Carpet * a DVD-RAM UJ-820 s does not work in Satellite M30X 122

Hello!

I am owner of a Satellite M30X - 122 Notebook with Mat * one reader CD DVD-RAM UJ-820 s.

In recent weeks the disc suddenly stops working during normal use, no error message, in Windows XP System Device Manager all entries are ok, the drive is enabled and visible.
!! Optical media access LED lites permanently, so that the reader is always available!
I have tried using different CD, reboot Notebook, removing battery State is always the same, LED blinks several times then it lites permanent.
After a few hours this phenomenon disapperars and I can use the drive without any problems. ! It is very annoying!

Someone at - it experience with this problem? Please let me know.

Don't you think that the drive needs to be replaced?
In this case (I tried a Mat * a DVD - RAM UJ-820 s on the www, I found none just renovated, new readers) does anyone know where to get a new, or a compatible UJ-820 s drive.

Thanks in advance.
Have a good evening.

Hello

I don't know where you live and can not recommend any PC shop but you can order it by the authorized service partner.

You can also view s manuals for Satellite M30X, and page 5, you will find a list of all compatible optical disk drives. Do not buy the same but much better if you want. I hope that this info will help you find the new drive.

Troubleshooting I can't say a lot. Try to remove the device from Device Manager and reboot the device and test again but with original media only. Make sure that you can see the contents of the CD or DVD using Windows Explorer.

If nothing is done check for replacement.

Tags: Toshiba

Similar Questions

  • Carpet * a DVD-RAM UJ-820 s does not recognize blank DVDs

    My laptop recently stopped recognizing blank, or I burned when I put them in the DVD player.
    The drive is a CARPET * a DVD-RAM UJ-820 s and it was working fine until last week when I tried to use the ASHAMPOO Burning software.

    He does not even recognize any MOVIE DVD I put in the drive, but it doesn't seem to have a problem with a music CD, I tried.

    Someone to help they could offer cause I'm running out of space and I really want to delete my files.

    Thank you

    Hello

    It looks a bit like a malfunction of the equipment. Maybe the lens of the drive can not calibrate correctly.

    Another clue;
    Have you tried to delete the upper and lower filter registry entries?
    Try it. Sometimes such procedure can simply bring the reader to life.

    The detailed procedure and description has been published here in the article Microsoft Knowledge base:
    http://support.Microsoft.com/kb/314060/en-us/

    Good luck

  • DVD-RAM UJ-820 s does not work on the Satellite A50 - 543

    Hello

    My present DVD-RAM UJ-820 s on Satellite A50 543 is not working correctly, original part is very expensive. Can I order to cheaper NEC AD - 7543A or NEC AD - 7540 A, but I don't know is it compatible with my Satellite A50 543 or not.

    Who can help me?
    Thanks in advance

    Hello

    From my experience not every disc is compatible with your laptop. It depends on the master / slave / parameters c - salt.
    The settings on the disks online slim for laptops is not editable as on desktop drives by putting the jumper.
    The thin line command does not support riders, and so the firmware controls the settings.

    But dnf666 already replaced the drive on sat 5200 and maybe your favorite player might be compatible

  • Carpet * a DVD-ram UJ-845 s does not work

    Hi everyone, I'm a little crazy for my dvd player, about 14 months I bought my 3rd toshiba laptop already.

    In the first (Satellite 5200) dvd player (combodrive with installation of dvd ram built in) has not already after a few months. I brought this back to Toshiba customer service twice and replace that thing (mast * a) twice as well... Then, the player broke down again.

    With the new Toshiba, I bought (Qosmio G20) I just got the same problems, dvd and cd function work correctly sometimes (unfortunately sometimes not as well), but the player (mast * a UJ-845 s, DL DVDwriter) recognizes not all all DVD ram.

    I hope someone can give me a hand with this problem, I'm really a little crazy about it now, and I don't want to keep running and visit the Toshiba Service Center every 2 / 3 months for the rest of my life...

    Thanks a lot anyway!

    Best regards, Erik

    Hi Erik

    It is very strange that you have problems with sides. Over the past 7 years, I worked on 5 different Toshiba laptops and I, but really never had no problem with the chance. I always use the same empty media TDK (DVD-R, DVD - RW and DVD-RAM). Everything works fine.

