Card clocked at 75 idling

Similar Questions

• Satellite L640 - clock stuck CPU idle time

  Hi people, I have a Satellite L640 PSKOLA, with a processor i5 480M and am under Win7 64 bit, I have a "CPU usage" widget on the desktop, because clearly, I'm kinda a nerd. I first noticed this problem for a long time, but my usage has changed more things graphics lately and if it interferes with what I'm doing now.

  The clock on the CPU freezes at 1173 MHz, this happens only after the machine has been for a while and will be rectified by doing a reset, after which the clock fortunately returns a maximum of 2667 MHz and the changing dynamic clock works as it should, and I enjoy my machine once more, until it happens again which could be any time, but it usually takes at least a couple of hours.

  I hoped that would fix it, install the latest drivers but that didn't work, I reinstalled the version 2.3 BIOS update (the more recent on the toshiba site) and I installed it three times because I thought it might have been a glitch there.

  Any ideas?

  > On the CPU clock freezes at 1173 MHz, this only occurs after the machine sat for awhile

  How did you test this? Have you tested this using the CPU on the desktop gadget?
  Are you sure that this software works correctly? I think that no one should trust a single value provided by a program/utility.
  Use of different tools which can give different results

  However, the fact is that i5 480M processor supports Enhanced Intel SpeedStep technology.

  This technology allows the processor clock speed to be changed dynamically. This reduces to a minimum power draw and heat dissipation.
  A processor running at a high clock speed allows better performance.
  Using the same processor at a lower frequency (speed), it generates less heat and consumes less energy. This is controlled by the Enhanced Intel SpeedStep technology.
  I think this may be one of the reasons for this different CPU speed (perhaps the main reason).

• Card FPGA and data acquisition synchronization

  Hi, we are control and data acquisition of several hardware devices (including Photodetectors and translational stages). Until last week, we used all the controls and acquisition using a PCIe-7852R FPGA board. However, we decided to move the acquisition part to a PCIe 6363 DAQ card to improve the sharpness of the tension. During the test, I found that the internal clocks in the FPGA and the DAQ cards are slightly inconsistent (not just a phase delay, but a difference in the period).

  I know because I have generated a square wave (period = 20) using the FPGA and gains using the data acquisition card (at a rate of 200 kHz, that is, 1 taste every 5). I have observed acquired place shifts 5 every 5 seconds approximately. Such a change does not occur if the production and acquisition is done using the same Board. Therefore, the only explanation is that the data acquisition and FPGA cards clock frequencies are different. According to my calculations, the percentage difference between their time clock must be 5/5 s = 0.0001%.

  Therefore, I wonder if there is anyway to synchronize clocks between them. Or, is it possible that I can drive the FPGA clock-based DAQ hardware, or vice versa? Also, please let me know if there is something trivial as I fix.

  Thank you very much.

  Kind regards

  Varun

  Hi Varun,

  my post was only one solution...

  Your data acquisition card may take an entry to control sampling of trigger. In this mode, samples draw on a rising edge of the external clock signal. As long as you stay within the limits of the DAQ (100 MHz for your card) material sampling works perfectly. There are even examples coming with LabVIEW explaining how to program your data acquisition card...

  This mode use you your FPGA as clock source sampling for data acquisition. Both will run on the FPGA clock in sync. When the FPGA is a bit out of 40 MHz, so it won't matter because both devices are triggered on the same clock signal...

• Wireless connection lost after only five minutes

  Hello

  New on site, but you have a very annoying problem, here go us
  I just got a 2nd hand laptop Toshiba Satellite S1800-402 and has decided to add this to my setup wireless at home (big mistake), anyway I have a router wireless 802. 11 b of mentor and my main pc connected to the router and another pc which has a mentor 802 wireless pci card. 11B. Pcmcia card from the laptop is a mentor 802.11 g card is compatiable back, so I was told by bloke in-store pc.

  Just the problem I have is the pc successfully connect to internet the laptop will be fine OK, but 99% of the time I would say 5 minutes max before losing the connection and only way to get the rear connection is either reboot the laptop, or remove the pcmcia card and hope that it detects the wireless again. the wireless network is not secure on it and checked on the router page and there is no filtering or configure... I have Digital wireless home phones that I unplugged and get always the same problem.

  Would be - what this model has received a wireless card already and there is a conflict.

  It becomes a default really annoying that I head in fact.

  Any help would be greatly appreciated no matter what other requried info I will try to help

  Thanks in advance.

