CFP2000 cannot find the IP address

Hello
I recently reset my PSC-2000 to factory settings and it does not register its IP address with my router or it does not. I have moved the DIP-switch several times, but I'm unable to find it.
My network is defined as
10.0.0.0/28
10.0.0.1 - router

10.0.0.2 - 10.0.0.6 - open DHCP

10.0.0.7 PC with MAX and Labview
10.0.0.8 - open

The CFP is not accept an IP address from the router. How can I target this device to set the IP address, or to acquire one of the DHCP host. I don't have a serial RS232 cable into the unit.

The device is currently flashing red that it is at the stage of configuration factory

The device seems to be stuck in a guard dog. I found the problem and am now able to use.

Tags: NI Hardware

Similar Questions

  • Satellite Pro L20: WLan cannot find the IP address

    I just bought the Satellite Pro L20
    I have the ability to go wireless, but when I try to use it is not find my ip address?

    can someone help me? : D

    thanx
    Groovyjax xxx

    You should check the settings of the router. Check if the MAC address filtering is disabled.
    In addition, to access the WLan card properties and access the properties of the TCP/IP protocol.
    There you can check if the parameters are set on the automatically

  • Adding HP ePrint home and Biz iPhone app - mal printer cannot find the email address of the printer

    I'm trying to connect my HP Photosmart c6380 to my iPhone. I have already downloaded the app and my printer is connected to my wireless network, as is my iPhone, but I can't add my printer to the app.

    When I go to 'Manage ePrinters' and try to add a printer with the + button I see 3 choices:

    Add x to list: "no available ePrinters.

    Manually add: I can't find the printer even email address using the instructions available on the ePrint centre.

    Add the WiFi network: my printer is not shown in this list, so it does not support Autodiscover.

    So I guess that if I could just find email address of my printer that would connect to my iPhone for wireless printing, but I can't for the life of me find.

    Any help is greatly appreciated.

    Thank you.

    Hello amybett,

    I have bad news and good news. The bad news is that your printer is not Airprint/ePrint capable. However, the good news is that with the HP ePrint capable home and Biz iPhone app, it didn't need to be Airprint/Eprint, as it is connected to the same network as your phone.

    Here are the steps that you want to print something:

    1. installation of the application by filling in the electronic registration and entering the code (which I believe you have).

    2. Select the item you want to print by using the menu in the application (Photo Albums, files saved, Web browser, etc.).

    3. Once you select the item, you should see article and a big button "Print" under him.

    4. If the printer you want to print to is not listed above the 'Print' button, select the icon on the right (key/computer), and then select the printer you want to use (and other parameters).

    5. press the button 'Back' at the top left, then tap "Done" (blue top-right button) and then press the 'Print' button to print your article.

    Let me know if you still have problems after following the guide above.

  • P1102w - cannot find the printer

    Hello

    I'm unable to print using a wireless connection.

    the printer is p1102w.

    operating system is MAC OS 10.10 Yosemite

    Whenever I try to print something I get "printer is not connected / cannot find the printer" message.

    I tried the solutions on your support site, but nothing helped.

    For sure, printer is connected to the same network as the computer. I see it on the print configuration page and I can connect to its IP address via a web browser (but I can't use web services).

    All software and drivers are up to date. Update Apple is nothing new to me. Niether have your site.

    I tried to move the printer closer and further away from router. No results.

    No web proxy is related to my network.

    To make this work, I have to remove the printer from my system, reinstall it using the USB cable, and then add it again via wi - fi.

    But some time the problem reappears.

    It's really frustrating. Help, please.

    Hi @xopot ,

    I see that you have problems printing via wireless network. I would like to help you today.

    Since you can access the printer embedded Web server, the printer would have a valid IP address. Most likely, it has something to do with the software that the printer uses.

    Fix permissions of the drive on the Mac:

    Close all applications.

    In the Apple menu, click OK, click Applications, and then click utilities.