    I have always taken out of pre-installed software and use Nero since the beginning. I really put t understand why the DVD-RAM media are not recognized, but please do not forget the DVD-RAM driver is pre-installed correctly.

    Have you noticed that with the factory settings?

  • Carpet * a DVD-RAM UJ-850 s does not read blank media - need new firmware

    Hey I have a laptop Equium only around the age of 4 months.
    Had nothing but problems with the CARPET * A DVD-RAM UJ-850 s ATA Device drive.
    I need to know where I can get the update of the firmware.

    Firmware for it, that she will not read blank media.

    I agree with master... I don't know what kind of problems you have, but if the player doesn't work properly, it must be replaced. The warranty is certainly valid and the nearest authorized can help you with it.

    Maybe you made a mistake. Take your laptop to the nearest service and show them what you mean exactly. Here, we can only speculate what may be your problem.

  • Carpet * a DVD-RAM UJ-820 s will not read the cd rom cd-rom dvd

    OK, I read the other posts on these discs. Mine will play DVD movies and play them. It will not read the dvd ROM CD CD-ROM etc.
    This cannot be a hardware problem, it must be the software should not it?
    Can anyone help?
    Does anyone have information on how to remove these disks of the computer? Im sure I can install a new one myself if I really need to.
    Unfortunately the computer is just out of warranty

    Hi Robert,.

    Unfortunately, your problem sounds like a problem with the hardware with the optical drive. The player itself must be able to refocus its lenses to switch between DVD and CD formats, and also to pass the pressed DVD and DVD burned.

    I suggest you tyre remove the device from the Device Manager Control Panel, then restart your laptop so that the optical drive will be recognized as a new component hardware and Windows will then be re - install with standard drivers etc. If this does not work then it looks like a new drive will be necessary.

    Unfortunately you say not what model of laptop you have (the removal procedure is not the same in all cases), but in general if the car is equipped with in-house it is held in place with one or two screws accessible from the bottom of the laptop that should be removed first, then the optical drive can be slid out of its location.

    Kind regards

  • Carpet * a DVD-RAM UJ-820 s do not read or burn discs

    Hi, I'm Natalie and I need help with my problem that occurs.

    Operating system:
    Windows XP Home Edition
    Laptop Toshiba Satellite
    Model A75-S229
    Multi recorder drive: CD and DVD

    The problem that happens is that I can not get any CD or DVD to work when I put them. What is happening is he's trying to load but makes the window "Not responding", unless I have the disc, then everything will be fine. What is also involved, is that I can't burn discs at all, at any speed.

    Also, I would add, when I go to my computer > right click on the DVD - RAM drive > properties and under the general tab it states:

    Type: CD player
    file system: unknown

    I don't know if that's the problem...

    Can someone help me?

    HI Isabelle.

    Please check in the Device Manager to see if there is a problem with your optical drive. Normally this will be displayed as an exclamation point against the device.

    The fact that the file system is listed as "unknown" is because the drive could not read the format of the disc so that Windors Explorer cannot identify any file structure.

    Your problem could be something very simple like a lens dirty or a faulty device driver. It is not easy to tell from your description exactly what can be wrong, but I would say you try some of the easy options so try first to clean the lens, and if this does not resolve your problem, then try to remove the drive (Device Manager) and reboot for the device will be installed new.

    If all else fails, you will have checked player be an authorized Service partner.

    Kind regards

  • Carpet * Combo DVD player does not work on Satellite M30X

    I have a Satellite M30X with a combo DVD player.
    My drive I ve formatted, then I installed the readers on the recovery cd and one existing on the toshiba web site and the reader to continue to not be able to write on DVD´s.

    The installed drive is: mast * a DVD-ram UJ - 831 s.

    I used to be able to write all kinds of DVD.

    Do you have any suggestions?

    Thank you

    Armando

    Hello

    > I then installed readers on the recovery cd and one existing on the toshiba web site
    Do you mean the DVD-RAM driver?

    As far as I know using DVD-RAM disks in the DVD MULTI drive, data can be written so that the function to write data on discs CD-R/RW standard Windows XP is enabled.

    Then please check if the check CD option activate called this roll
    CD / DVD-> properties-> recording tab
    is enabled or disabled

    By the way; After using the recovery CD, you don't need to install additional drivers. The restore CD contains all the necessary drivers including an important run Notepad correctly.

