CD/dvd drive does not properly

Similar Questions

• DVD/CD driver does not properly, the discs are not read.

  I tried different discs and none are read which is very annoying, because I can not install my new printer! When I checked the driver, the following message is displayed:

  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I click for solutions and he's looking for a few seconds and then nothing happens. I tried it 3 days ago and still today, but it still does not work, can I do?

  Thanks in advance for any help

  Hello

  19 code means there is a driver conflict such as two devices attempt to use the same resources.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.

  Normally the above will solve this problem otherwise working your way down through them, even if you did
  them before.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Satellite L500-126-CD/DVD drive does not open very well unrolled

  Hello

  I just got my second Satellite L500-126.
  I traded my first for a new because the ESCAPE key got stuck sometimes and made a grinding sound.

  Now, with my new one, I noticed that my dvd drive does not open very well unrolled and 2 bars of silver metal bit come out with the car when I open it.
  Is this normal?

  Also, when I close the dvd player, I hear a little noise "ping!"
  Like a spring, or something. Is that also normal?

  Thanks in advance.

  Hello

  I'm not quite sure what you mean by 2 small bars of silver, but the reader of my laptop s contains two metals (runners, railway).
  This is normal and these pieces are important to ensure that the drive can eject properly and could remain in a good position.
  Still, you will hear a short click Open and close the drive.

  So I guess it's ok.

• CD/DVD drive does not read discs on Equium A100

  My cd/dvd drive does not read any discs be it, white, written or commercially written. It opens and closes and is light to show that he is working on. Device Manager indicates that the device is functioning properly.

  Tried the update of drivers, no update available. Tried restoring the system back 1 day and 1 week and 1 month, then and still the problem cannot be corrected. When I put a cd/dvd in the drive and try to access it, it says: D:\ is not accessible. The request could not be performed because of an i/o device error.

  Can someone help me I tried everything my friends and I can think, or is it better to send just to toshiba warranty.

  If the solution proposed by James will not help, you should try to remove the drive to CD/DVD in Device Manager.
  After phone restart the operating system will recognize and initialize the disk again.
  After this review of the procedure if you can read, write the middle.

• Re: CD/DVD drive does not seem to start the DVD in Satellite P750

  My CD/DVD drive does not seem to start DVD, it runs and runs and the only way I can run a DVD (i.e. film) is using Windows Media Center, while the software to install must be enabled in Windows Explorer.

  Anyone?

  Help, please.
  Thank you!

  Have you tried to change AutoPlay settings?
  Open Control Panel and Auto game options. Enable the option Use AutoPlay for all media and devices. Also change other options, especially for DVD movies, software and games.

• CD/DVD drive does not work after 8 Win instalation

  Since a month since I've updated my windows in windows 8, everything works fine but the DVD - RW.

  When I put the blank cd and try to open it, it gives me error when opening by saying:
  "windows could not complete the format".

  Who's a software or a hardware problem?

  waiting for help!

  This means that your CD/DVD drive no longer works and is not recognized by the system?

  If Yes, then I would recommend checking this Toshiba document that I found on the portal of the knowledge base site:

  + Why my CD/DVD drive does not work after upgrade to Windows 8? +
  http://APS2.toshiba-tro.de/KB0/FAQ2B03F10002R01.htm

  You must uninstall the programs from Toshiba:
  TOSHIBA Recovery Media Creator
  TOSHIBA Disc Creator

• Satellite A100: CD/DVD drive does not appear in the Manager of peripherals and BIOS

  The CD/DVD drive does not appear in the window manager and I can't incert CD
  The BIOS displays "none" instead of "optical device".

  This means that the CD device is dead?

  Hey Micky,

  Unfortunately it's probably :-(. You can try to remove the optical drive and then reinsert it into Notepad, and then marketing and see if it is recognized as a new device.

  Check also that it is not displayed in Device Manager and if it is remove before trying the above.

  Kind regards

• My CD/DVD drive does not work

  My CD/DVD drive does not work, he plays any kind of disc, I don't think that my computer recognizes that it has a DVD player that more, please help!