    Double-click disk utility.

    Highlight your hard drive / partition on the left.

    Click on check and then repair disk permissions.

    Restart the computer...

    Reset the printing system:

    Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

    Click on the Apple icon and then click on System Preferences.

    Click on Printers & Scanners.

    Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

    Click OK to confirm the reset.

    Type the name and the correct password.

    Click OK to reset the printing system.

    Then click on the sign to add the driver, highlight the printer +. (you may need to click the drop down menu to select the name of the printer) Then click the Add button.

    Configure a static IP address for the printer.

    The printer is not found during Installation wireless.

    Do not take into account the title. Select the Solution 4: assign your printer a static IP address.

    If you need help, let me know.

    Have a great day!
    Thank you.

  • Cannot find the printer HP Deskjet 3055 has wireless

    Hi bought this printer and went through the set up disc. The printer is connected and has the right signal to our home network and the laptop also connects wirelessley to the internet just fine. The laptop cannot find the printer - I tried all the suggestions and put the IP address for internet search and it will not. I can't understand. Also tried to install on the MAC laptop and still only goes up to now and then are unable to communicate with each other. Please can I have some advice.

    Oh, wait a minute--I just got it working by stopping laptop, printer and disconnect the wireless router and all start back them up again. Then to try to make it work on the MAC laptop - what this space! Thanks for the help.

  • Windows cannot find the specified path

    I am trying to start my Apple Mobile Device service, in administrative tools, in respect of Services and I get the error message 3. Windows cannot find the specified path. I am logged as administrator, while he was trying to do. I don't know why it won't let me do that. Help, please! Any input would be appreciated. Thank you!

    Hi msguyana_2000,
     
    Here's a post that addresses a similar issue. To resolve this issue, try the suggestion given in the post.
  • blue screen (setup), saying: Setup cannot find the files temporary installation and press f3, it is that I get

    Original title: unerase my hard drive

    I had a work beautifully computer (Dell INSP 6000) until I decided to add Media Center to my Xp - sp3. I bought the drive from a seller on ebay with numbers of coa who did not work. The drive has been formatted by attempts of constant relocation. Using XP and Media Center disks, I can get as much blue screen (setup) saying that Setup cannot find the temporary installation files and press f3. It's that I get. I also have a blue screen telling me to insert the diskette labeled 'Windows Automated System Recovery disk' in on the floppy drive. That's all. I am doomed.

    E-mail address is removed from the privacy *.

    How to request backup discs Dell

  • All of a sudden Outlook Express cannot find the files created by the method of attachment.

    Outlook Express cannot find the newly created files to attach. The files are there in My Documents and Outlook Express can still see all the old files, but each new file for the last month is not seen and cannot be attached. I even typed in the name of the file and it says can not find the file of the same name. I send you the files now through 'Send it' a service online, but complicated to use another program. I checked the 'views' and they seem ok. Help, please!

    It is a long shot, but try it in a new identity.

    File | Identity | Add the new identity. Create a new one and try it. If all goes well, you can import your messages and address book from the old identity and delete it.

    Note: Do not use the main word in the name of the new identity.

    How to create and use identities in Outlook Express
    http://support.Microsoft.com/?kbid=209169

    Bruce Hagen ~ MS - MVP [Mail]

  • An error occurred during the renewal of the Loopback Pseudo-Interface 1: the system cannot find the specified file. I use ipconfig /renew6.

    Hi all

    I use version 2.1 of WINPE. It works with ipv4 network services.

    I have a "Windows2008R2" machine in my network. In this server I am running a DHCPv6 server in my network. This server is the allocation of IPv6 addresses to all computers that have the OS Vista and Win7, etc (for vista and above).

    But I'm not able to receive the ipv6 address for winpe2.1 pc which is my test pc.

    What are the basic things I should do to receive the IPv6 ip address.

    If you please suggest me that how I can solve this problem.

