Cause first of the wireless problem?

Similar Questions

• What causes use of the wireless mouse a lot of included

  I have to change my battreis in my wireless mouse a lot and I wondered why

  Hi carolyn

  The mouse you use it is obvious that the battery drains there don't you try rechargeable batteries and save money for yourself

• Energy management G580 causing wireless problem

  So first, I apologize if this post is in the wrong place. I saw nowhere g580s.

  I've narrowed my problems wireless for the Power Manager (I think).

  If the laptop is connected to AC wireless connects fine. If running on battery then it does not connect unless the energy management is set to 'performance' instead of the default "balanced."

  I'm on win8 and tried 8.0.2.5, 8.0.2.3 power management version and the latest version for win7 all with the same result.

  I unchecked the box in to the wireless network card device manager to "allow the computer to turn ff this device save energy."

  I just bought this laptop yesterday and it would be great if someone knew what I was dominant.

  Thanks in advance!

  Hi Artificialed,

  Thanks for posting back. Soha is correct. Usually this could be the cause of her managent Lenovo Energy I join n you can also try to check the power of window options. some setting it might have changed.

  To do this, please follow the steps below.

  > Go to 'control panel '.
  > Click on "Power Options."
  > Click "Change settings Plan" (located on the right)
  > Click "Change advanced settings" (located below on the left)
  > A new window should appear and find "Wireless Adapter" > "power save mode".
  > Change the settings "on battery" and "Trendy" to Maximum performance.

  Hope this helps and do post back with your results.

  Concerning

• OfficeJet Pro 8500 a - problem with the wireless radio

  First of all, I'm sorry for my bad English. I hope that you have little imagination when reading. I'll start to describe the problem and the lower list, I hope, all the relevant information you need to help me.

  Yesterday, I bought a brand new OfficeJet Pro 8500 has.

  Since I have found a little bit of my computer and my router I configure for wireless connection.

  All whent fine, the printer connected to my WIFI network without any problem and I was able to do a scan using the HP scanning software. How ever, when you try to scan a document nother directly after the first that did not work. I got an error message on the computer telling me that the computer could not connect to the scanner and it could be caused by the firewall. I also tried to print a word document, but it seemed that the document could not be sent to the printer during the observation of the State of the printer. Finally I gave up the print job and began to study the problem.

  By using the service to help in the HP software that I did all the things he suggested me to do. I have disabled the firewall, open TCP/UDP ports, restarted the router, the computer and the printer in different combinations, nothing worked.

  All the while the printer was connected to my WLAN, indicated by the State of the network printer and the router. I was about to give up but thought I should try only to disable and enable the transceiver wireless in the printer. To my surprise this solves the problem. I was in a position of scan and print documents.

  Today, after work, I tried to do another analysis, and the same mistake was present. Once more I did magic with the wireless radio and it has temporarily solved the problem, but he came back a few minutes later.

  Summoriz, the error can always be corrected by disable and enable the radio wireless, but after some time (a few minutes) the error returns that it self.

  I played a bit and discovered that it is possible to access the built-in Web server during the error. Not all functionality of the EWS seems to work perhaps (it's OK) but I can't among many things has see the State of the network and I can even do an analysis using the integrated Web server.

  I tried to reconfigure the printer using the printer setup wireless and also after a reset of the printer and it does not help.

  I hope someone on this forum knows a solution to my problem.

  Useful information:

  Computer OS: Windows 7

  Router: Thomson TG784 (I have an internet connection, phone and TV provider and this box takes care of this)

  Encryption: WPA - PSK

  WLAN: 802. 11 b / g

  No filtering MAC or SSID hidden

  Other devices on the network are two mobile phones and a Motorola Xoom Tablet

  Printers, IP address: 192.168.1.81

  Firewall: WIndows (the router is disabled)

  Concerning

  Thord

  Problem solved. Reinstalled the PC s/w has little time and finally he solved the problem.

• Wireless problem Compaq Presario CQ62 220 sv here is the solution! for 220 sv!

  Hi, I need help! Fast please I have a compaq presario CQ62 and do not work wireless

  I installed the driver for the wireless, but do not work

  is a BIOS problem? or anithing alse

  Please I need help! Fast!

  Thanks, Alex

  Sorry for my bad English!

  FAST!

  Update > I enter the device maneger and network controller is not installed

  Hardware ID >

  PCI\VEN_10EC & DEV_8171 & SUBSYS_1467103C & REV_10
  PCI\VEN_10EC & DEV_8171 & SUBSYS_1467103C
  PCI\VEN_10EC & DEV_8171 & CC_028000
  PCI\VEN_10EC & DEV_8171 & CC_0280

  Hello

  First of all, download and reinstall the Chipset driver from the link below.

  http://ftp.HP.com/pub/SoftPaq/sp46501-47000/sp46940.exe

  When this has completed, restart the laptop.

