Case 'not the same subnet mask' - WRT54GL

Hello

I recently bought a WRT54GL router and tried to feed it with data from my ISP.

I entered these data to my Windows system as well as my older router and it worked fine.

These are:

IP: 213.211.57.xx

Subnet mask: 255.255.255.0

Gateway: 213.211.56.1

However, I get the error "not the same subnet mask" described here .

If I run "ipconfig/all" to the machine which can be used to connect to the net, I don't get any additional useful info that I described here, (he is also in Czech :-)

And there is no obvious conclusion in this forum thread.

Any suggestions?

Kind regards

Matej

OK, so I've solved this by changing the bridge and it works now.

Interesting that windows was able to deal with him, but...

Tags: Linksys Routers

Similar Questions

  • What are the vSphere components must be on the same subnet?

    VSphere components, those who need to be on the same subnet / vLAN?

    For example:

    vCenter Server and ESXi hosts?

    Groups separated from ESXi hosts are on separate VLANS / subnets? What is the limit of the number of hosts ESXi I should have on one vLAN to avoid having too much broadcast traffic?

    vCenter Server and he associated with SQL Server?

    VMware Update Manager and vCenter Server?

    VMware Update Manager and ESXi hosts it updated?

    There is no technical requirement that vSphere components must be on the same IP subnet. You can have all the components on a separate and routed (or even a firewall, you implement granted sufficient rules) subnet without problems. If that made sense, however, is a completely different question.

    vCenter Server and ESXi hosts?

    Does not really matter, but makes the most sense to be on the same subnet.

    Groups separated from ESXi hosts are on separate VLANS / subnets? What is the limit of the number of hosts ESXi I should have on one vLAN to avoid having too much broadcast traffic?

    If they are managed by the same vCenter, or similar commercial purposes, I would put them on the same subnet. I only consider something a subnet extra for things like DMZ-Clusters, that can be distinguished from any other as much as possible. A vMotion VLAN cluster might be a correct point in a normal scenario too.

    ESXi hosts really do not generate any significant broadcast traffic, apart from a few ARP requests here and there. This isn't Windows, after all, and even if that were the case, the time when you had to worry about the reasons broadcasting with 'only' a few hundreds or thousands of systems on a broadcast domain have long been more with the advent of fast and gigabit ethernet.

    vCenter Server and he associated with SQL Server?

    VMware Update Manager and vCenter Server?

    Even once it does not really matter, but I would put them on the same subnet unless I have a very good reason not to.

    VMware Update Manager and ESXi hosts it updated?

    As long as they are not connected via a WAN snail, causing the staging of updates hours, that's fine.

  • WiFi AR5007 802. 11 b / g adapter cannot talk about bridge WET11 Wireless on the same subnet

    Hello

    My HP Compaq Presario C700 VISTA laptop (a AR5007 802. 11 b / g WiFi adapter) and the printer are on the same subnet. The laptop is WiFi connected to my WRT54G2 router/switch and the printer is connected to the workgroup switch that connects to the router via the LinkSys WET11 Wireless Bridge.

    The installer works fine for over a year until he was there when my VISTA does not see any PC on the Working Group 3 weeks pass including the printer. However, the WAN access is not affected.

    I did the filming of following problems (in order):

    1. check the network settings on the laptop VISTA (x.x.x.29) and (x.x.x.201) printer and all look kosher.    (All my PC including notebook computer and printer have IP STATIC)

    2. check the router and the parameters of bridge and fines all eyes (router - XXX1, bridge - x.x.x.140).

    3 Ping printer, bridge, and other PC and received messages "Destination Unreachable Host" or "Request timed out". Although all are on the same subnet. Pingée router is OK.

    4 remove and re-add the wireless profile and tried to connect again. Same problem, no joy!

    5 started VISTA in safe MODE with NETWORK. Once again, the problem has persisted but at least eliminated applications as a potential source of problems.

    6. recycled power switch/router/workgroup bridge. No joy!

    7 WiFi connected other laptops to the same router (WRT54G2) and can ping other PC and printer END.    This means that the problem is limited to my VISTA laptop.

    8 given that the problem is on my VISTA and applications are not the source (see #5) of the problem, then probably the AR5007 802.11b.g wireless network card driver is original so I downloaded driver at HP and installed with version 7.3.201.25.  Problem is persistent...  Arhhh!

    Could there be something else that I missed? Can someone please help.

    Thank you

    You are the very welcome, John.

    Yes this driver will work fine on Vista Home Premium.

    According to the notes on the driver, it can just be run without uninstalling the current pilot you have on there now.

    After executing, you can confirm it 'takes' by going into Device Manager, expand network adapters, click the atheros wireless card, click the driver tab and you should see the installed version 2011.

  • public static IP on the same subnet of both internet and local

    I need to configure my little guy with ip static on the same subnet on the side of the router/internet and the side room, but it does not.