    I tried to have run the command as "ipconfig /renew6" but he throwed an error

    An error occurred during the renewal of the Loopback Pseudo-Interface 1: the system cannot find the specified file.

    It is very urgent for me. I ask if anyone knows the steps so that the WINPE2.1 system get IPV6 will be appreciated.

    Thank you very much.

    Andy

    http://www.Microsoft.com/windowsserver2008/en/us/community.aspx

    They will help you in the community of Windows Server above with your questions.

    See you soon.

    Mick Murphy - Microsoft partner

  • Windows 7 cannot resolve the ip addresses of domain names

    I have a desktop computer that I built components purchased in a major computer store.  I got this system works well for several months, now.  Recently, however, I met a problem with one of the modules of memory of 2 GB.  I deleted (because it turned out to be defective) and, shortly AFTER his withdrawal, have another problem with the resolution of Internet domain name.  I have to say that I also installed my old Windows XP as an alternative OS and updated to sp3 (it is, in fact, that I use to access the internet and write this query).  As you can see, XP I have no problem with internet access or name resolution.  There are two other systems connected to the home network via wi - fi (one equipped with Windows Vista and the other a tablet PC running Windows XP Tablet Edition) and none of them have no access to the internet problem.  I ran ipconfig/release and / renew without any result.

    I did all the following: netsh winsock reset catalog
    netsh int ip reset reset.log
    netsh int ipv6 reset reset.log.
    Still no access.
    I opened regedit and went to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters and set the following registry value:
    Value name: IPEnableRouter
    Value type: REG_DWORD
    Value data: 1 (this is the only value I changed - from 0 to 1)
    I then exit regedit and reboot... still no access.  BTW: I noticed now that this entry (IPEnableRouter), nor any of its values, is no longer even exist in my registry.  I think it has something to do with my changing parameters of Cisco Linksys E1000 router to allow me access to my home network.  In addition, even if she says that I'm connected to my home network and the router, I don't see two other computers in the network, only the items that I share my desktop.
    I changed the "Preferred DNS server" to 208.67.222.222 as instructed in a possible solution I found on the web (in XP, of course) and, when it does not, changed to 208.67.220.220 instructions, but no.  Still nothing.
    I can access any Web site... IF I KNOW THE IP ADDRESS!  Unfortunately, my mind is not enough powerful or with enough RAM to remind all the IP addresses that I never go, not to mention every single IP address in the internet.
    If I had remembered to I have copied to Notepad (so I could then copy here) the results of an ipconfig/all command, but I didn't.  If this will help, let me know and I'll get it and post it.  I know that some errors I have received are 'Windows could not automatically detect the network proxy settings"and"registration of the DNS records failed.  The parameter is incorrect"and" an error occurred during the liberation interface Loopback Pseudo-Interface 1: the system cannot find the specified file. "
    Some of the results of an ipconfig/command all, I write down, such as those that came out as strange or maybe wrong.  They are as follows:
    Active IP routing: NO
    WINS proxy enabled: NO
    Host name: (empty)
    Suffix primary DNS: (empty)
    Node type: hybrid
    DNS suffix search list: News:[email protected] (Yes, I use Road Runner by Time Warner, and no, they were not able to help at all)
    Other results:
    ISATAP.KC.RR.com tunnel adapter
    State of the media: Media disconnected
    Card tunnel Teredo Tunneling Pseudo-Interface
    State of the media: Media disconnected
    Please keep in mind that all computers connected to this wireless router have no problem with access to the internet and this computer can access in Windows XP but not Windows 7.  In other words, is there anything wrong with the router and nothing wrong with the wireless network adapter.  Besides, I tried to reboot the router and even resetting (much to the chagrin of my other significant because she was not happy with not being able to access the internet until I was finally able to re - install the router)
    !).  I have also turned off my system, removed the card wireless adapter, waited for about 15 minutes, re-inserted in the PCI slot and return to market the system.  This, of course, did nothing, either.
    After the search for several days and trying various tactics and bugs as suggested all over the web, I'm at the end of my limited knowledge and patience with this problem.  Any help that will solve this problem and allow my Windows 7 to access, once again, the internet would be greatly appreciated.  As a last resort, I might have to re - install Windows 7, but I also read the posts where others have done so, but nothing helped. :(
    Thank you
    Lakusus
    The system configuration:
    Windows 7 64 bit Home Premium 32-bit of Windows XP Home Edition operating systems and in a dual-boot configuration
    Card mother ASUS M4A89GTD PRO series
    AMD Athlon (TM) II X 4 640 clocked at 3.49 GHz
    2.00 GB of RAM
    Linksys Wireless-G PCI adapt
    Graphics card XFX ATI Radeon HD 5750 card w/1 GB GDDR5 memory
    Two hard drives 1 TB SATA and a 250 GB HARD drive partitioned into a total of 10 discs
    Burner DVD HL-DT-ST DVDRAM