  When windows has completely recharged, download and install the Realtek WLAN driver at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp46501-47000/sp46673.exe

  Kind regards

  DP - K

• Impossible to connect a computer to the wireless network, I would like to first of all the automatic configuration service and I need advice.

  Article 861122 start WZC

  Unable to connect a computer to the network wirelee I firstly the WZC serviceand I need advice. TX

  Hello

  • Are you referring to Wireless Zero Configuration (WZC) Service?
  • What happens when you start the automatic Wireless Configuration Service?
  • You receive an error message?
   
  If you experience problems with the wireless network, reconfigure the Automatic Configuration Wireless for all wireless profiles automatically, click the fix this toolfrom the link below.
  Click run in the file download dialog box, and then follow the steps in this wizard.
  Error message when you try to run the Network Setup Wizard update for Windows XP Service Pack 2, Service Pack 3, or Windows XP Tablet PC 2005 Edition wireless
   
  See also:
  In Windows network connection issues
  http://support.Microsoft.com/kb/313242

• 4320 proBook s - problems with the wireless Assistant

  Hello

  I have my ProBook s 4320 for about half a year now. For most of the year the half I had problems with the wireless assistant - it seems that when I start my laptop it takes about 5 to 10 minutes before the work of the internet. I never changed any settings in the wireless assistant.

  Nobody does face these same questions and no one knows how the internet starts immediately when I start my laptop? I tried this on different places with different wireless modems, but everywhere, it's the same thing and books of other people can use internet immediately.

  Thanks in advance

  Hello

  You are welcome to help

  The fact that it connects properly in Mode safe indicates that the driver who normally starts with Windows or a program is causing the problem - most likely candidate is to begin by F-Secure.

  Before attempting the following procedure, make sure that you have an installation of F-Secure program, so you can re - install this software, and also a license key necessary to activate it.

  Then, from the windows control panel. Open programs and features, click on the entry for F-Secure once to highlight, and then click the option to uninstall at the top of the window.  Once done, restart the laptop.

  Again, when windows restarts, check the internet connection by using only a known secure site.

  Let me know how this affects the problem.

  Kind regards

  DP - K

• I started having problems with the wireless mouse and the carpet of my laptop - Lenovo ThinkPad T420 mouse.

  Original title: right click on the mouse itself activating

  I borrowed a USB to a person at work and I started having problems with the wireless mouse and the carpet of my laptop - Lenovo ThinkPad T420 mouse. The left click of two devices works normally, however, sometimes she does not respond to clicks and it takes a few seconds to work. The left button was constantly starts to turn on, as if he was stuck. After that I hit Alt + Tab and modify windows it stops for a few moments and starts at a later date. I havo not found a specific condition or a combination of keys that may trigger the fault.

  I read a few posts on discussion forums, but all say that it could be a hardware problem, which I think is not, because both devices have the same problem and I'm sure it all started with the insertion of the borrowed memory stick. I scanned the readers to help Symantec's EndPoint Protection and installed Microsoft Security Essentials and performed a full scan, but found nothing. I even restored the system, but the problem remains.

  Should I get a different antivirus? How can I find the cause so I can find a better targeted solution?

  Try to install the drivers from this link and check.

  http://support.Lenovo.com/en_US/research/hints-or-tips/detail.page?&LegacyDocID=MIGR-77167

• C7280 all in the a photosmart printer wireless problem

  Photosmart c7280 All in One

  Windows 7 64 b

  Unable to connect to the modem

  no change

  This photosmart c7280 all-in-one is no spring chicken, and there were no problems so far. It is connected to 2 laptops via a Qwest wireless modem. After that be able to connect to the printer for a week or two the ability to access the printer has disappeared... printer shows offline. To resolve this problem, I had to redo the SSID and WEP information and it would be upward. Today when this 'fix' again once he could not find the modem even if I am connected to my office at the top of the page and online. I had unplugged the modem and brought up in power go online without a problem, I so I stop the 7280 and restarted, is returned to Setup Wizard wireless, put in the news and hit OK... it has started the search for the modem then hooked! Unable to do anything, power button did not work, had to pull the plug to get it to turn off. Back on and everything but the wireless worked, did this x 4 with the same result. Is there a separate card to control the wireless function? It is replaceable and it sounds like the likely cause of the problem?

  Thank you, Bob

  Looks like the wireless card has failed.  Print a network Test Wireless in the network menu on the front of the printer.

  If she does not, reset the printer by turning it off, keeping the # 6 keys while a few seconds after turning it on.