    I will allow me to dhcp on the side of the router/internet and then statically assign an ip address from the same subnet on the local side, but then it does not pass on my dhcp server dhcp queries.

    suggestions?

    Yes. Configure the WRT with a LAN inside your main LAN IP address. Disable the DHCP server on the WRT. Wire then a main WRT to your local area network LAN port. Do not use the internet port on the WRT.

  • Several groups of PS in the same subnet

    Is there something wrong with having two PS series groups (and, therefore, their members) in the same 24 subnet and the same VLAN?  We have a PS Group in the same place we are moving to another site that already has a PS Group.  We would like to just take advantage of the networking and configuration of VLAN, that we have so I just want to check that it is not a problem to do this.

    Thank you

    Bryan

    Hello Bryan,

    The only limits are the IP addresses available, switch ports available and that the switch can handle the load increases.  Especially if you share the SAN and LAN traffic to the same switch.  Also the link between the switches might need to increase as well.

    There is nothing inherit in the design to prevent it.   In my lab, I have quite a bit on the same subnet.

    Kind regards

  • Directly connected to the same subnet - still get 2 hops?

    I changed the ip numbers in this example of those public to the private sector

    | IP switch of the provider: 192.168.0.162/29. ------ | Reference Dell 6248 ip: 192.168.0.164/29 | ------ | Halon SX 200 ip: 192.168.0.166/29 |

    A Halon router for ip tracetroute: 192.168.0.163 says:

    1 192.168.0.164

    2 192.168.0.163

    Should not go directly to 192.168.0.163 with 1 jump? Am I missing something here?

    I've implemented a quagga and two HP Procurve 2626 router and could not reproduce the problem.

    Does anyone know if I'm missing something? In theory I should be able to simply get 1 jump to one IP address on the same subnet - right? Feels like the Dell switch made unnecessary routing...


  • Cannot open a Web site on the PCs of users, but the CD/DNS server in the same subnet to open it

    I'm trying to access a website of all pc sales and got an "Internet Explorer cannot display the webpage" error, but when I try it on a domain controller that is also a DNS server in the same subnet, I am able to access.  PC client when I ping the site I want access to I got "Request timed out" but not on the CD/DNS server.  Can someone please?

    Hello

    I suggest you to ask your question at the following link.

    http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/

    I hope this helps.

  • Surely the size measure LMT has not the same

    Hello

    If we identify not UNIFORM, surely the size of the measure has not the same.

    However, http://www.oaktable.net/articles/locally-managed-tablespaces States

    + You can ask yourself, "If a single bit is a measure, probably all extensions in the tablespace are then obliged to present the same size?". It's true -as in the example above, Oracle allows you to specify any size you like, but it will be always reduces to a number of bits of the bitmap, where each bit represents a segment of the space. In any case, it is advisable for all extensions in a tablespace to be the same size, because it eliminates the space lost because of the fragmentation. +

    Doesn't it not bad?

    Thank you.

    Published by: OracleGuy777 on March 13, 2012 13:16

    OracleGuy777 wrote:
    So, you're saying that each bit in the bitmap LMT will be the size as much as the lowest possible? And if we have a measure 1 M, it is going to be 1 024 000 bytes?

    Only the hard drive manufacturers use 1 000 000 bytes. The rest of the computer industry has pretty much standardized on 1 MB = 2 * 20.

    In addition, if the BLOCKS are 8K (or 2K, 4K, 16K, 32K) and 8 K = 8192 bytes, and if 1 MB MUST be a multiple of blocks assigned, you can check quickly enough that 1 MB = 128 x 8 K - BLOCKS. (And Yes, you can choose ANY size you want for a block, but that can get silly and will probably cause "opportunities for off-peak service calls").

    And we know that extensions are allocated in BLOCKS. (So why no Oracle used number of advancements of level measurement?)

    >

    So if we have a 64K extent, followed by a measure of 1 MB, followed by a measure of 64K, Oracle will store as

    1 followed by 1 s to 1 M and then 1 for the next measure 64K?

    To answer your question (even if it is answered on this link to the Oak Table - explicitly)

    The ILO plan represents the size of measurement RB. And non-linear growth that the system uses after distributing a few extensions will always be a multiple of the size of this base.

    Then the first few times the table grows, it will be in blocks of 64 k with each piece slightly.

    The next time it grows, it will say "I have seen the growth here before and to save effort later" so it will distribute pieces of 1 M. And a piece of 1 M is 16 x 64K, so each piece of 1 M will be represented by 16 bits. Then, after a few of those pieces of 1 M, it will distribute pieces of 8 M and guess how many 64 K parts there are in this 8 M chunk - each represented by one bit.

    And since all this piece pieces in this specific tablespace are 64K, if a table is dropped, all of its pieces can be distributed to other tables/segments as needed with no wasted space.

    That is the second reason to use LMT.

    Now you know.

    But, how does that help you administer the database? (Other than following best practices to use LMT?)

