Cannot start Windows, Windows Setup does not detect the hard disk, Bootmgr is misiing
I have a few problems on my laptop [Acer 3810 t]
-The first problem
My mobile give me screen "cannot start windows' who have 2 choices: run the Startup Repair tool and boot normally. I chose to fix it, but nothing happens and stuck "starting windows" and gives unmountable boot volume 'blue screen '. the Dungeon of blues screen appear (for laptop is a not restart). So I turned off my phone and turn it back on it. the "could not start" screen again and I chose to start normally. but the result is negative. My portable Dungeon cannot start windows. Because of that I am using the advanced boot option and choose all the boot type such asit cannot load the safemode, last configuration etc, but the result is the same, you cannot start windows. in safe mode, its stuck in loading fileinfo.sys. I do not give up to try again with the advanced boot option. until I have a bad situation. My laptop can only 1 file in safe mode and blues screen do not appear again (my laptop only return at the beginning of start or restart)
-The second problem
because it cant solved, I want to reinstall my laptop. My OS is Vista 32 bit (pre-installed). I want to install the new operating system, windows 7. I use Dsik Flash bootable USB to install Windows 7. But in the BIOS, it is detected as a USB HDD. So I set my BIOS to load USB HDD to the first order. the installation can be done, but only until the "start Setup" screen and its deadlock. I have it wait up to an hour, but nothing happens. So I'm going to BIOS, change SATA mode to IDE mode AHCI. Then load the USB and go "installation program start screen. but the new problem is the installation of window does not detect my hard drive. So I can not choose the place to install the operating system. I have to load the driver, but I did not. Again to load the configuration to AHCI and IDE, until I get my HDD can detected in IDE mode. So I think I can move easily, I choose custom installation and choose the hard drive to install the operating system. But unfortunately, at the beginning of the process, after choosing the OS, the Installer gives error if installation location the installation failed. (I forgot the error message)
-The third problem
So far, I can't spend 'startup begins' as well in mode IDE and AHCI. Also bootmgr in my hard disk is missing, so I can't go to move the startup repair or the startup option in my HDD as before
What is the error code that you got with blue screen?
I think that there is a problem with your drive HARD check that by contacting acer...
Tags: Windows
Similar Questions
-
Airport utility in windows 10 does not detect the hard disk, how to?, the Office detect wireless internet no hard drive.
What hard drive? It of a time capsule, or is it a drive connected to an airport extreme?
What model number is the most convenient airport?
Any plugged into USB drive must be formatted FAT32 (no other type of FAT as exFAT) or HFS +, IE standard Apple format.
In addition, not all drives are recognized.
The internal drive of the TC must be recognized, but there could be problems as well according to the age.
-
Windows 7 does not detect the additional disks in the selection of drive during the instalation
OK, I have a Dell Inspiron 17r 7720, it has 2 drives 750 GB and a 32 GB ssd
the installation of 7 single 750 GB is available, the other 2 drives are no where to be seen
all are detected in the bios
any information would be greatly appreciated
Thank you
Hello
Please keep us updated on the status of the issue.
However, tried to run the Hardware Diagnostic Utility for the hard drive such as suggested by Ashish Sondhi responded on 22 November 2014.
If so, please answer with the results, in order to help you solve the problem.
Thank you
-
Windows 8 does not see the hard drive on the Satellite A200
Windows 8 does not see the hard drive on the A200.
How to install it?S strange Windows 8 should already contain the HARD drive controller driver to recognize the HARD drive during installation.
The HARD drive is visible in the BIOS?Do you use the original disc from Microsoft of Windows 8?
-
Installation of Oracle 11 g R2 grid does not detect the ASM disks
Hi guys,.
I'm trying to install Oracle 11 g R2 RAC and as part of the installation of the grid, the Setup program does not detect the ASM disks.
Here are the outputs for some commands.
[root@rac1 ~] # oracleasm scandisks
Reload from disk partitions: fact
Cleaning up stale ASM disks...
ASM disks scanning system...
Instantiation of disk 'ASMDATA2 '.
Instantiation of disk 'ASMDATA1 '.
[root@rac1 ~] # oracleasm listdisks
ASMDATA1
ASMDATA2
[root@rac1 ~] # ls - ls/dev/oracleasm/disks
Total 0
0 brw - rw - 1 grid asmadmin 252, 3 14 May 17:18 ASMDATA1
0 brw - rw - 1 grid asmadmin 252, 2 14 May 17:18 ASMDATA2
I already tried to reconfigure Oracleasm (oracleasm configure - i) but no luck.
I would be really grateful for the help here as its been a few days now and want to complete the installation as soon as possible
Concerning
Praveen
Thank you Ricardo, I see now the disks after you change the path from discovery to/dev/oracleasm/disks
-
Windows xp64 does not detect the printer hp laserjet p1102
Hello
Windows XP Professional X 64 Edition Version 2003 is installed on my server. It does not detect the printer HP Laser Jet P1102, it needs of Virtual Port USB 001. When I connect my printer, Windows does not detect the printer. I lost the CD for the printer. When I try to install the printer with drivers downloaded HP, it gets sleep showing message "Connect your USB cable" when it is already connected.