  Post edited by: sidog70

  Hello

  As much as I know this model doesn't have a WiFi card and this kind of conflict is not possible. In my opinion connection breaks are caused by software settings or false. If you make a permanent download happens the same thing?

  Try to check the power consumption of your network card WIRELESS and also Idle timeout option in the router.

• How can I check if the counter entry is synchronized with the analog output?

  Hello

  I'm working on an application for counting photons.  I use two channels of analog output on a PCI-6713 card to send a frame model to a set of XY scan mirrors.  I then a photon count unit that emits a TTL signal when the photons are detected as a result of this raster analysis.  I then use a surfboard USB-6211 to count the edges on this TTL signal.

  I have problems that seem due to synchronization problems.  I use the sample AO on the PCI-6713 card clock like the door of my meter on the map USB-6211.  I use a trigger to start digital to analog output and a trigger of arms for the entrance to counter early. Is there a way to check that the analog output and counter entry of start of operations at the same time and are are synchronized?  I basically want to monitor and compare the ao real sample of the PCI-6713 card clock door signal used by the jury of the USB-6211.  I was able to export the sample AO clock and watch it on my oscilloscope, but not the signal from the door of the USB-6211.

  Thanks for your help,

  Brian

  Update... It turns out that there is no problem of synchronization between my meter input and the analogue output.  There was a difference of impedance when I connected my unit of counting photons to my USB-6211.  This caused an error variable count rate.  After accouting for this shift, the problem disappeared.

• V3 571 g FAN

  After the upgrade to a 2.15 BIOS, my FAN acts stupid.

  It will not accelerate enough, the temperature rises and the low card clocks graphics making it imposible to play something for more than two minutes...

  

  Is it possible to downgrade to 2.13?

  See you soon

  At the present time, we do not provide a way for customers to downgrade a BIOS version, far from having the service system perform this particular operation.

  All versions of BIOS include previous corrections or adjustments in BIOS advance.

• VPN on Cisco 1841 router

  Hello

  I need to configure the vpn site to site on router cisco 1841, but the problem is that the router does not recognize the crypto comand.

  R1 #conf t
  Enter configuration commands, one per line.  End with CNTL/Z.
  R1 (config) #crypto?
  % Unrecognized command
  R1 (config) #crypto?
  % Unrecognized command
  R1 (config) #c?
  call call-history-mib id-carrier cdp
  chat script class-card clock SNC
  config-register connect plan control configuration

  R1 (config) #crypto isakmp policy 1

  ^
  Invalid entry % detected at ' ^' marker.

  R1 #sh worm
  Cisco IOS Software, 1841 (C1841-IPBASE-M), Version 12.4 (1 c), RELEASE SOFTWARE (fc1)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2005 by Cisco Systems, Inc.
  Updated Wednesday 25 October 05 17:10 by evmiller

  ROM: System Bootstrap, Version 12.3 T9 (8r), RELEASE SOFTWARE (fc1)

  the availability of CS-Khatlon-opio-01 is 2 days, 23 hours, 13 minutes
  System returned to ROM of charging at 16:07:44 TJK Friday, November 7, 2014
  System image file is "flash: c1841-ipbase - mz.124 - 1C.bin.

  Cisco 1841 (revision 6.0) with 114688K / 16384K bytes of memory.
  Card processor ID FCZ102110NQ
  2 FastEthernet interfaces
  Configuration of DRAM is 64 bits wide with disabled parity.
  191K bytes of NVRAM memory.
  31360K bytes of ATA CompactFlash (read/write)

  Configuration register is 0 x 3922

  Please help, how to set up vpn?

  Hello

  According to this output is more than clear that you do not have a k9 license applied to this router, this license will enable the security features on your IOS, in this case, you will need a permit of k9 with an activation key, and then you will be able to have available on your device encryption controls. Once you have that we can work on configuring site to site.

  Do not forget to rate!

  David Castro,

  Kind regards

• HP Compq dx2390 format microtour: GPU upgrade

  Abdoulaye, I HP Compq dx2390, and I want to buy a new GPU in the accessories page of dx2390 it is written that the recommended GPU is the Radeon HD 4650, because it can run on my PC which have only a 250W power supply.

  is it safe to upgrade to this map with a 250W?

  If your PC is spec'd for the ATI 4650 in option, then you are probably ready to go.  However, do not buy a card clocked.  In addition, open your PC and watch to see if a card full height will fit or you must use a low profile card.