    In fact, I have since fixed my problem.  Believe it or not, it wasn't any major and detailed process.  It was a very simple thing that NONE of the resolutions on that I read even suggested might be the cause, so I don't even think to check it out.  Apparently, at any given time a week ago, or NAME of the COMPUTER, something erased my!  I forgot how I found this, but I think that I went to my device manager by double-clicking on the icon "Computer" and select 'Properties' and happened to notice that, under 'Settings of computer name, domain, and workgroup', the ' computer name: "and" full computer name: "fields were empty!

    SO, I clicked on 'Advanced system settings' on the left of the window properties, select the "computer name" tab (1st one at the top left of the window that has popped up) and down to "to rename this computer, click on change." I clicked on the button 'change... '. ».
    In the next window which displayed I got the name I initially chose for my desktop, clicked the button "More"... ' and 'News:[email protected]' in the ' suffix main DNS on this computer: "on the ground (as is my Internet service provider - others may be different) and ensured that the box"Change the suffix main DNS when the domain membership changes"has been checked.
    Then, I clicked OK on this window.  I then made sure that the "Working Group:" radio button was selected and typed "WORKGROUP" in the field below, then click 'OK '.
    Return to the window' system properties 'original, I clicked 'Apply' and 'OK' and then restarted my system.
    Windows 7 being loading, all of a sudden all these programs that were inactive for the past few days began to appear and load and update!  YAY! Laughing out loud
    So, the reason I went into detail about how I solved it is in case anyone else has this same problem, they can check and, if the computer name has also been deleted, follow these steps to correct the problem. Of course, you will need to contact your service provider (if other than the Road Runner by Time Warner) in order to obtain the primary DNS suffix.  I hope this will help others I do not go through the terror I lived not having access to the internet.  Aaaaarrrrggghh!  I MUST have my internet! LMAO
  • New Win 7 computer cannot access the IP address of the network printer. Help, please.

    Greetings,

    -----------------------------------------------------------------------------------------------------------------------

    UPDATE: we have found the solution to this problem, we, and that I posted an explanation as well as two ways to solve the problem in my 2nd post on May 5, 2015. Scroll down to it for the solution. Unfortunately, Microsoft does not allow the OP to mark one of their own messages as 'the Answer' so this thread continues to be listed as "no answer" when he actually answered me.

    -----------------------------------------------------------------------------------------------------------------------

    The original message follows...

    We cannot sign a new Win 7 (64-bit) computer to a printer ethernet established in our local network of 'working '. We have reached the limit of our troubleshooting skills and expertise assistance.

    Our Local network
    ------------------------
    The printer is a Dell 5100cn workgroup laser that is connected via an ethernet cable to a 10/100 workgroup switch 5-port Cisco/Linksys. The switch is connected to the built-in cable Motorola modem / 4 port gigabit router / WiFi access point. There is no server between the printer and the network.