  • Documents InDesign CS6 for not the same pixel resolution

    I just opened in InDesign CS6, a document originally prepared in CS5.5. This document is in pixels. At 100%, the document must be pixel for pixel with my monitor (iMac 27 "to about 104 ppi), but it seems that it is more 100% if you calculate to 72 dpi. If a document of 980 pixel wide 13 inches on my screen! This is different from the previous way of showing pixel documents. And I don't see any preference that could bring resolution to the old way to show the scale.

    In Adobe Acrobat format, you have preferences to control it.

    This number as a bug to me.

    Spen says:

    Yes, I read your first post about the ratio of 1:1 ID. That's fine, but my questions remain. Why can I no longer specify text and traits using pixels? and why can I no longer see my files as they will appear in a browser. These features are available in CS5 they are now gone. Why?

    Your comment confuses me.

    Did you mean to say that you can no longer configure ID to display text units and traits as the pixels?

    This is not the same thing that you cannot specify text and strokes and pixels.

    So:

    • Ability to display dashes/fonts in pixels and not in points is a purely cosmetic function. Internally, ID treats points and pixels exactly the same.
    • Because it is aesthetic, and the calculation of points in pixels is really easy (the same number!), could you help us understand what is your real concern?
    • If you really want to, you can always type in "12 px" in the field.
    • I had the vague impression that when you created a Web document or an intention to Digital, then the specified unit is pixels instead of points. Appears not to be the case - my guess is that it's a screwup.
    • If indeed it was supposed to be automatic, I feel it's why the preference has been removed.

    (Incidentally, in the case where any who behind the scenes I was wondering, while the script API allow you to set this value in CS5.5, with app.viewPreferences.textSizeMeasurementUnits = MeasurementUnits.PIXELS; which doesn't seem to work in CS6, it generates an error: ' error: textSizeMeasurementUnits ')...

    To reiterate, I think it's probably a screwup in CS6 relating to a mismatch between what has been actually implemented (deletion of preference) and what was planned (automatic unit display) and not an intentional removal of the ability to show pixels. And yet, I do not understand why it really matters. What is a warm-fuzzy feeling you're looking for?

  • Transaction declined and last four numbers on the sheet, not the same as the card is used.

    Transaction declined and last four numbers on the sheet, not the same as the card is in my wallet.

    Hello

    The latest figures, rare are the last four digits of your account number of device, not the last four digits of your credit card.

    To see these numbers on your iPhone, go to: portfolio > tap to select this card > press the 'i' icon (bottom-right) > under the heading card, information the last few digits of your card number and your account number of the device.

    The account number of the device is related to the unique combination of your credit card, pay more the device on which it has been added to Apple (IE an iPhone, iPad, or Apple Watch).

  • How to determine if 2 IPs are on the same subnet

    Hi all!

    I have a Client/Server connection over a network, and I wants to determine if they are part of the same subnet.

    The server is installed on one OR cFP-2220, so I can't use all the exec system commands to access network settings.

    My code is so far simply determine if the client and server are both on the local host.

    Please see attachment!

    Concerning

    Paul

    Hello!

    Thanks for the reply.

    After a google search, I think it is the right way to do it: (Ref)

    XOR (B and H) (M & a)

    Thank you to direct me in the right direction!

    Kind regards

    Paul

  • Why date on the email received in my Inbox is not the same as reading mail?

    original title: E-mail Internet Explorer

    When I get a grateful e-mail that was read, the date on the e-mail received in my Inbox is different is up-to-date. However, the e-mail message when it has been read is not the same. Why is it so?

    Thank you, Daisy

    Hello

    You must ensure that your computer's date and the person responding to your emails should have the correct date and time.
  • Eql different groups on the same subnet

    Hello

    Quick question...

    We have a PS6000 four in a group of storage in an iscsi network 192.168.0.0/24. We have now bought two PS6100XV and think about maybe create another group of storage for the new boxes eql. The reason is in the future, upgrade to 10 GB on the new group.

    The question is if we create a new group to the PS6100VX, is it necessary to have a new iscsi LAN with a different IP subnet or can we use the same subnet 192.168.0.0/24 as PS 6000 are on?

    You can stay on the same subnet.   Your switch is the limiting factor.

  • I have uninstall by mistake my soundmax is there a way I can get this feedback? I tried to download another soundmax not the same I uninstalled. __

    I accidentally uninstalled my soundmax is there a way can I reteive this information.  I tried to download another soundmax not the same I uninstalled.

    Reinstall the audio drivers. You can find them in site of the either the card mother mftr. ; OR a Web site of OEM for your specific machine if you have a PC OEM (HP, Dell, Sony, etc.). MS - MVP - Elephant Boy computers - don't panic!

  • Separators from decimals/mile are not the same for the number and format of thousands. How can I get even. ?

    I installed the version 11 of Pastel partner and the error message "separators from decimals/thaousand for number and currency formats are not the same" how to get this right?

    Pastel partner support site through and their instructions/FAQ

Maybe you are looking for