  If the radio is toast, it can be practically replaced.

• I have a complaint on my Mac Book Pro. I bought my computer in January 2016 and it has two problems: the first is the display of the retina that has many traces of the keyboard and as many times it freezes. I have looked for help on the local Apple Store

  I have a complaint on my Mac Book Pro. I bought my computer in January 2016 and it has two problems: the first is the display of the retina that has many traces of the keyboard and as many times it freezes. I have looked for help on the local Apple Store and support too, but it did not help. I would like you help me solve this problem.

  Thank you.

  Kelly

  Your machine is still under warranty, so you should take it to your local Apple store for repairs. Function late in January, you bought it, you still have phone without support. If you can't find any help on the Apple Store, then I don't know what you expect to find here. We have no way to check for problems you have described or any additional hardware, etc.

• I keep having a problem with this error message. Firefox is already running but is not responding. To open a new window, you must first close the existing Firefox process, or restart your system. I've tried everything.

  I keep having a problem with this error message. Firefox is already running but is not responding. To open a new window, you must first close the existing Firefox process, or restart your system. I tried everything the internet suggested but it continues to wreak havoc... Help, please... John.I cannot give other details that it has become very annoying

  See "hang out":

  • http://KB.mozillazine.org/Firefox_hangs
  • Firefox crashes or does not - how to fix

• Satellite L875-13D - problem with the installation of the wireless card

  Hello

  I bought a Toshiba Satellite L875-13D. I installed Windows 7 Enterprise edition.

  I have a problem with the installation of the wireless card. I have downloaded the driver on Toshiba website, but it does not work. When I run the file .zip and .exe, nothing happens. In addition, there are several pilots: Athos, Intel and Realtek and I do not know what is mine... I test all the driver but same result.

  I have the same problem with Bluetooth driver that does not work too.

  Thank you for your help.

  > But it does not work yet for Bluetooth,... I have install the driver by the .exe from the Toshiba Web site but when I run the application, I have error that says missing tosbtapi.dll. I founded and downloaded and installed on budget3 and SysWOW. But after that, the installation is blocked. Any ideas?

  Laptop Satellite L875-13D isn t equipped with Bluetooth.
  Didn t you know who?

• Equium A60 - error caused by the RAM problem - Windows tool does not work!

  Hi all

  When closing my laptop, I got the blue "screen of death" and it restarts, windows came with this analysis of the accident: "error caused by the memory problem to live: run the Windows tool". I downloaded diagnostic tool (mstinst.exe), he opened so I got "windiag.iso" and he burned on a CD like they told me (the use of 'Record Now') and then I put in the CD drive and rebooted my computer. But it did not launch the tool! Does anyone know why it went wrong and how can I make it work? Even if I got the tool to work, I would be able to solve the problems of RAM anyway, just taking my laptop to a repair center?

  Thanks :)

  Hello

  I put t know if you have seen this page http://oca.microsoft.com/en/windiag.asp but there you can find a detailed explanation of how to use the Windows Memory Diagnostic tool.

  Good luck!

• HP deskjet f4580: problems with the wireless

  Hi I have. Printing HP deskjet f4580 and I try to connect to my wifi but it doesn't I look on the hp page and I try to do by pressing the wps, but it did not help me pls thx

  PS I have an iPad without a computer mobile o

  Hello! @Liz1712, thank you for joining the HP Forums!

  I understand that you have your wireless printer connection problems.

  Please try a few steps recommended below.

  On the printer Panel, hold down the button for two seconds wireless.
  NOTE:
  The printer starts a timer that allows two minutes to push the button of the wireless router WPS.
  Hold down the button the router WPS wireless for several seconds. The printer automatically detects the wireless network and then configure the connection.
  If your printer connects successfully to the wireless network, proceed to the next step.
  If your printer is not connected to the network wireless with WPS, you must use a temporary USB connection to set up your printer on the wireless network. Go to the next step.

  Please refer to this article for more information: http://hp.care/2c5GfmP

  Let me know the results!

  Have a great weekend ahead!

• Problem with the wireless on the system tray icon.

  Original title: wireless

  not found wirreless icon in the taskbar

  Hi Amourhbone,

  Thanks for posting your question in the Microsoft Community forum.

  It seems that you have a problem with the icon on the system tray wireless.

  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.
  Provide us with a few details in order to better understand the issue.

  1. which version of the operating system are you using?

  2. deal with any problem with the wireless network using Internet?

  3. do you receive any error messages?

  4. did you of recent changes on the computer before this problem?

  I suggest you try the procedure described in the article and see if it helps.

  System icons do not appear in the notification area in Windows Vista or Windows 7, you must restart the computer
  http://support.Microsoft.com/kb/945011

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.