Changes of IPMI

Similar Questions

• Change the IP for UCS management pool

  Hi all

  We try to change / less the size of the property held by the pool for blades UCS KVM management.

  Some IP addresses are assigned to the existing blades, pourrais I delete existing IP pools directly and create the new compact block for managing KVM?

  If I like the above, I know I'll lose KVM on the blades.

  In addition, what is the impact? The trafffic server will be interrupted or blades restart?

  Thank you very much!

  Best regards

  No harmful impact other than to lose access MMIC for awhile (kvm, virtual media, IPMI etc.).  Blade will not restart you.  It's strictly a connection out-of-band management.

  Create your new pool, then zap your old.  The blades will be immediately wish through the other pool for an available IP address.

  Kind regards

  Robert

• Waiting for loading ipmi_si_drv - disable IPMI start?

  
  Hello

  I use a Supermicro X8SIL (without - F), a Xeon L3426, ECC reg., ESXi 5.5 16GiB!

  This forum is not compatible IPMI, and I think there is no way to install an expansion card.

  The quick start system until the ipmi_si_drv takes over - after 10 min. wait time - the system is starting up fine and works without any problem.

  In the vsphere client IPMI status is green! It's funny?

  Is it possible to minimize the waiting time at the start of the IPMI driver?

  Is there a modified ISO?

  Is it possible to disable the IPMI driver - I didn't have this feature.

  Best regards

  Matthias

  You can uninstall the VIB ipmi_si_drv as follows:

  First of all a series of tests to ensure that only this VIB is affected:

  # esxcli software vib delete--dry - run - vibname ipmi-ipmi-TR-drv

  Result of deleting

  Message: Dryrun only, host has not changed. The following installation programs will apply: [BootBankInstaller]

  Restart required: true

  VIBs installed:

  VIBs Removed: VMware_bootbank_ipmi-ipmi-TR - drv_39.1 - 4vmw.510.1.12.1065491

  VIBs ignored:

  Now for the actual deletion:

  # esxcli software vib remove - vibname ipmi-ipmi-TR-drv

  Reboot the host.

  You may need to put the host in maintenance mode before removing the VIB as well.

• Configure SNMP source for the events of HW for IPMI sensors

  Us run Dell hardware and tested OMSA installed on ESXi5 hosts pointing to OpenManage (OME) Essentials for any interruptions SNMP. As indicated in the following Dell FAQ for OME the 9.5 troubleshooting section, to avoid massive amounts of alerts unknown on the server of the OME from our hosts ESXi5 we define the SNMP CIM for IPMI event source.

  http://en.community.Dell.com/TechCenter/systems-management/w/wiki/3265.OpenManage-Essentials-FAQ.aspx

  This article as well as VMware material and KB, any reference to the need to use the vSphere CLI to make this change, which of course works such as documented. Does anyone know if it is possible to make this change via PowerCLI? We do not want to use the vSphere CLI unless it's the only possible way as all the other configuration items that we have implemented kickstart or PowerCLI scripting.

  http://KB.VMware.com/kb/1008065

  http://pubs.VMware.com/vSphere-50/topic/com.VMware.vSphere.monitoring.doc_50/GUID-01D333E8-0A34-4F04-BB6C-D80A5FDA8CC5.html

  I was able to find the key value pair in PowerCLI where EnvEventSource/directions options, but I don't know if those who may be changed.

  If someone knows a way to do this, I would like to know how it is possible.

  Thank you.

  I think I knew that.  It seems that you have to connect directly to the ESXi host nothing to do with SNMP still, but if someone knows a way to avoid this, I'd love to hear it.  But this seems to work at the same time, but would need to change to more than one host at a time.

  ## Script function: Modify SNMP source for hardware events
  ## Usage: Connect to vCenter where host(s) reside, populate constants below and run
  
  ## Host to make changes to
  $strVMHost = "your_ESXi_5_host"
  
  ## Credentials for ESXi host(s)
  $strUser = "root"
  $strPassword = "your_password"
  
  ## Key to change value on (in case there are different key/value pairs you need to change in the future)
  $keySnmpEventSource = "EnvEventSource"
  
  ## New value for above key
  $valueSnmpEventSource = "sensors"
  
  ## Connect directly to VMHost in order to see the HostSnmpSystem object (http://pubs.vmware.com/vsphere-50/topic/com.vmware.wssdk.apiref.doc_50/vim.host.SnmpSystem.html)
  Connect-VIServer -Server $strVMHost -User $strUser -Password $strPassword
  