  • carpet * a dvd - ram uj-820 s

    My satellite a60 don't overlay the carpet * a dvd - ram uj-820 s at all. The system said that it does not, or he says he broke. But I don't know that it is not broken. What should I do?

    Hi Justus,

    Check in the Device Manager to see if your DVD-RAM is displayed. If it is you can try the troubleshooting for her option.

    You can also try to remove the device and then re - start, in this way, the system should see the drive and reinstall.

    HTH

  • Sony DVD RW DW - Q85A Driver does not work

    We have a relatively old Sony Vaio (VGN-FS485B) with Windows XP operating system.  The topic CD/DVD driver (RW-DW-Q85A) does not work and the State of the specified device is the following: "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) ».  Unable to overcome difficulties following procedure of Troubleshooting Device Manager.

    Grateful for any advice.

    This article can help...

    http://support.Microsoft.com/kb/314060

    Tricky

  • USB ports, CD/DVD player, and Mike just does not work

    So I'm pretty sure that these things are happening at the same time, although there are risks my trying to troubleshoot the USB ports have contributed to the failure of the microphone (internal and will not capture sound) and cd/dvd drive (not open). Perhaps? It is true that I know little about these kinds of things, but I'm much less following the indications which is what I did to try to tackle the problem of USB port, which was the first I noticed. I followed all the advice I could find online for troubleshooting when all usb ports do not respond. I used Device Manager to disable in its regular and safe mode. I also uninstalled them all in both modes (even if they reinstall until I'm able to restart). I unplugged and wait 5, 10, 15 min etc. There was a difficulty mentioned about watching the. Mine and INF files do not contain the mentioned error. I'm tempted to all my files backup and restore the computer to factory settings, especially now that the CD/DVD player and the micro does not work. This would solve the problem? If these things are related? Could even restore settings because I can't have in the cd/dvd drive? It's a dell inspiron 1721, and it crushed while you restart for almost a whole day just all the time I've began to notice all these malfunctions. I really appreciate any guidance!

    Good so I solved all of these problems. I don't know what did the trick, but when I went back in the BIOS to re - activate the ports they have worked!

  • WiFi does not work on Satellite C-55-A - 14 G with a Win 8 64 bit OS

    My wifi does not work on Satellite C55 - A - 14 G 8 64-bit Windows.
    How can I fix?

    There is wifi on other computers, but not on this laptop.

    Hello

    You always win 8?
    Microsoft has already published the Win 8.1 System.
    It of recommended to update 8 Win Win 8.1 because different bugs have been fixed and new features have been added.

    The 8.1 update win is free and you can download the Microsoft Store update files.
    Please perform updates, such as recommended by Toshiba and essential update, the driver and tools.

    I guess that after updating the WLan would work properly.

  • Windows 7 Matshita DVD-RAM UJ - 825S failure does not.

    Drivers?

    Hello

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    Try this fix manually if the Fixit 314060 does not work
    http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

    Your CD or DVD drive is missing or is not recognized by Windows or other programs-
    a Mr Fixit
    http://support.Microsoft.com/kb/982116

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    for Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
    Vista installation after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
    Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
    do it right.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are
    the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and
    the correct registry entries for your car.

    Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
    as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
    the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry for your CD/DVD settings
    drive from someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
    nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

    DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
    devices and their properties in flat table, instead of the tree viewer
    http://www.NirSoft.NET/utils/device_manager_view.html

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • driver DVD update and there but does not work

    My HP laptop DVD player does not work properly. When I try to update the driver, it does state that it is updated and currently, but it will not allow the DVD player function. When I check the peripheral material, it gives an error CODE 19.  It says that the drivers do not work properly.  I tried to allow the installation of HP Assistant driver and everything imaginable but nothing helps.

    It ends up being a higher filter problem in the registry to have two software for DVD.  It's corrected now.

  • After upgrading RAM, the screen does not work on Satellite L30 - 105

    Dial up on laptop and screen does not work. Have updated the memory to 2 GB.
    This can be the reason of the screen works not? Have tried rebooting the system, but it helps t n.

    Hello

    Can you please tell us which laptop model you have? Have you noticed the same problem until you do RAM upgrade?
    What's on the new RAM? Did you buy a compatible?

Maybe you are looking for