Cannot telnet ASA VPN remote

Similar Questions

• ASA ASA VPN remote access

  This is my first post on this site. Hi all!

  I have not really set up ASAs or VPN on Cisco devices before. Currently, I'm trying to configure a dial-up VPN between ASA devices, a 5505 and a 5510. The 5510 is supposed to be the server and the 5505 is supposed to be the easyvpn customer. The reason why I'm opting for remote access instead of site to site is that I much 5505 s on the remote I need to set up in the future, and they will be moving around a bit (I prefer not to have to follow the configs to site to site). The 5510 is not mobile. The ASA devices are able to ping to 8.8.8.8 as ping each other in the face of public IP address.

  Neither SAA can ping IP private of other ASA (this part makes sense), and I am unable to SSH from a client on the side 5510 for internal interface (192) of the 5505. I wonder if someone more experienced in the remote VPN ASA than me is able to see something wrong with my setup? I glued sterilized configs of two ASAs below.

  Thanks a lot for any assistance!

  ASA 5510 (server)

  ASA Version 8.0 (4)

  !

  hostname ASA5510

  domain name

  activate the password encrypted

  passwd encrypted

  names of

  !

  interface Ethernet0/0

  nameif outside

  security-level 0

  IP 48.110.3.220 255.255.255.192

  !

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 192.168.191.252 255.255.252.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain name

  permit same-security-traffic intra-interface

  permit NONAT_VPN to access extended list ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0

  VPN_REMOTE_IPS note EZ VPN REMOTE IP access-list VARIES

  permit VPN_REMOTE_IPS to access extended list ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 613.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside) 0-list of access NONAT_VPN

  Route outside 0.0.0.0 0.0.0.0 48.110.3.193 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.0.0 255.255.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-aes-192 TestVPN, esp-sha-hmac

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec kilobytes of life - safety 4608000 association

  Crypto dynamic-map DYNAMIC - map 5 game of transformation-TestVPN

  86400 seconds, crypto dynamic-card DYNAMIC-map 5 the duration value of security-association

  cryptographic kilobytes 4608000 life of the set - the association of the DYNAMICS-Dynamics-card card 5 security

  outside_map card crypto 86400 seconds, 1 lifetime of security association set

  card crypto outside_map 1 set security-association life kilobytes 4608000

  card crypto S2S - VPN 100 set security-association second life 86400

  card crypto S2S - VPN 100 set security-association kilobytes of life 4608000

  card crypto OUTSIDE_MAP 65530-isakmp ipsec DYNAMIC-map Dynamics

  OUTSIDE_MAP interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 1

  SSH 192.168.0.0 255.255.0.0 inside

  SSH timeout 15

  Console timeout 30

  management-access inside

  priority-queue outdoors

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  internal EZVPN_GP group policy

  EZVPN_GP group policy attributes

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_REMOTE_IPS

  allow to NEM

  username password encrypted privilege 3

  username password encrypted privilege 15

  type tunnel-group EZVPN_TUNNEL remote access

  attributes global-tunnel-group EZVPN_TUNNEL

  Group Policy - by default-EZVPN_GP

  IPSec-attributes tunnel-group EZVPN_TUNNEL

  pre-shared key

  !

  class-map inspection_default

  match default-inspection-traffic

  VOICE-CLASS class-map

  match dscp ef

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map PRIORITY_POLICY

  class CLASS VOICE

  priority

  matches of the QOS-TRAFFIC-OUT strategies

  class class by default

  average of form 154088000

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:10156ad7ab988ae7ed66c4b6d0b4712e

  : end

  ASA 5505 (Client)

  ASA Version 8.2 (5)

  !

  ASA5505 hostname

  activate the password encrypted

  passwd encrypted

  names of

  !

  interface Ethernet0/0

  !

  interface Ethernet0/1

  switchport access vlan 2

  !

  interface Ethernet0/2

  Shutdown

  !

  interface Ethernet0/3

  Shutdown

  !

  interface Ethernet0/4

  Shutdown

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.19.1 255.255.255.192

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 174.161.76.217 255.255.255.248

  !

  passive FTP mode

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Route outside 0.0.0.0 0.0.0.0 174.161.76.222 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.0.0 255.255.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  Telnet timeout 5

  SSH 192.168.0.0 255.255.0.0 inside

  SSH 48.110.3.220 255.255.255.255 outside

  SSH timeout 5

  Console timeout 0

  management-access inside

  vpnclient Server 48.110.3.220

  vpnclient mode network-extension-mode

  vpnclient EZVPN_TUNNEL vpngroup password

  vpnclient username password

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  username password encrypted privilege 15

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  destination http address

  https://Tools.Cisco.com/its/service/odd... DCEService

  email address of destination

  [email protected] / * /.