Also when I try to connect to the printer on my workstation, Windows XP Professional 32-bit Edition, it must be connected, but off, the sharing is lost with other workstations, even if I set the static IP for all.
Hello
I suggest you post your query in the TechNet forum. Please post your question in the link for assistance below: http://social.technet.microsoft.com/Forums/en-US/itproxpsp/threads
-
Qosmio F30 - 112 - Windows XP does not recognize the HARD drive
Hello.
I have a Qosmio F30-112.
I tried to install the Windows XP Professional instead of the Media Center edition.
However, during the execution of the installer, my laptop does not recognize the hard drive. Therefore, the installation cannot continue.I thought it might be a problem of corruption with my laptop and reinstalled Media Center Edition successfully.
But when I try to install XP Professional it always gives me the same error.Suggestions for the configuration of the BIOS or solutions for why this is happening?
Thanks in advance.
Hello
Just a question:
You are looking for in this forum for other similar issues with regard to the installation of Win XP and lack HARD drive? I doubtThe fact is that your notebook has a SATA controller and you need a SATA (Intel Matrix Storage Manager) driver.
You should have a look here in this doc from Toshiba:
[How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]and should also search this forum for other threads
Good bye
-
I bought a new pc to replace my old hp 14 months as the motherboard fried in. I bought a case of disk external hard to rocketfish to put the hard drive of my Windows 7 pc in. burned does not see the hard drive. my old pc with xp can access all the items on the external hard drive.
Check that the drive appears in Device Manager.
If so, go to disk management and assign a drive letter.
-
Recovering the Windows system does not recognize the hard drive
Computer does not recognize the hard drive when booting. Guard gives me 1782 disk error. Then try to use the ROM installation thing and throw a disc hard test there is no option to test anywhere. Computer was working fine this morning and then I stop when I turned it back on it was not properly start.
I have a zt3000 running xp sp3
someone please help me, thanks
Hello
Please reinsert the drive from the rear panel and check if the device detects the drive hard in case you have the same problem, then the hard drive is bad, you need to replace the hard drive and reinstall the operating system on the unit to return to its operating state.
-
Help me. H700 RAID does not detect the HARD drive.
Hello everyone!
My Dell C2100 used CPU X 5650 and 700 Raid Perc.
After connection, system says:
"Enclosed envelope does not support in the direct mapping of the controller mode.
Please contact your system.
System was interrupted because of the supported configuration. »
I replaced the H700 raid, then wire and FW update. System not notification but after press Ctrl + R, perc raid h700 not detect any hard disk.
Please help me!
TKS!
TrungDV
The issue is due to backplane having a bad rider on the expansion of the plant. To correct this remove J15 the C2100 3.5 "bottom of basket, or backplane C2100 2.5 J7". Refer to the below pictures to help locate the jumpers.
3.5 "
2.5 "
Let me know if this helps solve the problem.
-
Windows Update does not detect the sp1.
Hi all.
I do update windows via the control panel and its been so many updates, but it does not detect any service packs.
Anyone know what I can do to solve the problem?My computer is a compaq presario with vista home premium.
Thank you.
Hello
Download SP1 or SP2 from the links below:
And then perform a clean boot and disable the antivirus, and then restart the computer.
Clean boot:
http://support.Microsoft.com/kb/929135Install the service pack, and then restart the computer.
Problem of Windows updates should get fixed after you install the service packs.
All the best!
-
XP Mode in Windows 7 does not detect the ATI Radeon graphics card
Hi, on windows 7, xp (virtual), the system mode does not detect my graphics (ATI Radeon HD4530). This card is indispensable to run a business application (multimedia program). Can you please help me.
Thank you, Christian.
* original XP mode with title - __Windows 7 - (virtual) with ATI radeon HD4530__Christian.* graphics card
Windows XP mode provides a virtual hardware platform to run XP programs. With the exception of some USB devices, it does not provide a direct access to the hardware on the host computer.
If you need to use your real graphics hardware in XP you will probably have to put in place a system to dual-boot and boot XP when necessary.
-
When you try to re - install Windows XP, it does not detect the hard drive.
Hi all. I tired to do a reinstall of Windows XP today. It seems to take a lot of time, and then I did a very stupid thing. I turned off the laptop that I had to go. Now when I try to start the laptop on the cd, I get as far the screen where I have to press on enter to install Windows XP pro on the system or press R to repair. The problem is that there is now no facilities to choose from in the box below and the system is not recognizing the hard drive. I can't even as much as the screen to format the drive. When I press ENTER to install windows xp, then I get a blue screen telling me that the system shuts down to protect my pc. Is anyone able to tell me what to do to solve this problem please. Thank you very much in advance for your help. Noel
original title: I did a stupid thing... Windows XP ProSounds like a hard drive problem then. Your drive is maybe defective. First of all, you can use the partition of diagnostic Dell (F12) for its determination.