  See this knowledge base article http://support.microsoft.com/kb/982116/en-gb

  Remove spyware, etc., can often mess up some registry settings that make it seems that the CD / DVD ROM drive is defective.
  HTH
  Neil
  www.nwarwick.co.UK

• DVD drive does not open.

  DVD drive does not open.  Won't open with the emergency eject button.  Once opened, it will close with the eject / close button.  How can I fix it?  This can cause the drive open suddenly do not?

  Thanks for any help you can provide.

  Hello

  · What is the number and the model of the computer?

  · Do you remember all the recent changes on the computer before the show?

  It seems to be the problem with the computer's hardware. You can check with the manufacturer for assistance on the same.

• My DVD drive does not appear in Windows Explorer

  This morning my computer ran a scan virus and other things, and when this was done, my computer will not respond to any type of CD.  No DVD, CD or even disks with files stored on them.
  When I open windows Explorer, the drive from DVD (e) is not even more appear.  I was wondering how to fix this.

  Hello

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• MY CD/DVD DRIVE DOES NOT READ THE DISC READABLE

  MY CD/DVD DRIVE DOES NOT READ ANY READABLE DISK ALL OF A SUDDEN.

  I DON'T KNOW WHAT IT IS.

  I CAN HEAR THE COMPUTER TRYING TO READ BUT IT ME SAID JUST THAT HE HAS NO DISC INSERTED OR THAT THE DISC IS BLANK WHEN ITS CLEARLY NOT.

  IT would NOT be RETURNING to PLAY AUDIO CD IN iTUNES or WINDOWS MEDIA PLAYER.

  HELP PLZ

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then check the cables
  both ends. Remove and replace, do not just tight. For laptops, you can often clean power
  and contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the system manufacturer
  and the manufacturer of the device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• CD DVD drive does not. Error code 10. Microsoft It planned is "fix.

  CD DVD rom does not.  Listed in Device Manager, with yellow warning sign, and when clicked, says Error Code 10.  Running Vista Edition Home Premium

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104
  Try the resolution on the following link:
  The CD drive or the DVD drive does not work as expected on a computer that is running Windows Vista
  http://support.Microsoft.com/kb/929461
  Also seethis discussion:
  FixIt did not work the first time
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/unable-to-write-to-DVD-drive-Windows-Vista/791d88ac-73b2-48da-a18c-723c0b08a587

• How to create a bootable Windows Vista USB drive? I can't install Windows Vista with a disk because my dvd drive does not work.

  I have install vista and I want to convey in the USB key... because my dvd drive does not work... Please tell me what I need to do

  Please send your reply to my email id, or post it here...

  Hello

  Vista is not designed to be installed like this.

  But others led to ways to do so.

  This may interest you on this subject:

  "How to create a USB of Vista Installation key '

  http://www.Vistax64.com/tutorials/181538-USB-bootable-Vista-installation-Flash-thumb-drive.html

  Google will help you in this matter.

   

  See you soon.

• CD DVD drive does not recognize inserted the disc: Code 19

  Windows cannot start the CD-ROM/DVD-ROM device because its information configuration (in the registry) is incomplete or damaged (Code 19). The CD-ROM/DVD-ROM device is a: HL-DT-ST DVD - RAM GH40L ATA Device on an HP Pavilion Slimline

  Hello

  Here are a few articles that will probably solve your problem.
  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista

  http://support.Microsoft.com/kb/929461

  Your CD or DVD drive cannot read or write media - A Mr Fixit

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  When you insert a CD or a DVD, Windows Vista may not recognize the disc

  http://support.Microsoft.com/kb/939052

  Mark <> Microsoft Partner

• Graphic drive does not properly.

  Graphics driver does not properly.  Screen will Dim and must restart to resume use.  Occurring more frequently now.  Y at - it a fix for this problem?

  Problem does not occur in safe mode.  Failure seems to occur on any key or the video style.

  Any material support is the manufacturer of the hardware regardless of the operating system that you choose to use.  As it is unlikely that you have a Microsoft video/graphics card - one you have and have you downloaded and installed the latest drivers/software they provide for your particular device?