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:bd465cea07c060a409a2eade03b487dc

  : end

  Please follow this link to create a dynamic L2L Remote Server on ASA5510.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

  Here is a link for you to create the Site to Site vpn tunnel and the tunnel can be customer above tunnel dynamic L2L Server.

  http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml

  Hope that helps.

  If you have any questions, please ask.

  Thank you

  Rizwan James

• ASA 5505 VPN remote cannot access with my local network

  Hello guys, I have a problem with my asa 5505 remote VPN access to the local network, the VPn connection works well and connected, but the problem is that I can't reach my inside connection network of 192.168.30.x, here's my setup, please can you help me

  ASA Version 8.2 (1)

  !

  !

  interface Vlan1

  nameif inside

  security-level 100

  192.168.30.1 IP address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 155.155.155.10 255.255.255.0

  !

  interface Vlan5

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  inside_nat0_outbound list of allowed ip extended access any 192.168.100.0 255.255.255.240

  pager lines 24

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool vpn-pool 192.168.100.1 - 192.168.100.10 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  Mull strategy of Group internal

  attributes of the Group mull strategy

  Protocol-tunnel-VPN IPSec

  username privilege 0 encrypted password eKJj9owsQwAIk6Cw xxx

  VPN-group-policy Mull

  type mull tunnel-group remote access

  tunnel-group mull General attributes

  address vpn-pool pool

  Group Policy - by default-mull

  Mull group tunnel ipsec-attributes

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  !

  global service-policy global_policy

  context of prompt hostname

  Yes, you will need to either configure split tunnel so that internet traffic goes out through your local Internet service provider, GOLD / directed by configuration current you are tunneling all traffic (internet traffic Inc.) to the ASA, then you will need to create NAT for internet traffic.

  To set up a tunnel from split:

  split-acl access-list allowed 192.168.30.0 255.255.255.0

  attributes of the Group mull strategy

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split-acl

  I hope this helps.

• Cisco ASA, connect an IP address on the OUTSIDE of the VPN remote access

  Hello

  I tried to find resources on the net but could not find a solution, then post it here. Maybe someone can help.

  So the problem is that I'm trying to access a server on the cloud for remote VPN access (cisco asa 5510).

  The server on the cloud (54.54.54.54) is only accessible from the outside interface (192.168.11.2) NY Firewall (cisco asa 5510)

  I added some ACE for this in the ACL of VPN tunnel to divide.

  NY-standard host allowed fw # access - list vpn_remote-customer 54.54.54.54

  And I see the road added to my cliet machine after the VPN connection, but still it cannot connect to this server.

  The network INTERIOR, I can connect to the server.

  

  Thanks in advance.

  Hello

  This is most likely a problem with NAT hair/U-turn hairpin.

  Will need to see the configurations or you would need to check yourself

  I don't know what your version of the Software ASA is to be like who determines what is the format of NAT configuration.

  So far, you have confirmed that the ASA VPN configuration provides the VPN Client with the route to the remote server. Then in circulation should be tunnel to the ASA.

  Then, you will need to check the output of this command

  See the race same-security-traffic

  You should see the command in the output below

  permit same-security-traffic intra-interface

  If you do not, you will need to add it. This effect of controls is to allow traffic to enter an interface and exit through the same interface. In your case this applies to Internet VPN Client traffic to the remote server as it between ' outside ' and spell through the 'outside'.

  Then, should ensure that dynamic PAT is configured for the VPN Clients.

  8.2 software (and below)

  You most likely have a dynamic configuration PAT like that on the firewall, if levels of above running software version

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0

  In this situation if we wanted to add dynamic PAT for a pool of VPN, we would add

  NAT (outside) 1

  This would allow users to use the same public IP address as LAN users, when accessing the remote VPN server

  Software 8.3 (and above)

  Because the NAT configuration format is completely different in the latest software, you could probably just add a new configuration of NAT completely without adding a

  network of the VPN-PAT object

  subnet

  dynamic NAT interface (outdoors, outdoor)

  Of course, its possible that there could be some configuration NAT already on the device which could cause problems for this configuration. If this does not work then that we would have to look at the actual configurations on the ASA.