In case there is a SATA problem, press F2 to enter the BIOS and change the setting of hard disk SATA to legacy. (Might as well try this first.)
-
Cannot start Windows 10 (Partition exists in the startup disk)
Right, I accept all first I did something stupid - I resized a partition. I resized my Mac OSX Partition but not changed the Windows/BOOTCAMP Partition. My MBP has no DVD/CDROM drive. OK with that of the road, I have browsed these forums for centuries and can not find how to re - add the partition to the boot sequence. All files etc are in the score, and it is an option in 'Start Up' disc. It is not just show when booting with the down option. Orders/Info added on similar topics:
diskutil list /dev/disk0 (internal, physical): #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.3 GB disk0 1: EFI EFI 209.7 MB disk0s1 2: Apple_HFS Macintosh HD 330.2 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 4: Apple_HFS Untitled 24.1 GB disk0s4 5: Microsoft Basic Data BOOTCAMP 145.0 GB disk0s5
sudo fdisk -e /dev/disk0 fdisk: could not open MBR file /usr/standalone/i386/boot0: No such file or directory
diskutil cs list No CoreStorage logical volume groups found
sudo gpt -vv -r show /dev/disk0 Password: gpt show: /dev/disk0: mediasize=500277790720; sectorsize=512; blocks=977105060 gpt show: /dev/disk0: PMBR at sector 0 gpt show: /dev/disk0: Pri GPT at sector 1 gpt show: /dev/disk0: Sec GPT at sector 977105059 start size index contents 0 1 PMBR 1 1 Pri GPT header 2 32 Pri GPT table 34 6 40 409600 1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B 409640 644830816 2 GPT part - 48465300-0000-11AA-AA11-00306543ECAC 645240456 1269536 3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC 646509992 47131224 4 GPT part - 48465300-0000-11AA-AA11-00306543ECAC 693641216 262144 693903360 283201536 5 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 977104896 131 977105027 32 Sec GPT table 977105059 1 Sec GPT header
Other points
- If I try to use 'Start Up' drive to restart Windows, it does not work, I just get a black screen.
- Due to the configuration that I can't really afford to reinstall everything on a new partition I would everything white / software installed, install Windows 7, upgrade to 10, reinstall various licenses etc, it would take me 2 days and my schedule does not allow for this.
- I went through many discussions of the forum here: my background is software/web, no hardware, so the command line is a bit strange for me, but I can follow the instructions I have not successfully updated my "products" but I'm still on a MBP of the retina, the current captain.
Please help me get out of a mess in that I have unintentionally! Thank you!
I finally found this answer of the LonerT who fixed this issue for me https://discussions.apple.com/message/29579529#29579529 thank you!
-
does not detect external hard disk
Hey guys
Recently I update my macbook pro (2014) in the sierra of mac os. Since then, my mac does not detect any external hard drive I plug in it even if these drives are detected by the PC and all the files inside. I tried to open utility disk where the hard drive is displayed but the 'volume' located below is gray. When I try to hit mount said volume that nothing happens. All I could do to fix this?
Thank you in advance.
Hi sgerolio,
I understand that you are unable to detect any external drive that you plug into your MacBook Pro, since you upgraded to macOS Sierra. How many external hard drives work? How they are formatted? If formatted for PC, they would not necessarily be able to be read by a Mac.
You have a small empty external drive or USB key that you can test? Formatted in Mac OS extended (journaled). Using the Finder, you are able to see the external drive and drag a file to it?
The title of the article includes the Aperture application but apply these tips to format an external hard drive to any software application.
Drives external format Mac OS extended before using with opening
Take care.
Maybe you are looking for
-
Siri does not not on Apple TV remote
I bought an Apple TV (4th gen) on the release and everything worked perfectly. A few days earlier, Siri has stopped working on the remote control. I press the button Siri, it appears on the screen, but it does not recognize my voice commands. It's
-
Pavilion g6 - 2215so: Pavilion g6 Administration Password / power on password
Hello. I have a problem starting my laptop. Have not used for some time since I bought a new one, but now I wanted to transfer all my files to the new laptop, but when I run my old one some type of blue of the BIOS password is displayed, I don't know
-
In previous versions of FF there used to be a small arrow which, if you click on it, displays a history list. I can't find where this function is in FF V4.
-
How to upload photos from mobile phone on craigslist
* Original title: how taking mobile phone pictures snd put them on craigslist ad? I have pictures on my cell phonr I want to place an ad from craigslist. What are the steps? Thank you!
-
This license to use for the banks of the device Indian co
If the Bank is already a licensee for Windows now this license should be used for the renewal. (Indian co-operative bank)