    Other computers on the network run also Win 7 and have no trouble seeing and using the printer. Some computers are connected via a gigabit ethernet cable to the router Motorola. Other computers connect wireless WiFi (once again, by the same Motorola device). All computers, including the new ones, are attributed to the same workgroup.

    The printer has a static IP address. It also has an integrated Web page accessible within the network via a browser to view the status of the printer. All previous computers can view the status of the printer Web page by entering its IP address in a browser.

    The new Win 7 computer
    --------------------------------
    At the Windows command prompt, we successfully ping the IP address of the printer and received a return signal. However, we are unable to connect to the IP address of the printer (and status Web page) with a browser. And we cannot find the printer when install us the printer driver. We have tried to turn off the Windows Firewall and it did not help.

    When we install the driver, move us as a 'local' printer and create a new "Standard TCP/IP Port" for her. We enter the static IP address of the printer and name the port. Define us the Protocol to "LPR", enter the name of the queue ("lp") and activate SNMP State with name of the 'public' community and the index "1". These settings have worked very well with our previous computers.

    When the time comes to 'choose printer', we select 'have disk... '. ' and use the Dell 64-bit for this printer driver. But it does not work and do not print a test page. We even tried to install the printer as a 'network' printer driver, but it does not, either. In addition, the 'local' method always seemed to work best in the past.

    The new computer has no harm to see other computers and devices on the network. For example, there is a NAS connected to the same switch Cisco/Linksys like the printer and the computer can access the NAS via its static IP address. The new computer can also access the internet. He can't use the IP address of the printer. We even tried to change the address IP of the printer, but that did not help either.

    Despite the fact that the work - the network troubleshooter Windows command prompt ping indicates that the printer is not responding. What do we lack? Help, please.

    Greetings,

    I hope that this will be our last post on this subject. We have discovered the source of the problem and can offer two 'fixed' in case someone else runs into the same situation.

    With the help of MSConfig and a process of elimination, we have disabled non-Microsoft services that were running on the computer until we discovered that "Qualcomm Atheros Killer Service V2" was the source of the problem.

    Explanation

    ----------------

    Our new Win 7 computer contains a communication module ethernet/WiFi/Bluetooth e2200 Qualcomm Atheros. The manufacturer provides a '' Killer Network Manager '' for this system. Its purpose is to monitor and control the flow of data over a network connection in order to optimize for. For example, the user can choose to give the program A high priority and program-B low priority. This ensures that the program-A is less lag in the network traffic.

    The primary market for this function, so far, has been the online game (where the name of 'Killer'). It allows players to channel the bulk of the bandwidth available to their game and away from other programs and services that are running at the same time. A response faster online gives the player the advantage it needs to get "kill him" before someone else.

    This system of control of bandwidth has interfered with data packets of return of our network, clearing communication between our computer and our printer printer.

    Difficulty 1

    --------------

    The simplest solution for us was to disable 'Qualcomm Atheros bandwidth control' for the ethernet NIC that has been accomplished by going to: Windows Control Panel > network and Internet > Network and Sharing Center > change the settings of the card (in the sidebar). Then we clicked on our connection to the LAN (our NETWORK ethernet card) and select the 'Properties' command Finally, on the Networking tab, we have disabled 'Qualcomm Atheros control bandwidth' and clicked 'OK' button to close.

    All that was needed after that was a quick restart and we were able to access our printer even with the killer Network Manager and functioning of Qualcomm Atheros Killer Service V2.

    Either way, we left the control function of bandwidth enabled for wireless (our) network connection because we do not plan on using this network printer when the computer is untethered to ethernet.

    Difficulty 2

    --------------

    If you don't want the killer running Network Manager on your computer, you may be tempted to uninstall. Do not! Uninstall will also uninstall the drivers needed for your ethernet, WiFi and possibly your Bluetooth as well. We heard that some users have communicated with Qualcomm and were able to coax, on their part, the necessary drivers comm without luggage "Killer". But you don't need to do it, either.