  Hope this helps

  Let me know how it goes

  -Jouni

• IPSec Tunnel site to Site between ASA (static IP) to the firewall Microtick (dynamic IP) cannot telnet routeros and open https

  I purchased Mikrotik hardware devices and want to use routeros seat firewall cisco asa establish VPN. Aims to establish that a branch may be two IPSEC VPN access devices at the headquarters of the server via the public network.

  But now, I'm having some trouble, so I have cisco asa branches and headquarters to establish successful ipsec vpn.
  (1) branch routeros WAN port using a private IP address and is a member of the asa above outdoor sound created vpn ipsec, vpn successfully established internal servers and I ping the switch at the headquarters of the branch. However, there is a problem, I go through routeros visit that the headquarters of the https server pages can not be opened, telnet internal switches can telnet to the top, but were unable to penetrate into the character.
  (2) in addition, I left the branch routeros on a public IP address WAN port and asa VPN IPSEC created seat, said problems above are not, the server can also be accessed, telnet switch can also enter text and control.
  At the present time, I have encountered this problem of interface not CAN not because I need to create of very, very many industries and the need to establish headquarters communications branch offices so I have to use private IP addresses to access the Wan, unable to do wan are public IP address and headquarters to establish IPSEC VPN.

  now, I can't telnet asa inside the cisco router and open the web inside https, I can't solve the problems.

  now, registrants of asa:

  interface GigabitEthernet0/0
  nameif outside
  security-level 0
  IP 49.239.3.10 255.255.255.0
  !
  interface GigabitEthernet0/1
  nameif inside
  security-level 100
  IP 172.17.0.111 255.255.255.0

  network of the object inside
  172.17.1.0 subnet 255.255.255.0
  network outsidevpn object
  Subnet 192.168.0.0 255.255.0.0

  QQQ

  NAT (inside, outside) static source inside inside destination static outsidevpn outsidevpn non-proxy-arp-search to itinerary

  Route outside 0.0.0.0 0.0.0.0 49.239.3.1 1
  Route inside 172.17.1.0 255.255.255.0 172.17.0.5 1

  Crypto ipsec transform-set esp-3des esp-md5-hmac ikev1 cisco
  Crypto ipsec pmtu aging infinite - the security association
  Crypto dynamic-map cisco 1000 set pfs
  Crypto dynamic-map cisco 1000 set transform-set cisco ikev1
  Crypto dynamic-map cisco 1000 value reverse-road
  Cisco-cisco ipsec isakmp dynamic 1000 card crypto
  cisco interface card crypto outside
  trustpool crypto ca policy
  Crypto isakmp nat-traversal 60
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  IPSec-attributes tunnel-group DefaultL2LGroup
  IKEv1 pre-shared-key *.

  Hello

  Could you share the output of the counterpart of its IPSec cry see the 49.239.3.10 of the other device?

  Kind regards

  Aditya

• PORT of Configuration.DEFAULT of ASA AnyConnect remote VPN access.

  Hello!!! Now, I need to configure the AnyConnect VPN remote access. And I have a question.

  The default 443 AnyConnect port, but the port is occupied on SAA. We use this port for another application.

  How to change the port to connect? Is this true? Thank you!!!

  Hi, please add the following configuration:

  1. Enable the WebVPN on the SAA feature:

     ASA(config)#webvpn

  2. Enable WebVPN services for the external interface of the ASA:

     ASA(config-webvpn)#enable outside

  3. Allow the ASA to listen WebVPN traffic on the custom port number:

     ASA(config-webvpn)#port <1-65535>

• Site to Site and together on ASA 5505 VPN remote access

  Hello

  I tried to set up a VPN Site again on an ASA5505 where there already is a VPN remote on it.

  After you add the new configuration lines, I received the following message when I debug:

  04 Nov 07:06:06 [IKEv1]: group = , IP = , error QM WSF (P2 struct & 0xd91a4d10, mess id 0xeac05ec0).

  04 Nov 07:04:36 [IKEv1]: group = , IP = , peer of drop table Correlator has failed, no match!

  Someone knows what's the problem? And what to change in the config?