• DAQmx: Outputs digital multiple tasks for the same card using the on-board clock

  I have a PCI - 6259 DAQ I'm programming with DAQmx. I want to create two tasks of digital output on the same card. A single task using on-board clock, continuous samples. The other task uses an onboard clock, finished samples and an external trigger with trigger Start.Retriggerable property = TRUE. Is this possible with my hardware and DAQmx? There will be a conflict if two tasks use the same clock source?

  This is not possible, you can have only one task timed materially by device.

  Best regards

• Synchronize the clocks of 2 PCI cards for analog inputs with e/s digital reference

  I'm trying to synchronize the clocks of reference of 2 PCI cards so that the analog inputs are synchronized. However, my appilcation has also digtial e/s on two cards, and who apparently made the mistake DAQmxErrorResourcesInUseForRoute_Routing. This discussion describes a similar problem, but the solution was to just put the reference clock to the slave device, who had no other tasks running on it, so what mine does.

  Is there way I can synchronize the clocks of refernce without interfering with the digital I/o?

  Thank you!

  PS: My application is in C++.

  The reference clock is really a lower-level component that is shared by all resources on a given device.  All tasks on a given device must use the same reference clock.  So if you use DAQmxSetRefClkSrc for a task, you can use it to set the same value for your other tasks.

  Best regards

• How to generate the clock 8,192 MHz on the labview FPGA 7854R series card?

  Hello

  I use the NI PXI-7854R series card that has 5 FPGA from Xilinx Vertex on him. I'm drifting clockwork 8,192 MHz to 40 MHz on board the FPGA clock. But he ended up giving me a single clock 8 MHz. is it possible to access the PLL located on FPGA Xilinx?

  Concerning

  If you are familiar with VHDL you can make your own "component-level IP' (aka CLIP) with a PLL Xilinx inside.  There are topics for help and examples of how to define a CLIP.  Here's one that shows how instantiate a DCM (similar to a PLL) in a CLIP:

  http://zone.NI.com/reference/en-XX/help/371599F-01/lvfpgahelp/fpga_clip_clock_ex_code/

• SP3 that my graphics card is idling at 100% of the activity.

  OK, I tried to install Windows Service pack 3 and after my XFX HD4650 graphics card idling at 100% of the activity. I have tried everything that I could to eliminate this problem, but the only thing that would fix it was to go back to SP2. The drivers are up to date. I even tried older drivers, but the map would be further slowed down to 100% of the activity. This in turn made games drags because of the ready-made card carried out by something in me SP3.

  Anyone know how to fix this?

  Well you need to update software/hardware drivers youre after SP3.

  Try to install the youre MB chipset installation utility, which removes (intel, amd, etc.).

  Update DirectX also.

  Once everything is done, if the problem persists, go to run, type: DXDIAG

  Run Direct X.

• Adobe send me notification on the credit card idle that my license will expire in a few days how I can now do my credit card is active already

  Adobe send me notification on the credit card idle that my license will expire in a few days how I can now do my credit card is active already

  Please see:

  Using creative cloud | 'Renew your membership' window appears when you launch a creative cloud application

  Re: The 10 Questions on the creation of clouds

  Re: "renew your membership".

  Hope this bhelps.

  Concerning

  Megha Rawat

• Idle curiosity #2: why reformat the camera SD card after each import?

  Many users are unhappy that their camera SD cards cause Photos or Image Capture to start whenever they insert or connect the card to their computers. I understand that this is caused by the fact that a reformatted SIM card is treated as a new 'device' and the previous settings does not launch applications is therefore null and avenue.

  My questions.

  Why users insist on reformat cards, rather than simply erase already imported files?

  It's just an old habit that is no longer necessary?

  FWIW, none of my cameras never asked me to reformat their storage cards. So, what gives?

  SIM cards cannot be formatted

• The weak T430 processor when Nvidia card using clock

  When I use any aplication with Nvidia card (Photoshop, 3D Max, etc.) or switch to external monitor (Display Port) my CPU is fixed to the minimum values: 1.15 Ghz.

  Why?

  What can I do? How to solve this problem?

  Help, please. This very important issue for me, because the work on this speed is impossible

  [T430, Core i5 - 3210M, Nvidia NVS5400, Windows 8 x 64 PRO]

  BigBlack, thank you! I had problem with Lenovo power management. Now I reinstall by using this statement and my laptop works at full speed (even 3 Ghz supported!)

  Problem solved.