beyond frustrated with this since I want to save precious family memories, but I am upset about windows on each attempt.
  Thank you
  Sandrine

  Hi JasjitRehsia,

  I've seen some posts where it is perhaps due to an error on the hard disk. See the article after some troubleshooting:

  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

  I hope this helps!

• Windows 7 can't copy files on external hard drive and keep showing "cannot read the source file or disk.

  Windows 7 can't copy files on external hard drive and keep showing "cannot read the source file or disk" HELP me PLS
  I'm going crazy because of this

  Hello

  1. What is the format of the file system on the external hard drive?

  2. are you able to copy or move files into the computer?

  You can follow the suggestions mentioned below and check with the question.

   
   
  Method 1:Delete CCG, prefetch files.
   
  Step 1: Delete Temp files

  (1) open the window run (Windows key + R)

  (2) type %temp%, and then press ENTER

  (3) delete all Temp files in the Temp folder
   
  Step 2: Delete Prefetch files

  (1) open the window run (Windows key + R)

  (2) type %temp%, and then press ENTER

  (3) delete all files in the Prefetch folder.

  Method 2: Run the tool (SFC.exe) System File Checker, try to copy the files and check.
   
  Follow the form of measures the following link: http://support.microsoft.com/kb/929833
  Method 3: Run the check disk then try to copy the files and check.
  
  Check a drive for errors
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
  Note: If bad sectors are found in the hard drive then it could try to fix this particular sector. If you have any data on that, it can get lost.
   
  See also: http://support.microsoft.com/kb/976972
   
  I hope this helps!

• Impossible to remove a file from the desktop, get the error message "cannot read the source file or disk.

  I can't delete a file from my counter top. Error message: cannot read the source file or disk. He is an Adobe file with logo in white box.

  Boot into safe mode and see if it will remove. If this is not the case, try this tool.

  Unlocker File Remover

  Download it from FileHippo
  http://filehippo.com/download_unlocker/

  Download from CNET
  http://download.CNET.com/WOT/3000-2378_4-75011499.html

• How can I delete a file? Whenever I try this a file, it keeps saying "cannot delete file: cannot read the source file or disc» Any ideas anyone?

  I have some files that have been sent to me by a colleague. I have removed but cannot delete the last file. I've never met this before. What should I do?

  Thank you

  Sunil

  Try this:

  http://www.ehow.com/how_8023561_cannot-delete-files-Windows-XP.html

  It will be useful.

• current noise to the top of the "error copying file or folder" cannot copy file: cannot read the source file or disk.

  is popping up even though I do not copy even nothing at all. If I close the windows, it keeps popping up all the time. There is also no mentioned file...

  OS is XP

  Hello

  You can view these methods:

  Method 1:

  You need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  Method 2:

  I suggest you make a system full scan just to be sure.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• I'm trying to delete a file and I get the message cannot delete file: cannot read the source file or disc HOW DO I GET RID OF THE FILE?

  There is an icon on my desktop I want to remove

  Tskilonger,

  Welcome to the Microsoft Answers community.

  Try to delete the file in safe mode:

  To use a boot option, follow these steps:

  1. reboot your computer and start pressing F8 on your keyboard. On a computer that is configured to start to multiple operating systems, you can press the F8 key when the Boot Menu appears.

  2. Select an option when the Windows Advanced Options menu appears, and press ENTER.

  3 when the boot menu appears again, and the words "Safe Mode" appear in blue at the bottom, select the installation that you want to start, and then press ENTER.

  I hope this helps.

  Lisa
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I can't delete a file. Error code "" cannot delete file: cannot read the source file or disk "?"

  I saved two accessories to my email which could not be read. I've identified Micrsoft Word like the program to use so he opened one of them OK and I was able to remove it. However, I can't delete it. Properties of one, I can not delete are of file Type:, file size: 0 bytes; size on disk: 0 bytes.

  Today was the second time this has happened to me.

  Try to start safe mode and see if it will remove. If this isn't the case, give this tool a whirl.

  Unlocker File Remover

  Download it from FileHippo
  http://filehippo.com/download_unlocker/

  Download from CNET
  http://download.CNET.com/WOT/3000-2378_4-75011499.html

  You may need it as well.

  How to capture a file or a folder in Windows XP
  http://support.Microsoft.com/kb/308421

• Cannot copy file: cannot read the source code or drive WINDOWS XP

  I'm trying to transfer pictures on my old XP computer on an external hard drive.  After performing a backup on the drive hard seagate WD I went looking for pictures on the external hard drive, and they aren't there.  I went back on the XP machine and tried to copy the files to a CD but I get the message cannot copy file: cannot read the source code or the player.  I can open images but cannot move it to another folder or copy and paste pictures anywhere.  The photos are saved in an outdated version of microsoft's digital imaging software.  Help, please.

  Hello

  (1) is the specific question of the images?