  Thanks in advance,

  Ruben

  Hello

  If the ASA had a remote access VPN and you add a new Site-to-Site you must make sure that the priority for the card encryption is weaker for the new Site-to - added Site.This is because otherwise traffic will always try to match the access tunnel at distance. You can check it with the command "sh run card cry"

  Federico.

• Impossible to disable Easy VPN remote for ASA 5505 6.4 AMPS

  When installing ASA 5505, we chose Easy VPN remote.  Now, we want to turn it off.  We go to Configuration in ASDM > remote access VPN > Easy VPN remote and try to clear the checkbox enable Easy VPN remote, but it will not uncheck.  How can we disable it?

  ASDM, go in tools--> command line Interface...--> and then enter 'without activating vpnclient'--> the button 'send '.

  Which will disable the Easy VPN remote on the SAA.

  Hope that helps.

• remote VPN and vpn site to site vpn remote users unable to access the local network

  As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

  The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

  ASA Version 8.2 (2)
  !
  host name
  domain kunchevrolet
  activate r8xwsBuKsSP7kABz encrypted password
  r8xwsBuKsSP7kABz encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  PPPoE client vpdn group dataone
  IP address pppoe
  !
  interface Ethernet0/1
  nameif inside
  security-level 50
  IP 192.168.215.2 255.255.255.0
  !
  interface Ethernet0/2
  nameif Internet
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  management only
  !
  passive FTP mode
  clock timezone IST 5 30
  DNS server-group DefaultDNS
  domain kunchevrolet
  permit same-security-traffic intra-interface
  object-group network GM-DC-VPN-Gateway
  object-group, net-LAN
  access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 Internet
  IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  AAA authentication enable LOCAL console
  LOCAL AAA authentication serial console
  Enable http server
  x.x.x.x 255.255.255.252 out http
  http 192.168.215.0 255.255.255.252 inside
  http 192.168.215.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 65500 transform-set RIGHT
  card crypto 10 VPN ipsec-isakmp dynamic dynmap
  card crypto VPN outside interface
  card crypto 10 ASA-01 set peer 221.135.138.130
  card crypto 10 ASA - 01 the transform-set RIGHT value
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  the Encryption
  sha hash
  Group 2
  lifetime 28800
  Telnet 192.168.215.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside
  VPDN group dataone request dialout pppoe
  VPDN group dataone localname bb4027654187_scdrid
  VPDN group dataone ppp authentication chap
  VPDN username bb4027654187_scdrid password * local store
  interface for identifying DHCP-client Internet customer
  dhcpd dns 218.248.255.141 218.248.245.1
  !
  dhcpd address 192.168.215.11 - 192.168.215.254 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Des-sha1 encryption SSL
  WebVPN
  allow outside
  tunnel-group-list activate
  internal kun group policy
  kun group policy attributes
  VPN - connections 8
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  kunchevrolet value by default-field
  test P4ttSyrm33SV8TYp encrypted password username
  username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
  username kunauto attributes
  Strategy Group-VPN-kun
  Protocol-tunnel-VPN IPSec
  tunnel-group vpngroup type remote access
  tunnel-group vpngroup General attributes
  address pool VPN_Users
  Group Policy - by default-kun
  tunnel-group vpngroup webvpn-attributes
  the vpngroup group alias activation
  vpngroup group tunnel ipsec-attributes
  pre-shared key *.
  type tunnel-group test remote access
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
  : end
  kunauto #.

  Hello

  Looking at the configuration, there is an access list this nat exemption: -.

  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

  But it is not applied in the States of nat.

  Send the following command to the nat exemption to apply: -.

  NAT (inside) 0 access-list sheep

  Kind regards

  Dinesh Moudgil

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• Create different group with VPN remote access

  Hello world

  The last time, I ve put in place a VPN for remote access to my network with ASA 5510

  I ve access to all my internal LAn helped with my VPN

  But I want to set up a vpn group in the CLI for a different group of the user who accesses the different server or a different network on my local network.