  ## Get the VMHost .NET View object and select only the HostSnmpSystem object
  $viewHost = Get-VMHost -Server $strVMHost -Name $strVMHost | Get-View -Property ConfigManager.SnmpSystem
  
  ## Get the HostSnmpSystem object
  $viewHostSnmpSystem = Get-View -Id $viewHost.ConfigManager.SnmpSystem
  
  ## Create new empty HostSnmpConfigSpec (http://pubs.vmware.com/vsphere-50/topic/com.vmware.wssdk.apiref.doc_50/vim.host.SnmpSystem.SnmpConfigSpec.html)
  $specHostSnmpConfigSpec = New-Object VMware.Vim.HostSnmpConfigSpec
  
  ## Populate newly created HostSnmpConfigSpec object with current values
  $specHostSnmpConfigSpec = $viewHostSnmpSystem.Configuration
  
  ## Modify desired value for the matching key
  ($specHostSnmpConfigSpec.Option | ?{$_.Key -eq $keySnmpEventSource}).Value = $valueSnmpEventSource
  
  ## Reconfigure the SNMP agent to take the new value
  $viewHostSnmpSystem.ReconfigureSnmpAgent($specHostSnmpConfigSpec)
  
  ## Disconnect from VMHost
  Disconnect-VIServer -Server $strVMHost -Confirm:$false
  

  Let me know if it works for your environment that we not use SNMP in ours, so I didn't do extensive testing.

• How to set the parameters of the ipmi/ILO for feeding from a script management?

  I have an installation script entirely work for our guests esx4, the only thing missing is implemented ipmi/ILO settings.

  I searched and can't find answers for this, anyone know how to do it from a script?

  If it is ESX, so part of your kickstart could generate the thumbprint and download these results on a NFS server including vMA has access to perhaps a list of host names + digital fingerprint. You could write a small script which basically monitors a directory for updates and then automatically add to vCenter once the system is ready to go, you can probably do something similar with ESXi, but it will be more complicated that you have not a real way to "launch" the host. However, you can change the image and put your own scripts such as a python script to extract the footprint and again do the same thing by dumping at the exit of a volume shared including vMA has access to.

  If you are interested in editing script ESXi, take a look at 4 part of Maish's article on how you can configure the ESXi ping to a management host host - http://technodrone.blogspot.com/2010/04/esxi-deployment-solution-beginning.html

  =========================================================================

  William Lam

  VMware vExpert 2009,2010

  VMware scripts and resources at: http://www.virtuallyghetto.com/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".

• BMC and ipmi

  Hello
  
  I am new to RAC.i need to install it for implausible, I know where we need this BMC and impi?
  
  concerning

  you wrote:

  I am new to RAC.i need to install it for implausible, I know where we need this BMC and impi?

  BMC and IPMI have nothing to do with CARS himself.

  It has everything to do with server management - also called "+ lights out management + ' (LoM). Allows you to turn on a server that is out of service. Monitor the voltage and the temperature in the server. Monitor the log of hardware events in the server. Access the server console virtually. Etc.

  This is an important consideration for any production server (database, web, mail, etc.) to have implemented IPMI in place, hardened (change the default passwords) and configured for remote access to support and maintain the server.

  You need not have the IPMI kernel modules installed in the operating system that is used on the server. If you have, then you can use the o/s commands to query the IPMI data (voltage of the CPU, the fan RPM speed, etc.). However, the important issue is to be able to service processor of the remote access server and run the commands IPMI and LoM.

• I changed my Apple ID to my new married name, but somewhere it is still hanging on to my old details

  After getting married, I updated my Apple ID with my new name and e-mail address.  This well it worked and I can access iTunes etc but my iCloud storage is almost full and I tried to connect to improve it but it still shows my old email address and name.  I can't connect to it knowing that I replaced all the details so the old account doesn't really exist, but it will not display my new address.  I went in my Apple ID to see where he was always picking up the old name/e-mail since but there just my new details (as it should) and I don't see where it's always the old details.  How to forget my old data.  I have almost no storage iCloud and have no way to resolve this issue now.

  Thank you very much

  When you update the primary e-mail address on an account, you must then sign and return in everywhere that the account is used: what to do when you have changed your Apple ID email address or password - Apple support

  If you are being invited for the password of the account when you try to disconnect from the iCloud on the device and the computer test: If iCloud asks you the password to your Apple ID - Apple Support previous

• I need to change my security issues and said we do not have enough information to reset your

  I need to change my security but said Questions we have insufficient information to reset security of your apple ID questions.my is [email protected] I want to slove this problem please help me

  You should contact the account of Apple security team. To join, click here and choose a method; If this page does not list one for your country or if you are unable to call, complete and submit this form.