  (2) where the images are on the computer?

  You can try the following methods and check the status of the issue.

  Method 1:

  Configure the computer to clean start State to check software conflicts. See the following link on how to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 4 of the above article.

  Method 2:

  If the problem is specific to the pictures folder, then it might be a problem with permission. You can try to take ownership of the folder and check if you can transfer it. read the following article.

  How to capture a file or a folder in Windows XP?

  http://support.Microsoft.com/kb/308421

• Toshiba Recovery For Vista: 10-FC06-0002 "cannot read from source file or disk" Preinst.8

  I recently lost a hard drive and I had a new installed in a laptop Toshiba Satellite A305-S6905.  I ordered the recovery media and when I run it it starts copying files and then publishes the message "Cannot read from source file or disk" and says it's PREINST.8.  I don't know what that means.  The hard drive is new, the recovery media is new, and I don't know how to go further.  It gives me the ability to ignore and I anpother error message which says 10-FC06-0002, and that the recovery does not and click on 'ok' to restart the computer.  I'm at an impasse in circles.

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  You will need to contact Toshiba re problems with their recovery media.

  This isn't their recovery process, Microsoft.

  See you soon.

  Mick Murphy - Microsoft partner

• Computer cannot read the .vp3 files needed for my embroidery software

  Title: original .vp3

  I try to install the embroidery software that came with my new sewing machine and although pilots seem to have installed ok I can't access embroidery designs, because the computer says that it cannot read the .vp3 files.  Why he cannot read, and how do I read that I can use on the machine.  Someone told all the answers no computer talk please.

  Unfriendly computers Hello,

  I'm not very familiar with the .vp3 extension but do not know that it is an extension that Pfaff is normally used. Look at the link below, because it gives the means of obtaining the .vp3 on a Windows machine.
  http://www.PFAFF.com/ca/en/media/CA/PF_INSTRUCTIONS.PDF

  Your program is not compatible with Windows 7. Check and see if you can use compatibility mode.
  Compatibility mode is incorporated on your computer, when you right-click on any application or program and select it properties, you have a Compatibility tab.
  In compatibility mode, we have options to manually change the settings.

  If you have problems with a program that worked correctly on an earlier version of Windows, select the compatibility mode that corresponds to this version.
  Run this program in compatibility mode for:
  Select the Compatibility tab: you can choose to run the program in Windows XP compatibility mode, or even all the way back to Windows 95 compatibility

  See the below link for more information about the same:make sure to run older programs in this version of Windows: http://windows.microsoft.com/en-US/windows7/Make-older-programs-run-in-this-version-of-Windows

  Please let us know if this helps solve your problem.

  Sincerely,

  .

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• 12.1.1 new install: AC-00402: cannot read the driver file: addbtmpl.drv

  Hello
  
  Im making a new 12.1.1 install the new test server and unziped downloaded media on the disc (not not using DVD). I ran not adautostg.pl because I felt is was not necessary because the downloaded media.
  
  I did the pre-installation steps according to metalink 761566.1
  He did uncompress drives then I get the following error and I can't file: addbtmpl.drv anywhere. This is step 2 of 5-> database configuration 92% (RW50004). I can't proceed immediately.
  
  /U01/app/Oracle/DB/tech_st/11.1.0/appsutil/log/VIS_ < servername > 09171403.log
  
  Logfile located at /u01/app/oracle/db/tech_st/11.1.0/appsutil/log/VIS__ < servername > ApplyDatabase_09180926.log
  
  
  | 0% completed AC-00402: cannot read the driver file: /u01/app/oracle/db/tech_st/11.1.0/appsutil/template/addbtmpl.drv
  
  Cannot run configuration database using RapidClone
  
  RW-50010: error:-script returned an error: 1
  RW-50004: Error Code when you run the external process. Check the log file for more details.
  Install the driver of database running for instance SCREWS
  
  Thank you

  Im making a new 12.1.1 install the new test server and unziped downloaded media on the disc (not not using DVD). I ran not adautostg.pl because I felt is was not necessary because the downloaded media.

  You don't need to run the intermediate script if you have downloaded the site Web e-Delivery - in the electronic help files fast delivery to install in Oracle E-Business Suite Release 12 [406138.1 ID]

  I did the pre-installation steps according to metalink 761566.1
  He did uncompress drives then I get the following error and I can't file: addbtmpl.drv anywhere. It is step 2 of 5--> (RW50004) database configuration 92%. I can't proceed immediately.

  0% completed AC-00402: cannot read the driver file: /u01/app/oracle/db/tech_st/11.1.0/appsutil/template/addbtmpl.drv

  It seems that the file is missing.

  Please run md5sum according to (checksums MD5 for R12.1.1 Quick Install Media [802195.1 ID]) to check the integrity of the domain stage directory before running the quick installation.

  Thank you
  Hussein