  Example: computer group - access to 10.70.5.X network

  Group consultant network - access to 10.70.10.X

  I need to know how I can do this, and if you can give me some example script to complete this

  Here is my configuration:

  ASA Version 8.0 (2)
  !
  ASA-Vidrul host name
  vidrul domain name - ao.com
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  DNS-guard
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  address IP X.X.X.X 255.255.255.X
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  address IP X.X.X.X 255.255.255.X
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Description Port_Device_Management
  nameif management
  security-level 99
  address IP X.X.X.X 255.255.255.X
  management only
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  DNS server-group DefaultDNS
  vidrul domain name - ao.com
  access-list 100 scope ip allow a whole
  access-list extended 100 permit icmp any any echo
  access-list extended 100 permit icmp any any echo response
  vpn-vidrul_splitTunnelAcl permit 10.70.1.0 access list standard 255.255.255.0
  vpn-vidrul_splitTunnelAcl permit 10.70.99.0 access list standard 255.255.255.0
  inside_nat0_outbound list of allowed ip extended access all 10.70.255.0 255.255.255.0
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 management
  IP local pool clientvpngroup 10.70.255.100 - 10.70.255.200 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 602.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 10.70.0.0 255.255.0.0
  Access-group 100 in the interface inside
  Access-group 100 interface inside

  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  Protocol RADIUS AAA-server 10.70.99.10
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication
  LOCAL AAA authorization command
  Enable http server
  http 192.168.1.2 255.255.255.255 management
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
  SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  the Encryption
  md5 hash
  Group 2
  life 86400
  Crypto isakmp nat-traversal 30
  Telnet 0.0.0.0 0.0.0.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  outside access management
  dhcpd manage 192.168.1.2 - 192.168.1.5
  dhcpd enable management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  class-map inspection_default
  match default-inspection-traffic
  block-url-class of the class-map
  class-map imblock
  match any
  class-map P2P
  game port tcp eq www
  !
  !
  type of policy-card inspect dns migrated_dns_map_1
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the migrated_dns_map_1 dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  Policy-map IM_P2P
  class imblock
  class P2P
  !
  global service-policy global_policy
  vpn-vidrul group policy internal
  vpn-vidrul group policy attributes
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
  value by default-field vidrul - ao.com
  test 274Y4GRAbNElaCoV of encrypted password privilege 0 username
  username admin privilege 15 encrypted password bTpUzgLxalekyhxQ
  attributes of user admin name
  Strategy-Group-VPN-vpn-vidrul
  username, password suporte zjQEaX/fm0NjEp4k encrypted privilege 15
  type tunnel-group vidrul-vpn remote access
  vpn-vidrul general-attributes tunnel-group
  address clientvpngroup pool
  Group Policy - by default-vpn-vidrul
  IPSec-vpn-vidrul tunnel group attributes
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:d84e64c87cc5b263c84567e22400591c
  : end

  What you need to configure is to imitate the configuration on the tunnel-group and group strategy and to configure access to specific network you need.

  Currently, you have configured the following:

  vpn-vidrul group policy internal
  vpn-vidrul group policy attributes
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
  value by default-field vidrul - ao.com

  type tunnel-group vidrul-vpn remote access
  vpn-vidrul general-attributes tunnel-group
  address clientvpngroup pool
  Group Policy - by default-vpn-vidrul
  IPSec-vpn-vidrul tunnel group attributes
  pre-shared-key *.

  What you need is to create new group policy and the new tunnel-group and configure the tunnel split ACL to allow access to specific access required.

  The user must then connect with the new group name and the new pre-shared key (password).

  Hope that helps.

• Assign the static IP address by ISE, ASA VPN clients

  We will integrate the remote access ASA VPN service with a new 1.2 ISE.

  Authentication is performed in Active directory. After authentication, can address assigned to a specific user of VPN by ISE IP?

  This means that the same VPN user will always get the same IP address. Thank you.

  Daniel,

  You can override the IETF-RADIUS-Framed-IP-Address in the authorization policy.

  However if I may make a suggestion:

  Unless you have only a handful of users to do so, it may be appropriate to assign the address of ISE pool or perform the mapping of LDAP attributes on ASA itself.

  In the latter case, the IP addresses are kept on the server as LDAP attributes and ASA will map the IP address. You don't want to keep address IP DB in several places.

  M.

• Device behind a Firewall other, ASA VPN

  I have a client who wants to put their VPN / behind the ASA ASA main connected to the Internet.  Both devices have an inside leg for the internal network, but the ASA VPN connects directly to the Internet ASA.