  (145174)

• How to change the name of iWatch

  For some reason when I bought the new iPhone 7 and complete matching, it has the wrong name.  I must say my name and my husband.  I have looked at everything in the watch/phone and may not know how to solve this problem.  Anyone has any ideas on how to get my name back?

  Thank you

  J

  Hello

  On your iPhone, in the application of the watch, go to: Watch My > General > topic > name - change the name as desired.

• Change of credit card deductions

  I am from Pakistan. I just change my credit card information and for whom I had 1 USD charged twice within 2 minutes.
  When I haven't bought anything, why me is she charged in the first place and who has also twice?

  Hello

  When a payment card is added or updated in iTunes Store, iBooks Store, App Store or Mac App Store, we can make a request for authorization to your card issuer.

  It's not a real charge, just a check to ensure that your credit card is active and can be used when you pay for your transactions.

  When a temporary authorization hold is placed on your credit or debit card, it will be only for a small nominal amount. For example, in the United States, you might see a charge of $1.00 USD.

  These charges will be removed automatically from your card account and shall not be paid.

  More information:

  Any payment holds card authorization in the iTunes Store - Apple Support

• How can I change several download Sierra systems

  How can I change several download Sierra systems?  I have a Mac mini end of 2012 running El Capitan, over a mid-2010 Mac mini and MacBook Pro mid-2010 the two race Yosemite with limit of bandwidth on my internet connection and want to update all three systems in one download.  Is the process that apply with Yosemite and El Capitan (ie. Copy the Setup program to another location before you run it on the download system) still the way forward?  Thank you.

  You can do this or DiskMaker X allows to create a key to install it.

  (145170)

• Change order number/special character artists

  I would like to know if there is a way to change the order of all the artists that begin with a number or a special character order. Currently, they are all sitting at the bottom of the list of the artist on the ipod (and iTunes) but I would like to have all displays at the top of this list.

  This is the sort order...  I think you would need to change the names of the artists so that they start with something that gets sorted at the top of the list in alphanumeric order.  For example, replace 10,000 Maniacs a_10, 000 Maniacs.

• Setting to change the number of days to sync e-mail

  Where the parameter move to if you want to change the number of days that will be synchronized to your e-mail accounts? Or he is let out iOS 10 for some reason any?

  vrmcw wrote:

  Where the parameter move to if you want to change the number of days that will be synchronized to your e-mail accounts? Or he is let out iOS 10 for some reason any?

  account settings - sync mails - 'Exchange' on my phone - spam day-

  Not an ios 10 issue that I don't have the function to my yahoo account.

  Maybe you should ask your email provider.

• Can I change the default folder for new documents Pages?

  When I run the application Pages, the first thing I see is a Finder window. For some reason, this Finder window invariably opens, not with the Documents folder, but in a specific subfolder of the folder images. Sometimes I use this folder as source for the photos that I insert into documents, but I don't want to see this folder every time I run the application Pages.

  How can I control this behavior? I see nothing in the preferences page to set a default value.

  When you launch Pages, you will be presented with a file picker (not the actual Finder). The left sidebar will be a folder of Documents, you must select. At this point, you can simply stop Pages. He will remember to open in the last selected folder and on the content of the Document folder, you will see a file chooser. As long you open, edit, save, or export documents in the Documents folder, it will remember this folder.

  If you change the location of the folder memory, whether it is in the file picker, or save or export to another location of the folder, and then the next launch of Pages will direct you to the last used folder location and not the location of the Documents folder.

  There is no user parameter which can be set to always override the behavior of Pages above.

• Every day someone is trying to connect my Iphone. Do I have to change my password every time?

  Every day someone is trying to connect my Iphone6. Do I have to change my password every time? How can I stop this?

  Your post says that someone is trying to connect 'on' your iPhone 6 - have - they possession of the phone or they try to connect your Apple from another device ID?

  Note also that there are a number of phishing scams that send e-mails that appear to come from Apple, but are not current. Do not use any links in these emails if you are not.

  If they are trying only to log in instead of sign in successfully it would be not necessary to change your password. However, you can consider on for Apple ID - Apple Support two-factor authentication or frequently asked questions about check in two steps for Apple ID - Apple Support (if available) for more security.

  If they are correctly connected, see: If you think that your ID Apple has been compromised - Apple supports