    All you need to do is: (1) remove the 'Killer Network Manager' of the '"start up" folder of the start menu of Windows (under "programs") and (2) using MSConfig, uncheck "Qualcomm Atheros Killer Service V2" under the ' Services ' section. Then reboot and you're good to go. The killer Network Manager and his service will not work.

    Moreover, the reason for which we did not chose this method, ourselves, is because we see one deserves that available Killer Network Manager so that we can block network traffic to select programs. Solution 1 converts this easy thing because the Ethernet bandwidth control can be quickly activated again if she is ever desired. And we're leaving it enabled for our WiFi.

    Best regards, David-EH

  • Cannot find the printer on the wireless network

    My new 6500 a 710n-z printer copier copies very well.  Also, it detects the wireless network and is given an address 169.254.182.35.  I have reset the router several times using the WPS button.  But after I installed the software on my netbook ACER Windows XP, the computer cannot find the printer.  I spent three days trying to get the $% # ^ & * to work.  I see in some documents to get a 169.254. IP address, so I'm probably not connected?  But what to do?

    Well Yes, a 169.254 IP address... is auto-assignée when he can't get one from the router.  The WPS button does not reset the router.

    Do this on the printer: Setup > network > Wireless Setup Wizard. Follow the instructions.

  • I tried all these steps and still no progress, cannot update or restore my phone. When you try to restore an error appears saying 'cannot find the phone (9).

    I tried all these steps and still no progress, cannot update or restore my phone. When you try to restore an error appears saying 'cannot find the phone (9).

    We do not know what are the following steps, because you have not provided their. Support this article has suggestions for your specific error code.

    If you see errors 9, 4005, 4013, 4014, when you restore your device iOS - Apple Support or

  • Is there a way to find the IP address associated with a device that is currently using my Apple ID?

    Hi, is it possible to find the IP address associated with a device that is currently using my Apple ID? There is a device currently using my Apple ID, and I would like to know its IP address. When I connect to appleid.com, the device is listed. The device is an iPhone. It is an emergency situation. Thank you.

    Unless it's on your local network, the IP address won't be useful to you in any way. (and no, you can do that)

    If this is really an "emergency", inform the authorities.

  • Cannot find the seetings camera

    Cannot find the camera settings in firefox os smartphone

    Hi sanatankumarsahu,

    What settings to configure for your Firefox OS device camera?

    There is no specific menu of camera settings, but depending on your device and the version, you can choose another camera, turn flash power or reset the focus.

    Please reply to this message with your Firefox OS as well the version and the Build ID device model so that we can give you a definitive answer.

    Thank you

    -Ralph

Maybe you are looking for

  • Cannot run Windows 7 SP1 on big HDD (1 TB)

    Hello I just realized about this very recent which is apparently now closed: http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=275105 I had same problem with a Toshiba 1 TB drive - I lost on that day and tried at least 10 Window

  • can I put my taskbar across two monitors?

    I hooked to a monitor to go with my laptop and I want the taskbar to be available on both screens. I want to continue to use the dual monitors as separate screens (I put "extend these screens") can I do? Also if there is another cool thing I should k

  • An error 0 x 00000643 attachment with the installation of the printer

    I am running Windows Vista on a laptop and I am trying to install a wireless printer.  I get error 0 x 00000643.  I went to the windows support center and performed all workaround solutions that he suggested.  The WSD port has been deleted, but whene

  • CSK/signature of rejected password - server problem? CRITICISM

    Hello I am unable to get Momentics to accept my password of KSB when you download a debugging token for the device. I did not change the password. It worked fine for months. Password has not changed. Device is properly connected to Momentics. Is the

  • Simple question - why doesn't this long text vertical field?

    It must be easy, but I spent too long trying to make it work.  I have a screen that displays a long string (EULA), followed by a few buttons.  I can not get the vertical scrolling text.  What Miss me?  I tried different combinations of indicators on