  Topology:

  Outisde FW: Internet transfer Procedure > ASA/FW > leg DMZ to ASA/VPN

  ASA VPN: Outside the L3 Interface interface DMZ of ASA/FW link

  On the outside NAT FW I would be the external address of the VPN / ASA outside the public IP address is available and I have a rule that allows all IP from outside to outside the private IP VPN.  Inside = 192.168.254.1 outside = public IP address.

  Configured on the VPN / ASA, ASA standard SSL Remote Access.

  When I hit the NAT public IP address, nothing happens.  I've run packet - trace on the FW outside, and everything seems good.

  Someone at - it a sampling plan / config for a similar topology?     Internet > ASA/FW > dmz-leg > ASA/VPN

  Thanks in advance,
  Bob

  Can share you your NAT and routing configuration? Of these two ASAs

• The anyconnect vpn easy vpn Remote communication problem

  Hi team,

  I have a problem of communication of the anyconnect vpn easy vpn Remote I´ll explain better below and see the attachment
  topology:

  (1) VPN Tunnel between branch HQ - That´s OK
  (2) VPN Tunnel between Client AnyConnect to HQ - that s OK

  The idea is that the Anyconnect Client is reaching the local Branch Office network, but has not reached.
  Communication is established just when I begin a session (icmp or rdp) branch to the AnyConnect Client,.
  in this way, the communication is OK, but just for a few minutes.

  Could you help me?
  Below the IOS version and configurations

  ASA5505 Version 8.4 (7) 23 (Headquarters)
  ASA5505 Version 7.0000 23 (branch)

  Configuration of the server easy VPN (HQ) *.

  Crypto dynamic-map DYNAMIC - map 5 set transform-set ESP-AES-256-SHA ikev1
  Crypto card outside-link-2_map 1 ipsec-isakmp DYNAMIC-map Dynamics
  Crypto map link-outside-2_map-65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  Crypto map interface outside-link-2_map outside-link-2

  ACL_EZVPN list standard access allowed 10.0.0.0 255.255.255.0
  ACL_EZVPN list standard access allowed 192.168.1.0 255.255.255.0
  ACL_EZVPN list standard access allowed 192.168.50.0 255.255.255.0
  ACL_EZVPN list standard access allowed 10.10.0.0 255.255.255.0

  internal EZVPN_GP group policy
  EZVPN_GP group policy attributes
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list ACL_EZVPN
  allow to NEM
  type tunnel-group EZVPN_TG remote access
  attributes global-tunnel-group EZVPN_TG
  Group Policy - by default-EZVPN_GP
  IPSec-attributes tunnel-group EZVPN_TG
  IKEv1 pre-shared-key *.

  object-group network Obj_VPN_anyconnect-local
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.15.0 255.255.255.0
  object-group network Obj-VPN-anyconnect-remote
  object-network 192.168.50.0 255.255.255.0
  the NAT_EZVPN_Source object-group network
  object-network 192.168.1.0 255.255.255.0
  object-network 10.10.0.0 255.255.255.0
  the NAT_EZVPN_Destination object-group network
  object-network 10.0.0.0 255.255.255.0
   
  destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.

  Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
  destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static

  NAT_EZVPN_Destination no-proxy-arp-search to itinerary
  NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination

  NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route

  Configuration VPN AnyConnect (HQ) *.

  WebVPN
  Select the outside link 2
  by default-idle-timeout 60
  AnyConnect essentials
  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
  AnyConnect profiles Remote_Connection_for_TS_Users disk0: / remote_connection_for_ts_users.xml
  AnyConnect enable
  tunnel-group-list activate

  tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.15.0 255.255.255.0
  tunnel of splitting allowed access list standard 10.0.0.0 255.255.255.0

  internal clientgroup group policy
  attributes of the strategy of group clientgroup
  WINS server no
  value of server DNS 192.168.1.41
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  ipconnection.com.br value by default-field
  WebVPN
  AnyConnect Dungeon-Installer installed
  time to generate a new key 30 AnyConnect ssl
  AnyConnect ssl generate a new method ssl key
  AnyConnect value Remote_Connection_for_TS_Users type user profiles
  AnyConnect ask flawless anyconnect

  type tunnel-group sslgroup remote access
  tunnel-group sslgroup General-attributes
  address vpnpool pool
  authentication-server-group DC03
  Group Policy - by default-clientgroup
  tunnel-group sslgroup webvpn-attributes
  enable IPConnection-vpn-anyconnect group-alias

  object-group network Obj_VPN_anyconnect-local
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.15.0 255.255.255.0
  object-group network Obj-VPN-anyconnect-remote
  object-network 192.168.50.0 255.255.255.0
  the NAT_EZVPN_Source object-group network
  object-network 192.168.1.0 255.255.255.0
  object-network 10.10.0.0 255.255.255.0
  the NAT_EZVPN_Destination object-group network
  object-network 10.0.0.0 255.255.255.0
   
  destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.

  Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
  destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static

  NAT_EZVPN_Destination no-proxy-arp-search to itinerary
  NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination

  NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route

  Hello

  communication works when you send the traffic of easyvpn derivation because it froms the IPSEC SA to pool local subnet and anyconnect HQ. The SA formed only when the branch initiates the connection as it's dynamic peer connection to HQ ASA.

  When there no SA between branch and HQ for this traffic, HQ ASA has no idea on where to send the anyconnect to network traffic.

  I hope this explains the cause.

  Kind regards

  Averroès.

• New ASA/VPN configuration

  So, I am looking to add one of my spare 5510 firewall to my secondary network as a vpn connection.

  All I want this new ASA to do is handle my site anyconnect VPN connections.  I'm pretty new to ASAs if any help would be great.  I know how to create a new access VPN on my ASA and I added a NAT for my inside and outside traffic to my new Pool of IP VPN.

  My question is, since it's only for the VPN and I want all my current internal traffic to continue to the asa 5510 existing routing, do I have to enter the ACL to my new single AAS of VPN?  ACLs are used for VPN traffic and do I need them to traffic the route via VPN?

  I'll put up inside interface of connection to one of my main Cisco switches and the outside interface connects to my DMZ switch on the new ASA only VPN.

  Thank you

  I don't know if I am how you connect to the external interface of single ASA VPN. Normally, in this type of installation, we would see the ASA VPN "in parallel" with the perimeter firewall.

  You mention the DMZ switch that threw me a little. If you are in France through your main firewall and go to single ASA VPN via the DMZ then Yes you will need to allow several open ports (protocol 50, udp/500, tcp/443 among others) and may have to do some other techniques (NAT - T, etc.) depending on the type of remote you are implementing. That's why we rarely see this configuration used - it adds a good dose of complexity without significant benefit.

  When the old facility is used, you need to switch internal to know to route traffic to the pool VPN through the only ASA VPN inside the interface. A static route is more often used, although you can use OSPF or EIGRP if you wanted to.

  Should generally not be any access list that VPN traffic around the Bank access lists incoming interface. Back to remote clients traffic is coming from inside and out through (and is usually part of anestablished connection) so no access list is necessary inside.

• ASA5520 migration pool VPN remote access

  Hi all, looking for an entry in the best way to migrate to a new pool to access remote a DHCP address assignment.  We currently use a 24 pool, allowing us to 253 IP addresses... during the recent hurricane, we reached 250 used IP addresses and had to start asking users to connect to our device ASA VPN to another country, not an ideal solution.  I would like to extend our current VPN subnet to a 23, but I'm not a free 24 subnet above (or below) our current 24 subnet.

  I can certainly affect a new/23 subnet, but I'm looking for the best with minimal downtime migration plan (no interruption of service would be better).  Can I just add the new range of pool to the section of general-attributes tunnel-group RAVPN the current pool, or should I remove the old swimming pool, disconnect all remote access VPN users and have them reconnect to start to use the new pool?

  We run ASA Version 8.2 (1).

  Thank you!

  Hello

  I need to confirm (EDIT: checked everything in writing it) myself that I have not needed to do this before, BUT to my knowledge, you should be able to assing more of a DHCP pool on a single Client VPN connection.

  Please check the Cisco ASA command reference for 8.2

  VPN configuration pool under Tunnel-group configurations

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/command/reference/A2.html#wp1656186

  VPN configuration pool under Group Policy configurations

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/command/reference/A2.html#wp1660582

  They are in fact at the same location in the same document.

  Seems to me that there should be no problem to add another 24 pool to your Client VPN configurations (and do the necessary ACL / NAT Configurations)

  -Jouni